SEARCH · Engineering Papers

Results for “contact pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Temperature measurements in sliding elastohydrodynamic point contacts

Techniques using the infrared radiation emitted by a sliding elastohydrodynamic (EHD) point contact to measure oil film and surface temperature are discussed. Temperature distributions in the EHD contact are presented for a naphthenic mineral oil at 1.04 GN/sq m (150,000 psi) Hertz pressure and several sliding velocities. Film temperatures as high as 360 C are reported at locations near the points of minimum film thickness in the contact side lobes.

Turchina, V.↗

NASA NTRS2015

Shape Evolution of Detached Bridgman Crystals Grown in Microgravity

Detached (or dewetted) Bridgman crystal growth defines that process in which a gap exists between a growing crystal and the crucible wall. In microgravity, the parameters that influence the existence of a stable gap are the growth angle of the solidifying crystal, the contact angle between the melt and the crucible wall, and the pressure difference across the meniscus. During actual crystal growth, the initial crystal radius will not have the precise value required for stable detached growth. Beginning with a crystal diameter that differs from stable conditions, numerical calculations are used to analyze the transient crystal growth process. Depending on the initial conditions and growth parameters, the crystal shape will either evolve towards attachment at the crucible wall, towards a stable gap width, or inwards towards eventual collapse of the meniscus. Dynamic growth stability is observed only when the sum of the growth and contact angles exceeds 180 degrees.

Volz, M. P.↗

NASA NTRS1985

Lubrication of nonconformal contacts

Minimum film thickness results for piezoviscous-rigid regime of lubrication are developed for a compressible Newtonian fluid with Roelands viscosity. The results provide a basis for the analysis and design of a wide range of machine elements operating in the piezoviscous-rigid regime of lubrication. A new numerical method of calculating elastic deformation in contact stresses is developed using a biquadratic polynomial to approximate the pressure distribution on the whole domain analyzed. The deformation of every node is expressed as a linear combination of the nodal pressures whose coefficients can be combined into an influence coefficient matrix. This approach has the advantages of improved numerical accuracy, less computing time and smaller storage size required for influence matrix. The ideal elastohydrodynamic lubrication is extended to real bearing systems in order to gain an understanding of failure mechanisms in machine elements. The improved elastic deformation calculation is successfully incorporated into the EHL numerical scheme. Using this revised numerical technique and the flow factor model developed by Patir and Cheng (1978) the surface roughness effects on the elastohydrodynamic lubrication of point contact is considered. Conditions typical of an EHL contact in the piezoviscous-elastic regime entrained in pure rolling are investigated. Results are compared with the smooth surface solutions. Experiments are conducted to study the transient EHL effects in instrument ball bearings.

Jeng, Y. R.↗

DOE OSTI2025

Microstructure-Based Degradation Modeling in Solid Oxide Cells

The presentation is intended for a graduate class in Georgia Southern University taught by Dr. Hayri Sezer on electrochemistry, SOFC and Li ion battery. It summaries NETL's recent works on microstructure-based modeling of degradation in solid oxide cells. It covers the degradation mechanism of Ni coarsening, Ni migration and the build-up of oxygen partial pressure inside the electrolyte. The phase-field models developed for Ni coarsening and migration are reviewed and the results are compared to experiments in literature to examine different diffusion mechanisms (Ni self-diffusion, Ni(OH)2 diffusion in pores and Ni(OH) surface diffusion) and driving forces (Ni(OH)x concentration and Ni-YSZ contact angle change). It also demonstrates the developed model for oxygen partial pressure and shows that the predicted oxygen partial pressure can explain the Ni oxidation in the hydrogen electrode and crack growth on the electrolyte-oxygen electrode interface under certain operating conditions.

nickel coarsening↗

DOE OSTI2024

UO 2 solubility and chemical interactions in molten LiCl-Li 2 O

Here, this study investigated the solubility of UO 2 in LiCl-2 wt% Li 2 O at 650 °C with O 2 partial pressures up to 114 torr. Experiments were run in which UO 2 powder was contacted with the molten salt for up to 120 h. Salt samples were taken and analyzed for U and corrosion product concentration using inductively coupled plasma mass spectrometry and for Li 2 O concentration using titration. The highest measured U concentration in the salt was 0.06 wt%, and O 2 partial pressure was observed to have little to no effect on the solubility. Increasing O 2 partial pressure did increase the concentration of corrosion products in the salt. The concentration of Li 2 O in the molten salt progressively decreased with time in contact with UO 2 . This can be explained by the formation of Li 2 UO 4 via reaction of UO 2 with Li 2 O.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Measurement of Transverse Resistance for Stacks of Non-insulated REBCO Tapes

