Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solvent effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Investigating the Role π -Rich Solvents Play in the Growth of Cesium Lead Bromide Nanocrystals

In this report, the role that a high-boiling-point solvent type plays on the nucleation and growth, morphology, and crystal-phase transformation of cesium lead bromide nanocrystals (CsPbBr 3 ) is studied. The CsPbBr 3 products were compared between a one-pot growth mechanism at room temperature (RT) versus a hot-injection mechanism (HI) control using dibenzyl ether (DBE), diphenyl ether (DPE), dioctyl ether (DOE), or 1- octadecene (ODE). The coordination between these solvents and the PbBr 2 salt precursors resulted in different plumbate [PbSBr n ] 2−n precursors being formed. The S-to-Pb 2+ coordination within [PbSBr n ] 2−n was probed by UV−vis and solvent-phase 207 Pb NMR, both of which showed considerable coordination between [PbSBr n ] 2−n and the π-rich DBE and DPE, whose reactivity affected CsPbBr 3 growth. The effect was more pronounced for CsPbBr 3 prepared via RT, where the morphology was tunable, with π-rich solvents producing thin rod-like CsPbB r3 with a blue emission, compared to the green-emitting thicker platelets formed via HI. While XRD showed crystalline products for both RT and HI, with orthorhombic and cubic forms, respectively, the RT products had considerable surface defects, as was indicated by lower quantum yields, and to understand this the photoluminescent lifetimes were measured by time-correlated single photon counting.

207Pb NMR↗
DOE OSTI2020

Evaporation due to infrared heating and natural convection

The results obtained from a drying experiment under infrared heating are compared to those obtained from correlations for the mass transfer coefficients, which are commonly used to obtain evaporation rates for drying applications. It was shown that the mass transfer coefficients evaluated by natural convection correlations are approximately ten times lower than those measured under infrared (IR) exposure. In this work, an attempt to explain this discrepancy, which has been also observed in other studies and explained on the basis of thermal radiation effects, optical properties of NMP are presented and the implications of the IR and near infrared (NIR) spectrum on the thermal radiation effects and ensuing evaporation rates are discussed. The results show that expected raise in the film temperature, which would be due to the thermal radiation effects, cannot be used to describe the measured evaporation rates for this solvent. Therefore, this study provides important evaporation mass flux data, which cannot be predicted using traditional correlations, for the design of IR assisted drying systems used in membrane fabrication.

42 ENGINEERING↗
DOE OSTI2021

Structure and Shape of Surface-Mediated Assembly of Surfactants

Achieving controls on the self-assembly of cationic and block copolymer micelles has significant implications for advancing novel material systems for energy, environmental, and biological applications and for tuning fluid flow behavior in subsurface geologic environments. While it is known that the aggregation of micelles is influenced by the composition of the surrounding fluid, the influence of a solid interface has been less explored. In this study, we probe the organization of cetyltrimethylammonium bromide (CTAB) micelles in the absence and presence of the Pluronic P123 block copolymer and quartz substrate using transmission and grazing-incidence small-angle X-ray scattering measurements and classical molecular dynamics (MD) simulations. In the absence of the quartz interface, CTAB with and without P123 molecules assemble as ellipsoid core–shell micelles. Densification of the core on adding P123 is noted from the decrease in the core radius from 15.9 to 14.6 Å. Here, the presence of a quartz substrate causes the micelles to elongate, which is noted by the emergence of a power-law slope in the low q region (<0.02 Å –1 ). Moreover, in the presence of both P123 and the quartz substrate, the micelle shape changes from ellipsoid core–shell to cylindrical core–shell, and a significantly higher number of aggregates are formed. The higher number of aggregates, and faster aggregation kinetics are linked to the organization of the solvent structures as noted from the MD simulations. These findings demonstrate the effects of adding a block copolymer and including a quartz substrate on the self-assembly of cationic (CTAB) micelles, which can be used to inform the design of functional material systems that harness surfactant chemistries.

