Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Effect of tail size reductions on longitudinal aerodynamic characteristics of a three surface F-15 model with nonaxisymmetric nozzles

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the effects of horizontal and vertical tail size reductions on the longitudinal aerodynamic characteristics of a modified F-15 model with canards and 2-D convergent-divergent nozzles. Quantifying the drag decrease at low angles of attack produced by tail size reductions was the primary focus. The model was tested at Mach numbers of 0.40, 0.90, and 1.20 over an angle of attack of -2 degree to 10 degree. The nozzle exhaust flow was simulated using high pressure air at nozzle pressure ratios varying from 1.0 (jet off) to 7.5. Data were obtained on the baseline configuration with and without tails as well as with reduced horizontal and/or vertical tail sizes that were 75, 50, and 25 percent of the baseline tail areas.

Frassinelli, Mark C.↗
NASA NTRS1993

The 3-D viscous flow CFD analysis of the propeller effect on an advanced ducted propeller subsonic inlet

A time marching Navier-Stokes code called PARC3D was used to study the 3-D viscous flow associated with an advanced ducted propeller (ADP) subsonic inlet at take-off operating conditions. At a free stream Mach number of 0.2, experimental data for the inlet-with-propeller test model indicated that the airflow was attached on the cowl windward lip at an angle of attack of 25 degrees became unstable at 29 degrees, and separated at 30 degrees. An experimental study with a similar inlet and with no propeller (through-flow) indicated that flow separation occurred at an angle of attack a few degrees below the value observed when the inlet was tested with the propeller. This tends to indicate that the propeller exerts a favorable effect on the inlet performance. During the through-flow experiment a stationary blockage device was used to successfully simulate the propeller effect on the inlet flow field at angles of attack. In the present numerical study, this flow blockage was modeled via a PARC3D computational boundary condition (BC) called the screen BC. The principle formulation of this BC was based on the one-and-half dimension actuator disk theory. This screen BC was applied at the inlet propeller face station of the computational grid. Numerical results were obtained with and without the screen BC. The application of the screen BC in this numerical study provided results which are similar to the results of past experimental efforts in which either the blockage device or the propeller was used.

Iek, Chanthy↗
NASA NTRS2012

Towards Reliable Evaluation of Anomaly-Based Intrusion Detection Performance

This report describes the results of research into the effects of environment-induced noise on the evaluation process for anomaly detectors in the cyber security domain. This research was conducted during a 10-week summer internship program from the 19th of August, 2012 to the 23rd of August, 2012 at the Jet Propulsion Laboratory in Pasadena, California. The research performed lies within the larger context of the Los Angeles Department of Water and Power (LADWP) Smart Grid cyber security project, a Department of Energy (DoE) funded effort involving the Jet Propulsion Laboratory, California Institute of Technology and the University of Southern California/ Information Sciences Institute. The results of the present effort constitute an important contribution towards building more rigorous evaluation paradigms for anomaly-based intrusion detectors in complex cyber physical systems such as the Smart Grid. Anomaly detection is a key strategy for cyber intrusion detection and operates by identifying deviations from profiles of nominal behavior and are thus conceptually appealing for detecting "novel" attacks. Evaluating the performance of such a detector requires assessing: (a) how well it captures the model of nominal behavior, and (b) how well it detects attacks (deviations from normality). Current evaluation methods produce results that give insufficient insight into the operation of a detector, inevitably resulting in a significantly poor characterization of a detectors performance. In this work, we first describe a preliminary taxonomy of key evaluation constructs that are necessary for establishing rigor in the evaluation regime of an anomaly detector. We then focus on clarifying the impact of the operational environment on the manifestation of attacks in monitored data. We show how dynamic and evolving environments can introduce high variability into the data stream perturbing detector performance. Prior research has focused on understanding the impact of this variability in training data for anomaly detectors, but has ignored variability in the attack signal that will necessarily affect the evaluation results for such detectors. We posit that current evaluation strategies implicitly assume that attacks always manifest in a stable manner; we show that this assumption is wrong. We describe a simple experiment to demonstrate the effects of environmental noise on the manifestation of attacks in data and introduce the notion of attack manifestation stability. Finally, we argue that conclusions about detector performance will be unreliable and incomplete if the stability of attack manifestation is not accounted for in the evaluation strategy.

