Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transient Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Eigenvalue/Eigenvector derivatives for SAVI Gimbalflex nonlinear transient response analysis

An eigenvector expansion method is utilized to predict eigenvalue and eigenvector derivatives due to geometric reconfiguration of a Gimbalflex fine-pointing/vibration isolation system called SAVI (Space Active Vibration Isolation). The eigenvector expansion method used is a modification of the classical method and allows for rigid body roots. Using the resulting modal derivatives, free-free nonlinear equations of motion are developed with Lagrange's Method. These equations represent a nonlinear plant model to be used in conjunction with a control system transient response simulation.

Orr, M. F., Jr.↗

Phase change energy storage for solar dynamic power systems

This paper presents the results of a transient computer simulation that was developed to study phase change energy storage techniques for Space Station Freedom (SSF) solar dynamic (SD) power systems. Such SD systems may be used in future growth SSF configurations. Two solar dynamic options are considered in this paper: Brayton and Rankine. Model elements consist of a single node receiver and concentrator, and takes into account overall heat engine efficiency and power distribution characteristics. The simulation not only computes the energy stored in the receiver phase change material (PCM), but also the amount of the PCM required for various combinations of load demands and power system mission constraints. For a solar dynamic power system in low earth orbit, the amount of stored PCM energy is calculated by balancing the solar energy input and the energy consumed by the loads corrected by an overall system efficiency. The model assumes an average 75 kW SD power system load profile which is connected to user loads via dedicated power distribution channels. The model then calculates the stored energy in the receiver and subsequently estimates the quantity of PCM necessary to meet peaking and contingency requirements. The model can also be used to conduct trade studies on the performance of SD power systems using different storage materials.

Chiaramonte, F. P.↗

Parallel Visualization Co-Processing of Overnight CFD Propulsion Applications

An interactive visualization system pV3 is being developed for the investigation of advanced computational methodologies employing visualization and parallel processing for the extraction of information contained in large-scale transient engineering simulations. Visual techniques for extracting information from the data in terms of cutting planes, iso-surfaces, particle tracing and vector fields are included in this system. This paper discusses improvements to the pV3 system developed under NASA's Affordable High Performance Computing project.

Edwards, David E.↗

Cryogenic Fuel Tank Draining Analysis Model

One of the technological challenges in designing advanced hypersonic aircraft and the next generation of spacecraft is developing reusable flight-weight cryogenic fuel tanks. As an aid in the design and analysis of these cryogenic tanks, a computational fluid dynamics (CFD) model has been developed specifically for the analysis of flow in a cryogenic fuel tank. This model employs the full set of Navier-Stokes equations, except that viscous dissipation is neglected in the energy equation. An explicit finite difference technique in two-dimensional generalized coordinates, approximated to second-order accuracy in both space and time is used. The stiffness resulting from the low Mach number is resolved by using artificial compressibility. The model simulates the transient, two-dimensional draining of a fuel tank cross section. To calculate the slosh wave dynamics the interface between the ullage gas and liquid fuel is modeled as a free surface. Then, experimental data for free convection inside a horizontal cylinder are compared with model results. Finally, cryogenic tank draining calculations are performed with three different wall heat fluxes to demonstrate the effect of wall heat flux on the internal tank flow field.

Greer, Donald↗

Status of The SPARC-GRIPS Initiative

The GCM-Reality Intercomparison Project for the Symbolic Processing Algorithmic Research Computer (SPARC) is an initiative designed to provide a comprehensive assessment of our ability to model the present-day climate and the impacts of different physical perturbations. This poster will show the different scientific experiments being conducted in the general purpose rocket instrumentation and payload system (GRIPS) and include some summaries of the results. The three concurrent aspects of GRIPS are: (1) studies of the climate and transient features simulated by the models; (2) examinations of different parametrizations and their impacts on the model climate; (3) studies of the impact of physical perturbations, such as solar forcing, volcanic aerosols and ozone change. Sample results from a number of these areas will be presented, with discussion of their implications for our ability to model the climate of the present and future atmosphere.

