The Restructuring-Induced CoO x Catalyst for Electrochemical Water Splitting
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
SEARCH · Engineering Papers
Results for “Oxygen evolution reaction”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Dynamic Surface Reconstruction Unifies the Electrocatalytic Oxygen Evolution Performance of Nonstoichiometric Mixed Metal Oxides
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
LTE-P-14 Non PGM Conductivity measurement
A procedure for measuring the electrical conductivity of PGM-free OER catalyst powders to allow comparison of one material to another. This standard two-point conductivity protocol is applicable to transition metal oxides, mixed oxides, perovskites, spinels, etc.
08 HYDROGEN↗
LTE-P-13 3-Electrode Cell for Screening OER/HER Electrocatalyst Activity
Procedure for screening HER/OER electrocatalysts using fully immersed electrodes covered with electrocatalyst. Optimized for usage in alkaline solutions with high loading of electrocatalysts up to 4 mg/cm2. Can be used for both PGM and PGM-free catalysts.
08 HYDROGEN↗
Revealing the coupled oxygen and hypochlorite chemistry in saltwater batteries through operando pH and oxygen monitoring
Saltwater batteries (SWBs) that utilize Na⁺ ions from seawater have emerged as promising candidates for low-cost and sustainable grid-scale energy storage. To date, the cathode reaction mechanism of SWBs has been predominantly described by oxygen evolution and reduction reactions (OER/ORR). However, this assumption is valid only under idealized ocean-like conditions with constant pH and continuous oxygen replenishment. In practical systems, SWBs operate in finite volumes of saltwater, where saltwater composition dynamically evolves during cycling. Here, in this work, we systematically investigate the cathode reaction mechanisms of SWBs under finite saltwater conditions using galvanostatic cycling combined with electrochemical diagnostics and operando monitoring of dissolved oxygen and pH. Our results reveal that the cathode chemistry during SWB operation is considerably more complex than previously assumed. In addition to OER and ORR, hypochlorite formation and consumption reactions, along with pH-dependent switching of dominant reaction pathways, play critical roles. We further identify the sequence and relative contributions of these reactions throughout charge–discharge cycling. These findings provide a comprehensive and mechanistically grounded understanding of SWB cathode processes under relatively realistic cell design and operation condition. The insights presented here establish a new framework for interpreting SWB electrochemistry and offer directions for future strategies aimed at improving performance, stability, and practical viability.
Hypochlorite redox reaction↗
Kinetically Stable Oxide Overlayers on Mo 3 P Nanoparticles Enabling Lithium–Air Batteries with Low Overpotentials and Long Cycle Life
The main drawbacks of today's state-of-the-art lithium–air (Li–air) batteries are their low energy efficiency and limited cycle life due to the lack of earth-abundant cathode catalysts that can drive both oxygen reduction and evolution reactions (ORR and OER) at high rates at thermodynamic potentials. Here, inexpensive trimolybdenum phosphide (Mo 3 P) nanoparticles with an exceptional activity—ORR and OER current densities of 7.21 and 6.85 mA cm –2 at 2.0 and 4.2 V versus Li/Li + , respectively—in an oxygen-saturated non-aqueous electrolyte are reported. The Tafel plots indicate remarkably low charge transfer resistance—Tafel slopes of 35 and 38 mV dec –1 for ORR and OER, respectively—resulting in the lowest ORR overpotential of 4.0 mV and OER overpotential of 5.1 mV reported to date. Using this catalyst, a Li–air battery cell with low discharge and charge overpotentials of 80 and 270 mV, respectively, and high energy efficiency of 90.2% in the first cycle is demonstrated. Furthermore, a long cycle life of 1200 is also achieved for this cell. Density functional theory calculations of ORR and OER on Mo 3 P (110) reveal that an oxide overlayer formed on the surface gives rise to the observed high ORR and OER electrocatalytic activity and small discharge/charge overpotentials.
