Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SiO2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Leveling coatings for reducing the atomic oxygen defect density in protected graphite fiber epoxy composites

Pinholes or other defect sites in a protective oxide coating provide pathways for atomic oxygen in low Earth orbit to reach underlying material. One concept for enhancing the lifetime of materials in low Earth orbits is to apply a leveling coating to the material prior to applying any reflective and protective coatings. Using a surface tension leveling coating concept, a low viscosity epoxy was applied to the surface of several composite coupons. A protective layer of 1000 A of SiO2 was deposited on top of the leveling coating, and the coupons were exposed to an atomic oxygen environment in a plasma asher. Pinhole populations per unit area were estimated by counting the number of undercut sites observed by scanning electron microscopy. Defect density values of 180,000 defects/sq cm were reduced to about 1000 defects/sq cm as a result of the applied leveling coating. These improvements occur at a mass penalty of about 2.5 mg/sq cm.

Jaworske, D. A.↗
NASA NTRS1992

Leveling coatings for reducing the atomic oxygen defect density in protected graphite fiber epoxy composites

Pinholes or other defect sites in a protective oxide coating provide pathways for atomic oxygen in low Earth orbit to reach underlying material. One concept of enhancing the lifetime of materials in low Earth orbit is to apply a leveling coating to the material prior to applying any reflective and protective coatings. Using a surface tension leveling coating concept, a low viscosity epoxy was applied to the surface of several composite coupons. A protective layer of 1000 A of SiO2 was deposited on top of the leveling coating, and the coupons were exposed to an atomic oxygen environment in a plasma asher. Pinhole populations per unit area were estimated by counting the number of undercut sites observed by scanning electron microscopy. Defect density values of 180,000 defects/sq cm were reduced to about 1000 defects/sq cm as a result of the applied leveling coating. These improvements occur at a mass penalty of about 2.5 mg/sq cm.

Jaworske, D. A.↗
NASA NTRS1992

Geochemistry of HASP, VLT, and other glasses from double drive tube 79001/2

The Apollo 17 double drive tube 79001/2 (station 9, Van Serg Crater) is distinctive because of its extreme maturity, abundance, and variety of glass clasts. It contains mare glasses of both high Ti and very low Ti (VLT) compositions, and highland glasses of all compositions common in lunar regolith samples: highland basalt (feldspathic; Al2O3 greater than 23 wt percent), KREEP (Al2O3 less than 23 wt percent, K2O greater than 0.25 wt percent), and low-K Fra Mauro (LKFM; Al2O3 less than 23 wt percent, K2O less than 0.25 wt percent). It also contains rare specimens of high-alumina, silica-poor (HASP), and ultra Mg glasses. HASP glasses contain insufficient SiO2 to permit the calculation of a standard norm, and are thought to be the product of volatilization during impact melting. They have been studied by electron microprobe major-element analysis techniques but have not previously been analyzed for trace elements. The samples analyzed for this study were polished grain mounts of the 90-160 micron fraction of four sieved samples from the 79001/2 core (depth range 2.3-11.5 cm). A total of 80 glasses were analyzed by SEM/EDS and electron microprobe, and a subset of 33 of the glasses, representing a wide range of compositional types, was chosen for high-sensitivity INAA. A microdrilling device removed disks (mostly 50-100 micron diameter, weighing approx. 0.1-0.5 micro-g) for INAA. Preliminary data reported here are based only on short counts done within two weeks of irradiation.

Lindstrom, D. J.↗
NASA NTRS1992

Sliding durability of candidate seal fiber materials in hydrogen from 25 to 900 C

Sliding durability studies of candidate ceramic fibers were conducted in hydrogen to support the high temperature seal development program at NASA LeRC. Pin-on-disk tests were used to measure the friction and durability of a tow or bundle of ceramic fibers in sliding against a superalloy disk. This procedure was used previously to test candidate fibers in an air environment. The fibers based upon mullite (Al2O3-SiO2) chemistry (Nextel 550, 440, and 312) exhibited better durability in hydrogen than in air. HPZ, a complex silicon carboxynitride fiber which showed good durabilty in air, however, showed a significant loss of durability in hot hydrogen. These results are consistent with recent thermodynamic and experimental studies of ceramic compatibility with hydrogen at elevated temperatures. These research results indicate that only oxide fibers display good durability in both air and hydrogen environments. Also, simple, low cost testing in air can provide an adequate data base for initial seal material screening and selection, especially for oxide fiber candidates. The findings of this research provide critical input to the seal design team.

