Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Repeat”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Model-scale sound propagation experiment

The results of a scale model propagation experiment to investigate grazing propagation above a finite impedance boundary are reported. In the experiment, a 20 x 25 ft ground plane was installed in an anechoic chamber. Propagation tests were performed over the plywood surface of the ground plane and with the ground plane covered with felt, styrofoam, and fiberboard. Tests were performed with discrete tones in the frequency range of 10 to 15 kHz. The acoustic source and microphones varied in height above the test surface from flush to 6 in. Microphones were located in a linear array up to 18 ft from the source. A preliminary experiment using the same ground plane, but only testing the plywood and felt surfaces was performed. The results of this first experiment were encouraging, but data variability and repeatability were poor, particularly, for the felt surface, making comparisons with theoretical predictions difficult. In the main experiment the sound source, microphones, microphone positioning, data acquisition, quality of the anechoic chamber, and environmental control of the anechoic chamber were improved. High-quality, repeatable acoustic data were measured in the main experiment for all four test surfaces. Comparisons with predictions are good, but limited by uncertainties of the impedance values of the test surfaces.

Willshire, William L., Jr.↗
NASA NTRS1987

Measurements of propeller noise in a light turboprop airplane

In-flight acoustic measurements have been made on the exterior and interior of a twin-engined turboprop airplane under controlled conditions to study data repeatability. It is found that the variability of the harmonic sound pressure levels in the cabin is greater than that for the exterior sound pressure levels, typical values for the standard deviation being +2.0 dB and -4.2 dB for the interior, versus +1.4 dB and -2.3 dB for the exterior. When insertion losses are determined for acoustic treatments in the cabin, the standard deviations of the data are typically + or - 6.5 dB. It is concluded that additional factors, such as accurate and repeatable selection of relative phase between propellers, controlled cabin-air-temperatures, installation of baseline acoustic absorption, and measurement of aircraft attitude, should be considered in order to reduce uncertainty in the measured data.

Wilby, J. F.↗
NASA NTRS1987

Brain cholinergic involvement during the rapid development of tolerance to morphine

The effect of repeated administration of morphine on the activities of the cholinergic enzymes, choline acetyltransferase (ChAT) and acetylcholinesterase (AChE), in specific brain regions were studied in rats treated with 10 mg/kg morphine for one or two days. Repeated administration of morphine was associated with a decline in the degree of analgesia produced and with a significant increase of AChE activity of the medulla oblongata. A single injection of morphine resulted in a significant decline in ChAT activity in the hypothalamus, cerebellum, and medulla oblongata regions. After two consecutive injections, no decline in ChAT was observed in these regions, while in the cerebral cortex the second administration elicited a significant decline. The results suggest that the development of tolerance to morphine may be mediated through changes in ChAT activity and lend support to the involvement of the central cholinergic system in narcotic tolerance.

Wahba, Z. Z.↗
NASA NTRS1988

Dispersion, damping and confinement of propagating pulses in large space structures

Pulse propagations in large space structures caused by repeated pulse excitations are studied analytically (by using the Z-transforms) and numerically. It is found that resonance regimes can be generated not only by periodical, but also by non-periodical repeated pulses; the conditions for such regimes are derived. Special attention is paid to the dispersion of propagating pulses due to structural irregularities, to damping of pulses due to appropriate combination of elastic and viscous properties of joints between structural members, and to the protection of certain areas of Large Space Structures (LSS) from impacts provided by a pulse trapping effect.

Zak, Michail↗
NASA NTRS1987

Performance analysis of an optimal file transfer protocol for integrated mobile satellite services

A file-transfer protocol based on the selective-repeat automatic-retransmission-request (ARQ) scheme has been developed for the Mobile Satellite Experiment (MSAT-X). In this protocol, each file is divided into packets, which are error-detected and acknowledge individually. A file can be transferred in either the open- or closed-end connection. In the open-end connection, the file is transmitted continuously according to the selective-repeat scheme until all packets are positively acknowledged; in the closed-end connection, each retransmission will initiate its own connection request. The relationship between the packet size and the average end-to-end delay in the mobile fading environment is investigated. The communications channel uses trellis-coded modulation with symbol interleaving, packet replication, and error detection. The packet error performance in such a channel is evaluated by simulation, and the optimal packet size for various operating conditions is derived, using the simulated results. It is shown that for a symbol-energy-to-noise ratio of 12 dB, each file should be divided into packets of length between 256 bits and 512 bits (excluding the overhead) to minimize the average end-to-end delay.

