Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thermal performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Spray Manufacturing Thermal Insulation Composites

Cellulose-based thermal insulation materials present significant potential for modern green building applications due to their inherent carbon sequestration properties. However, traditional manufacturing of composites often results in the limited thermal insulation performance and embodied carbon footprint due to an increased density from material shrinkage and higher energy consumption during the water-based slurry drying process. Here, we report solvent spraying coupled with dry powder feedstock to manufacture highly porous silica/straw insulation composites. The manufactured composite exhibits negligible shrinkage with the density of 0.08 g/cm 3 , thermal conductivity of 27.8 mW/(m·K), flexural modulus of 3.1 MPa, and compressive modulus of 0.89 MPa. Additionally, the prepared composite demonstrates fire retardancy (burning rate of 0.5 mm/min) and recyclability (99%). Furthermore, this solvent-spraying strategy opens up opportunities of energy-efficient insulation materials for carbon-sequestration building sectors.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Characterization of high-temperature figure of merit for solar-thermal absorbers

The figure of merit (FOM) is a widely used metric to characterize the solar-thermal conversion performance of solar absorber layers. Many of previous works have reported FOMs estimated from the radiative properties measured at room temperature. However, advanced concentrated solar power (CSP) plants operate at very high temperatures (~750°C), which can strongly affect the absorber’s radiative properties. Here, the present work proposes using a 1-D conduction-based reference bar technique to directly measure the converted thermal energy to determine the FOM at high absorber temperatures (≳ 750°C) while operating under a large solar concentration (~ 1200 x suns). Using the finite difference method, we carefully analyze several key parameters influencing the design of the experimental setup, such as temperature distribution, material properties, heat loss, and sensor accuracy. In addition, a rigorous uncertainty analysis is incorporated into the FOM to ascertain the confidence level of the result. We validate this new technique on a custom-built tungsten reference bar with an oxidized Inconel 625 solar-thermal absorber. A good agreement between the model and the experiment shows the reliability of the FOM measurement with a well-defined uncertainty. The same method can be implemented to measure the high-temperature FOM of most surface or volumetric solar absorbers for CSP.

14 SOLAR ENERGY↗
DOE OSTI2025

Designing Recyclable Biomass-Based Polyesters (Final Technical Report)

This project successfully demonstrated the production of sustainable polyesters from biomass-derived monomers, offering properties on par with or superior to fossil-based plastics such as LLDPE and PBAT. Using renewable chemical platforms like furfural and HMF, we synthesized over eight novel monomers and nearly 100 aliphatic-aromatic polyesters. Among these, PPeAT and PDDF emerged as highly promising candidates for flexible packaging applications, exhibiting excellent mechanical performance, tunable thermal properties, and enhanced barrier characteristics. Key advances included the development of ring-opening polymerization strategies using cyclic monomer intermediates to produce high molecular weight materials with excellent control. The resulting polymers achieved biobased content of at least 44 wt.%. We also implemented chemical recycling via catalytic methanolysis, recovering over 90% of monomers from PPeAT at semi-pilot scale. This supports a circular economy approach by enabling material reuse without performance loss. Techno-economic and life cycle assessments confirmed that these polyesters can reduce greenhouse gas emissions by up to 50% compared to petroleum-derived alternatives. Favorable mechanical properties may further reduce material demand, and cost competitiveness was demonstrated under specific market conditions. Feedstock cost and environmental footprint were identified as primary levers for future optimization. In summary, the project met or closely approached all technical targets, including biodegradability, strength, and processing compatibility. While minor issues such as color and melting point variation remain, the results strongly support continued development and scale-up of these sustainable materials.

09 BIOMASS FUELS↗
DOE OSTI2026

Structural Heterogeneity in Medium-Entropy AgMnSbPbTe 4 for Glassy Thermal Transport and High Thermoelectric Performance