Dellacorte, Christopher↗
NASA NTRS1992

On the weathering of Martian igneous rocks

Besides the young crystallization age, one of the first arguments for the martian origin of shergottite, nakhlite, and chassignite (SNC) meteorites came from the chemical similarity of the meteorite Shergotty and the martian soil as measured by Viking XRF analyses. In the meantime, the discovery of trapped rare gas and nitrogen components with element and isotope ratios closely matching the highly characteristic ratios of the Mars atmosphere in the shock glasses of shergottite EETA79001 was further striking evidence that the SNC's are martian surface rocks. The martian soil composition as derived from the Viking mission, with its extremely high S and Cl concentrations, was interpreted as weathering products of mafic igneous rocks. The low SiO2 content and the low abundance of K and other trace elements in the martian soils point to a mafic crust with a considerably smaller degree of fractionation compared to the terrestrial crust. However, the chemical evolution of the martian regolith and soil in respect to surface reaction with the planetary atmosphere or hydrosphere is poorly understood. A critical point in this respect is that the geochemical evidence as derived from the SNC meteorites suggests that Mars is a very dry planet that should have lost almost all its initially large water inventory during its accretion.

Dreibus, G.↗
NASA NTRS1992

The effect of oxygen fugacity on the partitioning of nickel and cobalt between olivine, silicate melt, and metal

The effect of oxygen fugacity, f(O2), on the partitioning behavior of Ni and Co between olivine, silicate melt, and metal was investigated in the CaO-MgO-Al2O3-SiO2-FeO-Na2O system, an analogue of a chondrule composition from an ordinary chondrite. The conditions were 1350 C and 1 atm, with values of f(O2) varying between 10 exp -5.5 and 10 exp -12.6 atm (i.e., the f(O2) range relevant for crystal/liquid processes in terrestrial planets and meteorite parent bodies). Results of chemical analysis showed that the values of the Ni and Co partitioning coefficients begin to decrease at values of f(O2) that are about 3.9 log units below the nickel-nickel oxide and cobalt-cobalt oxide buffers, respectively, near the metal saturation for the chondrule analogue composition.

Ehlers, Karin↗
NASA NTRS1993

Automated measurement of polarized bidirectional reflectance

An Automated Bidirectional Reflection Acquisition Measurement System (ABRAMS) has been constructed to facilitate measurement of bidirectional reflectance from soil and vegetative samples in the laboratory. The system illuminates a sample with linearly-polarized laser light, lambda = 632.8 nm, and measures the like- and cross-polarized scattered intensities over half a hemisphere. System design and polarized bidirectional reflectance measurements from a soil sample and SiO2 spherical particles are discussed in this work. It is shown that polarization information in the plane of incidence is useful for identifying certain scattering mechanisms associated with soil reflectance. This is because the like-polarized intensity, Ivv, is influenced by single-scattered light and the cross-polarized intensity, IHv, is strongly influenced by multiple-scattered light. For example, comparable levels of Ivv and IHv indicated that the reflectance of soils, is dominated by significant multiple scattering because single scattering causes minimal depolarization in the plane of incidence.

Gibbs, Daniel P.↗
NASA NTRS1993

Sliding wear of self-mated Al2O3-SiC whisker-reinforced composites at 23-1200 C

Microstructural changes occurring during sliding wear of self-mated Al2O3 SiC whisker-reinforced composites were studied using optical, scanning electron microscopy and transmission electron microscopy. Pin-on-disc specimens were slid in air at 2.7 m/s sliding velocity under a 26.5 N load for 1 h. Wear tests were conducted at 23, 600, 800 and 1200 C. Mild wear with a wear factor of 2.4 x 10 exp -7 - 1.5 x 10 exp -6 cu mm /N per m was experienced at all test temperatures. The composite showed evidence of wear by fatigue mechanisms at 800 C and below. Tribochemical reaction (SiC oxidation and reaction of SiO2 and Al2O3) leads to intergranular failure at 1200 C. Distinct microstructural differences existing at each test temperature are reported.

Farmer, S. C.↗
NASA NTRS1993

Mechanism of incipient oxidation of bulk chemical vapor deposited Si3N4

X-ray photoelectron spectroscopy was employed, in conjunction with ion bombardment, to analyze the chemical composition profile across thin (less than 50 nm) oxide films on chemically vapor deposited Si3N4. The thermal oxides were grown in dry oxygen at 1100 C on samples with or without native oxide film (formed in room air). The results show that the thermal oxidation product was silicon oxynitride of graded N:O ratio, and that the presence of a native oxide film promotes the formation of a SiO2 crust over the oxynitride. It is proposed that the fundamental mechanism of Si3N4 oxidation is progressive O-for-N substitution in the silicon oxynitride unit tetrahedron, which is best designated SiN(2-x)O(2+x), where x is also an index of depth. The corresponding equation for nonstoichiometric oxidation of Si3N4 describes a bulk (rather than an interface) reaction process, with significant implications for O2 and N2 fluxes and diffusivities.