25 ENERGY STORAGE↗
In Situ EXAFS Study of Mo–P Bond Dynamics in Molybdenum Phosphide during CO 2 Reduction and Hydrogen Evolution
Transition Metal Phosphides (TMPs) are widely studied as catalysts in reactions like hydrogen evolution, oxygen reduction, and hydrodesulfurization. TMPs have demonstrated remarkable efficiency in accelerating reactions by providing active sites for adsorption and facilitating the transformation of reaction intermediates, a feature that has increased the interest of TMPs in the electrochemical carbon dioxide reduction reaction (eCO 2 RR). Despite their growing use, the potential-dependent structural behavior of TMPs under operating electrochemical conditions remains insufficiently understood. This work investigates the dynamics of the Mo−P bond during eCO 2 RR and hydrogen evolution reaction (HER) using in situ extended X-ray absorption spectroscopy (EXAFS) studies at the Mo−K edge. Structural characterization of the synthesized MoP nanoparticles was performed by powder X-ray diffraction (XRD) and transmission electron microscopy (TEM). Results of the overall electrochemical activity of MoP are presented through linear sweep voltammetry (LSV) experiments in the potential range of 0 to −1.5 V versus Ag/AgCl and chronoamperometry (CA). Liquid products were analyzed by 1 H NMR spectroscopy. The synthesized catalyst showed increasing activity with the highest Faradaic efficiency of 11.75% for C 2+ products at −1.3 V vs Ag/AgCl. In situ EXAFS revealed a change in the average Mo−P bond distance during eCO 2 RR, whereas no such change was observed during the hydrogen evolution reaction (HER). This finding suggests that phosphorus, particularly through modulation of the Mo−P bond length, plays an important role in the eCO 2 RR and demonstrates how in situ EXAFS can track local structural perturbations in MoP catalysts during electrochemical operation, providing complementary structural insight that correlates with electrochemical behavior.
Catalysts↗
Laser-Irradiated Holey Graphene-Supported Single-Atom Catalyst towards Hydrogen Evolution and Oxygen Reduction
Single-atom catalysts (SAC) can boost the intrinsic catalytic activity of hydrogen evolution reaction (HER) and oxygen reduction reaction (ORR). However, the challenge remains due to the complex synthesis process and insufficient stability. A sustainable approach is applied to synthesizing SACs through laser irradiation and gaining mesoporous graphene oxide (MGO). The surface dangling bonds of nitrogen-doped MGO (NMGO) extract metal atoms species from Co or Fe metal foams and convert them to SAC via an appropriate synthesis approach. Notably, the Co-NMGO electrocatalyst requires low potentials of 146 mV to convey a current density of 10 mA cm -2 towards HER. Similarly, the Fe-NMGO electrocatalyst offers an onset of 0.79 V towards ORR in acidic solution. The individual metal atoms are confirmed via aberration-corrected scanning transmission electron microscopy, and X-ray absorption near-edge structure and extended X-ray absorption fine structure. Density functional theory calculations by applying the grand canonical potential kinetics model revealed that Co-NMGO shows the optimum free reaction energy of -0.17 eV at -0.1 V for HER, and Fe-NMGO has less limiting potential than that of Co-NMGO for ORR case. Furthermore, this work opens a new approach towards the synthesis of SAC and its mechanistic understandings.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Probing the active sites of oxide encapsulated electrocatalysts with controllable oxygen evolution selectivity
Electrocatalysts encapsulated by nanoscopic overlayers can control the rate of redox reactions at the outer surface of the overlayer or at the buried interface between the overlayer and the active catalyst, leading to complex behavior in the presence of two competing electrochemical reactions. This study investigated oxide encapsulated electrocatalysts (OECs) comprised of iridium (Ir) thin films coated with an ultrathin (2–10 nm thick) silicon oxide (SiO x ) or titanium oxide (TiO x ) overlayer. The performance of SiO x |Ir and TiO x |Ir thin film electrodes towards the oxygen evolution reaction (OER) and Fe(II)/Fe(III) redox reactions were evaluated. An improvement in selectivity towards the OER was observed for all OECs. Overlayer properties, namely ionic and electronic conductivity, were assessed using a combination of electroanalytical methods and molecular dynamics simulations. SiO x and TiO x overlayers were found to be permeable to H 2 O and O 2 such that the OER can occur at the MO x |Ir (M = Ti, Si) buried interface, which was further supported with molecular dynamics simulations of model SiO 2 coatings. In contrast, Fe(II)/Fe(III) redox reactions occur to the same degree with TiO x overlayers having thicknesses less than 4 nm as bare electrocatalyst, while SiO x overlayers inhibit redox reactions at all thicknesses. This observation is attributed to differences in electronic transport between the buried interface and outer overlayer surface, as measured with through-plane conductivity measurements of wetted overlayer materials. These findings reveal the influence of oxide overlayer properties on the activity and selectivity of OECs and suggest opportunities to tune these properties for a wide range of electrochemical reactions.
