Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Powder”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of alloying with Sc, Nb and Zr on reduction-diffusion synthesis of magnetically hard Sm(Fe,Co,Ti) 12 -based monocrystalline powders

Powders of Sm(Fe,Co) 11.2 Ti 0.8 alloys modified with Sc, Nb and Zr, as well as with additional Ti were prepared by reducing mechanically activated raw oxides with Ca metal in the furnace preheated to 990–1250 °C. Expansion of the crystal lattice upon introduction of Nb or additional Ti implies that atoms of these elements replace the smaller Fe atoms in the tetragonal ThMn 12 -type structure. On the other hand, contraction of the lattice upon introduction of Sc or Zr was smaller than what was expected for replacement of the Sm atoms, which suggests that the Sc and Zr atoms replace both the Sm and Fe atoms. Washing away the reduction byproducts expands the crystal lattice of the 1:12 particles and increases their coercivity. The lattice expansion associated with the washing is believed to be caused by interstitial H atoms; more research, however, is needed to establish the mechanism(s) of the washing effect on the coercivity. The earlier reported development of a high coercivity in zirconium-modified monocrystalline particles achieved by increasing the reduction annealing temperature to ≈1200 °C was similarly characteristic of the particles modified with Sc (the coercivity reaches 11.5 kOe) and Nb (8.1 kOe), but not for the particles prepared with additional Ti where the maximum coercivity of 8.3 kOe develops for a lower annealing temperature. Furthermore, it is concluded that Sc, Nb and Zr modify the high-temperature phase equilibria of the Sm(Fe,Co) 11.2 Ti 0.8 alloys allowing for an effective high-temperature processing, whereas the alloy coercivity increases with the synthesis temperature through a different, still unknown mechanism which may involve suppression of the defects specific to the 1:12 crystals.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Parameter development and characterization of laser powder directed energy deposition of Nb – Alloy C103 for thin wall geometries

This work focuses on the parameter development and microstructural characterization of Nb-based alloy C103 for thin wall structures produced via laser powder – directed energy deposition (LP – DED). Laser power and scanning speeds were varied as part of a design of experiments to identify adequate print parameters. Combinations were evaluated for relative density, porosity, and geometrical accuracy. A combination of a laser power of 1420 W and scanning speed of 14 mm/s resulted in a relative density >99%, exhibited a consistent weld bead profile and was used for further microstructural evaluation. A mix of optical and scanning electron microscopy (SEM) revealed small, slightly elongated grains along the edges and large epitaxial grains in the central region along the Build – Transverse view. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analysis revealed Hf rich columnar cells in the center that transition into an evenly spaced cellular structure towards the edges of the built sample. Electron backscatter diffraction (EBSD) scans show a sharp [001] texture when looking at the cross section of the sample along the build direction. The Build – Scan view revealed a zig – zag pattern that follows the back – and – forth deposition strategy that was used. Finally, microhardness measurements were taken in the as – built (AB) and stress relieved (SR) conditions to baseline preliminary mechanical properties. The AB condition exhibited a large amount of scatter in the data and averages up to 11% larger than the SR condition. The reduction in scatter upon applying the SR cycle are indicative of a large concertation of dislocations present in the AB condition.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tensile properties of powder-metallurgical-processed tungsten alloys after neutron irradiation near recrystallization temperatures

The tensile properties of powder-metallurgical-processed Pure W, K-doped W, W-3%Re, and K-doped W-3%Re were examined after neutron irradiation up to 0.7 dpa at 910–1020 °C with a thermal neutron shield in the High Flux Isotope Reactor (HFIR). After irradiation, recrystallized Pure W (R) exhibited a brittle fracture mode, while recrystallized K-doped W-3%Re (R) exhibited a ductile fracture mode at 500 °C. K-doped W-3%Re (R) has fine grains, and hence, contains a considerable number of grain boundaries that act as sinks for irradiation defects. Solid solute Re in the W matrix could improve not only the mechanical properties of W, but also its resistance to neutron irradiation. At 500 °C, the ductility of K-doped W-3%Re after irradiation was significantly higher than that of Pure W. The irradiation at ~1000 °C did not induce hardening of stress-relieved (SR) W materials, but SR W materials tended to exhibit a decrease in the ultimate tensile strength (UTS) and an increase in total elongation (TE). Here, the softening due to the recovery and recrystallization of SR W materials and the hardening due to the formation of irradiation defect clusters were balanced during irradiation at ~1000 °C, and ductility was exhibited without an increase in strength.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Creep behavior of 316 L stainless steel manufactured by laser powder bed fusion

