SEARCH · Engineering Papers
Results for “Photoelectron spectroscopy”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Characterization of front contact degradation in monocrystalline and multicrystalline silicon photovoltaic modules following damp heat exposure
Reliability and durability tests play a key role in the photovoltaic (PV) industry by minimizing potential failure risks for both existing and new cell and module technologies. In this work, a detailed study of contact degradation in monocrystalline and multicrystalline PV modules is performed. The modules are subjected to a sequence of damp heat (DH) exposures followed by electrical characterization after each step. Electroluminescence (EL) imaging shows different darkening patterns for monocrystalline modules compared to multicrystalline modules; the former shows darkening near the busbars and the latter shows it across virtually the entire cell surface. The primary loss mechanism is confirmed to be resistive after comparing the current-voltage (I–V) characteristics at each DH exposure step. Representative samples have been cored out from both the degraded modules and controls for materials characterization to gain further insights into the degradation mechanism. Top-down and cross-sectional scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and top-down high-resolution X-ray photoelectron spectroscopy (XPS) analysis performed on the cored samples confirm the degradation is due to metallization corrosion. Our study suggests that the difference in the darkening pattern can most likely be attributed to the different silver paste composition used for contacting each cell technology, particularly the composition of the glass frit.
Understanding the Roles of the Electrode/Electrolyte Interface for Enabling Stable Li∥Sulfurized Polyacrylonitrile Batteries
Sulfurized polyacrylonitrile (SPAN) is a promising high-capacity cathode material. Here, we use spatially resolved X-ray absorption spectroscopy combined with X-ray fluorescence (XRF) microscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy to examine the structural transformation of SPAN and the critical role of a robust cathode–electrolyte interface (CEI) on the electrode. LiS x species forms during the cycling of SPAN. However, in carbonate-based electrolytes and ether-based electrolytes with LiNO 3 additives, these species are well protected by the CEI and do not dissolve into the electrolytes. In contrast, in an ether-based electrolyte without the LiNO 3 additive, LiS x species dissolve into the electrolyte, resulting in the shuttle effect and capacity loss. Examination of the Li anode by XRF and SEM reveals dense spherical Li morphology in ether-based electrolytes, but sulfur is present in the absence of the LiNO 3 additive. In contrast, porous dendritic Li is found in the carbonate electrolyte. These analyses established that an ether-based electrolyte with LiNO 3 is a superior choice that enables stable cycling of both electrodes. Based on these insights, we successfully demonstrate the stable cycling of high areal loading SPAN cathode (>6.5 mA h cm –2 ) with lean electrolyte amounts, showing promising Li∥SPAN cell performance under practical conditions.
Vapor-phase grafting of a model aminosilane compound to Al 2 O 3 , ZnO, and TiO 2 surfaces prepared by atomic layer deposition
Atomic layer deposition (ALD) is a highly versatile surface functionalization technique that can conformally coat both planar and porous substrates. Here we use ALD metal oxide layers to establish a well-defined starting surface for vapor-phase surface organic modification. Vapor-phase (3-aminopropyl)triethoxysilane (APTES) surface silanization of ALD Al 2 O 3 , ZnO and TiO 2 surfaces were studied at 100 °C, 150 °C and 200 °C. In situ quartz crystal microbalance (QCM) and Fourier-transform infrared (FTIR) spectroscopy measurements, and ex situ atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) measurements showed uniform monolayer silane formation through self-limiting APTES reaction. We observed a higher surface density of grafted APTES species following silanization at 100 °C compared to 200 °C, and we attribute this to the temperature-dependent reactivity of the surface hydroxyls and changes in the mode of APTES reaction. The FTIR and XPS measurements revealed that APTES reacts with Al 2 O 3 and ZnO exclusively through metal siloxy bond formation. However, APTES reacts with TiO 2 through both siloxy bond formation and ammonium salt formation via the amine group.
