Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PARTITION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Application of strainrange partitioning to the prediction of creep-fatigue lives of AISI types 304 and 316 stainless steel

As a demonstration of the predictive capabilities of the method of Strainrange Partitioning, published high-temperature, low cycle, creep-fatigue test results on AISI Types 304 and 316 stainless steel were analyzed and calculated, cyclic lives compared with observed lives. Predicted lives agreed with observed lives within factors of two for 76 percent, factors of three for 93 percent, and factors of four for 98 percent of the laboratory tests analyzed. Agreement between observed and predicted lives is judged satisfactory considering that the data are associated with a number of variables (two alloys, several heats and heat treatments, a range of temperatures, different testing techniques, etc.) that are not directly accounted for in the calculations.

Saltsman, J. F.↗
NASA NTRS1976

High temperature, low-cycle fatigue of copper-base alloys for rocket nozzles. Part 2: Strainrange partitioning and low-cycle fatigue results at 538 deg C

Low-cycle fatigue tests of 1/2 Hard AMZIRC Copper and NARloy Z were performed in argon at 538 C to determine partitioned strain range versus life relationships. Strain-controlled low-cycle fatigue tests of a Zr-Cr-Mg copper-base alloy were also performed. Strain ranges, lower than those employed in previous tests, were imposed in order to extend the fatigue life curve out to approximately 400,000 cycles. An experimental copper alloy and an experimental silver alloy were also studied. Tensile tests were performed in air at room temperature and in argon at 538 C. Strain-controlled low-cycle fatigue tests were performed at 538 C in argon to define the fatigue life over the regime from 300 to 3,000 cycles. For the silver alloy, three additional heat treatments were introduced, and a limited evaluation of the short-term tensile and low-cycle fatigue behavior at 538 C was performed.

Conway, J. B.↗
NASA NTRS1976

Treatment of multiaxial creep-fatigue by strainrange partitioning

Strainrange partitioning is a recently developed method for treating creep-fatigue interaction at elevated temperature. Most of the work to date has been on uniaxially loaded specimens, where as practical applications often involve load multiaxiality. It is shown how the method can be extended to treat multiaxiality through a set of rules for combining the strain components in the three principal directions. Closed hysteresis loops, as well as plastic and creep strain ratcheting are included. An application to hold-time tests in torsion will be used to illustrate the approach.

S S Manson↗
NASA NTRS1977

Ductility normalized-strainrange partitioning life relations for creep-fatigue life predictions

Procedures based on Strainrange Partitioning (SRP) are presented for estimating the effects of environment and other influences on the high temperature, low cycle, creep fatigue resistance of alloys. It is proposed that the plastic and creep, ductilities determined from conventional tensile and creep rupture tests conducted in the environment of interest be used in a set of ductility normalized equations for making a first order approximation of the four SRP inelastic strainrange life relations. Different levels of sophistication in the application of the procedures are presented by means of illustrative examples with several high temperature alloys. Predictions of cyclic lives generally agree with observed lives within factors of three.

Halford, G. R.↗
NASA NTRS1977

Application of Strainrange Partitioning to the prediction of creep-fatigue lives of AISI Types 304 and 316 stainless steel

As a demonstration of the predictive capabilities of the method of Strainrange Partitioning, published high-temperature, low cycle, creep-fatigue test results on AISI Types 304 and 316 stainless steel were analyzed and calculated cyclic lives compared with observed lives. Predicted lives agreed with observed lives within factors of two for 76 percent, factors of three for 93 percent, and factors of four for 98 percent of the laboratory tests analyzed. Agreement between observed and predicted lives is judged satisfactory considering that the data are associated with a number of variables (two alloys, several heats and heat treatments, a range of temperatures, different testing techniques, etc.) that are not directly accounted for in the calculations.

Saltsman, J. F.↗
NASA NTRS1976

Application of strainrange partitioning to the prediction of MPC creep-fatigue data for 2 1/4 Cr-1 Mo steel

Creep-fatigue tests were conducted on annealed 2.25Cr-1Mo steel in air at 538 C involving interspersion of rapid strain cycles (0 to 22 cycles) between constant tensile stress-hold periods (23 or 47 hours). Life predictions were made on the basis of the strain range-life relations obtained from short-time material characterization tests on tubular specimens taken from the same heat as the specimens for the creep-fatigue tests. The creep-fatigue tests lasted from about 500 to 5000 hours, while the short-time tests used as the prediction basis lasted from 0.1 to 100 hours. By partitioning the creep and plastic strains within every cycle and summing the damage on a cycle-by-cycle basis, the predicted lives agreed with the observed ones within factors of two.