42 ENGINEERING↗
DOE OSTI2021

Origin of Proteolytic Stability of Peptide-Brush Polymers as Globular Proteomimetics

Peptide-brush polymers (PBPs), wherein every side-chain of the polymers is peptidic, represent a new class of proteomimetic with unusually high proteolytic resistance while maintaining bioactivity. Here, we sought to determine the origin of this behavior and to assess its generality via a combined theory and experimental approach. A series of PBPs with various polymer backbone structures were prepared and examined for their proteolytic stability and bioactivity. We discovered that an increase in the hydrophobicity of the polymer backbones is predictive of an elevation in proteolytic stability of the side-chain peptides. Computer simulations, together with small-angle X-ray scattering (SAXS) analysis, revealed globular morphologies for these polymers, in which pendant peptides condense around hydrophobic synthetic polymer backbones driven by the hydrophobic effect. As the hydrophobicity of the polymer backbones increases, the extent of solvent exposure of peptide cleavage sites decreases, reducing their accessibility to proteolytic enzymes. This study provides insight into the important factors driving PBP aqueous-phase structures to behave as globular, synthetic polymer-based proteomimetics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Surface molecular pump enables ultrahigh catalyst activity

The performance of electrocatalysts is critical for renewable energy technologies. While the electrocatalytic activity can be modulated through structural and compositional engineering following the Sabatier principle, the insufficiently explored catalyst-electrolyte interface is promising to promote microkinetic processes such as physisorption and desorption. By combining experimental designs and molecular dynamics simulations with explicit solvent in high accuracy, we demonstrated that dimethylformamide can work as an effective surface molecular pump to facilitate the entrapment of oxygen and outflux of water. Dimethylformamide disrupts the interfacial network of hydrogen bonds, leading to enhanced activity of the oxygen reduction reaction by a factor of 2 to 3. This strategy works generally for platinum-alloy catalysts, and we introduce an optimal model PtCuNi catalyst with an unprecedented specific activity of 21.8 ± 2.1 mA/cm 2 at 0.9 V versus the reversible hydrogen electrode, nearly double the previous record, and an ultrahigh mass activity of 10.7 ± 1.1 A/mg Pt .

Science & Technology - Other Topics↗
DOE OSTI2021

Degradation of Platinum-Cobalt Alloy PEMFC Cathode Catalysts in Catalyst-Ionomer Inks

In this paper we report on studies of the effects of catalyst-ionomer ink composition: ionomer equivalent weight (EW), ink solvent, and ink mixing on a commercial PtCo alloy PEMFC cathode catalyst. X-ray absorption spectroscopy (XAS) and wide-angle X-ray scattering (WAXS) are utilized to determine catalyst atomic structure, catalyst crystallite composition, and extent of loss of Co into the ionomer-solvent phase. Three different n-propanol to water weight ratios (7:3, 5:5, and 3:7) and two different ionomers (3 M 800 EW and Nafion 1000 EW) were studied. Cobalt loss from the PtCo particles was found to increase with increasing water content in the inks and to be more extensive for the 800 EW ionomer inks, causing loss of contraction of the PtCo lattice and formation of a Pt shell-PtCo alloy core intraparticle structure.

25 ENERGY STORAGE↗
DOE OSTI2022

Concentration-dependent ion correlations impact the electrochemical behavior of calcium battery electrolytes.

Ion interactions strongly determine the solvation environments of multivalent electrolytes even at concentrations below that required for practical battery-based energy storage. This statement is particularly true of electrolytes utilizing ethereal solvents due to their low dielectric constants. These solvents are among the most commonly used for multivalent batteries based on reactive metals (Mg, Ca) due to their reductive stability. Recent developments in multivalent electrolyte design have produced a variety of new salts for Mg2+ and Ca2+ that test the limits of weak coordination strength and oxidative stability. Such electrolytes have great potential for enabling full-cell cycling of batteries based on these working ions. However, the ion interactions in these electrolytes exhibit significant and non-intuitive concentration relationships. In this work, we investigate a promising exemplar, calcium tetrakis(hexafluoroisopropoxy)borate (Ca(BHFIP)(2)), in the ethereal solvents 1,2-dimethoxyethane (DME) and tetrahydrofuran (THF) across a concentration range of several orders of magnitude. Surprisingly, we find that effective salt dissociation is lower at relatively dilute concentrations (e.g. 0.01 M) than at higher concentrations (e.g. 0.2 M). Combined experimental and computational dielectric and X-ray spectroscopic analyses of the changes occurring in the Ca2+ solvation environment across these concentration regimes reveals a progressive transition from well-defined solvent-separated ion pairs to de-correlated free ions. This transition in ion correlation results in improvements in both conductivity and calcium cycling stability with increased salt concentration. Comparison with previous findings involving more strongly associating salts highlights the generality of this phenomenon, leading to important insight into controlling ion interactions in ether-based multivalent battery electrolytes.