Medium-entropy semiconductors represent a unique category of entropy-engineered materials. They possess a considerable level of randomness in atomic mixing, although this is not sufficient to conclusively achieve single-phase structure stabilization, in contrast to high-entropy materials. This introduces strong competition between the formation of different phases, which can potentially lead to structural heterogeneity. Here, in this work, we uncover endotaxial nanoprecipitates in the microscopically identified homogeneous medium-entropy semiconductor AgMnSbPbTe 4 . These nanoprecipitates initially crystallize in a cubic phase $(Fm\bar{3}m)$ within kinetically stabilized AgMnSbPbTe 4 , subsequently evolving into a thermodynamically stable monoclinic phase $(P2_1/c)$ during thermal annealing while maintaining an endotaxial relationship with the matrix lattice. This nanophase segregation and the resultant lattice mismatch at interfaces introduce strain fluctuations up to 5% at intervals of 20 nm across the entire microstructure. Within the matrix phase, atomic displacement of up to 23 pm was observed. This structural heterogeneity results in glass-like thermal transport behavior, achieving an ultralow lattice thermal conductivity κ L = 0.312 Wm –1 K –1 at 800 K, which is in accordance with the amorphous limit predicted by the Cahill model. The synergy of band convergence effect and well-maintained carrier mobility leads to a maximum ZT of 1.72 at 800 K and an average ZT avg of 1.02 over the temperature range of 300–825 K. This study highlights that the underexplored structural heterogeneity in medium-entropy semiconductors can potentially yield beneficial phenomena, such as the phonon-glass electron-crystal transport behavior in this case, which holds promise for advancing thermoelectric applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

The effect of water on colloidal quantum dot solar cells

Almost all surfaces sensitive to the ambient environment are covered by water, whereas the impacts of water on surface-dominated colloidal quantum dot (CQD) semiconductor electronics have rarely been explored. Here, strongly hydrogen-bonded water on hydroxylated lead sulfide (PbS) CQD is identified. The water could pilot the thermally induced evolution of surface chemical environment, which significantly influences the nanostructures, carrier dynamics, and trap behaviors in CQD solar cells. The aggravation of surface hydroxylation and water adsorption triggers epitaxial CQD fusion during device fabrication under humid ambient, giving rise to the inter-band traps and deficiency in solar cells. To address this problem, meniscus-guided-coating technique is introduced to achieve dense-packed CQD solids and extrude ambient water, improving device performance and thermal stability. Our works not only elucidate the water involved PbS CQD surface chemistry, but may also achieve a comprehensive understanding of the impact of ambient water on CQD based electronics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A review of regulatory standard test methods for residential wood heaters and recommendations for their advancement

In many regions, residential wood heaters are a leading source of harmful air pollution but only satisfy a small portion of local heating demands. In response, standardized laboratory test methods have been developed to characterize and limit wood heater emissions. While these test methods are a key tool for advancing both wood heater technology and environmental regulations, many of the experimental procedures are outdated and provide few actionable insights for improving heater performance. Furthermore, these test methods vary widely around the world and may not adequately capture the performance of wood heaters operating in residences. This study presents a comprehensive review of standardized wood heater test methods to identify fundamental experimental objectives and regulated performance metrics. Using the results of this review, recommendations are provided to make the test methods more accessible and representative of residential performance, while generating actionable data to motivate heater design improvements. This study elucidates the current state of standard test methods, and the developments needed to advance clean wood heater technologies and public policies.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Green co-solvent-assisted one-pot synthesis of high-performance flexible lignin polyurethane foam

Although lignin is a promising candidate as a source of polyol for producing eco-friendly polyurethane foam (PUF), its direct application has limitations, primarily stemming from the brittleness of the resulting products and poor processibility at high lignin loadings. To address these technical challenges, we introduced an effective co-solvent for the lignin-based polyurethane foams (LPUFs) with up to 80wt% of lignin substitution for petroleum polyols. As a green co-solvent that involves carbon dioxide fixation during its production, propylene carbonate (PC), was blended with lignin and improved the distribution of lignin by decreasing the viscosity, providing a room-temperature reaction. The LPUFs demonstrated a comparable thermal insulation performance (R-values greater than 5 in -1 ) with commercially available PUF with a uniform size of closed-cell structure induced by the reduced viscosity of lignin-based polyol. LPUFs also showed enhanced fire retardancy and moisture resistance compared to the control PUFs, benefiting from lignin’s intrinsic fire-resistant and hydrophobic properties. To mitigate the brittleness issue at high lignin loadings, flexible polyethylene glycols (PEGs) with a high molecular weight (i.e., PEG-1000) were dissolved in PC at room temperature to further improve the mechanical strength of LPUFs. The compressive strength of LPUFs with 80 wt% lignin substitution content was remarkably improved to 226 kPa by the employment of co-solvent and PEG-1000 compared to the control PUF (<140 kPa). Moreover, the flexibility of the LPUFs was successfully controlled by simply adjusting the PEG-400/PEG-1000 ratio. In conclusion, the results of this study provide valuable insights for accelerating and broadening the utilization of lignin in sustainable materials and manufacturing areas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Development of an Advanced Multiphysics Simulation Capability for Radiant's Microreactor Design

