Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “catalyst loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Improving Cost and Efficiency of the Scalable Solid Oxide Fuel Cells Power System

The objective of this project was to design and develop a 20kW range small-scale solid oxide fuel cells (SOFC) power system for applications such as data centers and commercial buildings. The original plan included a 5,000 hours demonstration and a Techno-Economic Analysis (TEA) which were dropped as part of project termination. The original project plan was to use a stack with a cross-flow cell design which had previously been tested for 500 hours at a community college in Malta, NY. However, it was decided to move to the advanced R-SOFC co-flow cell developed under Department of Energy Award DE-FE0031971. The advanced cell design has the advantage of a larger active area for the same manufacturing footprint which results in fewer required cells for the same stack power, hence a higher volumetric power density (kW/L) and lower cost per kW than the original cross-flow cell design. A full SOFC system Simulink model was developed and calibrated with testing data from a fuel cell stack and BOP (balance of plant) components. The simulation results from the calibrated model showed an acceptable match with the experimental data. A structural analysis conducted for various load scenarios indicated no high stress areas for all spatial directions. Major electrical system components were acquired, built and successfully tested. System sensors were verified and validated against controls. Safety checks, a diagnostic check, PID tuning, and control software commissioning tasks were also conducted. The power electronics prototype was delivered and trial testing completed. Balance of Plant component testing and simulation work was conducted to characterize Reformer-Heat Exchanger heat transfer and backpressure and reformer catalyst methane conversion and product selectivity. Simulations were conducted to design the Anode and Cathode fluid passages and size the air-air and fuel-fuel heat exchangers. A Burner operation map was created from test data and the Anode Gas Recirculation blower was tested to evaluate its durability. The SOFC system used a horizontal style design where components sit directly on a casting with a direct connection to the skid. This design has efficient packaging and a small footprint with approximate dimensions of 750 mm x 700 mm x 1700 mm. An SOFC system was built and successfully tested at the Malta, NY facility The system for over 500 hours under load of which over 300 hours was at full load of 20 kW.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Scalable Metal Phosphides as a Dual-Function Catalyst and Lithium–Metal Stabilizer for Lithium–Sulfur Batteries

Although lithium-sulfur batteries are a promising approach for achieving high energy density, their commercial viability is limited by poor sulfur redox kinetics, polysulfide shuttling, and lithium metal instability. To resolve these issues concurrently, we utilize titanium phosphides (TiP x ) as dual-function materials to catalyze the sulfur redox kinetics at the cathode and stabilize the lithium metal at the anode. Importantly, these phosphides are synthesized via a facile, highly scalable one-step mechanochemical ball-milling process that does not generate toxic phosphine gas as a byproduct, making it more viable compared to traditional synthesis routes. At the cathode, we find that higher phosphorus contents in the phosphide as in TiP 2 leads to superior redox kinetics and reduced polysulfide shuttling due to improved polysulfide adsorption ability. Meanwhile, at the anode, TiP 2 acts as a lithiophilic seed in a 3-dimensional carbonaceous host that can be lithiated to form a Li-TiP 2 /C composite. This composite alleviates the volume changes of lithium metal while utilizing TiP 2 to form a more favorable solid-electrolyte interface (SEI). Full coin cells employing TiP 2 in the cathode and anode were assembled with a sulfur loading of 4 mg cm -2 and a negative to positive capacity (N/P) ratio of 6. After 50 cycles, the TiP 2 full cells retain a higher capacity of 643 mA h g -1 compared to 422 mA h g -1 for the conventional cell, despite the higher N/P ratio of 12 for the conventional cell. Altogether, we showcase the viability of employing metal phosphides as catalysts in practical lithium-sulfur batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Ethanol Upgrading to n -Butanol Using Transition-Metal-Incorporated Poly(triazine)imide Frameworks