Hahn, Nathan T.↗
DOE OSTI2021

Subtask 2.6 – Optimization of Aerosol Mitigation Technology for Postcombustion CO 2 Capture

Growing concerns over the impact of CO 2 emissions from combustion sources on global climate change have prompted numerous research and development projects aimed at developing cost-effective technologies for CO 2 capture. One family of technologies being demonstrated at pilot and full scale globally is postcombustion CO 2 capture (PCCC) systems that employ amine-based solvents. The captured CO 2 can be compressed and permanently stored underground or used for enhanced oil recovery (EOR). The proximity of North Dakota’s lignite-fired fleet of power plants to potential CO 2 storage options creates a unique atmosphere for PCCC within the state. However, the aerosols present in lignite flue gas present a challenge for large-scale PCCC at North Dakota power plants. Aerosols can negatively impact the long-term performance of amine-based solvents for CO 2 capture. Amine-based solvents are volatile, and aerosols provide nucleation sites where amine vapors can condense. Because aerosols cannot be easily captured at the column outlet using conventional technologies, the amine-laden aerosols escape the system and lead to accelerated solvent losses. Moreover, aerosol components can chemically react with amines to form degradation products that can permanently deactivate the amine, cause fouling, and lead to hazardous emissions. Many of the elements that have been shown to catalyze solvent degradation are present in lignite coals and can exacerbate solvent replacement economics. Understanding this issue is critical to the implementation of solvent-based CO 2 capture systems as applied to lignite-fired generation systems. The Energy & Environmental Research Center (EERC) designed and carried out this project to optimize aerosol mitigation technology for PCCC at a lignite-fired power plant. To meet the goal of this project, the following objectives were identified: Determine the effectiveness of a wet electrostatic precipitator (WESP) on collection of aerosols at a low-rank coal-fired power station. Determine the impact of aerosols on the efficiency and degradation products of amine-based carbon capture systems fired with low-rank fuels. Work was conducted at Minnkota Power Cooperative’s (MPC’s) Milton R. Young (MRY) Station Unit 2 using a slipstream of flue gas from the outlet of the plant’s flue gas desulfurization (FGD) unit. To gather initial data for sizing and specifying a WESP for this system, a temporary pilot-scale WESP was rented and installed on-site. Several different conditions were tested to examine the impact of flow rate, voltage, and current on WESP performance. The WESP was effective at removing large particulate (>200 nm) but caused an increase in fine particulate (<75 nm). Fine particulate material at the inlet and outlet of the WESP was collected, analyzed, and showed that crystalline sulfates carried over from the plant’s FGD unit were being converted to fine aerosols and SO 2 was being converted to SO 3 through the WESP. Additionally, the high moisture content of the flue gas stream at this sample location also contributed to an overall increase in aerosol mass under some of the test conditions. Using the results from the rented WESP, the project team installed a smaller-scale WESP upstream of the EERC’s slipstream CO 2 capture system. Flue gas was routed through a pilot-scale FGD unit to remove SO 2 to very low levels (~1 ppm) and then through a direct contact cooler (DCC) to further cool the gas and to remove moisture. The gas exiting the DCC was then routed through the new WESP before passing to the CO 2 absorber columns. Fluor’s amine-based solvent was used to scrub CO 2 from the slipstream through a set of two absorber columns. The rich solvent was regenerated in a stripper column by heating to drive off captured CO 2 . The system operated using a catch-and-release method where the CO 2 was separated to provide data on the process, but the captured CO 2 was released back into the host site stack. Aerosols and sulfur species were measured at multiple locations throughout the pilot-scale system. The inlet FGD and DCC removed much of the particulate matter and gaseous sulfur upstream of the WESP. With this configuration, the WESP achieved >95% particulate capture. The new WESP did not show any of the increases in SO 3 or other aerosol species that had been consistently observed with the larger-scale WESP installed immediately downstream of the plant’s full-scale FGD unit. Particulate samples captured and analyzed from the WESP inlet did not show any presence of crystalline sulfate materials, indicating that the pilot-scale FGD and DCC were efficient at reducing carryover from the plant’s full-scale FGD unit. A set of parametric tests were conducted on the new WESP to assess the impacts of flow rate, voltage, number of online WESP fields, and gas-phase sulfur content on aerosol and sulfur transformations. The results showed that the WESP performed similarly well at all sets of conditions. Sulfur and particulate matter exiting the WESP were further reduced through the absorber column as the amine-based solvent captured some of the residual contaminants. Solvent analysis showed that these species were slowly concentrating in the solvent over the duration of the test. When the WESP was taken offline and the sulfur slip through the FGD allowed to rise, the sulfate content in the solvent rose sharply, showing that the extra FGD and WESP were effective at reducing sulfate and cation uptake. This would be expected to extend amine-based solvent life by slowing the formation of heat-stable salts and other degradation products. This subtask was cofunded through the EERC–U.S. Department of Energy Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by the North Dakota Industrial Commission and MPC.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Effective biomass fractionation and lignin stabilization using a diol DES system

