Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “amplifier”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Broadband spectral combining of three pulse-shaped fiber amplifiers with 42fs compressed pulse duration

We demonstrate ultra-broadband spectral combining of ultrashort pulses from Yb-doped fiber amplifiers, with coherently spectrally synthesized pulse shaping, to achieve tens-of-fs pulses. This method can fully compensate for gain narrowing and high order dispersion over broad bandwidth. We produce 42fs pulses by spectrally synthesizing three chirped-pulse fiber amplifiers and two programmable pulse shapers across an 80nm overall bandwidth. To the best of our knowledge, this is the shortest pulse duration achieved from a spectrally combined fiber system at one-micron wavelength. This work provides a path toward high-energy, tens-of-fs fiber chirped-pulse amplification systems.

43 PARTICLE ACCELERATORS↗

Self-phase modulation compensation in a regenerative amplifier using cascaded second-order nonlinearities

Self-phase modulation limits the amplification of short optical pulses because of spatial self-focusing and spectral broadening. Cascaded nonlinearities are theoretically and experimentally investigated for intracavity nonlinearity compensation in a neodymium-doped yttrium-lithium-fluoride (Nd:YLF) regenerative amplifier. Experimental results are in good agreement with simulations. Spectral broadening is significantly reduced, allowing for efficient amplification in a Nd:YLF power amplifier.

Dorrer, C.↗

Demonstration of a side-pumped cross-seeded thin-slab pre-amplifier for high-power Ti:Sa laser systems

Here, we demonstrate a room-temperature Ti:Sapphire (Ti:Sa) amplifier that uses a cross pump-seed geometry (cross-thin-slab) to generate 30-mJ output pulses at 0.5-kHz repetition rate, and 25 mJ at 1 kHz when pumped by 100-mJ, 515-nm pulses from a diode-pumped Yb:YAG laser. The geometry allows to maintain a crystal temperature of ~30°C using cooling water at 10°C. The amplifier is an attractive solution for use in the first stages of amplification in high peak and high average power chirped pulse amplification laser systems.

47 OTHER INSTRUMENTATION↗

1.2-kW all-fiber Yb-doped multicore fiber amplifier

Here we have demonstrated a record-high 1.2 kW, all-fiber multicore amplifier using a six-core single-mode Yb-doped fiber and a multicore pump-signal combiner (PSC). The output power is limited by the pump power of 1.9 kW. We have developed double-clad six-core fibers and PSCs for this demonstration. Each of the six Yb-doped cores has a 17-µm mode-field diameter (MFD) with a trench index profile and is capable of kW-class operation. The potential power scaling to the 10-kW level in a single amplifier with high brightness should be feasible with advanced thermal management and coherent beam combination.

42 ENGINEERING↗

High-efficiency, single-stage tunable optical parametric amplifier for visible photocathode applications

In this work we present a single-stage optical parametric amplifier (OPA) with an average conversion efficiency up to 38%, tunable between 1.01 and 1.18 µm. The OPA seed is produced by a gain-managed nonlinear fiber amplifier. Numerical modeling of the seed pulse generation shows a linear chirp, a smoothly broadened redshifted spectrum, and a high spectral energy density. When up-converted to the visible through second-harmonic generation, the signal pulses are suitable for visible photocathode excitation.

14 SOLAR ENERGY↗

TEAMER: Drifting Hydrophone System - Block Diagram and Pre-Amplifier Calibrations

This data release is part of TEAMER RFTS 2, where the Cooperative Institute for Marine Resources Studies (CIMRS) at Oregon State University is performing hardware and software development and integration of four newly designed drifting hydrophone systems for underwater noise measurements at marine renewable energy projects. These new acoustic systems will provide advanced technology support available for use at both tidal and wave energy deployments adding additional resources to the limited amount of drifting hydrophone technologies that are available to the marine energy community The submission data contains 2 files plus a Post-Access Report: One file containing the calibration parameters for four (4) pre-amplifier boards used on the drifting hydrophones. Pre-amplifier boards are model "WB PREAMP REV6," with serial numbers; 28, 29, 30, and 31. One image file illustrating the system functional block diagram of the drifting hydrophone system configuration.

16 TIDAL AND WAVE POWER↗

Modeling of the amplified optical stochastic cooling experiment at IOTA

Optical Stochastic Cooling (OSC), a beam cooling technique based on Stochastic Cooling, is in the early stages of experimental development. It uses radiation produced by the beam in an undulator magnet (the pickup) to correct the momentum deviation of particles downstream in another undulator (the kicker). The OSC mechanism was recently demonstrated at Fermilab’s IOTA ring using a passive configuration. However, the cooling rate of OSC can be dramatically increased by first amplifying the undulator radiation before applying the corrective kick. In collaboration with the IOTA experiment, we developed a computational model of the OSC mechanism. This paper presents beam-dynamics simulations of the amplified-OSC configuration. We implement a model of intrabeam scattering and study the effects on beam equilibrium and diffusion rate as a function of bunch charge. Finally, we investigate the phase-space dynamics with various coupling configurations between the transverse and longitudinal planes.