The upgrading of ethanol to n-butanol was performed using a molecular catalyst integrated into a carbon nitride support, one of the first examples of a supported molecular catalyst performing the Guerbet process. Initial studies using crystalline poly(triazine)imide (PTI) with lithium or transition-metal cations imbedded in the support together with a base as the catalyst system did not produce any significant amounts of n-butanol. However, when using the catalyst material formed by treatment of PTI-LiCl with [(Cp*)IrCl 2 ] 2 (Cp* = pentamethylcyclopentadienyl) along with sodium hydroxide, a 59% selectivity for butanol (13% yield) was obtained at 145 °C. This PTI-(Cp*)Ir material exhibited distinct UV–vis absorption features and powder X-ray diffractions which differ from those of the parent PTI-LiCl and [(Cp*)IrCl 2 ] 2 . Here, the PTI-(Cp*)Ir material was found to have a metal loading of 27% iridium per empirical unit of the framework. Along with the formation of n-butanol from the Guerbet reaction, the presence of higher chain alcohols was also observed.

Guerbet↗
DOE OSTI2025

A Full-Cell Model for Direct Toluene Electro-Hydrogenation Electrolysis

Liquid organic hydrogen carriers (LOHCs) are organic molecules that undergo a hydrogenation/dehydrogenation cycle to enable storage and transportation of hydrogen fuel under ambient conditions. One promising LOHC candidate is toluene, which can be converted to methylcyclohexane (MCH) electrochemically, enabling a decarbonized process when green electricity is used. In this study, we developed a full-cell model for the direct electro-hydrogenation of toluene to MCH, utilizing a zero-gap membrane electrode assembly architecture. The model incorporates electrochemical kinetics, ionic transport, water transport across the membrane, and mass transport effects. Electrochemical kinetics are characterized using Tafel analysis on Pt/Ru catalyst. The model is validated against experimental data, including polarization curves, Faradaic efficiencies, and water crossover. A voltage breakdown analysis shows that the performance is dominated by kinetic losses, and the model is used to carry out a comparison of different toluene electro-hydrogenation reaction catalysts. Finally, a sensitivity analysis is conducted on key design parameters illustrating which can be modified to maximize electrolyzer performance. The cathode specific surface area and cathode porous transport layer thickness (PTL) have the largest impact on the current density, while the PTL thickness and Pt loading in the PTL have the largest impact on Faradaic efficiency.

Ehlinger, Victoria M. [Lawrence Livermore National↗
DOE OSTI2025

Red-Light-Driven Biophotochemical Diode Based on a Microorganism–Silicon Nanowire Interface for Stable and Efficient Bias-Free CO 2 Reduction

Artificial photosynthesis offers a promising route for sustainable liquid fuel and feedstock production, yet integrating efficient CO 2 reduction catalysts with light-harvesting systems remains challenging. Here, in this study, we present a biophotochemical diode that couples microorganism-driven CO 2 reduction with glycerol oxidation, enabled by silicon nanowire photoelectrodes under varying red-light intensities. Tuning the biotic-abiotic interface─by increasing biocatalyst loading and adjusting the catholyte pH to mitigate local alkalization─significantly improves performance and stability. The enhanced-loading biocathode maintains a high faradaic efficiency across a wide potential range, even under elevated light intensities. At 60 mW/cm 2 , the system achieves a bias-free current density of 3.5 mA/cm 2 . Long-term stability testing at 40 mW/cm 2 demonstrates stable operation for over 100 h. The photoanode generates valuable C 3 products, primarily glycerate and lactate, enhancing the economic viability. This work showcases the importance of microenvironmental control at the biotic-abiotic interface and establishes a scalable platform for light-driven CO 2 reduction using earth-abundant silicon.

Artificial Photosynthesis↗
DOE OSTI2023

Atomic Layers of B2 CuPd on Cu Nanocubes as Catalysts for Selective Hydrogenation