Saltsman, J. F.↗
NASA NTRS1977

Treatment of low strains and long hold times in high temperature metal fatigue by strainrange partitioning

A procedure for treating creep-fatigue for low strainranges and long hold times is outlined. A semi-experimental approach, wherein several cycles of the imposed loading is actually applied to a specimen in order to determine the stable hysteresis loop, can be very useful in the analysis. Because such tests require only a small fraction of the total failure time, they are not inherently prohibitive if experimental equipment is available. The need for accurate constitutive equations is bypassed because the material itself acts to translate the imposed loading into the responsive hysteresis loops. When strainrange partitioning has been applied in such cases very good results have been obtained.

Manson, S. S.↗
NASA NTRS1978

Crossed grid anode and its image partitioning

Measurements on an imaging crossed grid anode following a pair of microchannel plates indicate fast charge propagation via wire-to-wire capacitances, suggesting a temporal resolution of 100 ns. A figure of merit for partitioned systems has been suggested that provides an estimate of the position uncertainty of photoelectrons in the image plane of an anode. Solutions for two-, three-, and four-amplifier position algorithms are given, and basic system requirements are discussed.

Knapp, G.↗
NASA NTRS1977

Impact-induced energy partitioning, melting, and vaporization on terrestrial planets

The reported investigation was conducted in connection with the desirability to obtain information regarding the response of a solidified planetary surface to the primary impact of a meteoroid whose dimensions are small compared to that of the planet. The investigation is an extension of studies conducted by Ahrens and O'Keefe (1977) concerned with a calculation via finite-difference techniques of the entire flow field, the energy partitioning, and the quantity of melt and vapor produced upon impact of an iron object on a gabbroic anorthosite half-space at 15 km/sec. The assumptions used in these calculations are summarized. Calculations based on an equation of state for the low- and high-pressure mineral assemblage of gabbroic anorthosite, initial density 2.94 g/cu cm are considered. An algorithm is formulated for the description of the phase transformation upon shock loading. It is shown that the relative volume of melt and the equivalent volume of shock-induced vapor is proportional to the meteoroid kinetic energy (at high speeds) using the similarity scaling of projectile and target properties as suggested by Dienes and Walsh (1970).

Okeefe, J. D.↗
NASA NTRS1978

Partitioning of transition metals between diopside and coexisting silicate liquids. I - Nickel, cobalt, and manganese

Distribution coefficients have been found for the partitioning of Ni, Co, and Mn between calcium-rich clinopyroxenes and coexisting silicate liquids. Values are found for the 1110-1360 C temperature range. The breakdown of Henry's Law was not observed. The measured clinopyroxene/liquid distribution coefficients ranged from 1.5-14.0 for Ni, 0.5-2.0 for Co, and 0.3-1.2 for Mn. Analyses of pyroxenes grown from charges differing in the amounts of transition metals indicate that Ni and Co occupy the M1 site of diopside and that Mn occupies the M1 and M2 sites. Equilibrium constants were found in terms of the activities of the components in the liquid and solid phases. These activities are based on the mole fractions. An activity/concentration model was used for the liquid phase in order to explain the variations in the clinopyroxene/liquid coefficients due to bulk composition.

Lindstrom, D. J.↗
NASA NTRS1979

The strainrange partitioning behavior of an advanced gas turbine disk alloy, AF2-1DA

The low-cycle, creep-fatigue characteristics of the advanced gas turbine disk alloy, AF2-1DA have been determined at 1400 F and are presented in terms of the method of strainrange partitioning (SRP). The mean stresses which develop in the PC and CP type SRP cycles at the lowest inelastic strainrange were observed to influence the cyclic lives to a greater extent than the creep effects and hence interfered with a conventional interpretation of the results by SRP. A procedure is proposed for dealing with the mean stress effects on life which is compatible with SRP.