Transverse resistance among adjacent conductors is a key parameter to calculate AC losses in superconducting cables with non-insulated conductors. The transverse pressure insert (TPI) previously developed and used at Fermilab was modified to measure transverse resistance of stacks made of non-insulated REBCO tapes as a function of transverse pressure at liquid nitrogen temperature. Pressure up to 322 MPa was applied with a hydraulic cylinder. A small current up to 10 A was flown in the stack sample through REBCO tape leads spliced above and below the stack. The latter had a bending radius larger than 6 mm to prevent the critical current degradation in REBCO leads. The voltage was measured just outside the compressed area. Stack samples included stacks of bare 4-mm wide REBCO tapes, as well as REBCO tapes alternated with 4-mm wide stainless-steel ribbons of 40 μm and 30 μm of thickness. We herein present the results of these transverse resistance measurements. Results show a stronger dependence on pressure for smaller pressure vs. larger ones. Also, of the two components of contact resistance, i.e. contact and bulk, the latter was negligible.

Tamagnini, E. [Turin Polytechnic]↗

NASA NTRS1971

Bonding of reinforced Teflon to metals

Reinforced FEP Teflon composite material is bonded to a metal substrate by applying a thin layer of copper on the metal surface and disposing irregularly shaped copper particles on the coated surface. The reinforced Teflon is then assembled in contact with the particles, and the assembly is heated under pressure at an elevated temperature below the melting point of the Teflon. A diffusion bond stronger than the reinforced Teflon component is produced, thus enabling the fabrication of self-lubricating bodies with relatively high strength.

Laiacona, F. P.↗

NASA NTRS1971

Physisorption of Ar, Kr, CH4, and N2 on 304 stainless steel at very low pressures.

Determination of physisorption isotherms of these gases on stainless steel by pressure change measurements in very low pressure cryogenic baths where a steel nipple was brought in contact with the test gas at 77 to 90 K in a sealed constant-volume system. The position of the nipple in the gas was changed in such a manner that gas adsorption on a 47.5 sq cm area of the steel surface could be measured. The Dubinin-Radushkevich (DR) equation (1947) was used for an empirical description of isotherms at different temperatures. The mean adsorption energies calculated from the DR plots were 1290, 1545, 1490 and 1903 cal/mol for Ar, Kr, CH4 and N2, respectively, being about 10% higher than the corresponding values on Pyrex.

Troy, M.↗

NASA NTRS1986

Mass flow measurement of liquid cryogens using the triboelectric effect

A cross correlator technique using triboelectric technology has been shown to be a feasible method to measure liquid flow rate for liquid nitrogen and JP4 jet fuel. This technology, invented and pioneered by Auburn International, Inc., is also expected to be suitable for use with all other insulating liquids and cryogens. The technology described is particularly well suited for cryogenic use, since the sensor is non-contacting and non-intrusive, and therefore, causes no additional pressure drop within the flow stream. Further development of the in-line sensor is required to produce a prototypical version for the test purposes under SSME fuel flow conditions. However, with the knowledge gained from this feasibility study, it is very likely that an acceptable sensor design for a full test bed evaluation could be produced.

Dechene, Ronald L.↗

NASA NTRS1993

High-Suction Hydride Sorption Pump

Improved design provides high pumping speed at low pressure. Hydride-forming powder retained in thin layer in contact with inner surface of stainless-steel tube. Configuration provides large surface area and short path for efficient transfer of heat and small resistance to flow.

Bard, Steven↗

NASA NTRS2001

Ten Years in the Making: AUSM-Family

We begin by describing the motivations that gave birth to the original AUSM scheme and then focus on the ingredients that has spurred its growth and acceptance by the world of computational fluid dynamics. As it has played out more in the field, weaknesses have also surfaced. Hence, nutrients and supplements are prescribed to help it grow and stay strong and robust. In this paper, we will describe the saga of efforts owing to researchers who have contributed to building up the AUSM-family for the CFD community. It is hoped that a healthy scheme will contribute to the accurate and robust solution of problems encountered in a wide range of disciplines. We analyze numerical mass fluxes with an emphasis on their capability for accurately capturing shock and contact discontinuities. We will present a new scheme for the pressure flux, along with results for a host of test problems.