The search for highly active and selective catalysts with high precious metal atom utilization efficiency has attracted increasing interest in both the fundamental synthesis of materials and important industrial reactions. Here, in this work, we report the synthesis of Pd–Cu nanocubes with a Cu core and an ordered B2 intermetallic CuPd shell with controllable atomic layers on the surface (denoted as Cu/B2 CuPd), which can efficiently and robustly catalyze the selective hydrogenation of acetylene (C 2 H 2 ) to ethylene (C 2 H 4 ) under mild conditions. The optimized Cu/B2 CuPd with a Pd loading of 9.5 at. % exhibited outstanding performance in the C 2 H 2 semi-hydrogenation with 100% C 2 H 2 conversion and 95.2% C 2 H 4 selectivity at 90 °C. We attributed this outstanding performance to the core/shell structure with a high surface density of active Pd sites isolated by Cu in the B2 intermetallic matrix, representing a structural motif of single-atom alloys (SAAs) on the surface. The combined experimental and computational studies further revealed that the electronic states of Pd and Cu are modulated by SAAs from the synergistic effect between Pd and Cu, leading to enhanced performance compared with pristine Pd and Cu catalysts. This study provides a new synthetic methodology for making single-atom catalysts with high precious metal atom utilization efficiency, enabling simultaneous tuning of both geometric and electronic structures of Pd active sites for enhanced catalysis.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microscopic 3D Graphene for High-Performance Supercapacitors with Ultra-High Areal Capacitance

Despite graphene being considered as an ideal supercapacitor electrode material, its use in commercial devices is limited because few methods exist to produce high-quality graphene at large scale and low-cost. We report a simple method to synthesize 3D graphene by graphenization of coal tar pitch with a K2CO3 catalyst. This produces 3D graphenes with high specific surface areas up to 2113 m2 g-1 and exceptional crystallinity (Raman ID/IG as low as ~ 0.15). The material has an outstanding specific capacitance of 182.6 F g-1 at a current density of 1.0 A g-1. This occurs at mass loading of 30 mg cm-2 which is 3 times higher than commercial requirements, yielding an ultra-high areal capacitance of 5.48 F cm-2. Moreover, the K2CO3 is recycled and reused over 10 cycles. The synthesis method and resulting electrocapacitive performance properties create new opportunities for using 3D graphene more broadly in practical supercapacitor devices.

Pham, Viet Hung↗
DOE OSTI2024

Influence of Ordered Mesoporous Oxides in Plasma-Assisted Ammonia Synthesis

Widespread implementation of dielectric barrier discharge (DBD)-assisted NH 3 synthesis, a nascent technology operating under sustainable, ambient conditions, is hindered by low energy yields due to, in part, poor fundamental understanding. Porous oxides used to support metal nanoparticle catalysts have shown significant energy yield contributions for DBD-assisted NH 3 synthesis even without metal. Using an AC-powered, coaxial, single-stage reactor at 16 kV with equimolar (N 2 /H 2 ) feed, we measured NH 3 synthesis rates in the presence of different nonordered oxides, ordered SiO 2 structures (SBA-15 and MCM-41), and ordered Al-incorporated analogues (γ-Al 2 O 3 -coated with varying Al-loadings and Al-substitution, respectively: Al 2 O 3 -SBA-15 and Al-MCM-41). We systematically quantified NH 3 energy yield dependence on pore structures and material identities (i.e., ordered pores and Al incorporation) known to facilitate higher DBD-assisted NH 3 synthesis rates. SBA-15 displayed a higher steady-state energy yield than MCM-41, indicating that framework type is a crucial factor, with both ordered porous systems outperforming fumed SiO 2 . 10 wt % Al maximized in situ NH 3 uptake among the various Al loadings, exhibiting a higher steady-state energy yield and similar power to SBA-15. However, Al-MCM-41 had a similar steady-state energy yield and lower power than MCM-41, likely due to the extended γ-Al 2 O 3 surface that has a dielectric constant higher than that of SiO 2 . Both Al-incorporated analogues benefit from surface acid sites that can adsorb NH 3 in situ, resulting in higher overall NH 3 energy yields than that of their parent ordered SiO 2 . Al 2 O 3 -SBA-15 shielded more NH 3 than Al-MCM-41, likely due to a higher acid site density than the acid site identity. Furthermore, Al incorporation via γ-Al 2 O 3 coating more successfully improves the NH 3 energy yield; together with the high-performing ordered framework, these analogues are potential metal catalyst supports with promising energy yields for DBD-assisted synthesis of NH 3 and other chemicals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Sulfur-doped graphene anchoring of ultrafine Au 25 nanoclusters for electrocatalysis