Ogbuji, L. U. T.↗
NASA NTRS1993

Low resistance silver contacts to indium phosphide - Electrical and metallurgical considerations

The electrical and metallurgical behavior of the Ag-InP contact system has been investigated. Specific contact resistivity (Rc) values in the low 10 exp -6 Ohm sq cm range are readily achieved on n-InP (Si: 1.7 x 10 exp 18/cu cm) after sintering at 400 C for several minutes. The low Rc values, however, are shown to be accompanied by dissolution of InP into the metallization, resulting in device degradation. An analysis of the sinter-induced metallurgical interactions shows this system to be similar to the well-characterized Au-InP system, albeit with fundamental differences. The similarities include the dissociative diffusion of In, the reaction-suppressing effect of SiO2 capping, and especially, the formation of a phosphide layer at the metal-InP interface. The low post-sinter Rc values in the Ag-InP system may be due to the presence of a AgP2 layer at the metal-InP interface; low values of Rc can be achieved without incurring device degrading metallurgical interactions by introducing a thin AgP2 layer between the InP and the current carrying metallization.

Weizer, Victor G.↗
NASA NTRS1992

Probing hot-carrier transport and elastic scattering using ballistic-electron-emission microscopy

Ballistic-electron-emission microscopy (BEEM) has been used to characterize electron transport and scattering in metal/semiconductor structures. A SiO2 layer at the Au/Si interface was patterned to form transmitting and nontransmitting regions. By analyzing the BEEM current profiles at the boundaries of these regions, information on the spatial distribution of electrons after transport through the Au layer can be derived. A detailed comparison is made between the results presented here and models which involve modification of the electron distribution by scattering.

Milliken, A. M.↗
NASA NTRS1992

Optical fiber voltage sensors for broad temperature ranges

We describe the development of an optical fiber ac voltage sensor for aircraft and spacecraft applications. Among the most difficult specifications to meet for this application is a temperature stability of +/- 1 percent from -65 C to +125 C. This stability requires a careful selection of materials, components, and optical configuration with further compensation using an optical-fiber temperature sensor located near the sensing element. The sensor is a polarimetric design, based on the linear electro-optic effect in bulk Bi4Ge3O12. The temperature sensor is also polarimetric, based on the temperature dependence of the birefringence of bulk SiO2. The temperature sensor output is used to automatically adjust the calibration of the instrument.

Rose, A. H.↗
NASA NTRS1992

The Chemistry of Saudi Arabian Sand - A Deposition Problem on Helicopter Turbine Airfoils

Operations in the Persian Gulf have exposed military helicopter turbines to excessive amounts of ingested sand. Fine particles, less than 10 microns, are able to bypass the particle separators and enter the cooling and combustion systems. The initial sand chemistry varies by location, but is made up of a calcium aluminum silicate glass, SiO2 low quartz, (Ca,Mg)CO3 dolomite, CaCO3 calcite, and occasionally NaCl rocksalt. The sand reacts in the hot combustion gases and deposits onto the turbine vanes as CaSO4, glass, and various crystalline silicates. Deposits up to 5 mm thick have been collected. Although cooling hole plugging is a considerable problem, excessive corrosion is not commonly observed due to the high melting point of CaSO4.

Smialek, James L.↗
NASA NTRS1993

The stability of hibonite and other aluminous phases in silicate melts: Implications for the origin of hibonite-bearing inclusions

Phase fields in which hibonite (Hib) and silicate melt coexist with spinel (Sp), CaAl4O7 (CA2), gehlenitic melilite (Mel), anorthite (An), or corundum (Cor) in the system CaO-MgO-Al203-SiO2-TiO2 (CMAST) were determined and activity models developed for Mel and Hib solid solutions. Experimentally determined partition coefficients for Ti between Hib and coexisting melt, D sub t, vary from 0.8 to 2.1 and generally decrease with increasing TiO2 content in the liquid (L). Based on Ti partioning between Hib and melt, bulk inclusion compositions and Hib-saturated liquid use phase diagrams, the Hib in Fluffy Type A inclusions (FTA's) from Allende and at least some of the Hib from Hib-rich inclusions is relict; much of the Hib from Hib-glass spherules probably crystallized from a melt under nonequilibrium conditions. Bulk compositions for all of these Ca-Al-rich inclusions (CAI's) are consistent with an origin as Mel + Hib + Sp + perovskite (Pv) proto-inclusions in which Mel was partially altered. In some cases, the proto-inclusion was partially or completely melted with vaporization occurring over a period of time sufficient to remove any Na introduced by the alteration process but frequently insufficient to dissolve all of the original hibonite. If equilibration temperatures based on Hib-bearing CAI's reflect condensation in a cooling gas of solar composition, then Hib + Cor condensed at approximately 1260 C (referenced to 10 exp -3 atm) and Hib + Sp + Mel at approximately 1215 +/- 10 C. Simple thermochemical models for the substitution of trace elements into the Ca-site of meteoritic Hib suggest that virtually all Eu is divalent in early condensate Hibs but that Eu(2+)/Eu(3+) decreases by a factor of 20 or more during the course of condensation, primarily because the ratio is proportional to the partial pressure of Al, which decreases dramatically as aluminous phases condense. The relative sizes of Eu and Yb anomalies in meteoritic Hibs and CAI's may be influenced by this effect.