A sustainable and renewable biorefinery will increase the economic viability of lignocellulose-derived products. In this study, a diol-based deep eutectic solvent (DES) was developed to reduce the recalcitrance of bamboo, facilitate saccharification and valorize the lignin fraction. The DES pretreatment dramatically enhanced glucan digestibility by the effective removal of lignin (as high as 85.45%) and xylan (91.12%). Notably, the recovered lignin from DES pretreatment was protected during the fractionation, showing well-preserved β-O-4 structures (31.82%–59.06%). The mechanism of lignin protection was analyzed to be accomplished by incorporating the diol hydroxyl functional groups into the α position of the lignin β-O-4 structure via etherification. This work highlighted that diol DES is a promising pretreatment solvent to valorize both cellulose and lignin fractions with high enzymatic hydrolysis yield and high-quality lignin co-product.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Exploring non-adiabaticity to CO reduction reaction through ab initio molecular dynamics simulation

Non-adiabatic chemical reaction refers to the electronic excitation during reactions. This effect cannot be modeled by the ground-state Born-Oppenheimer molecular dynamics (BO-MD), where the electronic structure is at the ground state for every step of ions' movement. Although the non-adiabatic effect has been explored extensively in gas phase reactions, its role in electrochemical reactions, such as water splitting and CO 2 reduction, in electrolyte has been rarely explored. On the other hand, electrochemical reactions usually involve electron transport; thus, a non-adiabatic process can naturally play a significant role. In this work, using one-step CO 2 reduction as an example, we investigated the role of the non-adiabatic effect in the reaction. The reaction barriers were computed by adiabatic BO-MD and non-adiabatic real-time time dependent density functional theory (rt-TDDFT). We found that by including the non-adiabatic effect, rt-TDDFT could increase the reaction barrier up to 6% compared to the BO-MD calculated barrier when the solvent model is used to represent water. Simulations were carried out using explicit water molecules around the reaction site under different overpotentials, and similar non-adiabatic effects were found.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Correlation of Broad Absorption Band with Small Singlet‐Triplet Energy Gap in Organic Photovoltaics

Abstract Organic photovoltaics (OPV) are one of the most effective ways to harvest renewable solar energy, with the power conversion efficiency (PCE) of the devices soaring above 19 % when processed with halogenated solvents. The superior photocurrent of OPV over other emerging photovoltaics offers more opportunities to further improve the efficiency. Tailoring the absorption band of photoactive materials is an effective way to further enhance OPV photocurrent. However, the field has mostly been focusing on improving the near‐infrared region photo‐response, with the absorption shoulders in short‐wavelength region (SWR) usually being neglected. Herein, by developing a series of non‐fullerene acceptors (NFAs) with varied side‐group conjugations, we observe an enhanced SWR absorption band with increased side‐group conjugation length. The underpinning factors of how molecular structures and geometries improve SWR absorption are clearly elucidated through theoretical modelling and crystallography. Moreover, a clear relationship between the enhanced SWR absorption and reduced singlet‐triplet energy gap is established, both of which are favorable for the OPV performance and can be tailored by rational structure design of NFAs. Finally, the rationally designed NFA, BO‐TTBr, affords a decent PCE of 18.5 % when processed with a non‐halogenated green solvent.