The biggest challenge of exploring the catalytic properties of under-coordinated nanoclusters is the issue of stability. We demonstrate herein that chemical dopants on sulfur-doped graphene (S-G) can be utilized to stabilize ultrafine (sub-2 nm) Au 25 (PET)18 clusters to enable stable nitrogen reduction reaction (NRR) without significant structural degradation. The Au 25 @S-G exhibits an ammonia yield rate of 27.5μgNH 3 ∙ mg Au -1 ∙ h -1 at -0.5 V with faradic efficiency of 2.3%. More importantly, the anchored clusters preserve ~ 80% NRR activity after four days of continuous operation, a significant improvement over the 15% remaining ammonia production rate for clusters loaded on undoped graphene tested under the same conditions. Isotope labeling experiments confirmed the ammonia was a direct reaction product of N 2 feeding gas instead of other chemical contaminations. Ex-situ X-ray photoelectron spectroscopy and X-ray absorption near-edge spectroscopy of post-reaction catalysts reveal that the sulfur dopant plays a critical role in stabilizing the chemical state and coordination environment of Au atoms in clusters. Further ReaxFF molecular dynamics (RMD) simulation confirmed the strong interaction between Au nanoclusters (NCs) and S-G. Furthermore, this substrate-anchoring process could serve as an effective strategy to study ultrafine nanoclusters’ electrocatalytic behavior while minimizing the destruction of the under-coordinated surface motif under harsh electrochemical reaction conditions.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Tuning acidity in silica-overcoated oxides for hydroalkoxylation

Mixed oxides are ubiquitious solid acid catalysts for a number of transformations. Here, the chemistry of mixed oxide interfaces was experimentally probed by constructing model SiO 2 on MO x interfaces using a liquid-phase, stoichiometrically-controlled deposition of tetraethyl orthosilicate (TEOS). Catalytically active Brønsted sites were generated in four series of overcoated SiO 2 on metal oxide materials prepared by depositing TEOS onto Al 2 O 3 , anatase TiO 2 , Nb 2 O 5 , and ZrO 2 . Pyridine DRIFTS studies indicate that the acidity of deposited silanol groups was enhanced by interaction with the metal oxide surface, suggesting that pseudo-bridging silanol type structures were formed. Trimethylphosphine oxide (TMPO) 31 P NMR experiments showed that Brønsted acid strength varied in the overcoated materials, with increasing strength in the following order: SiO 2 /ZrO 2 < SiO 2 /TiO 2 < SiO 2 /Nb 2 O 5 < SiO 2 /Al 2 O 3 . This order correlated with the Lewis acidity and chemical hardness of the underlying metal oxides. The catalytic performance of the materials was evaluated in the liquid-phase hydroalkoxylation of dihydropyran with n-octanol, revealing that activity was highly dependent on SiO 2 loading, which impacted the density of acid sites, and scaled exponentially with Brønsted acid strength, determined by the core metal oxide identity. Brønsted acid strength appears to be the key driver of the materials’ activity, with the highest areal rate of 2.2 mmol / m 2 – h being measured over SiO 2 /Al 2 O 3 . Furthermore, this study shows that SiO 2 -overcoated materials are a systematically tunable class of catalysts that can be applied to acid catalyzed reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Catalytic membrane reactor, methods of making the same and methods of using the same for dehydrogenation reactions

A catalytic membrane reactor and methods of operating and producing the same are provided that efficiently produces highly pure hydrogen (H2) from ammonia (NH3) as well as operates according to other chemical conversion processes. In one embodiment, a tubular ceramic support made from porous yttria-stabilized zirconia has an outer surface that is impregnated with a metal catalyst such as ruthenium and then plated with a hydrogen permeable membrane such as palladium. An inner surface of the ceramic support is impregnated with cesium to promote conversion of ammonia to hydrogen and nitrogen (N2). The resulting catalytic membrane reactor produces highly pure hydrogen at low temperatures and with less catalytic loading. Therefore, ammonia can be used to effectively transport hydrogen for use in, for example, fuel cells in a vehicle.