Additive manufacturing as a new processing technique can produce unique microstructure that is difficult to achieve using conventional techniques. Here, we have investigated the creep behavior of 316 L stainless steel produced by a laser powder bed fusion process at temperatures of 550, 600 and 650 °C and stresses between 175 and 300 MPa. We found that additively-manufactured 316 L stainless steel had a higher stress dependence of the minimum creep rate than conventionally-made Type 316 SS, which could be attributed to the dislocation cell structure resulting from the printing process. The dislocation cell structure was unstable under creep, evolving into a uniform dislocation structure under the test conditions. While internal porosity in AM 316 L SS may serve as nucleation sites of creep voids and may be responsible for a relatively lower creep life, additively-manufactured 316 SS did not show inferior creep ductility when compared with conventionally-made 316 SS. The creep life of AM 316 L SS could be improved by stabilizing dislocation cell structure and/or reducing internal porosity through an optimized additive manufacturing process.

316 L stainless steel↗
DOE OSTI2021

Deuterium permeation and retention in 316L Stainless Steel Manufactured by Laser Powder Bed Fusion

Deployment of additively manufactured materials into nuclear energy systems requires investigation of the full range of the unique environmental effects on these materials. Hydrogen isotopes are common gaseous species in nuclear reactors and exhibit ample high mobility in most materials. While hydrogen isotopes mobility in wrought stainless steel is well understood, this property is not thoroughly studied for its additively manufactured variants. In this study, we investigated the deuterium permeation and retention in 316L stainless steel manufactured by laser powder bed fusion. The results showed that the deuterium permeability in the as-built additively manufactured 316L stainless steel (AM SS316L) is greater than that of the reference wrought 316L stainless steel by a factor of 2.8. However, the stress-relieved and solution-annealed AM SS316L samples exhibit lower deuterium permeability in comparison with the as-built condition. Following the solution annealing, the deuterium permeability of AM SS316L is comparable with that of the reference wrought SS316L. Deuterium retention in the as-built AM SS316L is 45% higher than that of the wrought 316L stainless steel and slightly higher than that of the two thermally annealed AM SS316L materials. Finally, transmission electron microscopy and positron annihilation lifetime spectroscopy were used to obtain microstructural information used to determine deuterium permeation and retention behavior in the studied materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The role of cellular structure, non-equilibrium eutectic phases and precipitates on quasi-static strengthening mechanisms of as-built AlSi10Mg parts 3D printed via laser powder bed fusion

The quasi-static loading strengthening mechanism in the as-built state of an AlSi10Mg alloy 3D-printed via Laser Powder Bed Fusion (LPBF) was thoroughly identified and quantified using state-of-the-art electron microscopy and synchrotron X-ray diffraction techniques. The yield strength was comprehensively modelled through an in-depth characterization and quantification of the microstructural features as well as their effective volumes for strengthening. In particular, the non-equilibrium eutectic network was characterized with a two-fold structure: cell boundary particles as well as intracellular lamellar/fibrous networks, each consisting of discrete phases exhibiting a thru-thickness compositional gradient, a semi-coherent interface with the matrix and an abundance of crystal defects such as nano-sized sub-grains, microstrains and stacking faults. Further, these altogether made the eutectic phase the most potent contributor to the yield strength accounting for ~30–40% of the estimated value (i.e., cell boundary and eutectic network strengthening combined). Precipitates strengthening was identified as the second most potent mechanism via a shearing process only. Moreover, the presented methodology was able to capture the effect of LPBF processing variables on the individual strengthening contributions, e.g., the effect of a lower laser scanning speed on increasing the cell size as well as the mean precipitate size, which are shown to exhibit opposing impacts on strengthening.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The influence of chemical short-range order on the nanoindentation properties of high-entropy alloys prepared via laser powder bed fusion