43 PARTICLE ACCELERATORS↗

Performance of a Combined System Using an X-Ray FEL Oscillator and a High-Gain FEL Amplifier

The LCLS-II at SLAC will feature a 4 GeV CW superconducting (SC) RF linac [1] that can potentially drive a 5th harmonic X-Ray FEL Oscillator (XFELO) to produce fully coherent, 1 MW photon pulses with a 5 meV bandwidth at 14.4 keV [2]. The XFELO output can serve as the input seed signal for a high-gain FEL amplifier employing fs electron beams from the normal conducting SLAC linac, thereby generating coherent, fs x-ray pulses with TW peak powers using a tapered undulator after saturation [3]. Coherent, intense output at several tens of keV will also be feasible if one considers a harmonic generation scheme. Thus, one can potentially reach the 42 keV photon energy required for the MaRIE project [4] by beginning with an XFELO operating at the 3rd harmonic to produce 14.0 keV photons using a 12 GeV SCRF linac, and then subsequently using the high-gain harmonic generation scheme to generate and amplify the 3th harmonic at 42 keV [5]. We report extensive GINGER simulations that determine an optimized parameter set for the combined system.

Gupta, L.↗

Direct Probe Mounted High-Performance Amplifiers for Pulsed Measurement

High electrical noise and short time scales of pulsed magnets create significant challenges for electrical measurements, particularly in the sub-MHz frequency window, where bulk of the transport measurements is routinely conducted. The proper design of the first stage of signal conditioning and amplification is the critical step in increasing sensitivity of the measurements in such a harsh environment. We developed a custom instrumentation amplifier to implement a number of noise-reducing features for pulsed field measurements. The amplifier utilizes single-chip design based on recently released AD8421 [1]. The preamp design has proven to be successful and is now being implemented on a variety of probes. The design is continuously being revised and updated as better preamp chips become available.

36 MATERIALS SCIENCE↗

The Physics of Gain Mechanisms in a Self-Amplified Spontaneous Emission Free-Electron Laser

This is the final report for the DoE BES contract DE-FG02-07ER46272. This grant began under a title that gives its history in a few words: The Physics of Gain Mechanisms in a Self-Amplified Spontaneous Emission Free-Electron Laser. At the time of adopting this name, the UCLA Particle Beam Physics Laboratory (PBPL) was at the forefront of the first demonstrations of SASE FEL, giving the experimental basis for the 4th generation X-ray light source now exemplified by the LCLS, a remarkable generation of machines that have revolutionize nanoscale and ultrafast science. The grant title indicates that physical aspects of the FEL are of interest, and implies that progress requires comprehensive investigations. These aspects include: the physics and technology of high brightness electron beam generation, phase space manipulations, advanced beam diagnostics, state-of-the-art undulators, studies of FEL mode characteristics, as well as the introduction of new theoretical models and start-to-end simulations, all yielding a deep understanding of the SASE FEL. The latest period (2010-13) of BES grant support has been the most productive yet for the UCLA PBPL, and the extensive list of accomplishments is illustrative of our central contributions to advanced FEL research. We give a concise overview here and review our research results in further detail below. In FEL and ultrafast beam physics, we have experimentally investigated: production of helical beams and FEL modes with orbital angular momentum; chirp-taper single-spike FEL gain; new FROG techniques optimized for FEL, introduced coherent imaging of beam profiles using transition radiation; and demonstrated a next generation cryoundulator. We have performed deep theoretical studies of these phenomena and other advanced FEL physics concepts, such as the space-charge amplifier. In high brightness beams, we have: introduced a new class of hybrid photoinjector for <100 fs beam production; developed new approaches to self-shaped ellipsoidal beams; used nonlinear plasma oscillations to create beam pulse trains; tested new plasmonic, high quantum efficiency cathodes, and developed new methods of beam measurement with um spatial/sub-fs temporal resolution. In ultrafast imaging, we have: developed advanced electro-optic timing systems, performed the 1st pump-probe study using single shot UED, demonstrated continuously time-resolved UED with RF deflection; made initial use of inverse Compton scattering (ICS) X-ray sources in application through single-shot inline phase contrast imaging, established single-shot X-ray diffraction, and observed ICS high harmonic generation and redshifting due to nonlinear effects. In 5th generation light source research, we have developed the techniques of narrowband, very high power coherent Cerenkov radiation sources based on dielectric wakefield devices. This work is represented by numerous publications in leading journals: e.g. Nature Physics, Physical Review Letters, Applied Physics Letters. The PBPL program’s influence on the field also extends to organization of the electron beam applications community; we have organized the first international UED workshops and the initial two meetings dedicated to 5th generation light source.