Argonne National Laboratory and Idaho National Laboratory, through a Department of Energy Gateway for Accelerated Innovation in Nuclear Voucher, supported key analysis needs of Radiant related to (i) air jacket thermal fluid performance, (ii) evaluation of decay heat source terms defining air jacket technical requirements, and (iii) assessment of modeling methodologies employed for core analysis. All of these activities center on numerical simulation of various aspects of Kaleidos using the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework, the Cardinal multiphysics application, the OpenMC Monte Carlo code, and the Nek5000 computational fluid dynamics (CFD) code. This project builds upon an earlier Nuclear Energy Advanced Modeling and Simulation (NEAMS) Thermal-Hydraulic (T/H) Center of Excellence (CoE) project focused on initial demonstration of Cardinal multiphysics simulation of High Temperature Gas Reactors (HTGRs) and now focuses on Radiant’s Kaleidos concept.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Properties and performance of lignin-based polyurethane foams from lignin and castor oil as synergistic bio-polyols

Lignin and castor oil with intrinsic hydroxyl groups are attractive green resources for polyurethane (PU) applications. However, lignin's heterogeneous and highly crosslinked structure, poor processability, as well as the feedstock variability, lead to inconsistent and poor performance of the final foam products. Castor oil-based polyurethane foam (PUF) has a relatively high price and density, which are big hurdles to its practical applications. Here, in this study, we hypothesized that synergistic bio-polyol mixtures composed of lignin and castor oil could balance the drawbacks from individual component. Castor oil could improve the dispersity of lignin, while lignin simultaneously addressed the issues caused by PUF prepared with castor oil, such as its high density and low thermal stability. For a comprehensive understanding of the effects of structural properties of lignin on its PUF processing and applications, various lignin fractions were isolated by co-solvent enhanced lignocellulosic fractionation (CELF) from different species, including hardwood, softwood, and herbaceous plants, and the processed lignins with different molecular weights were applied with castor oil. The lignin fractions with lower molecular weight showed good dispersity in castor oil with a high lignin content (up to 50 wt%) and completely replaced petroleum-based polyols. The produced foam with 50 wt% low-molecular-weight lignin fractions from woody biomass showed comparable/higher compressive strength (up to 20 psi) and thermal insulation performance (up to 5.69 R-value in −1 for 50 % L-Pine foam). In addition, this study revealed the relationship between lignin's structural properties and foam performance, providing insights for practical applications of lignin-based PUF.

Jeong, Soyeon [State Univ. of New York (SUNY), Syr↗
DOE OSTI2021

Detection of diffusion limited oxidation in thermally aged ethylene propylene rubber cable insulation material

The lifetime prediction of electrical cable insulation in nuclear power plants (NPPs) is primarily based on accelerated aging. Polymeric insulation exposed to accelerated aging at high temperatures may demonstrate diffusion limited oxidation (DLO) where oxygen within the material is consumed faster than can be supplied by diffusion from the surrounding air. This situation leads to equilibrium oxidation at the exposed surfaces and limited oxidation away from the surfaces. Therefore, DLO results in a heterogeneously aged material which can lead to underestimation of lifetime for in-service cable insulation. In this study, the presence of inhomogeneous aging caused by DLO was evaluated on cross-sectioned cable insulation specimens made of ethylene propylene rubber (EPR). The studies were performed on thermally aged specimens (165 °C, 1 day and 165 °C, 16 days) using local measurement techniques including nanoindentation, micro-Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM) - energy dispersive spectroscopy (EDS). All the results indicate some degree of heterogenous aging, with 165 °C, 16 days, aging demonstrating highest degree of oxidative degradation on the inside edges presumably caused due to copper catalyzed oxidation.

Pallaka, Madhusudhan Reddy↗
DOE OSTI2022

Multiphysics Simulation of the Thermal Response of a Nanofibrous Target in a High-Intensity Beam

Nanofibrous structures are of high interest to the fields of engineering and materials science, and investigation of their properties as well as discovery of novel applications for them both constitute lively areas of research. A very promising application of nanofiber mats lies in the field of accelerator technology: beam targets made from nanofiber mats offer a solution to the problem of advancing the "intensity frontier"–-the limit on the beam intensities that can be realized in fixed target experiments and neutrino production facilities. However, testing has shown that the survivability of these nanofiber targets depends strongly on their manufacturing parameters, such as the packing density of fibers. In this work, we will use multiphysics simulations to perform a thermal study on how nanofiber targets react to high intensity beams, so that the dependency of the targets’ lifetime on their construction parameters can be better understood.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Design Optimization of A-Type Heat Exchangers based on High Performance, Non-Round Tubes