cyber defense↗
NASA NTRS1997

Application of Wind Tunnel Free-Flight Technique for Wake Vortex Encounters

A wind tunnel investigation was conducted in the Langley 30- by 60-Foot Tunnel to assess the free-flight test technique as a tool in research on wake vortex encounters. A typical 17.5-percent scale business-class jet airplane model was flown behind a stationary wing mounted in the forward portion of the wind tunnel test section. The span ratio (model span-generating wingspan) was 0.75. The wing angle of attack could be adjusted to produce a vortex of desired strength. The test airplane model was successfully flown in the vortex and through the vortex for a range of vortex strengths. Data obtained included the model airplane body axis accelerations, angular rates, attitudes, and control positions as a function of vortex strength and relative position. Pilot comments and video records were also recorded during the vortex encounters.

Brandon, Jay M.↗
NASA NTRSDate not supplied

Comparing Methods to Extract Sectional Angle of Attack From Blade-Resolved Rotor Simulations

The angle of attack is widely used to describe the aerodynamics of rotor blades. Models based on lifting lines, actuator lines, and actuator disks use it as a primary variable, assuming the aerodynamics can be represented by the flow around a collection of equivalent 2D airfoils. This paper evaluates the accuracy of existing methods that extract the angle of attack from blade-resolved CFD simulations, towards enabling a direct comparison of angle of attack between blade-resolved and blade-modeled simulations. Results are compared for a 2D airfoil for which the angle of attack is known by definition. The hovering rotor case is also considered, where we look at two different rotor blades. We discuss the factors that impact the accuracy of the 2D predictions. For the 3D rotors, we show that three-dimensional effects in the root and tip regions lead to large discrepancies between methods. This suggests that the very definition of angle of attack is unable to accurately represent the flow in these regions. Finally, based on guidelines that we establish, we propose an alternate method that uses local velocities sampled on a contour located 0.25 chord, or less, away from the airfoil surface and generally yields improved accuracy compared to most existing techniques.

ARMD↗
NASA NTRS1982

Aerodynamic characteristics of a large-scale, twin tilt-nacelle V/STOL model

A subsonic tilt-nacelle V/STOL aircraft configuration is described which is powered by two turbofan engines, mounted on a single carry-through structure that is designed to maintain the thrust axis close to the center of gravity at nacelle incidences of 5-95 deg. Control during V/STOL operation, often from small ship platforms, is achieved by means of a vane assembly that is immersed in each turbofan's exhaust. Wind tunnel test data have been obtained with an 11.2-m wing span model for the vertical-to-horizontal flight transition capability of the concept. It is found that the aircraft can operate over a broad transition corridor, with sufficient maneuver capability about the trim points. The control vane exhibited linear response characteristics over a large deflection range, with little influence from power, angle of attack or ground proximity in hover. The model induced a positive ground effect in hover that increased as wheel height was approached and strake angle increased.

Falarski, M. D.↗
NASA NTRS1991

Wind tunnel investigation of vortex flows on F/A-18 configuration at subsonic through transonic speed

A wind tunnel experiment was conducted in the David Taylor Research Center 7- by 10-Foot Transonic Tunnel of the wing leading-edge extension (LEX) and forebody vortex flows at subsonic and transonic speeds about a 0.06-scale model of the F/A-18. The primary goal was to improve the understanding and control of the vortical flows, including the phenomena of vortex breakdown and vortex interactions with the vertical tails. Laser vapor screen flow visualizations, LEX, and forebody surface static pressures, and six-component forces and moments were obtained at angles of attack of 10 to 50 degrees, free-stream Mach numbers of 0.20 to 0.90, and Reynolds numbers based on the wing mean aerodynamic chord of 0.96 x 10(exp 6) to 1.75 x 10(exp 6). The wind tunnel results were correlated with in-flight flow visualizations and handling qualities trends obtained by NASA using an F-18 High-Alpha Research Vehicle (HARV) and by the Navy and McDonnell Douglas on F-18 aircraft with LEX fences added to improve the vertical tail buffet environment. Key issues that were addressed include the sensitivity of the vortical flows to the Reynolds number and Mach number; the reduced vertical tail excitation, and the corresponding flow mechanism, in the presence of the LEX fence; the repeatability of data obtained during high angle-of-attack wind tunnel testing of F-18 models; the effects of particle seeding for flow visualization on the quantitative model measurements; and the interpretation of off-body flow visualizations obtained using different illumination and particle seeding techniques.