43 PARTICLE ACCELERATORS↗

Compact Ultraintense Femtosecond Laser via Raman Amplifier and Compressor in Plasma

The main objective of this project was to conduct experimental and theoretical research to find conditions leading to higher, than previously obtained efficiency η of transfer the pump energy into the short seed beam in plasma of Stimulated Raman Back-Scattering (SRBS). We have demonstrated very large amplification and compression in our earlier SRBS plasma. However, the efficiency η was much too low to reach very high intensity of the output beam in the focal spot. Recently, by solving a very difficult technical SRBS’ problem, namely, the creation of very reproducible and much larger diameter plasma channels than in our earlier research, we propose a new approach to obtain higher efficiency η. The crucial new result was a very reproducible, low noise amplified seed in the larger diameter of the plasma channel leading to the higher efficiency. Using this new setup and very encouraging results about increase efficiency continuing this approach in the future the efficiency is expect to reach the range of η ≈15 - 20 % required to develop practical SRBS plasma laser. Intellectual Merit: The model for the present project was created by our earlier SRBS experiments. The main objective of those experiments was to amplify and compress the seed pulses in a plasma . The experiments demonstrated an unprecedented large pulse intensity amplification of 20,000 in system of 2-passes in ~2mm long plasma, and the seed pulse compression from 550fsec down to ~50fsec. The pump and seed beams in the present project have diameters of ~0.2–0.25mm each, propagating in ~0.35 - 0.45mm diameter and ~2-2.5mm long plasma channels (optimal length for our SRBS experiment) with input pump and seed intensities of 2x1014 and 3x1013 W/cm2, respectively. Such an SRBS system design was “prescribed” by computer simulations, which predict elimination of the SRBS “ saturation” for a such relatively short plasma channel. Plasma channels has been created by combining shorter (200psec) and longer (5nsec) laser pulses using an axicon lens for shorter pulse and spherical lens for longer pulse, a unique procedure we have developed for SRBS experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fiber Based Optical Amplifier for High Energy Laser Pulses Final Report CRADA No. TC02100.0

This was a collaborative effort between Lawrence Livermore National Security, LLC (formerly The Regents of the University of California)/Lawrence Livermore National Laboratory (LLNL), and The Boeing Company to develop an optical fiber-based laser amplifier capable of producing and sustaining very high-energy, nanosecond-scale optical pulses. The overall technical objective of this CRADA was to research, design, and develop an optical fiber-based amplifier that would meet specific metrics.

42 ENGINEERING↗

Development of a Regenerative Amplifier for the Coherent electron Cooling Proof of Principle Experiment (CeC-PoP) at RHIC

The commercial laser from NuPhoton that was used for the Coherent-electron-Cooling Proof of Principle (CeC-PoP) experiment in the past runs could not meet the tight specifications needed to demonstrate coherent electron cooling due to nonlinear effects inherent to fiber lasers operating at high pulse peak powers. To overcome these limitations, the Laser design was modified prior to the start of the 2018 RHIC run by introducing an additional amplifier stage that allows to take over the majority of the amplification process from the fiber amplifiers to keep the peak power in the fibers low and avoid the accumulation of nonlinear effects. This approach allows for a reduction of the output power of the NuPhoton laser to about 5% of the nominal power level avoiding the accumulation of nonlinear effect and leaving 6mW of unstable IR seed power (See Figure 2) for a subsequent amplification stage.

43 PARTICLE ACCELERATORS↗

LANL-Amplifier [Slides]

Slides show borrowed amplifier in use (working) and E-1 amplifier not in use (not working) to be sent to The Modal Shop for connection inspection.

42 ENGINEERING↗

Tunable Laser-Plasma Amplifier (Final Report)