Way, James Douglas↗
DOE OSTI2023

Engineering a Self-Grown TiO 2 /Ti-MOF Heterojunction with Selectively Anchored High-Density Pt Single-Atomic Cocatalysts for Efficient Visible-Light-Driven Hydrogen Evolution

A photocatalyst TiO 2 /Ti-BPDC-Pt is developed with a self-grown TiO 2 /Ti-metal–organic framework (MOF) heterojunction, i.e., TiO 2 /Ti-BPDC, and selectively anchored high-density Pt single-atomic cocatalysts on Ti-BPDC for photocatalytic hydrogen evolution. This intimate heterojunction, growing from the surface pyrolytic reconstruction of Ti-BPDC, works in a direct Z-scheme, efficiently separating electrons and holes. Pt is selectively anchored on Ti-BPDC by ligands and is found in the form of single atoms with loading up to 1.8 wt %. The selective location of Pt is the electron-enriched domain of the heterojunction, which further enhances the utilization of the separated electrons. This tailored TiO 2 /Ti-BPDC-Pt shows a significantly enhanced activity of 12.4 mmol g -1 h -1 compared to other TiO 2 - or MOF-based catalysts. In conclusion, the structure-activity relationship further proves the balance of two simultaneously exposed domains of heterojunctions is critical to fulfilling this kind of catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Presentation of gas-phase-reactant-accessible single-rhodium-atom catalysts for CO oxidation, via MOF confinement of an Anderson polyoxometalate

Geometric or electronic confinement of guests within nanoporous hosts holds promise for imparting catalytic functionality, including single-metal-atom catalytic functionality, to existing materials. When the nanoporous host is a metal–organic framework (MOF), single-metal-ion catalysts have typically been installed by grafting to an open site on an inorganic node, with the node effectively becoming the support for the catalyst. This approach, however, imposes compositional constraints, as the node not only needs to be receptive to grafting, but also must be capable of stabilizing the framework against solvent evacuation, chemical exposure, and heating. Here, we show that disk-like, Anderson polyoxometalate clusters (RhMo 6 O 24 n- and Mo 7 O 24 m- ; POMs) can be confined in pore-specific and orientation-specific fashion within the hierarchically porous, Zr(IV)-based MOF, NU1K. Self-limiting loading of one cluster per pore, and associated nano-confinement, serve to isolate each POM and prevent consolidation caused by sintering. Additionally, the oriented confinement serves to expose individual rhodium atoms to candidate gas-phase reactants, while enabling the rhodium atom to employ a well-defined oxy-molybdenum cluster, rather than a MOF node, as a support. Synchrotron-based difference-electron-density maps and differential pair-distribution-function analyses of scattered X-rays establish cluster siting and orientation and confirm isolation. Nanoconfined (i.e., MOF- and POM-confined) single-rhodium(III)-atoms are catalytically competent for an illustrative gas-phase reaction, CO oxidation by O 2 , with the MOF-isolated POM enormously outperforming nonporous, MOF-free, solid (NH 4 ) 3 [H 6 RhMo 6 O 24 ]·6H 2 O. This paper highlights the value of MOF-based nano-confinement and oriented isolation of planar POMs as a means of uniformly presenting and stabilizing potent single-metal-atom catalysts, in reactant-accessible form, on well-defined supports.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Synthesis of Microscopic 3D Graphene for High‐Performance Supercapacitors with Ultra‐High Areal Capacitance

Abstract Despite graphene being considered an ideal supercapacitor electrode material, its use in commercial devices is limited because few methods exist to produce high‐quality graphene at a large scale and low cost. A simple method is reported to synthesize 3D graphene by graphenization of coal tar pitch with a K 2 CO 3 catalyst. This produces 3D graphenes with high specific surface areas up to 2113 m 2 g −1 and exceptional crystallinity (Raman I D / I G as low as ≈0.15). The material has an outstanding specific capacitance of 182.6 F g −1 at a current density of 1.0 A g −1 . This occurs at a mass loading of 30 mg cm −2 which is 3 times higher than commercial requirements, yielding an ultra‐high areal capacitance of 5.48 F cm −2 . The K 2 CO 3 is recycled and reused over 10 cycles with material quality and electrocapacitive performance of 3D graphene retained and verified after each cycle. The synthesis method and resulting electrocapacitive performance properties create new opportunities for using 3D graphene more broadly in practical supercapacitor devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