Chemical short-range order (CSRO) plays an instrumental role in determining the mechanical properties of high-entropy alloys (HEAs). Current methods for controlling CSRO mainly focus on cast HEAs, which can not solve the problem of grain coarsening caused by homogenization treatments. Laser Powder Bed Fusion (LPBF), which has extremely high cooling rates, can suppress compositional segregation, refine grain structures, and achieve low CSRO. This offers a promising avenue for quantitatively controlling CSRO without the need for homogenization treatments. In this study, we investigate the CSRO of HEAs fabricated via LPBF and elucidate their influence on nanoindentation behavior. The results show that, at the low cooling rate, the average size of CSRO is 0.66 nm and they occupy 2.8% of the cross-sectional area, while at high cooling rate, the corresponding values are 0.92 nm and 9.9%, respectively, both of which are significantly smaller than those of cast HEAs. Furthermore, by analyzing samples with different CSROs, we observe that the hardness increases and then decreases with the increase of CSRO, primarily due to the preferential formation of dislocations in regions enriched with Cr-Mn-Ni. With the improvement of CSRO, both the size and quantity of Cr-Mn-Ni rich region gradually increased; subsequently, as multiple Cr-Mn-Ni rich regions tend to merge into one during the CSRO improvement, the size of the Cr-Mn-Ni rich region continued to increase while the quantity gradually decreased; when the size of the Cr-Mn-Ni rich region is moderate and widely dispersed, the dislocation density is higher with much more uniform distributions, which favorably improves nanoindentation hardness.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The onset of alloying in Cu-Ni powders under high-shear consolidation

Friction consolidation (FC) is a solid phase processing methodology that densifies a material through high-shear deformation and pressure at elevated temperature. The method has garnered interest in the scientific community because of its ability to produce extremely refined and homogeneous microstructures, off-axis texture development, and improved material properties. This manuscript presents an investigation of Cu and Ni material mixing via evaluation of morphological evolution, grain boundary characterization, and compositional analysis to provide insights on the operational alloying mechanisms occurring under high shear and elevated temperature. Using correlative microscopy techniques, we show alloying progresses via a combination of grain boundary diffusion and interfacial roughening at heterophane boundaries. Evidence supporting Cu infiltration along Ni-Ni grain boundaries along with asymmetric diffusion of Cu into Ni grains is highlighted. The resultant, consolidated microstructure was produced directly from a powder compact in ~30 s and exhibited a submicron, equiaxed grain size.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Surface smoothing for laser powder-bed Ti-6Al-4V by a transient liquid phase

Surface roughness is the primary driver of fatigue for additively manufactured metals. To address surface roughness, this work introduces a new method to smooth features beyond line-of-sight without material removal. The method applies a coating that triggers local surface remelting by activating a eutectic reaction during heat treatment. The associated liquid phase then wets and isothermally solidifies into a smoother surface. For Ti-6Al-4V fabricated with laser powder bed fusion, samples with and without TLP smoothing (using a Cu coating) were characterized with a suite of techniques, including mechanical testing, electron backscatter diffraction, synchrotron X-ray tomography, and fractography. TLP smoothing reduced surface roughness by 80% and amplified compressive residual stress at the surface by about 50%. With statistically equivalent virtual microstructures, crystal plasticity scrutinized the roles of phases, porosity, and surface roughness. Although the tensile strain-to-failure was reduced to 1% strain, the TLP smoothing process increased high-cycle fatigue strength by about 20% compared to control samples, pointing to future opportunities to optimize the new process through various coating compositions and heat treatment schedules. Overall, this work establishes a new paradigm for treating surfaces of materials for smoothness and compressive residual stress.

Additive manufacturing↗
DOE OSTI2025

Fatigue life prediction of powder bed fused–laser beam AlSi10Mg: Incorporating critical defects via crystal plasticity modelling

The current study provides a microstructurally-based computational framework to predict the fatigue life of additive manufactured (AM), i.e., powder bed fused–laser beam (PBF-LB), AlSi10Mg specimens using the crystal plasticity finite element method (CPFEM). The fractography analysis, electron backscatter diffraction (EBSD), uniaxial and cyclic responses, and fatigue life of specimens were used to inform the computational framework. CPFE simulation was used to compute fatigue indicator parameters (FIPs) as fatigue driving forces. A new fatigue criterion is introduced based on FIPs, which was calibrated using experimental fatigue data. The proposed fatigue measure was evaluated versus the specimens with critical defects of various sizes and locations subjected to different stress amplitudes. The results show that the developed framework can capture the fatigue life of samples with different critical defect locations and sizes along with different stress amplitudes for both high-cycle fatigue (HCF) and very high-cycle fatigue (VHCF) regimes.

Additive manufacturing↗
DOE OSTI2025

Unit cell manufacture by blown powder directed energy deposition

Lattice structures manufactured by additive manufacturing show unique promise to alter existing components to improve the thermo-mechanical properties of the base structure. Here, in the present study, the manufacture of a self-supporting lattice structure by blown powder directed energy deposition was explored. Converging struts were manufactured using multiple lean angles to facilitate the self-supporting structure and to avoid machine-part collisions. The struts showed near uniform straightness relative to a fitted line with a maximum deviation of 1mm at a lean angle of 10°. Micro–hardness and porosity evaluation results showed no significant variation along the struts.