Wang, Charles C.↗
NASA NTRS1988

Recent developments in structural sensitivity analysis

Recent developments are reviewed in two major areas of structural sensitivity analysis: sensitivity of static and transient response; and sensitivity of vibration and buckling eigenproblems. Recent developments from the standpoint of computational cost, accuracy, and ease of implementation are presented. In the area of static response, current interest is focused on sensitivity to shape variation and sensitivity of nonlinear response. Two general approaches are used for computing sensitivities: differentiation of the continuum equations followed by discretization, and the reverse approach of discretization followed by differentiation. It is shown that the choice of methods has important accuracy and implementation implications. In the area of eigenproblem sensitivity, there is a great deal of interest and significant progress in sensitivity of problems with repeated eigenvalues. In addition to reviewing recent contributions in this area, the paper raises the issue of differentiability and continuity associated with the occurrence of repeated eigenvalues.

Haftka, Raphael T.↗
NASA NTRS1989

Determination of longitudinal aerodynamic derivatives using flight data from an icing research aircraft

A flight test was performed with the NASA Lewis Research Center's DH-6 icing research aircraft. The purpose was to employ a flight test procedure and data analysis method, to determine the accuracy with which the effects of ice on aircraft stability and control could be measured. For simplicity, flight testing was restricted to the short period longitudinal mode. Two flights were flown in a clean (baseline) configuration, and two flights were flown with simulated horizontal tail ice. Forty-five repeat doublet maneuvers were performed in each of four test configurations, at a given trim speed, to determine the ensemble variation of the estimated stability and control derivatives. Additional maneuvers were also performed in each configuration, to determine the variation in the longitudinal derivative estimates over a wide range of trim speeds. Stability and control derivatives were estimated by a Modified Stepwise Regression (MSR) technique. A measure of the confidence in the derivative estimates was obtained by comparing the standard error for the ensemble of repeat maneuvers, to the average of the estimated standard errors predicted by the MSR program. A multiplicative relationship was determined between the ensemble standard error, and the averaged program standard errors. In addition, a 95 percent confidence interval analysis was performed for the elevator effectiveness estimates, C sub m sub delta e. This analysis identified the speed range where changes in C sub m sub delta e could be attributed to icing effects. The magnitude of icing effects on the derivative estimates were strongly dependent on flight speed and aircraft wing flap configuration. With wing flaps up, the estimated derivatives were degraded most at lower speeds corresponding to that configuration. With wing flaps extended to 10 degrees, the estimated derivatives were degraded most at the higher corresponding speeds. The effects of icing on the changes in longitudinal stability and control derivatives were adequately determined by the flight test procedure and the MSR analysis method discussed herein.

Ranaudo, R. J.↗
NASA NTRS1989

Universal test fixture for monolithic mm-wave integrated circuits calibrated with an augmented TRD algorithm

The design and evaluation of a novel fixturing technique for characterizing millimeter wave solid state devices is presented. The technique utilizes a cosine-tapered ridge guide fixture and a one-tier de-embedding procedure to produce accurate and repeatable device level data. Advanced features of this technique include nondestructive testing, full waveguide bandwidth operation, universality of application, and rapid, yet repeatable, chip-level characterization. In addition, only one set of calibration standards is required regardless of the device geometry.

Romanofsky, Robert R.↗
NASA NTRS1988

Precision GPS orbit determination strategies for an earth orbiter and geodetic tracking system

Data from two 1985 GPS field tests were processed and precise GPS orbits were determined. With a combined carrier phase and pseudorange, the 1314-km repeatability improves substantially to 5 parts in 10 to the 9th (0.6 cm) in the north and 2 parts in 10 to the 8th (2-3 cm) in the other components. To achieve these levels of repeatability and accuracy, it is necessary to fine-tune the GPS solar radiation coefficients and ground station zenith tropospheric delays.