Erickson, Gary E.↗
NASA NTRS1961

Heat-Transfer Measurements on the Apexes of Two 60 deg Sweptback Delta Wings (Panel Semiapex Angle of 30 deg) Having 0 deg and 45 deg Dihedral at a Mach Number of 4.95

An experimental investigation was conducted to evaluate the heat-transfer rates at the apex of two 60 degree sweptback delta wings (panel semi-apex angle of 30 degrees) having cylindrical leading edges and 0 degrees and 45 degree positive dihedral. The models tested might correspond to the first several feet of a hypersonic reentry vehicle. The tests were conducted at a Mach number of 4.95 and a stagnation temperature of 400 F. nominal test-section unit Reynolds numbers varied from 2 x 10(exp 6) to 12 x 10(exp 6) per foot. The results of the investigation indicated that the laminar heat-transfer distributions (ratio of local to stagnation-line heating rate) about the models normal to the leading edges were in close agreement with two-dimensional blunt-body theory. The three-dimensional stagnation point heat-transfer rate on the 0 degree dihedral model was in excellent agreement with theory and the stagnation-line heat transfer on the straight portion of the leading edge of both models approached a constant level 12 percent above the theoretical stagnation-line level on an isolated swept infinite cylinder. When the heating rates on the 45 degree dihedral model (planform sweep of 69.3 degree) were compared with those on the 0 degree dihedral model (planform sweep of 60 degrees) at equal angles of attack and equal lifts greater than zero, the stagnation-line heating rates on the 45 degrees dihedral model were, in general, considerably lower as a result of the difference in effective sweeps of the leading edges. On the wing panels inboard from the stagnation lines, the differences in heating were very small. The stagnation-line heat-transfer variation with angle of attack, the shift in stagnation-line location, and the reduction in stagnation-line heat transfer resulting from the increase in effective sweep when positive dihedral is incorporated into a constant-panel 0 degree dihedral wing, all agreed with the results of a theoretical study made of highly swept delta wings with large positive dihedral.

Gunn, Charles R.↗
NASA NTRS1987

Wind-tunnel free-flight investigation of a 0.15-scale model of the F-106B airplane with vortex flaps

An investigation to determine the effects of vortex flaps on the flight dynamic characteristics of the F-106B in the area of low-speed, high-angle-of-attack flight was undertaken on a 0.15-scale model of the airplane in the Langley 30- by 60-Foot Tunnel. Static force tests, dynamic forced-oscillation tests, as well as free-flight tests were conducted to obtain a data base on the flight characteristics of the F-106B airplane with vortex flaps. Vortex flap configurations tested included a full-span gothic flap, a full-span constant-chord flap, and a part-span gothic flap.

Yip, Long P.↗
NASA NTRS2017

Computational and Experimental Fluid-Structure Interaction Analysis of a High-Lift Wing with a Slat-Cove Filler for Noise Reduction

Airframe noise is a significant component of overall noise produced by transport aircraft during landing and approach (low speed maneuvers). A significant source for this noise is the cove of the leading-edge slat. The slat-cove filler (SCF) has been shown to be effective at mitigating slat noise. The objective of this work is to understand the fluid-structure interaction (FSI) behavior of a superelastic shape memory alloy (SMA) SCF in flow using both computational and physical models of a high-lift wing. Initial understanding of flow around the SCF and wing is obtained using computational fluid dynamics (CFD) analysis at various angles of attack. A framework compatible with an SMA constitutive model (implemented as a user material subroutine) is used to perform FSI analysis for multiple flow and configuration cases. A scaled physical model of the high-lift wing is constructed and tested in the Texas A&M 3 ft-by-4-foot wind tunnel. Initial validation of both CFD and FSI analysis is conducted by comparing lift, drag and pressure distributions with experimental results.