Liou, Meng-Sing↗

NASA NTRS2004

2003 NASA Seal/Secondary Air System Workshop

The following reports were included in the 2003 NASA Seal/Secondary Air System Workshop:Low Emissions Alternative Power (LEAP); Overview of NASA Glenn Seal Developments; NASA Ultra Efficient Engine Technology Project Overview; Development of Higher Temperature Abradable Seals for Industrial Gas Turbines; High Misalignment Carbon Seals for the Fan Drive Gear System Technologies; Compliant Foil Seal Investigations; Test Rig for Evaluating Active Turbine Blade Tip Clearance Control Concepts; Controls Considerations for Turbine Active Clearance Control; Non-Contacting Finger Seal Developments and Design Considerations; Effect of Flow-Induced Radial Load on Brush Seal/Rotor Contact Mechanics; Seal Developments at Flowserve Corporation; Investigations of High Pressure Acoustic Waves in Resonators With Seal-Like Features; Numerical Investigations of High Pressure Acoustic Waves in Resonators; Feltmetal Seal Material Through-Flow; "Bimodal" Nuclear Thermal Rocket (BNTR) Propulsion for Future Human Mars Exploration Missions; High Temperature Propulsion System Structural Seals for Future Space Launch Vehicles; Advanced Control Surface Seal Development for Future Space Vehicles; High Temperature Metallic Seal Development for Aero Propulsion and Gas Turbine Applications; and BrazeFoil Honeycomb.

Steinetz, Bruce M.↗

NASA NTRS2007

Subcritical Water Extraction of Amino Acids from Atacama Desert Soils

Amino acids are considered organic molecular indicators in the search for extant and extinct life in the Solar System. Extraction of these molecules from a particulate solid matrix, such as Martian regolith, will be critical to their in situ detection and analysis. The goals of this study were to optimize a laboratory amino acid extraction protocol by quantitatively measuring the yields of extracted amino acids as a function of liquid water temperature and sample extraction time and to compare the results to the standard HCl vapor- phase hydrolysis yields for the same soil samples. Soil samples from the Yungay region of the Atacama Desert ( Martian regolith analog) were collected during a field study in the summer of 2005. The amino acids ( alanine, aspartic acid, glutamic acid, glycine, serine, and valine) chosen for analysis were present in the samples at concentrations of 1 - 70 parts- per- billion. Subcritical water extraction efficiency was examined over the temperature range of 30 - 325 degrees C, at pressures of 17.2 or 20.0 MPa, and for water- sample contact equilibration times of 0 - 30 min. None of the amino acids were extracted in detectable amounts at 30 degrees C ( at 17.2 MPa), suggesting that amino acids are too strongly bound by the soil matrix to be extracted at such a low temperature. Between 150 degrees C and 250 degrees C ( at 17.2 MPa), the extraction efficiencies of glycine, alanine, and valine were observed to increase with increasing water temperature, consistent with higher solubility at higher temperatures, perhaps due to the decreasing dielectric constant of water. Amino acids were not detected in extracts collected at 325 degrees C ( at 20.0 MPa), probably due to amino acid decomposition at this temperature. The optimal subcritical water extraction conditions for these amino acids from Atacama Desert soils were achieved at 200 degrees C, 17.2 MPa, and a water- sample contact equilibration time of 10 min.

biomarkers↗

NASA NTRS2003

Improved Multiple-DOF SAW Piezoelectric Motors

Surface-acoustic-wave (SAW) piezoelectric motors of a proposed type would be capable of operating in multiple degrees of freedom (DOFs) simultaneously and would be amenable to integration into diverse structures and mechanisms. These motors would be compact and structurally simple and would not contain bearings or lead screws. One example of a particularly useful motor of this type would be a two-dimensional- translation stage. Another such example would be a self-actuated spherical joint that could be made to undergo controlled, simultaneous rotations about two orthogonal axes: Such a motor could serve as a mechanism for aiming an "eyeball" camera or as a compact transducer in, and an integral part of, a joint in a robot arm. The multiple-DOF SAW piezoelectric motors as now proposed would be successors to the ones reported in "Multiple-DOF Surface-Acoustic-Wave Piezoelectric Motors" (NPO-20735), NASA Tech Briefs, Vol. 24, No. 12 (December 2000), page 5b. The basic principle of operation of a multiple-DOF SAW piezoelectric motor is a straightforward extension of that of single-DOF SAW piezoelectric motors, which have been reported in several previous NASA Tech Briefs articles: For example, in the case of a linear SAW piezoelectric motor, piezoelectric transducers at opposite ends of a stator excite surface acoustic waves that travel along the surface of the stator. An object (denoted the slider) is pressed against the stator with sufficient pressure (in practice .300 MPa) that it remains in frictional contact with the stator at all times. The slider rides the crests of the waves and is thereby made to move along the surface of the stator. The direction of motion (forward or backward) is controlled by selecting the relative phase of waves generated by the two piezoelectric transducers. The speed increases with the amplitude of the waves and thus with the magnitude of the voltage applied to the transducers.