Air-to-refrigerant heat exchangers (HXs) have been the topic of considerable research as they are the fundamental heat transfer components of HVAC&R systems. For residential and commercial applications, indoor heat exchangers are often in A-type configurations to reduce air-conditioner system footprint while still delivering the required cooling or heating. Classical HX design practices typically assume a uniform frontal air velocity profile to facilitate the use of conventional tube-fin airside heat transfer and pressure drop correlations for performance prediction. However, it is well-reported throughout the literature that A-type HXs experience significant airflow maldistribution which can severely degrade HX performance. Additionally, recent advancements in simulation software such as Computational Fluid Dynamics (CFD), Finite Element Analysis (FEA) and optimization algorithms have led researchers to consider primary heat transfer surface optimization to achieve highly compact HXs which do not require fins. In this paper, an A-type HX which utilizes shape-optimized non-round tubes is optimized for minimum duct size and airside pressure drop. This is achieved through coupling of an experimentally validated finite volume HX model with automated 2D CFD simulations of airflow through the HX for airside thermal-hydraulic performance evaluation. Preliminary results show that the optimal designs deliver similar capacity while achieving 20% reductions in airside pressure drop and duct cross-section area. Additionally, the optimal design apex angles in this study were similar to those from previous A-Type HX optimization studies for conventional tube-fin HX geometries, suggesting that the apex angle for optimal A-Type configuration performance may be independent of tube geometry.

42 ENGINEERING↗
DOE OSTI2021

A Comparative Study of Layer Heating and Continuous Heating Methods on Prediction Accuracy of Residual Stresses in Selective Laser Melted Tube Samples

Thermal distortion and residual stresses are two important factors that affect the quality and reliability of steel parts manufactured by laser powder bed fusion (LPBF) processes. A cost-effective model for evaluation of those heat effects is needed to refine the manufacturing process and provides insights into the product design and heat treatment. In this study, the layer heating method and sophisticated track-layer scanning method were applied to simulate the thermo-mechanical response of IN625 tube parts built by LPBF. Based on the similarity of temperature field in each layer deposit, a swept mesh was constructed to perform the thermal analysis for top layer, with the rest of layers referring to the temperature by node number offsetting. A novel explicit finite element analysis code accelerated by graphics processing unit was used for the massive-element numerical analysis. The computational accuracy and efficiency of the layer heating and track-layer scanning methods were compared in detail. It is shown that layer heating method can efficiently capture the pattern of stress distribution with reasonable accuracy in stress magnitude. The grouped track-layer scanning method can predict the residual stress and strain more accurately at a higher cost (5 ~ 10×). The elastic strain distribution was compared with the measurement by X-ray diffraction, confirming the accuracy of residual stress prediction.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Impact of U-10Mo HALEU Fuel Element Tolerances on the Massachusetts Institute of Technology Reactor safety and operational performance – Neutronics

The U.S. is coordinating efforts for the conversion of six U.S. high performance research reactors (USHPRR), including one critical assembly from highly enriched uranium (HEU) to low-enriched uranium (LEU). In order to continue the mission of these reactors, including the Massachusetts Institute of Technology Reactor (MITR), and achieve similar performance, high assay low-enriched uranium (HALEU) with a high-density metallic alloy of uranium with 10 wt% molybdenum (U-10Mo) is being considered. Following the preliminary design of the proposed MITR LEU fuel elements using the U-10Mo monolithic alloy, the impact of the fabrication specification was assessed. This work focuses on the analysis of select neutronics characteristics of the MITR LEU core as a function of the variation of the relevant fuel specification parameters (e.g., U-10Mo composition, fuel plate thickness, etc.). A separate article submitted to this journal addresses the impact on the thermal hydraulic performance. The analyses in these works are performed based on an all-LEU conversion management plan identified in previous work, in which only the proposed elements are utilized for achieving the conversion of MITR. The variations of two main neutronics characteristics are assessed as a function of the variability of the specification parameters resulting from the fabrication process: the MITR LEU core reactivity and the fuel cycle length. The main findings of this work show that the MITR core can meet the operational requirements during the LEU transition plan under the limiting fabrication parameter combinations considered. In addition, the analyses show that the dependency of the core neutronics characteristics on the specification parameters is highly linear within the specification tolerances. The rates of variation are reported in detail for each parameter and can serve as a powerful tool for future MITR fuel management in cases such as when HALEU supply is established that may allow additional cycle length or other operational benefits.