Scholten, William D.↗
NASA NTRS1993

Investigation of the Vortical Flow Above an F/A-18 Using Doppler Global Velocimetry

The flow above an F/A-18 model, set to 25-degrees angle of attack, was measured using a Doppler global velocimeter, (DGV). The investigation indicated that the complex flow contained many similarities to the vortical flow above a simple delta wing set to a high-angle of attack, including flow standard deviations greater than 30-percent of free- stream. These standard deviation levels were also comparable to results found during a previous investigation of the vortical flow above a YF-17 using fringe-type laser velocimetry. The global measurement capability of the DGV provided the first evidence that the burst vortices above the model were structured. These structures were found to maintain their spatial coherence while the flow varied in an overall sense.

Meyers, James F.↗
NASA NTRS2022

Neurosymbolic Hybrid Approach to Driver Collision Warning

There are two main algorithmic approaches to autonomous driving systems: (1) An end-to-end system in which a single deep neural network learns to map sensory input directly into appropriate warning and driving responses. (2) A mediated hybrid recognition system in which a system is created by combining independent modules that detect each semantic feature. While some researchers believe that deep learning can solve any problem, others believe that a more engineered and symbolic approach is needed to cope with complex environments with less data. Deep learning alone has achieved state-of-the-art results in many areas, from complex gameplay to predicting protein structures. In particular, in image classification and recognition, deep learning models have achieved accuracies as high as humans. But sometimes it can be very difficult to debug if the deep learning model doesn't work. Deep learning models can be vulnerable and are very sensitive to changes in data distribution. Generalization can be problematic. It's usually hard to prove why it works or doesn't. Deep learning models can also be vulnerable to adversarial attacks. Here, we combine deep learning-based object recognition and tracking with an adaptive neurosymbolic network agent, called the Non-Axiomatic Reasoning System (NARS), that can adapt to its environment by building concepts based on perceptual sequences. We achieved an improved intersection-over-union (IOU) object recognition performance of 0.65 in the adaptive retraining model compared to IOU 0.31 in the COCO data pre-trained model. We improved the object detection limits using RADAR sensors in a simulated environment, and demonstrated the weaving car detection capability by combining deep learning-based object detection and tracking with a neurosymbolic model.

Wang, Pei↗
NASA NTRS1999

X-33 (Rev-F) Aeroheating Results of Test 6770 in NASA Langley 20-Inch Mach 6 Air Tunnel

Aeroheating characteristics of the X-33 Rev-F configuration have been experimentally examined in the Langley 20-Inch Mach 6 Air Tunnel (Test 6770). Global surface heat transfer distributions, surface streamline patterns, and shock shapes were measured on a 0.013-scale model at Mach 6 in air. Parametric variations include angles-of-attack of 20-deg, 30-deg, and 40-deg; Reynolds numbers based on model length of 0.9 to 4.9 million; and body-flap deflections of 10-deg and 20-deg. The effects of discrete roughness elements on boundary layer transition, which included trip height, size, and location, both on and off the windward centerline, were investigated. This document is intended to serve as a quick release of preliminary data to the X-33 program; analysis is limited to observations of the experimental trends in order to expedite dissemination.

Berry, Scott A.↗
NASA NTRS2011

Measurement of the Noise Resulting from the Interaction of Turbulence with a Lifting Surface

An experimental study of the noise resulting from the interaction of an airfoil with incident turbulence is presented. The test models include NACA0015 airfoils of different chord lengths, a flat plate with a sharp leading edge, and an airfoil of same section as a reference Fowler flap. The airfoils are immersed in nearly isotropic turbulence. Two approaches for performing the noise measurements are used and compared. The effects that turbulence intensity and scales, airfoil geometry, velocity and angle of attack have on the incident turbulence interaction noise are examined. Detailed directivity measurements are presented. It is found that noise spectral levels beyond the peak frequency decrease more with decreasing airfoil leading edge sharpness, and that spectral peak level (at 0 deg. angle of attack) appears to be mostly controlled by the airfoil fs thickness and chord. Increase in turbulence scale and intensity are observed to lead to a uniform increase of the noise spectral levels with an LI(sup 2) dependence (where L is the turbulence longitudinal integral scale and I is the turbulence intensity). Noise levels are found to scale with the 6th power of velocity and the 2nd power of the airfoil chord. Sensitivity to changes in angle of attack appears to have a turbulence longitudinal integral scale to chord (C) ratio dependence, with large effects on noise for L/C greater than or equal to 1 and decreased effects as L/C becomes smaller than 1. For all L/C values, the directivity pattern of the noise resulting from the incident turbulence is seen to remain symmetric with respect to the direction of the mean flow until stall, at which point, the directivity becomes symmetric with respect to the airfoil chord. It is also observed that sensitivity to angle of attack changes is more pronounced on the model suction side than on the model pressure side, and in the higher frequency range of the spectra for the largest airfoils tested (L/C less than 0.24).