Development and characterization of an aerosol-generated multi-method analytical particle test material
Ceria (CeO 2 ) particles with low to ultra-low loading of nickel dopant were produced using an aerosol-based, droplet-to-particle synthesis via an in-line calcination technique. This aerosol-based synthesis method enables the production of particles with a monodisperse size distribution. These produced and well-characterized, multi-element, ceria-based particles demonstrate a material exemplar for multi-method analytical testing. They were prepared from a cerium nitrate feedstock where low loading nickel dopant was added at target Ni/(Ni + Ce) atomic percents of 1 %, 0.1 %, and 0.01 %, using a nickel nitrate spike. This methodology proved to produce ceria particles doped with a dynamic range of low to ultra-low loadings of nickel over a 24-h period, with consistent size distribution, morphology, and composition. The successful incorporation of nickel was demonstrated with bulk and single particle inductively coupled plasma mass spectroscopy and revealed notable particle-to-particle elemental homogeneity. X-ray photoelectron spectroscopy demonstrated the presence of a high concentration of nickel dopant incorporated preferentially toward the surface of the particles, and that this dopant aided oxidation of surface Ce(III) atoms to Ce(IV). These particle test materials were then validated through X-ray absorption near edge spectroscopy, comparing the ultra-low 0.01 % Ni and low 1 % Ni-doped ceria samples. This revealed a more-reduced oxidation state of the nickel with an increase in dopant concentration. Finally, this work demonstrates a synthesis and systematic characterization scheme to produce multi-method analytical test particulates.
Surface Nanostructure Control and Thermodynamic Stability Analysis of Femtosecond Laser-Ablated CuCoMn 1.75 NiFe 0.25 Nanoparticles
Surface nanostructure control is the key to functionalizing nanomaterials. This paper presents a characterization with thermodynamic stability analysis of CuCoMn 1.75 NiFe 0.25 high-entropy alloy (HEA) nanoparticles synthesized by femtosecond laser ablation in ethanol and liquid nitrogen (LN2). Using multimodal electron microscopy and spectroscopy, we examine phase, particle size, defect structure, chemical distribution, and surface composition and relate them to HEA stability. Elemental distributions are uniform in both media, but LN2 produces smaller particles with a narrower size distribution and mainly single- or few-domain interiors, whereas ethanol yields larger particles built from 2–4 nm crystallites with domain aggregation. Edge defects appear in both but energy-dispersive X-ray spectroscopy (EDS) is broadly uniform with local fluctuations in ethanol. X-ray photoelectron spectroscopy (XPS), supported by an attenuation model, indicates an ∼1 nm oxide overlayer that suppresses Mn 2p intensity; correcting for it returns Mn toward the bulk value. UV–NIR and photoluminescent spectra independently support a thin oxide shell. Composition-based thermodynamic descriptors place LN2 closer to bulk mixing parameters, while ethanol raises ΔH_mix and lowers Ω. Cooling simulations are consistent (LN2 ∼ 0.1 μs quench, ethanol ∼1 μs). In conclusion, these results connect solvent-controlled kinetics and thermodynamics to crystalline state and surface chemistry, informing surface control of HEA nanoparticles.
Optimizing dicyandiamide pretreatment conditions for enhanced structure and electronic properties of polymeric graphitic carbon nitride
Graphitic carbon nitride, a polymeric semiconductor, possesses a distinctive electronic band structure and exceptional chemical stability, making it a highly promising material for various catalytic applications such as electrocatalysis, photocatalysis, and photo-electrocatalysis. However, its practical applications remain limited due to its low active site density and poor electrical conductivity. In this study, to overcome such limitations, we have conducted a thorough investigation to explore the impact of dicyandiamide (DCDA) precursor pretreatment prior to thermal polymerization to graphitic carbon nitride. The DCDA precursor was subjected to various pretreatment methods including grinding using mortar and pestle, recrystallization through stirring or probe sonication after dissolving in deionized water, and freeze drying, prior to thermal polymerization at 550 °C for 2 hours. The structural and morphological properties of the catalysts prepared were compared and characterized by X-ray diffraction (XRD), attenuated total reflectance–Fourier transform infrared (ATR-IR) spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) analysis while the electronic band gap properties were determined based on density functional theory (DFT) calculations for a set of crystalline systems having C/N ratios similar to those identified experimentally. In comparison to direct thermal polymerization, pretreated samples rendered the same product yield, diverse morphologies with flat or wrinkle structures, and reduced electrochemical resistance, making them suitable for use in various catalytic processes.
Comment on “STM study of the (111) and (100) surfaces of PdAg, Surf. Sci. 417 (1998) 292–300" and references therein
Investigation of isolated, single atoms on the surfaces of alloys is of great interest in the field of heterogeneous catalysis. Prior studies by Nieuwenhuys, etal. [Surf. Sci. 417 (1998) 292–300 and references therein] showed that annealing the (111) surface of a PdAg bulk alloy yielded a surface with ~5% Pd, predominantly in the form of single atoms, rendering it an ideal model for investigating the reactivity of single Pd atoms. Herein, new evidence is reported that establishes the bulk composition of the PdAg(111) alloy studied previously is 67 % Ag and 33 % Pd, whereas it was reported to be 33 % Ag and 67 % Pd in the prior studies. Furthermore, the bulk composition of a crystal derived from the same PdAg alloy boule used previously was determined using energy-dispersive X-ray spectroscopy (EDS)—a bulk sensitive technique. Surface-sensitive measurements, including X-ray photoelectron spectroscopy, were also performed and are in good agreement with the prior studies by Nieuwenhuys, etal.