Pawson, Steven↗

PDE Nozzle Optimization Using a Genetic Algorithm

Genetic algorithms, which simulate evolution in natural systems, have been used to find solutions to optimization problems that seem intractable to standard approaches. In this study, the feasibility of using a GA to find an optimum, fixed profile nozzle for a pulse detonation engine (PDE) is demonstrated. The objective was to maximize impulse during the detonation wave passage and blow-down phases of operation. Impulse of each profile variant was obtained by using the CFD code Mozart/2.0 to simulate the transient flow. After 7 generations, the method has identified a nozzle profile that certainly is a candidate for optimum solution. The constraints on the generality of this possible solution remain to be clarified.

Billings, Dana↗

Solving Problems With SINDA/FLUINT

SINDA/FLUINT, the NASA standard software system for thermohydraulic analysis, provides computational simulation of interacting thermal and fluid effects in designs modeled as heat transfer and fluid flow networks. The product saves time and money by making the user's design process faster and easier, and allowing the user to gain a better understanding of complex systems. The code is completely extensible, allowing the user to choose the features, accuracy and approximation levels, and outputs. Users can also add their own customizations as needed to handle unique design tasks or to automate repetitive tasks. Applications for SINDA/FLUINT include the pharmaceutical, petrochemical, biomedical, electronics, and energy industries. The system has been used to simulate nuclear reactors, windshield wipers, and human windpipes. In the automotive industry, it simulates the transient liquid/vapor flows within air conditioning systems.

Source record↗

Simulations of Instabilities in Complex Valve and Feed Systems

CFD analyses are playing an increasingly important role in identifying and characterizing flow induced instabilities in rocket engine test facilities and flight systems. In this paper, we analyze instability mechanisms that range from turbulent pressure fluctuations due to vortex shedding in structurally complex valve systems to flow resonance in plug cavities to large scale pressure fluctuations due to collapse of cavitation induced vapor clouds. Furthermore, we discuss simulations of transient behavior related to valve motion that can serve as guidelines for valve scheduling. Such predictions of valve response to varying flow conditions is of crucial importance to engine operation and testing.

Ahuja, Vineet↗

Compartment Venting Analyses of Ares I First Stage Systems Tunnel

Compartment venting analyses have been performed for the Ares I first stage systems tunnel using both the lumped parameter method and the three-dimensional (31)) transient computational fluid dynamics (CFD) approach. The main objective of venting analyses is to predict the magnitudes of differential pressures across the skin so the integrity of solid walls can be evaluated and properly designed. The lumped parameter method assumes the gas pressure and temperature inside the systems tunnel are spatially uniform, which is questionable since the tunnel is about 1,700 in. long and 4 in. wide. Therefore, 31) transient CFD simulations using the commercial CFD code FLUENT are performed in order to examine the gas pressure and temperature variations inside the tunnel. It was found that the uniform pressure and temperature assumptions inside the systems tunnel are valid during ascent. During reentry, the uniform pressure assumption is also reasonable but the uniform temperature assumption is not valid. Predicted pressure and temperature inside the systems tunnel using CFD are also compared with those from the lumped parameter method using the NASA code CHCHVENT. In general, the average pressure and temperature inside the systems tunnel from CFD are between the burst and crush results from CHCHVENT during both ascent and reentry. The skin differential pressure and pressure inside the systems tunnel relative to freestream pressure from CHCHVENT as well as velocity vectors and streamlines are also discussed in detail.

Wang, Qunzhen↗

Comparison of Analysis, Simulation, and Measurement of Wire-to-Wire Crosstalk

In this investigation, we compare crosstalk analysis, simulation, and measurement results for electrically short configurations. Methods include hand calculations, PSPICE simulations, Microstripes transient field solver, and empirical measurement. In total, four representative physical configurations are examined, including a single wire over a ground plane, a twisted pair over a ground plane, generator plus receptor wires inside a cylindrical conduit, and a single receptor wire inside a cylindrical conduit. Part 1 addresses the first two cases, and Part 2 addresses the final two. Agreement between the analysis methods and test data is shown to be very good.

