Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TPS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Flow through the tile gaps in the Space Shuttle Thermal Protection System

The problem of predicting aerodynamic loads on the insulating tiles of the Space Shuttle Thermal Protection System (TPS) is discussed and seen to require a method for predicting pressure and mass flux in the gaps between tiles. A mathematical model of the tile-gap flow is developed based upon a slow viscous (Stokes) flow analysis and is verified against available experimental data. This model derives the tile-gap pressure field from a solution of the two-dimensional Laplace equation; the mass flux vector is then calculated from the pressure gradient. The means for incorporating this model into a lumped-parameter network analogy for porous-media flow is also given. The flow model shows tile-gap mass flux to be very sensitive to the gap width indicating a need for coupling the TPS flow and tile displacement calculations. Finally recommendations are made concerning additional analytical and experimental work to improve TPS flow predictions.

Dwoyer, D. L.↗
NASA NTRS1982

Benchmark aerodynamic heat-transfer data from the first flight of the Space Shuttle Orbiter

Benchmark entry aerodynamic heat-transfer data were determined from the first flight of the Space Shuttle Orbiter. The convective heating-rate data result from a rigorous mathematical analysis of one-dimensional, transient heat conduction within the orbiter thermal protection system (TPS) and reradiation from its surface during entry. Temperatures measured at the TPS surface during orbiter entry provide a constraint to the analysis. On the vehicle leeside, where heating rate levels are low, corrections are made to the computed convective heating rates to account for solar radiation and cross-radiation between fuselage and wing surfaces. The source of the entry thermal data, the mathematical analysis technique, and the TPS thermal models are discussed. Typical convective heating rate data from the STS-1 mission are presented.

Throckmorton, D. A.↗
NASA NTRS1982

Assessment of alternate thermal protection systems for the Space Shuttle Orbiter

Technical aspects of the alternate thermal protection system (TPS) study for the Shuttle Orbiter are reviewed, and a status report on alternate TPS technology developments is presented. Mission impact, life cycle costs and risks, and selected candidate concepts are identified. The best system would consist of mechanically attached metallic and carbon-carbon TPS concepts employing a titanium multiwall prepackaged concept at temperatures below 1000 F, a superalloy honeycomb prepackaged concept at temperatures between 1000-1800 F, and an advanced carbon-carbon multipost standoff concept above 1800 F. Alternative concepts offer significant improvements in durability and are mass competitive with current ceramic tile reusable surface insulation.

Kelly, H. N.↗
NASA NTRS1983

Ablative thermal protection systems

The procedures used to establish the TPS (thermal protection system) design of the SRB (solid rocket booster) element of the Space Shuttle vehicle are discussed. A final evaluation of the adequacy of this design will be made from data obtained from the first five Shuttle flights. Temperature sensors installed at selected locations on the SRB structure covered by the TPS give information as a function of time throughout the flight. Anomalies are to be investigated and computer design thermal models adjusted if required. In addition, the actual TPS ablator material loss is to be measured after each flight and compared with analytically determined losses. The analytical methods of predicting ablator performance are surveyed.

Vaniman, J.↗
NASA NTRS1983

Space shuttle orbiter reusable surface insulation flight results

The first five flights of the orbiter Columbia provided the initial data required to certify the operational performance of the reusable surface insulation (RSI) thermal protection system (TPS). The flight performance characteristics of the RIS TPS are discussed. The discussion is based primarily on postflight inspections and postflight interpretation of the flight instrumentation. TPS modifications of the future orbiters (OV-099, 103, and subs) are also discussed.

Dotts, R. L.↗
NASA NTRS1984

Aerothermal performance and damage tolerance of a Rene 41 metallic standoff thermal protection system at Mach 6.7

A flight-weight, metallic thermal protection system (TPS) model applicable to Earth-entry and hypersonic-cruise vehicles was subjected to multiple cycles of both radiant and aerothermal heating in order to evaluate its aerothermal performance, structural integrity, and damage tolerance. The TPS was designed for a maximum operating temperature of 2060 R and featured a shingled, corrugation-stiffened corrugated-skin heat shield of Rene 41, a nickel-base alloy. The model was subjected to 10 radiant heating tests and to 3 radiant preheat/aerothermal tests. Under radiant-heating conditions with a maximum surface temperature of 2050 R, the TPS performed as designed and limited the primary structure away from the support ribs to temperatures below 780 R. During the first attempt at aerothermal exposure, a failure in the panel-holder test fixture severely damaged the model. However, two radiant preheat/aerothermal tests were made with the damaged model to test its damage tolerance. During these tests, the damaged area did not enlarge; however, the rapidly increasing structural temperature measuring during these tests indicates that had the damaged area been exposed to aerodynamic heating for the entire trajectory, an aluminum burn-through would have occurred.