Molecular Iodine Interactions with Fe, Ni, Cr, and Stainless Steel Alloys
The adsorption behavior of molecular iodine is important for understanding the spread of radioiodine in a nuclear accident. Prior experiments indicate that, in addition to the interaction with Fe, molecular iodine [i.e., I 2(g) ] also interacts with the next most abundant components of austenitic stainless steel (i.e., Ni, and Cr) at room temperature. Here, we investigate iodine adsorption on Fe, Ni, and Cr while focusing on understanding the variables affecting adsorption as well as the iodine compounds that are formed during adsorption. Scanning electron microscopy and energy-dispersive X-ray spectroscopy were used to characterize the surfaces of exposed metal particles and aid in the understanding of the morphology and chemistry of iodine interactions with the substrates. Inductively coupled plasma optical emission spectroscopy was used to detect low levels of metal iodides and X-ray photoelectron spectroscopy was used to confirm the formation of the metal iodides. The role of environmental factors (e.g., humidity and oxygen content) for iodine adsorption on metal substrates is addressed. The individual metals demonstrated formation of metal iodides for Fe and Ni particles from interaction with I 2(g) . The formation of metal iodides may indicate the affinity of iodine for the respective metal. In this study, the iodine affinities ranked Fe > Ni > Cr as determined by the quantity of chemisorbed iodine. This trend is also supported by the distributions and proportions of metals in the corrosion product of the stainless steels. The exposures without oxygen and humidity indicate the potential of a multistep iodine adsorption process where iodine first attacks the oxide layer and then chemisorbs to the exposed metal.
Long-Term Cycling of a Mn-Rich High-Voltage Spinel Cathode by Stabilizing the Surface with a Small Dose of Iron
The high-voltage, cobalt-free spinel cathode LiNi 0.5 Mn 1.5 O 4 (LNMO) is receiving extensive attention for lithium-ion batteries due to its low cost, high operating voltage and energy density, superior power density, and good thermal stability. However, its high operating voltage hampers its stability with commercial electrolytes and makes its practical viability challenging. We present here a Mn-rich LNMO cathode to encourage the disordering of Mn and Ni in the lattice and the incorporation of a small dose of Fe into Mn-rich LNMO (Fe-LNMO) to improve the cycling stability. The introduction of Fe further increases the cation disorder between Mn and Ni, thus enabling a better rate capability. Electron energy loss spectroscopy analysis indicates that Fe is concentrated on the surface, and X-ray photoelectron spectroscopy analysis shows that Fe-LNMO alleviates the aggressive reaction between the cathode surface and the electrolyte, thus stabilizing the interface and cycle life. Furthermore, a full cell assembled with a graphite anode with an areal capacity of 3 mA h cm –2 displays a capacity retention of 90% over 300 cycles. Furthermore, the present work demonstrates an effective way to promote cation disordering and lower the surface reactivity of LNMO with the electrolyte, thereby enhancing the conductivity, stabilizing the cathode–electrolyte interphase, and making LNMO promising for practical applications.
Ultrafast Electron–Dipole Interactions in TeO- Photodetachment
We present direct experimental evidence of ultrafast coupling between ejected electrons and dynamically forming dipole moments in TeO, captured during the photodetachment of TeO?. By combining high-resolution cryogenic photoelectron spectroscopy with velocity-map imaging, we assess previously inaccessible excited states and resolve rich photoelectron angular distributions (PADs) that encode electron–dipole interactions. Systematic comparison of PADs from femtosecond and picosecond lasers reveals striking deviations from free-electron behavior, representing direct evidence of a transient dipole moment evolving on femtosecond timescales. Quantitative analysis pinpoints the dipole buildup time to be within ~60 fs, providing real-time access to the birth of a molecular dipole field. This work establishes a general approach to probing electron-dipole interactions in their formation stages, offering fundamental insights into the ultrafast interplay between departing electrons and transient polar systems — a process that lies at the core of atomic, molecular, and ultrafast physics.