Additive manufacturing↗
DOE OSTI2021

Fracture characteristics and heat treatment of laser powder bed fusion additively manufactured GRCop-84 copper

Laser Powder Bed Fusion (LPBF) of Glenn Research Copper 84 (GRCop-84), a Cr 2 Nb (8 at. % Cr, 4 at. % Nb) precipitation hardened alloy, produces a fully dense high conductivity alloy with a yield strength of 500 MPa and ultimate tensile strength (UTS) of 740 MPa, superior to other competing copper alloys, and 20% elongation at fracture for material stressed perpendicular to the build direction. The high thermal stability of the Cr 2 Nb precipitate in the copper matrix reduces coarsening and maintains a 300 MPa yield, 520 MPa UTS and 26% elongation after a 900 °C, 5-h heat treatment, while a 3 h 450 °C heat treatment increases yield to 810 MPa, UTS to 970 MPa with 9% elongation at fracture, for samples stressed perpendicular to the build direction. Tensile strength anisotropy based on print direction was attributed to internal stress and columnar grain formation. Void nucleation during tensile fracture was initiated by brittle fracture of precipitate particles within the copper matrix. Fracture cusps contain matching precipitate fragment geometry on opposing sides located near the cusp center in at least 80% of fracture cusps. An optimal precipitate size of 100 nm is predicted for maximum tensile strength from precipitates on fracture surfaces, while tensile testing with varying heat treatments shows maximum strength with 100 nm and smaller precipitates. Cr2Nb precipitates are shown to transition between polycrystalline and monocrystalline structures at high temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Characterization of multi-material 316L-Hastelloy X fabricated via laser powder-bed fusion

The aim of this work is to provide firsthand knowledge of 316 L stainless steel (316 L) and Hastelloy X (HX) multi-material processing via laser powder bed fusion (PBF). Specifically, microstructure of the interface is studied using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD). Surface metrology is performed to characterize the resulting surface roughness at the interface followed by tensile and flexural testing of multi-material samples to characterize the mechanical properties of the interfaces. Results showed that use of proper process parameters for each individual material led to formation of a compositional gradient at the interface that stretched for 240 μm (10–12 layers) with no evidence of cracking or porosity. The interface exhibited higher surface roughness compared to 316 L or HX as measured by arithmetic mean height, Sa, and maximum valley depth, Sv, parameters. During tensile testing, samples failed in the 316 L region away from the interface, with comparable yield strength, ultimate strength, and ductility. Finally, it was concluded that the “naturally” formed interface created a compositional gradient which was defect free due to similar values of coefficient of thermal expansion, input energy density, and different Marangoni numbers of the materials.

316L stainless Steel↗
DOE OSTI2025

Influence of post deposition annealing on the microstructural evolution and tensile behavior of austenitic stainless-steel alloy 709 made by laser powder bed fusion

Structural materials used in the next generation nuclear reactors or other advanced energy systems are often required to withstand higher operating temperatures for a longer service life. Alloy 709 (A709), a Nb-containing and N-stabilized Fe-25Ni-20Cr austenitic stainless steel, has been recommended for high-temperature reactor constructions due to the better performance over the baseline Type 316H stainless steel. Here, in the current manuscript, for the first time, the microstructure evolution and tensile behavior of an A709 made by laser powder bed fusion (LPBF) is discussed. The as deposited and heat treated LPBF alloys are compared with a reference wrought alloy. Owing to the chemical segregation and a higher number of dislocations, the LPBF materials show a significantly higher density of precipitates formed during high temperature treatments when compared to the wrought samples. This is reflected when looking at the tensile properties, both at room and elevated temperatures, where LPBF samples show higher strengths compared to wrought materials.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Microstructural evolution, defect mitigation, and precipitation behavior in AA6061 via laser powder bed fusion with high-temperature substrate heating