Lichten, Stephen M.↗
NASA NTRS1989

Determination of longitudinal aerodynamic derivatives using flight data from an icing research aircraft

A flight test was performed with the NASA Lewis Research Center's DH-6 icing research aircraft. The purpose was to employ a flight test procedure and data analysis method, to determine the accuracy with which the effects of ice on aircraft stability and control could be measured. For simplicity, flight testing was restricted to the short period longitudinal mode. Two flights were flown in a clean (baseline) configuration, and two flights were flown with simulated horizontal tail ice. Forty-five repeat doublet maneuvers were performed in each of four test configurations, at a given trim speed, to determine the ensemble variation of the estimated stability and control derivatives. Additional maneuvers were also performed in each configuration, to determine the variation in the longitudinal derivative estimates over a wide range of trim speeds. Stability and control derivatives were estimated by a Modified Stepwise Regression (MSR) technique. A measure of the confidence in the derivative estimates was obtained by comparing the standard error for the ensemble of repeat maneuvers, to the average of the estimated standard errors predicted by the MSR program. A multiplicative relationship was determined between the ensemble standard error, and the averaged program standard errors. In addition, a 95 percent confidence interval analysis was performed for the elevator effectiveness estimates, C sub m sub delta e. This analysis identified the speed range where changes in C sub m sub delta e could be attributed to icing effects. The magnitude of icing effects on the derivative estimates were strongly dependent on flight speed and aircraft wing flap configuration. With wing flaps up, the estimated derivatives were degraded most at lower speeds corresponding to that configuration. With wing flaps extended to 10 degrees, the estimated derivatives were degraded most at the higher corresponding speeds. The effects of icing on the changes in longitudinal stability and control derivat

Ranaudo, R. J.↗
NASA NTRS1989

GPS-based system for satellite tracking and geodesy

High-performance receivers and data processing systems developed for GPS are reviewed. The GPS Inferred Positioning System (GIPSY) and the Orbiter Analysis and Simulation Software (OASIS) are described. The OASIS software is used to assess GPS system performance using GIPSY for data processing. Consideration is given to parameter estimation for multiday arcs, orbit repeatability, orbit prediction, daily baseline repeatability, agreement with VLBI, and ambiguity resolution. Also, the dual-frequency Rogue receiver, which can track up to eight GPS satellites simultaneously, is discussed.

Bertiger, Willy I.↗
NASA NTRS1989

Adaptation to vection-induced symptoms of motion sickness

The effects of repeated exposures to a rotating circular vection drum on the symptoms of motion sickness and tachygastria in humans were investigated. Subjects were sitting in a drum and were exposed to 15 min baseline (no rotation), followed by 15 min drum rotation at 60 deg/s, and, then, by 15 min recovery. Gastric myoelectric activity was continuously recorded with the electrogastrogram. Subjects who were exposed to the drum three times with intervals of 4-24 days all showed symptoms of tachygastria and failed to show an amelioration of motion sickness symptoms. On the other hand subjects who had only 48 h between the three sessions of drum exposure, experienced a reduction in motion-sickness symptoms and in tachygastsria upon repeated exposure to the drum, indicating that training effected a symptomatic and physiological adaptation. It is suggested that preflight adaptation to visual-vestibular sensory mismatch may reduce motion sickness in astronauts.

Stern, Robert M.↗
NASA NTRS1990

Experiments and other methods for developing expertise with design of experiments in a classroom setting

The only way to gain genuine expertise in Statistical Process Control (SPC) and the design of experiments (DOX) is with repeated practice, but not on canned problems with dead data sets. Rather, one must negotiate a wide variety of problems each with its own peculiarities and its own constantly changing data. The problems should not be of the type for which there is a single, well-defined answer that can be looked up in a fraternity file or in some text. The problems should match as closely as possible the open-ended types for which there is always an abundance of uncertainty. These are the only kinds that arise in real research, whether that be basic research in academe or engineering research in industry. To gain this kind of experience, either as a professional consultant or as an industrial employee, takes years. Vast amounts of money, not to mention careers, must be put at risk. The purpose here is to outline some realistic simulation-type lab exercises that are so simple and inexpensive to run that the students can repeat them as often as desired at virtually no cost. Simulations also allow the instructor to design problems whose outcomes are as noisy as desired but still predictable within limits. Also the instructor and the students can learn a great deal more from the postmortum conducted after the exercise is completed. One never knows for sure what the true data should have been when dealing only with real life experiments. To add a bit more realism to the exercises, it is sometimes desirable to make the students pay for each experimental result from a make-believe budget allocation for the problem.