Chemistry↗
DOE OSTI2026

Toluene Uptake and Outgassing by a 3D-Printed Silicone and the Impact on Mechanical Performance

Silicone elastomers have advantageous physical properties and are widely used in various applications. Additive manufacturing (AM) of silicones provides additional utility by enabling tunable mechanical and functional properties. However, the performance of these elastomers deteriorates over time with exposure to environmental stressors. Organic solvents and volatile organic compounds (VOCs) are stressors that can cause dimensional changes to silicones with exposure and impact the overall function. Yet, the effects of such exposure on mechanical performance, including load response (LR), are not well understood. Here, in this study, we investigated the impact of a nonpolar solvent, toluene, on AM silicone material properties and compressive load. We observed that AM silicones rapidly absorbed toluene and swelled, leading to an increase in relative LR. Toluene concentration and compression did not affect uptake or swelling rates. In contrast, outgassing rates were slower for compressed coupons compared to uncompressed specimens, attributed to geometric constraints and polymer network changes impacting toluene diffusion outward. Compression also pinned the AM silicones at an enlarged state, significantly reducing relative LR after outgassing. Depending on toluene concentrations and compression, AM silicones can remain robust against toluene exposure and recover their initial printing geometry and mechanical performance after toluene outgassing and polymer relaxation.

Materials science↗
DOE OSTI2020

Ring patterns generated by an expanding colloidal meniscus

The drop-and-dry is a common technique allowing for creation of periodic nanoparticle (NP) structures for sensing, photonics, catalysis, etc. However, the reproducibility and scalability of this approach for fabrication of NP-based structures faces serious challenges due to the complexity of the simple, at first glance, evaporation process. In this work we study the effect of the spatial confinement on the NP self-assembly under slow solvent evaporation, when the air-liquid-substrate contact line (CL) expands from the center towards the walls of a cylindrical cell, forming a toroid. Using in situ video monitoring of the stick-slip CL motion, we find regular hydrodynamic perturbations in the meniscus, and reveal fine details of the formation of quasiperiodic rings of close packed NP layers. We report that drying of the toroidal NP droplet has a number of important differences from drying of the classical hemispherical colloidal drops. In toroidal drops we observe linear-in-time average meniscus motion, in contrast to the hemispherical drops where the meniscus moves as a square root of time. While both droplet geometries produce NP ring patterns, the ring width for the toroidal drop decreases with increasing ring radius, while it decreases with decreasing the radius of the hemispherical drop. We suggest that free ligands are the main cause of the Marangoni instabilities driving the periodic vorticity in the meniscus. Finally, we show that the usually ignored contact line tension may yield a considerable contribution to the CL pinning causing the CL slip-stick motion and the ring formation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Solvation Dynamics of Wet Ethaline: Water is the Magic Component

The past two decades witnessed the development of a new type of solvent system, named deep eutectic solvents, which have become increasingly investigated because they offer new and potentially favorable properties, such as wide tunability in electrochemical, mechanical, and transport properties. Deep eutectic solvent (DES) systems are composed of at least one main solvent and an additional component that is meant to interrupt the original solvent/solvent interactions, thereby introducing lower melting points relative to each individual component. Ethaline (a 1:2 mole% mixture of choline chloride and ethylene glycol) is one of the most promising DES systems. However, it is also known to be very hygroscopic, which is a constant concern because water absorption during the use of ethaline alters its properties. Within this work, we demonstrate that modest amounts of water addition (1-10%) to ethaline are of little concern for practical use and can even lead to performance improvements, such as accelerated relaxation and solvation. In contrast, very small amounts of <1% of water lead to additional slowing of the solvent response. Thus, we suggest that the attempt to dry ethaline below 1% moisture is rather counter-productive if one attempts to achieve effective solvation and charge transport properties from DESs. This study investigates the effect of water content on the diffusional relaxation dynamics of ethaline. A set of independent spectroscopic experiments and computational simulations are aimed to provide insight into the solvent response of the DES system using femtosecond time-resolved absorption spectroscopy (fs-TA), broadband dielectric spectroscopy (BDS), nuclear magnetic resonance (NMR) diffusometry and broadband relaxometry, and molecular dynamics simulations (MDS) on ethaline with 0, 0.1, 1, 10, and 28.5wt% added water. For dry ethaline, we identify choline chloride as the rate-limiting solvation component in ethaline. However, the role of the solvent components changes gradually as water is added. Further, we provide quantitative solvent relaxation rates using the different presented time-resolved spectroscopic techniques and find remarkable agreement between them. Based on the solvent relaxation rates and combined with MDS, we develop a molecular understanding of the individual solvent components and their interactions in dry and wet ethaline with varying amounts of water content.

