Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nano structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Failure analysis and design principles of silicon-based lithium-ion batteries using micron-sized porous silicon/carbon composite

Significant progresses have been made to overcome the fundamental challenges in silicon (Si)-based lithium-ion batteries (LIBs). However, much less work have been reported on the design and failure analysis these batteries for practical applications. In this work, we analyzed various cell design parameters affecting the performance of pouch cells using micron-sized porous Si with nano-pore structure and coated by pitch-carbon (p-Si/C). The correlation among particle level, electrode level, and cell level properties, especially the effect of electrode density on the volumetric capacity density of Si anode and full batteries have been systematically investigated. It is found that the corrosion of p-Si/C particle surface is the main failure mechanisms on the eventual capacity loss, while Li plating on anode electrode surface is the main reason for the fast capacity loss in later stage of cycling. The volumetric capacity of Si anode highly depends on both electrode density and the Si content. Moreover, the prelithiation of Si anodes is found to increase energy density while decreasing cycle life of Si-based full cells. Finally, the pathways and strategies for adoption of micron-sized p-Si/C anodes in LIBs have been proposed for their practical applications.

25 ENERGY STORAGE↗

Physical/chemical properties of tin oxide thin film transistors prepared using plasma-enhanced atomic layer deposition

Thin film transistors (TFTs) with tin oxide films as the channel layer were fabricated by means of plasma enhanced atomic layer deposition (PE-ALD). The as-deposited tin oxide films show n-type conductivity and a nano-crystalline structure of SnO{sub 2}. Notwithstanding the relatively low deposition temperatures of 70, 100, and 130 °C, the bottom gate tin oxide TFTs show an on/off drain current ratio of 10{sup 6} while the device mobility values were increased from 2.31 cm{sup 2}/V s to 6.24 cm{sup 2}/V s upon increasing the deposition temperature of the tin oxide films.

36 MATERIALS SCIENCE↗

Synthesis of novel 3D SnO flower-like hierarchical architectures self-assembled by nano-leaves and its photocatalysis

Highlights: • Novel 3D SnO flowers self-assembled by 2D nano-leaves were synthesized by hydrothermal method. • The SnO nano-leaf is of single crystalline nature. • The band gap of 2.59 eV of as-prepared products was obtained. • The as-synthesized material will be a promising photocatalytic material. - Abstract: In this report, the novel 3D SnO flower-like hierarchical architectures self-assembled by 2D SnO nano-leaves are successfully synthesized via template-free hydrothermal approach under facile conditions. The high-resolution transmission electron microscopy results demonstrate that the 2D nano-leaves structure is of single crystalline nature. The band gap 2.59 eV for prepared product is obtained from UV–vis diffuse reflectance spectrum. The photocatalysis of the as prepared SnO for degrading methyl orange (MO) has been studied. A good photocatalytic activity is obtained and the mechanism is discussed in detail. Results indicate that the SnO nanostructures are the potential candidates for photocatalyst applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Investigation of super-capacitive nature of reduced graphene oxide nano mesh grown over 18 k gold foil using wings of Parides iphidamas as biological template

Highlights: • Novel rGO nano mesh (rGONM) like assembly was fabricated using bio-template method. • rGONM pattern exhibit nano-ridges (40 nm) and ribs (25 nm) resembling fishing net. • Super-capacitor performances of rGO and rGONM coated Au substrates were evaluated. • rGO-Au and rGONM-Au revealed specific capacitances of 291 and 418 F/g respectively. - Abstract: This paper deals with the fabrication of novel, reduced graphene oxide nano mesh (rGONM) patterns with longitudinal nano-ridges and transverse nano-ribs using nano tubular structures found on the scales of Parides iphidamas, a butterfly species as biological template. Raman spectra, EDAX and FTIR results confirm the obtained mesh-like morphology that comprises only reduced graphene oxide (rGO). Further, super-capacitor performances of rGO and rGONM-coated gold substrates have been evaluated using cyclic-voltammetry (CV), galvanostatic charge-discharge cycle (GCD) and electrochemical impedance spectroscopic (EIS) analysis. A characteristic rectangular curve obtained from the CV of rGO and rGONM-coated gold electrodes display specific capacitances of 291 F/g and 418 F/g respectively at a scan rate of 5 mV/s. The results obtained from EIS support the superior nature of rGONM-coated electrode against rGO system, suggesting the use of rGONM-Au as a potential candidate for electrochemical super capacitor applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Influence of grain size on α' Cr precipitation in an isothermally aged Fe-21Cr-5Al alloy