Halford, G. R.↗
NASA NTRS1979

Technical evaluation report of the Specialists Meeting on Characterization of Low Cycle High Temperature Fatigue by the Strainrange Partitioning Method

The ability of the Strainrange Partitioning Method SRP was evaluated to correlate the creep-fatigue behavior of gas turbine materials and to predict the creep fatigue life of laboratory specimens subjected to complex cycling conditions. A reference body of high temperature creep fatigue data which can be used in the evaluation of other SRP and low cycle high temperature fatigue predictive techniques was provided.

Drapier, J. M.↗
NASA NTRS1979

The strainrange partitioning behavior of an advanced gas turbine disk alloy, AF2-1DA

The low-cycle, creep-fatigue characteristics of the advanced gas turbine disk alloy, AF2-1DA have been determined at 1400 F and are presented in terms of the method of strainrange partitioning (SRP). The mean stresses which develop in the PC (tensile Plasticity reversed by compressive Creep) and CP (tensile Creep reversed by compressive Plasticity) type SRP cycles at the lowest inelastic strainrange were observed to influence the cyclic lives to a greater extent than the creep effects and hence interfered with a conventional interpretation of the results by SRP. A procedure is proposed for dealing with the mean stress effects on life which is compatible with SRP.

Halford, G. R.↗
NASA NTRS1978

The Apollo 16 drive tube 60009/60010. II - Petrology and major element partitioning among the regolith components

The paper summarizes petrographic and electron microprobe data from 22 polished thin sections that represent the total length of double drive tube 60009/60010 and discusses a new application of the method of modal recombination to estimate bulk chemistry. The modal recombination approach can be used to reliably calculate the chemistry of the greater than 0.02-mm size fraction and, more significantly, to derive the total major element partitioning among the regolith components.

Vaniman, D. T.↗
NASA NTRS1981

Ni partitioning between diopside and silicate melt - A redetermination by ion microprobe and recognition of an experimental complication

The capabilities of and potential problems with ion microprobe analysis are illustrated in the determination of Ni distribution between silicate melt and diopside as a function of concentration. Samples of diopside and a melt in the albite-anorthite-diopside system were doped with Ni to levels of 5.22 and 1.08 wt % and 1060, 138, 42 and 30 ppm, and with 3 ppm of Ni-63, and characterized by both electron and ion microprobe techniques. Measurements of Ni-62 distribution by the ion probe method give a ratio of 1.87 for the ratio of count rates in the diopsides with the glass, which is slightly lower than the value of 2.05 obtained from beta-track mapping. The measurements required the secondary ion signal to be linear with concentration in the range measured, and a calibration to correct for differential secondary ion yields from different phases. It is found, however, that partition coefficients measured for Ni-58 and Ni-60 are not constant with Ni concentration, probably due to Ni migration during crystallization. The results thus show ion microprobe analyses to be feasible for simultaneous measurements of distributions of more than one element, and of elements inappropriate for beta-track mapping or electron probe analysis.

Steele, I. M.↗
NASA NTRS1981

Hydrogen partitioning in pure cast aluminum as determined by dynamic evolution rate measurements

Hydrogen in pure aluminum can be found in two different states. One is related to a presence in gas-filled pores, while the other state involves the formation of a solid solution between hydrogen and aluminum. The considered investigation is concerned with the distribution of the hydrogen between various states. A dynamic technique is employed to measure the evolution of hydrogen from commercially available samples of polycrystalline pure aluminum under ultrahigh vacuum conditions. The obtained data are compared with the results of a statistical analysis concerning the porosity in the cast aluminum. It was found that more than 99 pct of the hydrogen in the aluminum is located in large pores. Less than 1 pct of the hydrogen is partitioned between the solid solution and the small pores.

Outlaw, R. A.↗
NASA NTRS1982

Initial energy partitioning and some excavation stage phenomenology in laboratory-scale cratering calculations in clay

One impact and two explosive cratering calculations have been analyzed with emphasis on the early excavation stage. The early excavation stage is here defined as that part of the excavation stage that occurs after energy partitioning is 90% complete, but before the cratering flow field can be well described by Z-type flow fields with values of Z uniformly greater than two. Impact generated flow fields seem to have a much longer early excavation stage than explosion generated flow fields, due possibly to the slower momentum transfer versus energy transfer rate between projectile and target. During this time when the projectile retains a significant portion of its original momentum, Z values less than two are observed in the impact generated flow field. Z values less than two are not observed at any time in the explosion generated flow fields.

Austin, M. G.↗