Bar-Cohen, Yoseph↗

NASA NTRS2014

High Temperature Dynamic Pressure Measurements Using Silicon Carbide Pressure Sensors

Un-cooled, MEMS-based silicon carbide (SiC) static pressure sensors were used for the first time to measure pressure perturbations at temperatures as high as 600 C during laboratory characterization, and subsequently evaluated in a combustor rig operated under various engine conditions to extract the frequencies that are associated with thermoacoustic instabilities. One SiC sensor was placed directly in the flow stream of the combustor rig while a benchmark commercial water-cooled piezoceramic dynamic pressure transducer was co-located axially but kept some distance away from the hot flow stream. In the combustor rig test, the SiC sensor detected thermoacoustic instabilities across a range of engine operating conditions, amplitude magnitude as low as 0.5 psi at 585 C, in good agreement with the benchmark piezoceramic sensor. The SiC sensor experienced low signal to noise ratio at higher temperature, primarily due to the fact that it was a static sensor with low sensitivity.

Pressure Sensors↗

NASA NTRS2014

High Sensitivity Stress Sensor Based on Hybrid Materials

A sensing device is used to detect the spatial distributions of stresses applied by physical contact with the surface of the sensor or induced by pressure, temperature gradients, and surface absorption. The sensor comprises a hybrid active layer that includes luminophores doped in a polymeric or organic host, altogether embedded in a matrix. Under an electrical bias, the sensor simultaneously converts stresses into electrical and optical signals. Among many applications, the device may be used for tactile sensing and biometric imaging.

Cao, Xian-An↗

NASA NTRSDate not supplied

Exploring the Geochemistry of Tholeiitic Basalts and Hyaloclastites Formed in Submarine Volcanoes for Comparison With Venus Lavas

Underwater basaltic lavas exhibit distinct rock textures, mineralogy and morphological differences compared to those formed on land, primarily due to rapid cooling caused by contact with cold seawater instead of air and to high pressures – similar to Venus. The geomorphological similarities between terrestrial submarine volcanoes and some morphological classes of Venusian volcanoes have been investigated, but a comprehensive comparison in geochemical terms has yet to be conducted. Only three missions to Venus (Venera-13, Venera-14, and Vega-2) were able to report bulk composition of Venusian rocks, while other four missions (Venera-8, Venera-9, Venera-10, and Vega-1) provided limited geochemical information. Using X-Ray fluorescent (XRF) analysis, we saw that rocks analyzed on the surface of Venus are tholeiitic and alkalic basalts. This study, as part of the “Analogs for VENus's GEologically Recent Surfaces” (AVENGERS) initiative, aims to examine the possibility of seamounts/submarine volcanoes lavas serving as analogues to Venus lava geochemistry and morphology/formational processes. By sampling and analyzing submarine lavas from three distinct tectonic settings on Earth - hot-spot, convergent margins, and divergent margins - we will assess in which tectonic context the analogy with Venus is most comparable. Fieldwork will be conducted in further detail for submarine volcanoes located in Sicily, Hawaiʻi, and the Southern Pacific (Fiji, Vanuatu, Tonga, Samoa); we will use previously collected samples where these submarine areas are not accessible. Sampling efforts will target areas likely to yield submarine tholeiitic lavas and/or hyaloclastites. Samples collected during fieldwork will undergo detailed whole-rock geochemical analysis, including XRF, X-Ray diffraction (XRD) and Inductively Coupled Plasma Mass Spectrometry (ICPMS). Thin sections will be used to constrain differences in morphology/textures. The obtained geochemical data will then be compared with existing data on Venusian lava geochemistry, allowing for a comprehensive evaluation of potential analogies between submarine lavas from Earth and volcanic rocks on Venus. By elucidating these similarities and pinpointing specific tectonic contexts, our study has the potential to enhance our understanding of Venusian geology and the possibility of ephemeral plate tectonics on the planet.

N Mari↗

DOE OSTI2023

Methods and systems for rebalancing electrolytes for a redox flow battery system

A rebalancing reactor for a redox flow battery system may include a first side through which hydrogen gas is flowed, a second side through which electrolyte from the redox flow battery system is flowed, and a porous layer separating and fluidly coupled to the first side and the second side, wherein, the hydrogen gas and the electrolyte are fluidly contacted at a surface of the porous layer, and a pressure drop across the second side is less than a pressure drop across the porous layer. In this way, rebalancing of electrolyte charges in a redox flow battery system may be performed with increased efficiency and cost effectiveness as compared to conventional rebalancing reactors.

Evans, Craig E.↗