Patterson, John W.↗
NASA NTRS1990

Video camera system for locating bullet holes in targets at a ballistics tunnel

A system consisting of a single charge coupled device (CCD) video camera, computer controlled video digitizer, and software to automate the measurement was developed to measure the location of bullet holes in targets at the International Shooters Development Fund (ISDF)/NASA Ballistics Tunnel. The camera/digitizer system is a crucial component of a highly instrumented indoor 50 meter rifle range which is being constructed to support development of wind resistant, ultra match ammunition. The system was designed to take data rapidly (10 sec between shoots) and automatically with little operator intervention. The system description, measurement concept, and procedure are presented along with laboratory tests of repeatability and bias error. The long term (1 hour) repeatability of the system was found to be 4 microns (one standard deviation) at the target and the bias error was found to be less than 50 microns. An analysis of potential errors and a technique for calibration of the system are presented.

Burner, A. W.↗
NASA NTRS1990

Operational considerations for aerodynamic testing of large-scale wing sections in a simulated natural rain environment

One of the necessary areas of consideration for outdoor heavy rain testing is the effect of wind on both the simulated rain field and the quality and repeatability of the aerodynamic data. This paper discusses the data acquisition and subsequent reduction to nondimensional coefficients of lift and drag, with the appropriate correction for wind and rain field. Sample force data showing these effects are presented, along with estimates for accuracy and repeatability. The capability to produce high-quality data for rain drop size distribution using photographic and computerized image processing techniques was developed. Sample photographs depicting rain drop size are shown.

Campbell, Bryan A.↗
NASA NTRS1990

The extended tracking network and indications of baseline precision and accuracy in the North Andes

The CASA Uno Global Positioning System (GPS) experiment (January-February 1988) included an extended tracking network which covered three continents in addition to the network of scientific interest in Central and South America. The repeatability of long baselines (400-1000 km) in South America is improved by up to a factor of two in the horizontal vector baseline components by using tracking stations in the Pacific and Europe to supplement stations in North America. In every case but one, the differences between the mean solutions obtained using different tracking networks was equal to or smaller than day-to-day rms repeatabilities for the same baselines. The mean solutions obtained by using tracking stations in North America and the Pacific agreed at the 2-3 millimeter level with those using tracking stations in North America and Europe. The agreement of the extended tracking network solutions suggests that a broad distribution of tracking stations provides better geometric constraints on the satellite orbits and that solutions are not sensitive to changes in tracking network configuration when an extended network is use. A comparison of the results from the North Andes and a baseline in North America suggests that the use of a geometrically strong extended tracking network is most important when the network of interest is far from North America.

Freymueller, Jeffrey T.↗
NASA NTRS1990

Validation of the geostrophic method for estimating zonal currents at the equator from Geosat altimeter data

The applicability of satellite altimeter data for estimating zonal current variability at the equator is assessed using the meriodionally differenced form of the geostrophic balance. Estimates of geostrophic zonal flow anomalies in the equatorial Pacific have been deduced from 17-day collinear altimeter data during the first year of the Geosat Exact Repeat Mission. Altimeter-derived geostrophic estimates agree well with in situ zonal current variability. Comparison of flow-frequency near-surface zonal current observed from equatorial moorings at 165 deg E, 140 deg W, and 110 deg W yield correlations of 0.83, 0.85, and 0.51, respectively, with a mean rms difference of 23 cm/sec. The inclusion of up to 11 ascending and descending Geosat tracks within the 9-deg band for every 17-day repeat effectively reduced the temporal sampling interval to 1.5 days at 165 deg E and 140 deg W. The 6.8-km along track spacing of the altimeter measurements provides sufficient resolution for the effective filtering of small-scale meridional noise, both instrumental and oceanic.

Picaut, Joel↗
NASA NTRS1990

Continuous assimilation of simulated Geosat altimetric sea level into an eddy-resolving numerical ocean model. I - Sea level differences. II - Referenced sea level differences

The optimal interpolation method of Lorenc (1981) was used to conduct continuous assimilation of altimetric sea level differences from the simulated Geosat exact repeat mission (ERM) into a three-layer quasi-geostrophic eddy-resolving numerical ocean box model that simulates the statistics of mesoscale eddy activity in the western North Pacific. Assimilation was conducted continuously as the Geosat tracks appeared in simulated real time/space, with each track repeating every 17 days, but occurring at different times and locations within the 17-day period, as would have occurred in a realistic nowcast situation. This interpolation method was also used to conduct the assimilation of referenced altimetric sea level differences into the same model, performing the referencing of altimetric sea sevel differences by using the simulated sea level. The results of this dynamical interpolation procedure are compared with those of a statistical (i.e., optimum) interpolation procedure.

White, Warren B.↗