Cr-rich α' precipitation during aging typically leads to hardening and accordingly embrittlement of FeCrAl alloys, which needs to be suppressed. The influence of grain size on α' precipitation was studied by aging coarse-grained (CG), ultra-fine grained (UFG), and nanocrystalline (NC) ferritic Kanthal-D [KD; Fe-21Cr-5Al (wt.%) alloy] at 450, 500 and 550 °C for 500 h. After aging at 450 and 500 °C, less hardening was observed in the UFG KD than in CG KD. Atom probe tomography indicated a lower number density and larger sized intragranular α' in the UFG versus the CG alloy. The smaller grain size and higher defect (vacancy and dislocation) density in the UFG KD facilitated diffusion and accordingly enhanced precipitation kinetics, leading to coarsening of precipitates, as well as saturation of precipitation at lower temperatures, as compared to those in CG KD. No hardening occurred in UFG and CG KD after aging at 550 °C, indicating that the miscibility gap is between 500 and 550 °C. NC KD exhibited softening after aging owing to grain growth. α' precipitation occurred in NC KD aged at 450 °C but not at 500 °C, indicating that miscibility gap is between 450 and 500 °C. Thus, the significantly smaller grain size in NC KD decreased the miscibility gap, as compared to that in CG and UFG KD. Finally, this is attributed to the absorption of vacancies by migrating grain boundaries during aging, suppressing α' nucleation and enhancing Cr solubility.

36 MATERIALS SCIENCE↗

Bifacial effects of engineering tumour cell-derived exosomes on human natural killer cells

Extracellular vesicles (EVs) are nano vesicular structures that are secreted by almost all kinds of cells. Exosomes are small EVs derived from endosomes, with a diameter between 30–100 nm. Tumour-derived exosomes carry many molecules and factors from tumour cells. These exosomes are recognized and taken up by immunocytes. However, tumour-derived exosomes can not only suppress immune cell functions but also help tumours escape immune surveillance in the tumour microenvironment. The present work investigated the effect of exosomes derived from genetical modified K562 cells (GMK cells), which express IL-15, IL-18 and 4-1BBL (TNFSF9) on their surface. The results showed that these GME exosomes, carrying IL-15, IL-18 and 4-1BBL proteins similar to their host cells, could activate NK cells, increase the cytotoxicity of NK cells on some tumour cells in a short treatment (4 h) and promote NK cells proliferation. However, with an extended treatment time (48 h), these exosomes could inhibite the cytotoxicity of NK cells by inhibiting activated receptor expression on NK cells. These results indicated the bifacial effects of GMK exosomes on NK cells, which will be helpful to explore the possibility of using transformed exosomes as an anti-tumour immune vaccine or a therapeutic tool in future.

60 APPLIED LIFE SCIENCES↗

X-ray Energy-Dispersive Spectrometry During In Situ Liquid Cell Studies Using an Analytical Electron Microscope

The use of analytical spectroscopies during scanning/transmission electron microscope (S/TEM) investigations of micro- and nano-scale structures has become a routine technique in the arsenal of tools available to today's materials researchers. Essential to implementation and successful application of spectroscopy to characterization is the integration of numerous technologies, which include electron optics, specimen holders, and associated detectors. While this combination has been achieved in many instrument configurations, the integration of X-ray energy-dispersive spectroscopy and in situ liquid environmental cells in the S/TEM has to date been elusive. In this work we present the successful incorporation/modifications to a system that achieves this functionality for analytical electron microscopy.