Hutcheson, Florence V.↗
NASA NTRS1990

Ground effects on the low-speed aerodynamics of a powered, generic hypersonic configuration

A study was undertaken in the NASA Langley 14- by 22-foot subsonic tunnel to determine the low-speed aerodynamic characteristics of a powered, generic, hypersonic configuration in ground effect. The model was a simplified configuration consisting of a triangular wedge forebody, a rectangular mid-section which housed the flow through, an ejector type propulsion simulation system, and a rectangular wedge afterbody. Additional model components included a delta wing, a rectangular wedge forebody, inlet fences, exhaust flow deflectors, and afterbody fences. Aerodynamic force and moment data were obtaind over an angle of attack range from -4 to 18 degrees while model height above the tunnel floor was varied from 1/4 inch to 6 feet. Variations in freestream dynamic pressure, from 10 psf to 80 psf, and engine ejector pressure yielded a range of thrust coefficients from 0 to 0.8.

Gatlin, Gregory M.↗
NASA NTRS1963

Aeroelastic Tests of an Eight Percent Scale Saturn C-1 Block II

Buffet and flutter characteristics of Saturn Apollo mission were studied using a dynamically scaled model. The model was built around a central aluminum tube for scaled stiffness distribution and strength to resist loads imposed during testing. Styrofoam sections attached to the core provided the correct external contours. Lead weights were added for correct mass distribution. An electromagnetic shaker was used to excite the model in its flexible modes of vibration during portions of the test. The model was supported on a sting, mounted by leaf springs, cables and torsion bars. The support system provided for simulating the full scale rigid body pitch frequency with minimum restraint imposed on elastic deflections. Bending moments recorded by sensors on the aluminum tube. Several modified nose configurations were tested: The basic configuration was tested with and without a flow separator disk on the escape rocket motor, tests also were made with the escape tower and rocket motor removed completely. For the final test, the Apollo capsule was replaced with a Jupiter nose cone. The test program consisted of determining model response throughout the transonic speed range at angles of attack up to 6 degrees and measuring the aerodynamic damping over the same range for the basic model and the modified configurations. Signals from the model pickup were recorded on tape for later analysis. The data obtained were used to estimate bending moments that would be produced on the full-scale vehicle by aerodynamic forces due to buffeting.

EXPERIMENTS↗
NASA NTRS1989

Low speed wind tunnel investigation of the flow about delta wing, oscillating in pitch to very high angle of attack

Six-component airload histories were obtained for models of aspect ratio 1, 1.5, and 2. Examples are given from data obtained over a range of 'reduced frequency' parameters from 0.01 to 0.08. They include the unsteady response of the leading-edge vortices, as evidenced both by the time-dependent airloads and motion pictures of smoke released from the leading edge and illuminated by a thin sheet of laser light.

Jarrah, Mohammad-Ameen M.↗
NASA NTRS2001

Prediction of Unsteady Aerodynamic Coefficients at High Angles of Attack

The nonlinear indicial response method is used to model the unsteady aerodynamic coefficients in the low speed longitudinal oscillatory wind tunnel test data of the 0.1 scale model of the F-16XL aircraft. Exponential functions are used to approximate the deficiency function in the indicial response. Using one set of oscillatory wind tunnel data and parameter identification method, the unknown parameters in the exponential functions are estimated. The genetic algorithm is used as a least square minimizing algorithm. The assumed model structures and parameter estimates are validated by comparing the predictions with other sets of available oscillatory wind tunnel test data.

Pamadi, Bandu N.↗