Bradley, Arthur T.↗

Future Changes in Major Stratospheric Warmings in CCMI Models

Major stratospheric warmings (MSWs) are one of the most important phenomena of wintertime Arctic stratospheric variability. They consist of a warming of the Arctic stratosphere and a deceleration of the polar night jet, triggered by an anomalously high injection of tropospheric wave activity into the stratosphere. Due to the relevance and the impact of MSWs on the tropospheric circulation, several model studies have investigated their potential responses to climate change. However, a wide range of results has been obtained, extending from a future increase in the frequency of MSWs to a decrease. These discrepancies might be explained by different factors such as a competition of radiative and dynamical contributors with opposite effects on the Arctic polar vortex, biases of models to reproduce the related processes, or the metric chosen for the identification of MSWs. In this study, future changes in wintertime Arctic stratospheric variability are examined in order to obtaina more precise picture of future changes in the occurrence of MSWs. In particular, transient REFC2 simulations of different CCMs involved in the Chemistry Climate Model Initiative (CCMI) are used. These simulations extend from 1960 to 2100 and include forcings by halogens and greenhouse gases following the specifications of the CCMI-REF-C2 scenario. Sea surface temperatures (SSTs) and sea-ice distributions are either prescribed from coupled climate model integrations or calculated internally in the case of fully coupled atmosphere-ocean CCMs. Potential changes in the frequency and main characteristics of MSWs in the future are investigated with special focus on the dependence of the results on the criterion for the identification of MSWs and the tropospheric forcing of these phenomena.

Chemistry-Climate Modeling↗

The Response of the Ozone Layer Under Abrupt 4xCO2 in CMIP6

Previous studies indicate a possible role of stratospheric ozone chemistry feedbacks in the climate response to 4xCO2, either via a reduction in equilibrium climate sensitivity (ECS) (Nowack et al., 2015), or via changes in the tropospheric circulation (Chiodo and Polvani, 2017). However, these effects are subject to uncertainty. Part of the uncertainty may stem from the dependency of the feedback on the pattern of the ozone response, as the radiative efficiency of ozone largely depends on its vertical distribution (Lacis et al., 1990). Here, an analysis is presented of the ozone layer response to 4xCO2 in chemistry–climate models (CCMs) which participated to CMIP intercomparisons. In a previous study using CMIP5 models, it has been shown that under 4xCO2, ozone decreases in the tropical lower stratosphere, and increases over the high latitudes and throughout the upper stratosphere. It was also found that a substantial portion of the spread in the tropical column ozone is tied to inter-model spread in tropical upwelling, which is in turn partly tied to ECS (Chiodo et al., 2018). Here, we revisit this connection using4xCO2 data from CMIP6, thereby exploiting the larger number of CCMs than in CMIP5. In addition, we explore the linearity of the ozone response, by complementing the analysis with simulations using transient CO2 forcing (1pc/year). We show that the pattern of the ozone response in is similar to CMIP5. In some models (e.g. WACCM), we find larger ozone responses in CMIP6 than in CMIP5, partly because of the larger ECS and thus larger upwelling response in the tropical pipe. In this presentation, we will discuss the relationship between radiative forcing, transport and ozone, as well as further implications for CMIP6 models.

Ozone layer↗

Aeroacoustic Optimization of Installed Propeller Configurations with Scattering and Shielding Effects

An optimization capability is developed for acoustic scattering and shielding of installed propellers and rotors, based on a spacetime Galerkin time domain boundary element method (TDBEM). The time domain approach is particularly suitable for efficient simulation of transient, rotating, and broadband noise sources such as propellers. The use of algorithmic differentiation allows efficient evaluation of design sensitivities required for gradient-based design optimization with a large number of design variables. We present a validation exercise for the coherent broadband scattering capability against an analytical solution, showing excellent agreement. We then demonstrate the optimization tool on a series of inverse design cases with broadband and rotating sources, as well as an optimization problem for a propeller-wing configuration. The results show good performance for optimization problems with the characteristics of realistic installed propeller configurations.