08 HYDROGEN↗
Novel Co‐Catalytic Activities of Solid and Liquid Phase Catalysts in High‐Rate Li‐Air Batteries
Abstract Li‐air batteries are considered strong candidates for the next‐generation energy storage systems designed for electrical transportation. However, low cyclability and current rates are two major drawbacks that hinder them from further realization. These issues necessitate the discovery of novel materials to significantly enhance the redox process of discharge products. In this study, a novel catalytic system comprised of tin sulfide (SnS) nanoflakes as a solid catalyst and tin iodide (SnI 2 ) as a dual‐functional electrolyte additive is discovered. This system enables operating the battery at high current rates up to 10 000 mA g −1 (corresponding to 1 mA cm −2 ). The SnS catalyst shows outstanding catalytic activity for both oxygen reduction and evolution reactions compared to carbon, noble metals, and other transition metal dichalcogenides. It also exhibits good structural integrity at high rates. The computations indicate numerous possible oxygen reduction sites without oxygen dissociations on the SnS surface through solution mechanism that is likely responsible for the formation of Li 2 O 2 . The calculations also indicate that the role of the SnI 2 is not only reacting with the lithium anode to provide protection but reducing the charge potential by promoting catalytic decomposition of the Li 2 O 2 . This work provides new novel additives for designing high‐rate Li‐air batteries.
25 ENERGY STORAGE↗
Critical Assessment of Electronic Structure Descriptors for Predicting Perovskite Catalytic Properties
The discovery and design of materials which can efficiently catalyze the oxygen reduction and evolution reactions at reduced temperatures is important for facilitating the widespread adoption of fuel cell and electrolyzer technologies. Numerous studies have produced correlations between catalytic properties, such as oxygen surface exchange or electrode area specific resistance (ASR), and properties of the catalyst material. However, correlations have historically been limited in scope (e.g., using only a few materials or at a single temperature) and it has been difficult to provide detailed assessments of their robustness. Here, in this study, we assess the ability of the O p-band center electronic structure descriptor, obtained from density functional theory (DFT) calculations, to correlate with oxygen surface exchange rates, diffusivities, and area specific resistances for a large database of perovskite oxide catalytic properties. By data mining the literature, we obtain 747 catalytic property value data points spanning 299 unique perovskite compositions from 313 studies. We assess linear correlations of each property with the O p-band center and find generally modest correlations that are qualitatively useful (prediction mean absolute errors of about 0.5 log units are typical), where the correlations are improved at higher temperatures (e.g., 800 °C vs. 500 °C) and significantly improve when considering fits to the subset of materials which have multiple independent measurements. These findings suggest that the spread of property data is significantly influenced by experimental uncertainty, and subsequent measurements of additional materials will likely improve the O p-band center correlations.
30 DIRECT ENERGY CONVERSION↗
Janus Nanocages of Platinum-Group Metals and Their Use as Effective Dual-Electrocatalysts
Janus nanocages with distinctive platinum-group metals on the outer and inner surfaces can naturally catalyze at least two different reactions. In this work, we report a general method based on successive deposition and then selective etching for the facile synthesis of such nanocages. Herein, we have fabricated 11 different types of Janus nanocages characterized by a uniform size and well-defined {100} facets, together with porous, ultrathin, asymmetric walls up to 1.6 nm thick. When tested as dual-electrocatalysts toward oxygen reduction and evolution reactions, the Janus nanocages based on Pt and Ir exhibited superior activities depending on the thickness and relative position of the metal layer. Density functional theory studies suggest that the alloy composition and surface structure of the nanocages both play important roles in enhancing the electrocatalytic activities by modulating the stability of key reaction intermediates.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Machine Learning Design of Perovskite Catalytic Properties
Abstract Discovering new materials that efficiently catalyze the oxygen reduction and evolution reactions is critical for facilitating the widespread adoption of solid oxide fuel cell and electrolyzer (SOFC/SOEC) technologies. Here, machine learning (ML) models are developed to predict perovskite catalytic properties critical for SOFC/SOEC applications, including oxygen surface exchange, oxygen diffusivity, and area specific resistance (ASR). The models are based on trivial‐to‐calculate elemental features and are more accurate and dramatically faster than the best models based on ab initio‐derived features, potentially eliminating the need for ab initio calculations in descriptor‐based screening. The model of ASR enables temperature‐dependent predictions, has well calibrated uncertainty estimates and online accessibility. Use of temporal cross‐validation reveals the model to be effective at discovering new promising materials prior to their initial discovery, demonstrating the model can make meaningful predictions. Using the SHapley Additive ExPlanations (SHAP) approach, detailed discussion of different approaches of model featurization is provided for ML property prediction. Finally, the model is used to screen more than 19 million perovskites to develop a list of promising cheap, earth‐abundant, stable, and high performing materials, and find some top materials contain mixtures of less‐explored elements (e.g., K, Bi, Y, Ni, Cu) worth exploring in more detail.