Avery, D. E.↗
NASA NTRS1983

Thermal response of advanced high temperature ceramic-composite insulation to a convectively heated environment

The Space Shuttle uses currently fibrous high temperature, reusable surface insulation (HRSI) as a Thermal Protection System (TPS) at 1260 C for normal-design mission operation. Higher density material of a similar type extended the maximum temperature to 1480 C. However, a surface temperature capability exceeding 1540 C is desired for future space vehicles, such as the Orbital Transfer Vehicle (OTV). A TPS providing such a capability would permit future entry vehicles to enter the atmosphere at a much higher velocity than the Space Shuttle. The present investigation is concerned with arc-jet test data obtained from a family of fibrous refractory-composite insulation (FRCI) materials developed to meet the future TPS requirements. FRCI materials containing between 20 and 80 percent aluminoborosilicate fibers with the balance composed of silica fibers were studied.

Stewart, D. A.↗
NASA NTRS1983

Moisture absorption characteristics of the Orbiter thermal protection system and methods used to prevent water ingestion

The Space Shuttle Orbiter's silica tile Thermal Protection System (TPS) is beset by the moisture absorption problems inherently associated with low density, highly porous insulation systems. Attention is presently given to the comparative success of methods for the minimization and/or prevention of water ingestion by the TPS tiles, covering the development of water-repellent agents and their tile application techniques, flight test program results, and materials improvements. The use of external films for rewaterproofing of the TPS tiles after each mission have demonstrated marginal to unacceptable performance. By contrast, a tile interior waterproofing agent has shown promise.

Schomburg, C.↗
NASA NTRS1984

Thermal mathematical modeling and system simulation of Space Shuttle less subsystem

Applications, validation tests, and upgrades of the two- and three-dimensional system level thermal mathematical system simulation models (TMSSM) used for thermal protection system (TPS) analyses are described. The TMSSM were developed as an aid to predicting the performance requirements and configurations of the Shuttle wing leading edge (WLE) and nose cone (NC) TPS tiles. The WLE and its structure were subjected to acoustic, thermal/vacuum, and air loads tests to simulate launch, on-orbit, and re-entry behavior. STS-1, -2 and -5 flight data led to recalibration of on-board instruments and raised estimates of the thermal shock at the NC and WLE. Baseline heating data are now available for the design of future TPS.

Chao, D. C.↗
NASA NTRS1985

Thermal design of the space shuttle solid rocket booster

The thermal protection systems (TPS) to meet the quick turnaround and low cost required for reuse of the solid rocket booster (SRB) hardware. The TPS development considered the ease of application, changing ascent/reentry environments, and the problem of cleaning the residual insulation upon recovery. A sprayable ablator TPS material was developed. The challenges involved in design and development of this thermal system are discussed.

Fisher, R. R.↗
NASA NTRS1986

Heatshield design for transatmospheric vehicles

A variety of future spacecraft will be operating above the sensible earth atmosphere, but will be dipping into the atmosphere to utilize aerodynamic forces in conjunction with propulsion for its major maneuvers such as plane change. During this maneuver, the vehicle surface will experience high aerodynamic heating rates. Because these heating rates can exceed those experienced by the Shuttle, advanced thermal protection systems (TPS) must be used. This paper compares the performance of four TPS concepts operating in the same heating environment. All of them can be considered as derivatives from the development process of the TPS for the Shuttle; one has a new feature added. The results show that all of the systems require about the same weight of heatshield at high heat loads. The major difference in the weight stems from the methods of attachment to the spacecraft.

Pitts, W. C.↗
NASA NTRS1987

Aerothermal evaluation of a spherically blunted body with a trapezoidal cross section in the Langley 8-foot high-temperature tunnel

A model to be used in the flow studies and curved Thermal Protection System (TPS) evaluations was tested in the Langley 8 Foot High-Temperature Tunnel at a nominal Mach number of 6.8. The purpose of the study was to define the surface pressure and heating rates at high angles of attack (in support of curved metallic TPS studies) and to determine the conditions for which the model would be suitable as a test bed for aerothermal load studies. The present study was conducted at a nominal total temperature of 2400 and 3300 R, dynamic pressures from 2.3 to 10.9 psia, and free-stream Reynolds numbers from 4000,000 to 1,700,000/ft. The measurements consisted primarily of surface pressure and cold-wall (530 R) heating rates. Qualitative comparisons between predictions and data show that for this configuration, aerothermal tests should be limited to angles of attack between 10 and -10 degrees. Outside this range, the effects of free-stream flow nonuniformity appear in the data, as a result of the long length of the model. However, for TPS testing, this is not a concern and tests can be performed at angles of attack ranging from 20 to -20 degrees. Laminar and naturally turbulent boundary layers are available over limited ranges of conditions.