Maks J Groom↗

Aeroacoustic Optimization of Installed Propeller Configurations with Scattering and Shielding Effects

An optimization capability is developed for acoustic scattering and shielding of installed propellers and rotors, based on a spacetime Galerkin time domain boundary element method (TDBEM). The time domain approach is particularly suitable for efficient simulation of transient, rotating, and broadband noise sources such as propellers. The use of algorithmic differentiation allows efficient evaluation of design sensitivities required for gradient-based design optimization with a large number of design variables. We present a validation exercise for the coherent broadband scattering capability against an analytical solution, showing excellent agreement. We then demonstrate the optimization tool on a series of inverse design cases with broadband and rotating sources, as well as an optimization problem for a propeller-wing configuration. The results show good performance for optimization problems with the characteristics of realistic installed propeller configurations.

Maks J Groom↗

Design and Use of a Penetrating Deposition Nozzle for Z-Pinning Additive Manufacturing

Fused Filament Fabrication (FFF) involves depositing material layer-by-layer to create athree-dimensional object. This method often demonstrates high mechanical anisotropy in theprinted structure, leading to a drop in the material strength of the part when comparing structuresalong the deposition plane (X/Y-Axis) versus across layers in the build direction (Z-Axis). Initialefforts to improve anisotropy led to the development of the Z-Pinning process, where continuouspins are deposited across layers in the Z-Axis. Z-pinning has demonstrated significant gains intoughness and inter-layer strength, particularly in fiber-reinforced materials. However, thisprocess can also create flaws in the structure that increase in severity and frequency as the pinsgrow in length and diameter. To mitigate this, a penetrating nozzle has been developed thatextends a fine-tipped extrusion nozzle deep into the pin cavity and simultaneously extrudesmaterial as it retracts. This study investigates the printability of the penetrating nozzle for simplegeometries and evaluates the resulting Z-pinning mesostructure. As a result of this study, theprototype penetrating nozzle design was analyzed and built. Through a pressure driven flowanalysis it was determined that the penetrating nozzle extruder can not only flow extrudefilament. After a transient thermal simulation it was found that after a pause of 15 secondsresume printing with no drop in heat at nozzle exit.

Bales, Brenin↗

Resilient Inverter-Driven Black Start with Collective Parallel Grid-Forming Operation: Preprint

As the modern power systems are experiencing exceptional changes with increasing penetration of inverter-based resources (IBRs), system restoration using IBRs has received attention. Using local grid-forming (GFM) assets near consumers, engineered to establish grid voltages in the absence of a stiff grid, i.e., bottom-up restoration, a distribution system would obtain high system resilience, by not relying on the bulk power system restoration requiring significant human intervention and procedure to restore. This paper studies the technical feasibility of the novel approach with detailed electromagnetic transient (EMT) simulations. To thoroughly evaluate the potential of GFM inverters and technical challenges in IBR-driven black start, a detailed three-phase inverter model is developed, including negative-sequence control for voltage balance and a phase-by-phase current limiter to sustain momentary overloading during the black start. To examine dynamic aspects of the black start process, the EMT simulation also models transformer and motor dynamics to emulate their inrush and start-up behaviors as well as network dynamics. In addition, active involvement of grid-following distributed energy resources (DER) is also studied to facilitate the black start process. It is shown that, by allowing multiple GFM inverters to collectively black start without master-slave coordination, a system can achieve high resilience even with a fraction of assets lost. Two test cases of inverter-driven black start using two and one GFM inverters, respectively, for a heavily unbalanced 2-MVA distribution feeder are demonstrated. Takeaways for further study and field deployment are provided.

grid-forming inverter↗