Defects, particularly solidification cracking, remain persistent challenges in the laser powder bed fusion (LPBF) processing of AA6061 aluminum alloy. This study systematically investigates defect mitigation, microstructural evolution, and mechanical properties associated with high-temperature substrate preheating at 500 °C. Comprehensive microstructural analyses, including characterization of defects, grain structures, and precipitation behavior, were performed on samples in both as-built and T6 heat-treated states. Elevated preheating substantially reduced solidification cracking across a wide processing window, while demonstrating decreased crack sensitivity to laser parameters. Columnar cracks along the build direction were observed despite substrate preheating. Lack-of-fusion and keyhole porosity were effectively eliminated, though gas-induced microporosity persisted at higher powers. In-depth characterization of two distinct laser power and speed conditions confirmed the formation of micron-sized, non-coherent Mg 2 Si precipitates under heated substrate conditions, alongside α-AlFeCrMnSi intermetallic phases indicative of in-situ thermal effects during fabrication. Subsequent T6 heat treatment revealed the formation of fine, coherent needle-shaped β″ strengthening precipitates. Despite substantial differences in processing parameters, comparable mechanical properties were measured in the as-built samples (∼52 MPa yield strength, ∼130 MPa tensile strength), primarily due to reduced strain hardening effects and consistent precipitation characteristics. Meanwhile, the T6 heat treatment led to significant improvement in properties, enhancing yield strength by over 400%, aligning closely with the performance of conventional wrought AA6061-T6. These findings underscore that high-temperature substrate preheating offers an effective means to suppress cracks, control precipitation, and enhance mechanical performance in LPBF-processed AA6061.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Influence of scan strategy on porosity and microstructure of Ti-6Al-4V fabricated by electron beam powder bed fusion

Ti-6Al-4V is of high value in biomedical, aerospace, and industrial sectors and is ideal for additive manufacturing (AM) because of its poor machinability. In electron beam powder bed fusion of Ti-6Al-4V, a raster scan is commonly used and often results in porosity that is detrimental to the fatigue strength. In this paper, we demonstrate that spot melting can significantly minimize porosity but produces a coarser microstructure compared to raster melting. Process parameters can be optimized to achieve minimal porosity with tailored microstructures. A finite element method was used to rationalize these observations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solidification and crystallographic texture modeling of laser powder bed fusion Ti-6Al-4V using finite difference-monte carlo method

Laser powder bed fusion (LPBF) additive manufacturing makes near-net-shaped parts with reduced material cost and time, rising as a promising technology to fabricate Ti-6Al-4V, a widely used titanium alloy in aerospace and medical industries. However, LPBF Ti-6Al-4V parts produced with 67° rotation between layers, a scan strategy commonly used to reduce microstructure and property inhomogeneity, have varying grain morphologies and weak crystallographic textures that change depending on processing parameters. Here, this study predicts LPBF Ti-6Al-4V solidification at three energy levels using a finite difference-Monte Carlo method and validates the simulations with large-area electron backscatter diffraction (EBSD) scans. The developed model accurately shows that a <001> texture forms at low energy and a <111> texture occurs at higher energies parallel to the build direction but with a lower strength than the textures observed from EBSD. A validated and well-established method of combining spatial correlation and general spherical harmonics representation of texture is developed to calculate a difference score between simulations and experiments. The quantitative comparison enables effective fine-tuning of nucleation density (N 0 ) input, which shows a nonlinear relationship with increasing energy level. Future improvements in texture prediction code and a more comprehensive study of N 0 with different energy levels will further advance the optimization of LPBF Ti-6Al-4V components. These developments contribute a novel understanding of crystallographic texture formation in LPBF Ti-6Al-4V, the development of robust model validation and calibration pipeline methodologies, and provide a platform for mechanical property prediction and process parameter optimization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Scintillation properties of diamond powders and feasibility of using them in thermal neutron detectors

Diamond offers unique properties for radiation detection, including high radiation hardness, very low gamma sensitivity, and fast response. Conventional diamond detectors rely on charge collection, but this approach requires ultra-pure single crystals and suffers from radiation-induced degradation. Here, in this work, we demonstrate an alternative approach using diamonds as scintillators for detection of charged particles and thermal neutrons. Prototypes were fabricated from commercially available diamond powders bonded to glass substrates and coupled with 6 LiF converters and silicon photomultipliers (SiPMs) and conventional PMTs. We characterized their scintillation properties under alpha particle excitation, x-ray photoluminescence, and thermal neutrons. The tryout detectors exhibit strong scintillation light signals, nanosecond-scale response times, and neutron detection efficiencies up to approximately 14 %, evaluated by comparison to conventional 3 He detector with known efficiency. These results demonstrate the feasibility of cost-effective, lightweight and robust diamond scintillation detectors for applications in space and planetary science, nuclear security, safeguards and environmental monitoring requiring efficient, robust, gamma-blind neutron detectors.

47 OTHER INSTRUMENTATION↗