25 ENERGY STORAGE↗
DOE OSTI2020

Effects of Ion Size and Dielectric Constant on Ion Transport and Transference Number in Polymer Electrolytes

Salt-doped polymers without added solvents have potential as nonflammable, robust electrolytes for batteries but suffer from low ion conductivity. Using bulky anions with delocalized charge may reduce ion agglomeration and increase conduction. However, size asymmetry between ions may increase preferential solvation of cations versus the larger anions, lowering the transference number t + (fraction of conductivity contributed by the cation, relevant to battery performance). We use coarse-grained molecular dynamics simulations, including a 1/r 4 potential to capture size-dependent solvation effects, to relate polymer and ion chemistry to t + and overall conductivity. At low ion size disparity, increasing dielectric constant improves cation conduction due to the mitigation of ion aggregation and correlated cation-anion motion. However, at high ion size disparity, high dielectric medium results in strong preferential solvation of cations, reducing cation mobility and t + . The trade-off between better cation-anion separation and cation preferential solvation suggests that the strategy of developing high dielectric polymers may enhance performance only at low ion size disparity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Mapping Structure and Rheology of pH-Responsive Resins for Low-VOC Coatings

In recent years, the paint and coatings industry has shifted away from traditional resin formulations that require high concentrations of volatile organic compounds (VOCs) to achieve the desired rheological performance and sustainability targets. One approach to eliminate or reduce VOCs in paint and coating formulations while maintaining the final performance is to disperse stimuli-responsive polymer latex particles in water. The chemistry and architecture of these particles have been engineered such that the suspension rheology changes in response to the pH changes. The particles can also be swollen with organic solvents to illicit similar rheological changes. To understand how the particle microstructure influences the observed macroscopic properties, we use small-angle neutron scattering and dynamic light scattering to determine that these particles consist of a cross-linked core with long polymer tails that extend into the dispersing medium. Carboxylic acid groups present on the tails deprotonate with increasing pH, and the extension of the polymer chain due to charge repulsion increases the hydrodynamic drag on the particle. Here we find that adjusting the pH alone has a much more significant effect on the shear dependence of the viscosity of the studied resin than adding organic solvent alone. We also find that this resin architecture is more responsive per mole of pH-responsive group than other architectures of pH-responsive latex particles in the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Shifting Defect Self-Regulation via Disordered Vacancies in Hollow Tin Perovskites

Tin(II)-based hybrid halide perovskites typically suffer from severe self-doping behavior as a result of facile oxidation of Sn(II) to Sn(IV), leading to high carrier densities (holes) and metallic-like conductivities that limit their applications. In this contribution, we describe how substituting the large ethylenediammonium cation for methylammonium in the intentionally defective “hollow” perovskite family, MA 1−x en x Sn 1−0.7x I 3−0.4x (MA = methylammonium, en = ethylenediammonium), where 0 ≤ x ≤ 0.38, effectively minimizes the intrinsic self-doping behavior. The use of a solvent-free, mechanochemical synthesis route further circumvents oxidative side reactions typical in solution processing, enabling more precise control and understanding of both composition and defect chemistry. Dark and time-resolved microwave conductivity measurements of these materials as a function of “x” reveal two regimes of conductivity suppression: at low x incorporation (x ≤ 0.15), the carrier density decreases by an order of magnitude via defect-mediated charge compensation, while higher substitution (0.15 < x ≤ 0.38) greatly reduces the carrier mobility. At these lower substitution levels, the observations suggest that intrinsic equilibrium tin vacancies are compensated instead by ionic defects in lieu of mobile holes. For the higher substitution levels, the less mobile carriers exhibit long recombination lifetimes, consistent with polaron-mediated transport. These findings establish a strategy for relatively low iodine chemical potential synthesis and defect-driven control of the carrier concentration in tin halide perovskites, advancing the rational discovery of dopable hybrid semiconductors.

36 MATERIALS SCIENCE↗