Local electronic structure of histidine in aqueous solution
Here, the local electronic structure of aqueous histidine, an amino acid important in nature and biology, is revealed by aerosol X-ray photoemission spectroscopy. A detailed picture of the photoionization dynamics emerges by tuning the pH of the aqueous solution from which the aerosols are generated, allowing us to report the X-ray photoelectron spectroscopy (XPS) of histidine. Assignment of the experimental photoelectron spectra of the C1s and N1s levels allows the determination of the protonation state of histidine in these aqueous aerosols and is confirmed by density functional calculations. XPS spectra show that at pH = 1, both imidazole and amine group nitrogens are protonated, at pH = 7, the amine group nitrogen is protonated and the carboxyl group carbon is deprotonated resulting in a zwitterionic structure, and at pH = 13, only the carboxyl group remains deprotonated. Comparison of these results with previous experimental and theoretical results suggests that X-ray spectroscopy on aqueous aerosols can provide a convenient and simple way of probing their electronic structure in aqueous solutions.
Unsupported and carbon-supported silver catalysts for oxygen reduction reaction in alkaline media
Quick and easy Ag catalysts preparation via wet chemical synthesis method using only reducing agent (pure-Ag); reducing agent and citric acid as the capping agent (Ag-CA); and carbon support (KetjenBlack 600J), capping agent, and the reducing agent (Ag/C) is demonstrated. The Ag-based electrocatalysts are characterized by high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) with energy-dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM), X-ray diffraction (XRD) analysis, and X-ray photoelectron spectroscopy (XPS). The electrocatalytic activity of Ag catalysts for O 2 reduction reaction (ORR) in 1 M KOH is evaluated using the rotating (ring)-disc electrode method. SEM and HAADF-STEM results show that the unsupported pure-Ag and Ag-CA catalysts consist mainly of big agglomerates, and Ag/C has the smallest agglomerates and some sub-3 nm Ag nanoparticles. The XPS results reveal that Ag in all the catalysts is in the metallic form (Ag 0 ). Despite consisting of big agglomerates, the Ag-CA catalyst exhibits similar ORR electrocatalytic activity to that of Ag/C. Ag-CA (unsupported) shows the lowest hydrogen peroxide yield. These results are of great importance for the development of Ag-based catalysts that can be prepared in a fast, simple and easily up scalable fashion, for anion exchange membrane fuel cells.
Superior photodynamic effect of single-walled carbon nanotubes in aprotic media: a kinetic study
It has been confirmed that single-walled carbon nanotubes (SWCNTs) could generate reactive oxygen species in aprotic media by utilizing photon energy. However, the impact of photon irradiation on SWCNTs and the kinetics of the generation process in aprotic media are still unclear, which significantly limits the yield performance. In this work, the kinetics for photodynamic effects has been investigated by performing characterizations on ultraviolet-treated SWCNTs using Raman spectroscopy, conductive atomic force microscope (in-situ), kelvin probe force microscope, and X-ray photoelectron spectroscopy. It is found that ultraviolet-treated SWCNTs are observed to have more defects, lower conductivity, and less surface charge after energy conversion. Starting from the fundamental intrinsic properties of SWCNTs, the kinetics and formation of these changes are thoroughly discussed. It turns out that the dispersion, chirality, and structural integrity of SWCNTs are important for achieving high-performance photodynamic effects, which are validated using several different SWCNTs as well as other carbon nanomaterials. A type of (6,5) s-SWCNTs exhibited the highest energy efficiency among a variety of other carbon nanomaterials. The yield rate is 2.15 mM/h, and the energy consumption is determined to be 2.79 W∙h/mM. This work is expected to help dramatically boost the energy efficiency of the photodynamic effect in aprotic media and pave the way for designing high-performance carbon nanomaterial-based photoinduced devices.
Electrocatalytic Isoxazoline–Nanocarbon Metal Complexes
In this work, we report the synthesis of new carbon-nanomaterial-based metal chelates that enable effective electronic coupling to electrocatalytic transition metals. In particular, multiwalled carbon nanotubes (MWCNTs) and few-layered graphene (FLG) were covalently functionalized by a microwave-assisted cyclo-addition with nitrile oxides to form metal-binding isoxazoline functional groups with high densities. The covalent attachment was evidenced by Raman spectroscopy, and the chemical identity of the surface functional groups was confirmed by X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The functional carbon nanomaterials effectively chelate precious metals Ir(III), Pt(II), and Ru(III), as well as earth-abundant metals such as Ni(II), to afford materials with metal contents as high as 3.0 atom %. The molecularly dispersed nature of the catalysts was confirmed by X-ray absorption spectroscopy (XAS) and energy-dispersive X-ray spectroscopy (STEM-EDS) elemental mapping. The interplay between the chelate structure on the graphene surface and its metal binding ability has also been investigated by a combination of experimental and computational studies. The defined ligands on the graphene surfaces enable the formation of structurally precise heterogeneous molecular catalysts. The direct attachment of the isoxazoline functional group on the graphene surfaces provides strong electronic coupling between the chelated metal species and the conductive carbon nanomaterial support. We demonstrate that the metal-chelated carbon nanomaterials are effective heterogeneous catalysts in the oxygen evolution reaction with low overpotentials and tunable catalytic activity.