Conversion↗
DOE OSTI2021

Additive Manufacturing of Porous Ceramics With Foaming Agent

The macro-porous ceramics has promising durability and thermal insulation performance. As porous ceramics find more and more applications across many industries, a cost-effective and scalable additive manufacturing technique for fabricating macro-porous ceramics is highly desirable. Herein, we reported a facile additive manufacturing approach to fabricate porous ceramics and control the printed porosity. Several printable ceramic inks were prepared, and the foaming agent was added to generate gaseous bubbles in the ink, followed by the direct ink writing and the ambient-pressure and room-temperature drying to create the three-dimensional geometries. In this work, a set of experimental studies were performed to optimize the printing quality. The results revealed the optimal process parameters for printing the foamed ceramic ink with a high spatial resolution and fine surface quality. Varying the concentration of the foaming agent enables the controllability of the structural porosity. The maximum porosity can reach 85%, with a crack-free internal porous structure. The tensile tests showed that the printed macro-porous ceramics possessed enhanced durability with the addition of fiber. With a high-fidelity three-dimensional (3D) printing process and the precise controllability of the porosity, we showed that the printed samples exhibited a remarkably low thermal conductivity and durable mechanical strength.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thermally induced PtOx interfacial layer enhances stability of Pt/β-Ga2O3 vertical Schottky diodes

This study investigates the long-term stability of Pt/β-Ga2O3 field-plated Schottky barrier diodes at high temperatures, with extended thermal cycling and soaking stress. The device characteristics reveal a strong dependence on operating temperature, leading to an ON/OFF current ratio of ∼10× at ±3 V and 600 °C. Extensive thermal cycling (25 cycles over 100 h) between room temperature and 350 °C shows that leakage currents stabilize after the initial ten cycles. This stabilization is likely due to the formation of a thin PtOx layer at the Pt/β-Ga2O3 interface, as confirmed by high-resolution scanning transmission electron microscopy. Further exposure to a constant 350 °C environment for 10 h reveals a slight increase in the leakage current from 10−7 to 10−6 A at −5 V and degradation of the forward current, due to potential thermodynamic instability of the Ohmic contacts. This study provides insights into the changes in the Pt/β-Ga2O3 diode performance with thermal stress, offering a basis for predicting the device’s operational reliability at high temperatures for sensing and power applications.

08 HYDROGEN↗
DOE OSTI2026

Fast, Controllable, and Modular Solid-State Circuit Breaker Design for Battery Management Systems

Electric power grid is experiencing a growing number of distributed and inertia-free generation resources. To facilitate the growing generation and load demands, and ensure stable operation, energy storage systems, especially behind-themeter-storage (BTMS), have emerged as a potential candidate. BTMS plays a vital role in the grid storage sector and supports high power charging for EVs. However, the potential of thermal runaway and associated safety concerns in the batteries can hamper their widespread adoption. In this work, we provide a solution for a fast and controllable discharge of a cell that was identified as a stressful/faulty, in the battery pack, and fast circuit breaking leveraging the Solid-State Circuit Breaker (SSCB) technology which provides active control over the cell connection as opposed to conventional passive solutions. Testing on the simulation platform successfully validated the concept, demonstrating its efficacy. Controlled discharge testing with 20Ah LiFePO4 Lithium Iron Phosphate (LFP) cells from 1C-10C current rate on the hardware prototype corroborated simulation results, demonstrating design feasibility and providing essential data for its performance and thermal characteristics, while also revealing limitations that inform areas for further optimization.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Structure property correlations in wet-spun textile PAN fibers for cost-effective carbon fibers applicable in H 2 storage tank manufacturing

The economic viability of high-strength carbon fibers is pivotal for their integration into Type IV compressed hydrogen storage tanks. Oak Ridge National Laboratory is advancing this objective by developing cost-effective, textile-grade polyacrylonitrile (PAN) precursor fibers through an optimized wet spinning-process to garner more microstructural control over the precursor fibers. Here, this study examines the microstructural characteristics of PAN fibers, particularly the crystalline orientation factor, and their impact on mechanical properties in both precursor and thermally converted carbon fibers (CFs). Three wet-spun PAN fibers, all having diameters of 12-13 µm but varying orientation factors were assessed. Comprehensive characterization using X-ray scattering and microscopy revealed that fibers with higher orientation factors exhibited enhanced crystallinity and optimized crystallite sizes. Mechanical testing demonstrated that the PAN fiber with the highest orientation factor achieved the greatest tensile strength (98 ksi) and modulus (1.60 Msi). Additionally optical and scanning electron microscopy confirmed smooth and defect-free surfaces across all samples. These findings indicate that manipulating spinning parameters to maximize orientation factor is more impactful in achieving high strength and modulus over factors attributed to crystallinity and crystallite sizes. Here, highest performing CFs, thermally processed in lab from textile-grade precursor averaged 558 ksi, a 10% increase over previous results.

36 MATERIALS SCIENCE↗