Beckett, J. R.↗
NASA NTRS1993

Development of a molecular beam technique to study early solar system silicon reactions

Silicon monoxide is one of the major gas phase silicon bearing components observed in astronomical environments. Silicon oxide serves as the major rock forming material for terrestrial and meteoritic bodies. It is known that several gas phase reactions produce mass independent isotopic fractionations which possess the same delta(O-17)/delta(O-18) ratio observed in Allende inclusions. The general symmetry dependence of the chemically produced mass independent isotopic fractionation process suggests that there are several plausible reactions which could occur in the early solar system which may lead to production of the observed meteoritic oxygen isotopic anomalies. An important component in exploring the role of such processes is the need to experimentally determine the isotopic fractionations for specific reactions of relevance to the early solar system. It has already been demonstrated that atomic oxygen reaction with CO, a major nebular oxygen bearing species, produces a large (approximately 90 percent), mass independent isotopic fractionation. The next hurdle regarding assessing the involvement of symmetry dependent isotopic fractionation processes in the pre-solar nebula is to determine isotopic fractionation factors associated with gas phase reactions of metallic oxides. In particular, a reaction such as O + SiO yields SiO2 is a plausible nebular reaction which could produce a delta(O-17) is approximately delta(O-18) fractionation based upon molecular symmetry considerations. While the isotopic fractionations during silicate evaporation and condensation have been determined, there are no isotopic studies of controlled, gas phase nucleation processes. In order to carefully control the reaction kinetics, a molecular beam apparatus has been constructed. This system produces a supersonic, collimated beam of SiO molecules which is reacted with a second beam of oxygen atoms. An important feature of molecular beams is that they operate at sufficiently low pressures and high temperatures in the jet that avalanche nucleation and clustering processes may be avoided.

Dong, Q. W.↗
NASA NTRS1993

The group A3 chondrules of Krymka: Further evidence for major evaporative loss during the formation of chondrules

Like Semarkona (type 3.0), Krymka (type 3.1) contains two distinct types of chondrule (namely groups A and B) which differ in their bulk compositions, phase compositions, and CL properties. The group A chondrules in both meteorites show evidence for major loss of material by evaporation(i.e. elemental abundance patterns, size, redox state, olivine-pyroxene abundances). Group A and B chondrules probably formed from common or very similar precursors by the same processes acting with different intensities, group A suffering greater mass-loss by evaporation and reduction of FeO and SiO2. While Krymka chondrules share many primary mineralogical and compositional properties with Semarkona chondrules, the minimal metamorphism it has suffered has also had a significant effect on its chondrules.

Huang, S.↗
NASA NTRS1993

Attenuation of epsilon(sub eff) of coplanar waveguide transmission lines on silicon substrates

Attenuation and epsilon(sub eff) of Coplanar Waveguide (CPW) transmission lines were measured on Silicon substrates with resistivities ranging from 400 to greater than 30,000 ohm-cm, that have a 1000 angstrom coating of SiO2. Both attenuation and epsilon(sub eff) are given over the frequency range 5 to 40 GHz for various strip and slot widths. These measured values are also compared to the theoretical values.

Taub, Susan R.↗
NASA NTRS1986

C.A.D. representation of ternary and quaternary phase diagrams

This work is concerned with the utilization of C.A.D. solid-modeling software for the computer representation of three-dimensional phase diagrams. The work was undertaken in two parts. First, the C.A.D. software (I-DEAS, by Structural Dynamics Research Corp.) was integrated with a variety of auxiliary Fortran 77 and I-DEAS language programs which were written specifically for the purpose of phase diagram representation. The capabilities of the resulting suite of software for three-dimensional phase diagram representation were developed and illustrated by the construction, display and manipulation of solid-model phase diagrams for a hypothetical quaternary eutectic system. The results of this work are discussed in some detail in the attached publication ('Solid-modeling: a C.A.D. Alternative for Three-dimensional Phase Diagram Representation'). Such a technique is of general applicability, having utility in both research and education. Secondly, using the C.A.D. technique, data from the literature (gleaned from some 70 separate publications), which represent experimentally determined phase boundaries, were combined to form solid-model representations of the CMS2-M2S-S ternary space diagram and the CMS2-CAS2-M2S-S quaternary liquidus projection (where C=CaO, M=MgO, A=Al2O3, and S=SiO2). These diagrams were utilized in a concurrent study of solidification in the CMAS system.

Delao, James D.↗