Site-Specific Electronic Properties of [Ag[subscript 25](SR)[subscript 18]][superscript ;#8722;] Nan
Explore the source record for details and available documents.
Tracking the phase changes in micelle-based NiGa nanocatalysts for methanol synthesis under activation and working conditions
The hydrogenation of CO 2 into high energy density fuels such as methanol, where the required H 2 is obtained from renewable sources, is of utmost importance for a sustainable society. In recent years, NiGa alloys have attracted attention as promising catalyst material systems for the hydrogenation of CO 2 into methanol at ambient pressures. They thus represent an energy-saving alternative to the Cu-based catalysts employed in today's catalytic industry that require high pressures for the CO 2 hydrogenation. However, the underlying reaction mechanisms for the NiGa system are still under debate. One of the challenges here is to unravel the evolution and coexistence of the different species in the heterogeneous NiGa catalyst system under activation and reaction conditions. To shed light on their evolution under activation in H 2 and their catalytic roles under CO 2 hydrogenation working conditions on well-defined Ni 3 Ga 1 and Ni 5 Ga 3 nanoparticle (NP) catalysts, we employed a multi-probe approach in this study. It included advanced machine learning-based analysis of operando X-ray absorption spectroscopy data combined with operando powder X-ray diffraction and near ambient pressure X-ray photoelectron spectroscopy measurements, as well as reactivity studies using bed-packed mass flow reactors. In addition, we employed atomic force microscopy and scanning transmission electron microscopy for structural characterization. Under H 2 activation at 1 bar total pressure, we concluded the formation of metallic Ni, starting for Ni 3 Ga 1 at 300 °C, and for Ni 5 Ga 3 at 400 °C. At higher temperatures, the formation of NiGa alloys follows. The α'-Ni 3 Ga 1 alloy phase is predominantly formed for the Ni 3 Ga 1 NPs, while the coexistence of α'-Ni 3 Ga 1 , δ-Ni 5 Ga 3 and Ga 2 O 3 phases is observed for the Ni 5 Ga 3 NPs after the H 2 activation. The formation of the Ga 2 O 3 phase also results in the presence of excess metallic Ni. Under CO 2 hydrogenation reaction conditions, Ga partially oxidizes again to form a Ga 2 O 3 -rich particle shell for both NP compositions, yet, to a larger extent for the Ni 3 Ga 1 NPs, which, in turn, feature a higher amount of excess Ni. We reveal that metallic Ni is responsible for the high selectivity of the Ni 3 Ga 1 NPs towards the production of methane in our catalytic tests. In contrast, the Ni 5 Ga 3 NPs display a strong selectivity toward methanol production (>92%), more than one order of magnitude higher than that for the Ni 3 Ga 1 NPs, which we ascribe to the presence of the δ-Ni 5 Ga 3 phase.
Evaluating Non-Fluoropolymer-Based Co-Extruded Backsheets Using Combined-Accelerated Stress Testing and Materials Forensics
Co-extruded, non-fluoropolymer backsheet films for photovoltaic (PV) modules have gained popularity in recent years based on their cost competitiveness. However, their viability has been thrown into question as a result of widespread, early-life field-failures of some materials, particularly the polyamide (PA)-based “AAA” backsheet product. Failure to detect weaknesses in those earlier products could be due, in part, to insufficient quality testing practices. New testing protocols have recently been developed to better evaluate such materials. Here we show the testing results for a non-fluoropolymer, co-extruded PA-based backsheet film, which demonstrates greater durability than AAA and some commercial fluoropolymers. Using material characterization techniques including Fourier-transform infrared spectroscopy (FTIR), wide-angle x-ray scattering (WAXS), differential scanning calorimetry (DSC), X-ray photoelectron spectroscopy (XPS), elongation-to-break (ETB), and optical microscopy we perform a comprehensive failure analysis to better understand the materials weaknesses. This analysis can ultimately inform how best to improve the material and extend its lifetime. This work serves as a demonstration that some materials should not be discounted due to a single poorly designed product and that more appropriate qualification testing with subsequent materials analysis can be used to develop better materials.