Exploration at the laser intensity frontier has always offered new avenues for physics and reaching beyond this frontier is a grand challenge. Present-day petawatt-class lasers provide focused intensities on target of 10 22 W/cm 2 , corresponding to electric fields of 200 TV/m, while laser-plasma amplification opens a route for focused intensities well above 10 23 W/cm 2 . Intensities in this range provide the ability to test quantum electrodynamics in the unexplored low-energy, strong-field regime where signatures for new physics may arise. The behavior of matter under such extraordinary conditions is a rich and fascinating subject, not only in its own right in fundamental plasma physics, but for the many potential applications that promise to enrich the natural sciences in the future, including compact electron-beam, ion-beam particle accelerators, and ultra-bright X-ray sources. Although laser systems are now under construction internationally to access intensities of 10 23 W/cm 2 , the current technologies used appear to be fundamentally limited to these intensities. The realization of intensities beyond 10 23 W/cm 2 using parametric amplification in plasmas promises a breakthrough in high-energy density physics. Parametric amplification using Raman scattering in a plasma could provide the enabling technology for the generation of ultra-high-power laser pulses, but a more complete understanding of the nonlinear optics of plasmas is required. There is a significant gap in well-diagnosed laser-plasma instability studies of nonlinear plasma-wave phenomena, which are critical to understand for future laser-plasma devices. To achieve an efficient laser-plasma amplifier, plasma waves must be driven to large amplitude where significant energy can be rapidly transferred from the pump to the seed over the pulse duration of the seed. Simulations suggest that this nonlinear pump depletion regime can be achieved in the “pi-pulse” amplification regime. While simulations show this optimal regime with efficient amplification, it has remained elusive in experiments and there is a growing consensus within the community that thermal effects and pump beam limitations prevent laser-plasma amplifiers from progressing through the linear regime into the nonlinear pump depletion regime. Previous experiments have been significantly limited by the laser power available at the necessary wavelengths for the seed laser; therefore, the amplification is required to start in the linear regime where it is sensitive to many deleterious effects. The enabling technology (currently unique to plasma-wave amplification in the world) at the University of Rochester is the ability to provide a seed pulse with sufficient power (4 mJ/100 fs seed) to immediately drive nonlinear plasma waves into the pi-pulse regime and to tune its wavelength to optimize the efficiency of energy transfer. This in combination with the state-of-the-art OMEGA heater beams providing multiple kilojoules in a nanosecond to sufficiently heat the plasma make this system distinct from previous studies. These heater beams will provide, for the first time in Raman amplification studies, a homogeneous electron temperature high enough to prevent pump beam propagation issues that have plagued previous experiments. These systems will provide a platform for driving electron-plasma waves into the nonlinear regime where pump depletion and pulse shortening are predicted to lead to high amplification efficiencies (>30%). The Team has made significant progress through prior support from DOE Fusion Energy Sciences [DOE Office of Science Award Number DE-SC0016253 (2016-2022)]. This includes twenty-two peer-reviewed manuscripts, one patent, ten contributed talks presented at international conferences, and research that was highlighted as invited talks at fifteen international conferences. The broader impacts of this research are evident in the support of early career scientists, two Ph.D. theses, four current graduate students, a Masters Project, two undergraduate researchers, and an underrepresented minority student hired through the California Alliance for Minority Participation who now works as a Research Engineer in the group. This research met all of the funded research objectives and the highlights from primary Raman amplification thrust of this work are discussed below and form the foundation for the proposed research.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

First Results from the KMOS Lens-Amplified Spectroscopic Survey (KLASS): Kinematics of Lensed Galaxies at Cosmic Noon

We present the first results of the K-band Multi-Object Spectrometer (KMOS) Lens-Amplified Spectroscopic Survey, a new ESO Very Large Telescope large program, doing multi-object integral field spectroscopy of galaxies gravitationally lensed behind seven galaxy clusters selected from the Hubble Space Telescope (HST) Grism Lens-Amplified Survey from Space. Using the power of the cluster magnification, we are able to reveal the kinematic structure of 25 galaxies at 0.7≲z≲2.3, in four cluster fields, with stellar masses 7.8≲log(M{sub ⋆}/ M{sub ⊙})≲10.5. This sample includes five sources at z>1 with lower stellar masses than in any previous kinematic integral field unit (IFU) surveys. Our sample displays a diversity in kinematic structure over this mass and redshift range. The majority of our kinematically resolved sample is rotationally supported, but with a lower ratio of rotational velocity to velocity dispersion than in the local universe, indicating the fraction of dynamically hot disks changes with cosmic time. We find that no galaxies with stellar mass <3×10{sup 9} M{sub ⊙} in our sample display regular ordered rotation. Using the enhanced spatial resolution from lensing, we resolve a lower number of dispersion-dominated systems compared to field surveys, competitive with findings from surveys using adaptive optics. We find that the KMOS IFUs recover emission line flux from HST grism-selected objects more faithfully than slit spectrographs. With artificial slits, we estimate that slit spectrographs miss, on average, 60% of the total flux of emission lines, which decreases rapidly if the emission line is spatially offset from the continuum.

79 ASTRONOMY AND ASTROPHYSICS↗

Field-effect transistor improves electrometer amplifier

An electrometer amplifier uses a field effect transistor to measure currents of low amperage. The circuit, developed as an ac amplifier, is used with an external filter which limits bandwidth to achieve optimum noise performance.

Munoz, R.↗

Tiny biomedical amplifier combines high performance, low power drain

Transistorized, portable, high performance amplifier with low power drain facilitates biomedical studies on mobile subjects. This device, which utilizes a differential input to obtain a common-mode rejection, is used for amplifying electrocardiogram and electromyogram signals.

Deboo, G. J.↗