Albertson, Cindy W.↗
NASA NTRS1987

Development and test of the Shuttle/Centaur cryogenic tankage thermal protection system

The Thermal Protection System (TPS) for the Shuttle/Centaur had to provide fail-safe thermal protection during prelaunch, launch ascent, and on-orbit operations as well as during potential abort where the Shuttle and Centaur would return to earth. The TPS selected used a helium-purged polyimide foam beneath three radiation shields for the liquid hydrogen (LH2) tank and radiation shields only for the liquid oxygen (LO2) tank (three shields on the tank sidewall and four on the aft bulkhead). An evacuated common intermediate bulkhead separated the two tanks. The LH2 tank had one 1.9-cm thick layer of foam on the forward bulkhead and two layers on the larger area side-wall. Full scale tests of the flight vehicle in a simulated Shuttle cargo bay, that was purged with gaseous nitrogen, gave total prelaunch heating rates of 25.9 kW and 12.9 kW for LH2 and LO2 tanks, respectively. Calorimeter tests on a representative LH2 tank sidewall TPS sample indicated that the measured unit heating rate would rapidly decrease from the prelaunch rate of 300 W/sq m to a desired rate of less than 4 W/sq m once on-orbit.

Knoll, R. H.↗
NASA NTRS1987

Effects of forced and free convections on structural temperatures of Space Shuttle Orbiter during reentry flight

Structural performance and resizing (SPAR) finite-element thermal analysis computer program was used in the heat transfer analysis of the Space Shuttle Orbiter wing subjected to reentry aerodynamic heating. With sufficient external forced convective cooling near the end of the heating cycle, the calculated surface temperatures of the thermal protection system (TPS) agree favorably with the flight data for the entire flight profile. However, the effects of this external forced convective cooling on the structural temperatures were found to be negligible. Both free convection and forced convection elements were introduced to model the internal convection effect of the cool air entering the Shuttle interior. The introduction of the internal free convection effect decreased the calculated wing lower skin temperatures by 20 F at most, 1200 sec after touchdown. If the internal convection is treated as forced convection, the calculated wing lower skin temperatures after touchdown can be reduced to match the flight-measured data very closely. By reducing the TPS thicknesses to certain effective thickness to account for the TPs gap heating, the calculated wing lower skin temperatures prior to touchdown can be raised to agree with the flight data perfectly.

Ko, William L.↗
NASA NTRS1988

In-flight rain damage tests of the shuttle thermal protection system

NASA conducted in-flight rain damage tests of the Shuttle thermal protection system (TPS). Most of the tests were conducted on an F-104 aircraft at the Dryden Flight Research Facility of NASA's Ames Research Center, although some tests were conducted by NOAA on a WP-3D aircraft off the eastern coast of southern Florida. The TPS components tested included LI900 and LI2200 tiles, advanced flexible reusable surface insulation, reinforced carbon-carbon, and an advanced tufi tile. The objective of the test was to define the damage threshold of various thermal protection materials during flight through rain. The test hardware, test technique, and results from both F-104 and WP-3D aircraft are described. Results have shown that damage can occur to the Shuttle TPS during flight in rain.

Meyer, Robert R., Jr.↗
NASA NTRS1988

Effects of natural environment on first generation solid rocket booster thermal protection system materials

The effort to demonstrate, by real-time exposure, the effects of the natural environment at Kennedy Space Center, Florida, upon the Thermal Protection System (TPS) of the Solid Rocket Booster (SRB) is summarized, and that the overall SRB TPS configuration is verified to meet all requirements for resistance to the conditions associated with outdoor weathering, including: solar radiation; temperature; humidity; precipitation; wind; sand/dust abrasion; static electricity; salt spray; fungus; and atmospheric oxidants. The evaluation criterion for this project was based upon flatwise tensile properties, visual inspection, color change, and thermal performance. Based upon the evaluation of the changes in these properties, it is concluded that properly applied and topcoat-protected TPS can satisfactorily withstand the conditions of the natural environment at KSC for exposures up to six months.

Webb, D. D.↗
NASA NTRS1988

Design, development, and test of Shuttle/Centaur G-prime cryogenic tankage thermal protection systems

The thermal protection systems (TPS) for the Shuttle/Centaur were designed to provide fail-safe thermal protection during prelaunch, launch ascent, and on-orbit operations as well as during potential abort, where the Shuttle and Centaur would return to earth. The TPS selected used a helium-purged polyimide foam beneath three radiation shields for the liquid-hydrogen (LH2) tank and radiation shields only for the liquid-oxygen (LO2) tank. A double-walled vacuum bulkhead separated the two tanks. The LH2 tank had one 1.9 cm-thick layer of foam on the forward bulkhead and two layers on the larger-area sidewall. Full scale tests of the flight vehicle in a simulated Shuttle cargo bay gave total prelaunch heating rates of 29.5 and 12.9 kW for the LH2 and LO2 tanks, respectively. Calorimeter tests on a representative sample of the LH2 tank sidewall TPS indicated that the measured unit heating one would rapidly decrease from the prelaunch rate of about 300 W/sq m to a desired rate less than 4 W/sq m once on-orbit.

Macneil, Peter N.↗
NASA NTRS1989

Thermal Stresses In Space-Shuttle Wing

Combined thermal deformations of wing-skin panel and TPS would not tear SIP layer. Report presents analysis of thermal stresses induced in skin panel, thermal-protection system (TPS), and strain-isolation pad (SIP) of Space Shuttle orbiter. Purpose of analysis to determine whether any part of above mentioned structures overstressed and overdeformed under reentry heating, assuming one TPS tile lost at end of reentry heating.

Ko, William L.↗