PdPt-TiO 2 nanowires: correlating composition, electronic effects and O-vacancies with activities towards water splitting and oxygen reduction

Here we report the optimization of both the support and the active phase of PdPt NPs supported on TiO 2 nanowires to obtain highly active electro/photocatalysts for the oxygen reduction and water splitting reactions. This system displayed strong metal-support interactions, high concentration of oxygen vacancies, and PdPt NP were ~2 nm in size. By optimizing the loading of PdPt, both the photo- and electrocatalytic activities were improved compared to commercial materials. Interestingly, a volcano plot was obtained from the activity and the PdPt composition, and the Pd 0.22 Pt 0.78 -TiO 2 /C sample afforded the optimal performance. For instance, the amount of hydrogen produced from water splitting was 11.6 mmol/g catalyst . For the ORR, the activity was similar to a commercial Pt catalyst, but a lower E onset (0.87 V RHE vs w 0.95 V RHE ) was detected. The variations in the activities with the composition correlated well with the variations in the electronic effects and the concentration of oxygen vacancies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Facet Impact of CuMn 2 O 4 Spinel Nanocatalysts on Enhancement of the Oxygen Reduction Reaction in Alkaline Media

Surface-structure engineering represents an attractive strategy to optimize the energy conversion performance of nanocatalysts using their deliberately controlled exposed facets. To further exploit the potential of non-PGM-based spinel catalysts for alkaline oxygen reduction reaction (ORR), a cathodic fuel cell reaction, we hereby report a strategy of ORR improvement by controlling the crystallographic facets of ultra-small CuMn 2 O 4 spinel nanocatalysts through a developed colloidal synthesis approach. The synthesis of CuMn 2 O 4 nanocrystals with morphological control relies on the design and selection of the Cu-/Mn-precursors with striking discrepancies in reaction kinetics. Following carbon loading and an annealing post-treatment of the as-synthesized nanocatalysts, the exclusively {101} facet-exposed CuMn 2 O 4 spinel nano-octahedra exhibit improved electrocatalytic activity toward ORR in 1 M KOH, when compared to their spherical counterparts, exhibiting a mass activity (MA) of 37.6 A/g at 0.85 V. After 10,000 cycles of ORR durability test, the nano-octahedra still retain an MA of 24.5 A/g, which is twice that of the CuMn 2 O 4 spinel nanospheres. Structural characterizations after durability testing indicate that the MA decay is likely associated with a decrease in the Mn 3+ fraction and the emergence of Cu + on CuMn 2 O 4 nano-octahedral surfaces. Finally, as a paradigm, this synthesis approach could be extended to other Mn-based spinel nanocatalysts with precise shape control, enabling us to understand and establish the relationship between the surface lattice/valence state and electrocatalytic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Atomic Structure Evolution of Pt–Co Binary Catalysts: Single Metal Sites versus Intermetallic Nanocrystals

Due to their exceptional catalytic properties for the oxygen reduction reaction (ORR) and other crucial electrochemical reactions, PtCo intermetallic nanoparticle (NP) and single atomic (SA) Pt metal site catalysts have received considerable attention. However, their formation mechanisms at the atomic level during high-temperature annealing processes remain elusive. Furthermore, the thermally driven structure evolution of Pt–Co binary catalyst systems is investigated using advanced in situ electron microscopy, including PtCo intermetallic alloys and single Pt/Co metal sites. The pre-doping of CoN 4 sites in carbon supports and the initial Pt NP sizes play essential roles in forming either Pt 3 Co intermetallics or single Pt/Co metal sites. Importantly, the initial Pt NP loadings against the carbon support are critical to whether alloying to L1 2 -ordered Pt 3 Co NPs or atomizing to SA Pt sites at high temperatures. High Pt NP loadings (e.g., 20%) tend to lead to the formation of highly ordered Pt 3 Co intermetallic NPs with excellent activity and enhanced stability toward the ORR. In contrast, at a relatively low Pt loading (<6 wt%), the formation of single Pt sites in the form of PtC 3 N is thermodynamically favorable, in which a synergy between the PtC 3 N and the CoN 4 sites could enhance the catalytic activity for the ORR, but showing insufficient stability.

36 MATERIALS SCIENCE↗