25 ENERGY STORAGE↗
Intermediate Temperature Solid Oxide Cell with a Barrier Layer Free Oxygen Electrode and Phase Inversion Derived Hydrogen Electrode
High-temperature solid oxide cells (SOCs) have fundamental advantages in efficiency and product rate over their low-temperature counterparts. However, the commercial development of SOCs is hindered by cost and reliability. To solve the issues, lowering the operating temperature of SOCs is deemed the best solution. Here we report on our effort toward intermediate temperature (IT) SOCs by developing a barrier layer free high-performance oxygen electrode and open structured hydrogen electrode. The results show that the new oxygen electrode provides reasonably good oxygen electrocatalytic activity at IT range for oxygen reduction and evolution reactions and the open structured hydrogen electrode provides low gas diffusion path for H 2 /H 2 O. However, at high electrolysis current density such as 1 A cm −2 and 650 °C, the present oxygen electrode delaminates after 200 h. The phase-inversion derived open structured hydrogen electrode helps gas diffusion but, in the meantime, reduces reactive sites. A proper balance of porosity and number of reactive sites is still needed for future hydrogen electrode development.
25 ENERGY STORAGE↗
Hypochlorite Redox Chemistry Enables High-Voltage and High-Power Saltwater Batteries
Saltwater batteries (SWBs) are promising alternatives to lithium-ion batteries for large-scale stationary energy storage. However, the performance of conventional oxygen redox-based saltwater battery systems is often constrained by sluggish oxygen evolution and reduction reactions (OER/ORR) at the cathode, leading to low voltage efficiency and limited power density. Here, OER and ORR are replaced by hypochlorite-based redox reactions through the introduction of sodium hypochlorite into saltwater. Operando pH and dissolved oxygen measurements confirm that OER and ORR are minimized and that hypochlorite redox reactions dominate the cathode behavior. Owing to the higher operating potential and faster reaction kinetics, the hypochlorite-redox-based SWBs delivers a higher discharge voltage of 3.3 V and reduced charge-discharge voltage polarization to 0.66 V. Further improvement is achieved by adjusting the saltwater pH to near-neutral conditions, increasing the discharge voltage to 3.5 V and more than doubling the peak power. The hypochlorite redox environment also exhibits chemical stability with key cell components, including the solid electrolyte and cathode current collectors. Operation of series-connected cells and cells employing hard carbon anodes demonstrates scalability and compatibility with alternative anode materials. These results provide a strong foundation for next-generation SWBs targeting large-scale stationary energy storage applications.
Go, Wooseok [ORNL]↗
(La 0.8 Sr 0.2 ) 0.98 MnO 3-δ -Zr 0.92 Y 0.16 O 2-δ :PrOx for oxygen electrode supported solid oxide cells
(La 0.8 Sr 0.2 ) 0.98 MnO 3-δ (LSM)- Zr 0.92 Y 0.16 O 2-δ (YSZ) has been widely studied as the cathode for solid oxide fuel cells (SOFCs), but its low activity has been a cell performance limiting factor. Herein, LSM-YSZ:PrO x composite is developed as an active electrocatalyst for both oxygen reduction and evolution reactions. A single step PrO x infiltration into LSM-YSZ lowers the polarization resistance (Rp) 10–20 times depending on the test temperature. Distribution of relaxation times (DRT) calculation reveals that adding PrO x affects surface exchange between adsorbed/desorbed oxygen and lattice oxygen, and oxygen dissociative adsorption/desorption. A symmetrical cell with a thin YSZ electrolyte sandwiched between thick LSM-YSZ:PrO x electrode-supports is developed and its oxygen generation performance and stability are evaluated under various current densities and temperatures. Finally, reversible solid oxide cell (ReSOC) performance is also reported for LSM-YSZ:PrO x supported cells with the oxide fuel electrode Sr 0.95 (Ti 0.3 Fe 0.63 Ni 0.07 )O 3-δ (STFN).
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Comparative Study on the Photoelectrochemical Hydrogen Production from the Layout Optimization in a Unit Cell
Solar-driven water splitting is achieved by connecting photovoltaics with electrolysis. Recently, integrated approaches of the two configurations for photoelectrochemical reactions have shown great potential in a combined unit, but strategies to address further material and cell development face significant scientific challenges. Here, in this work, we present an experimental demonstration of photoelectrochemical (PEC) unit-cells with efficient separate dual compartments for oxygen evolution and hydrogen evolution reactions. The design and fabrication of cell architectures with various degrees of integration are investigated efficient and sustainable PEC processes. The effect of the nanostructured silicon (Si) photoelectrodes, including the adoption of layer architectures, surface protection layer deposition, and membrane electrode assembly is further studied to optimize the design parameters of the PEC unit-cells. This developed PEC cell with the Si photocathode achieved a photocurrent density of -4.8 mA cm –2 at -2.0 V cell and -2.87 mA cm –2 at -1.6 V cell . It clearly provides a critical milestone for unbiased solar water splitting. Practical solar to hydrogen (STH) can be directly estimated in investigating PEC performance in this unit-cell as assembled with a solar cell. It is a significantly meaningful step forward in practical solar fuel production.
08 HYDROGEN↗