Zaluzec, Nestor J.↗

Mechanically Robust Bismuth-Embedded Carbon Microspheres for Ultrafast Charging and Ultrastable Sodium-Ion Batteries

Advancements in the development of fast-charging and long-lasting microstructured alloying anodes with high volumetric capacities are essential for enhancing the operational efficiency of sodium-ion batteries (SIBs). These anodes, however, face challenges such as declined cyclability and rate capability, primarily due to mechanical degradation reduced by significant volumetric changes (over 252%) and slow kinetics of sodium-ion storage. Herein, we introduce a novel anode design featuring densely packed bismuth (Bi) embedded within highly conductive carbon microspheres to overcome the aforementioned challenges. Remarkably, the high loading Bi anode within carbon microspheres with a high tap density of 2.59 g cm -3 possesses significant mechanical strength exceeding 590 MPa and limits volume swelling of only 10.9% post-sodiation. This anode demonstrates a high volumetric capacity (908.3 mAh cm -3 ), ultrafast chargeability (200 A g -1 , full charge/discharge in just 5.5 s), and outstanding cyclability over 12,000 cycles and maintains exceptional cycling stability even at -30 °C. The full cell paired with a Na 3 V 2 (PO 4 ) 3 cathode retains over 80% capacity after 600 cycles at 36 C, demonstrating a remarkable rate capability of 126 C (full charge/discharge in 28.6 s). Our comprehensive experimental evaluations and chemo-mechanical simulations shed light on the mechanisms underpinning the anode's superior performance. In conclusion, this development marks a significant advancement in the design of durable and fast-charging anodes for high-performance SIBs.

25 ENERGY STORAGE↗

Solvent-derived defects suppress adsorption in MOF-74

Defects in metal-organic frameworks (MOFs) have great impact on their nano-scale structure and physiochemical properties. However, isolated defects are easily concealed when the frameworks are interrogated by typical characterization methods. In this work, we unveil the presence of solvent-derived formate defects in MOF-74, an important class of MOFs with open metal sites. With multi-dimensional solid-state nuclear magnetic resonance (NMR) investigations, we uncover the ligand substitution role of formate and its chemical origin from decomposed N,N-dimethylformamide (DMF) solvent. The placement and coordination structure of formate defects are determined by 13 C NMR and density functional theory (DFT) calculations. The extra metal-oxygen bonds with formates partially eliminate open metal sites and lead to a quantitative decrease of N 2 and CO 2 adsorption with respect to the defect concentration. In-situ NMR analysis and molecular simulations of CO 2 dynamics elaborate the adsorption mechanisms in defective MOF-74. Our study establishes comprehensive strategies to search, elucidate and manipulate defects in MOFs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

X-ray photoelectron spectroscopy of morpholinium ionic liquids: impact of a long alkyl side substituent on the cation–anion interactions

In this study, X-ray photoelectron spectroscopy is used to analyse nine morpholinium ionic liquids, which are of great interest in green chemistry because of their low toxicity and high recyclability. Here, the effect of the alkyl chain length on the aliphatic C 1s binding energy and the impact of the anion basicity on the cationic N 1s and O 1s binding energies are investigated. It is concluded that by changing the basicity of the anion, there is a more notable change in the electronic environment of the oxygen centre. The impact of a long alkyl side substituent on the cation–anion interactions is also discussed. It is observed that there is an intense charge shielding effect of the alkyl side chain in the cases of octyl and dodecyl substituents, which is reflected in the reduced Br 3d 5/2 binding energy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fabrication of 3-{mu}m diameter pin hole array (PHA) on thick W substrates

Pin-hole arrays are used for a variety of applications including, for example, X-ray imaging of laser-plasmas for fusion relevant studies. More recently, a novel X-ray imaging technique has been proposed (this conference L. A. Gizzi et al.) within the High Power Laser Energy Research Facility (HiPER) to obtain spectrally resolved X-ray imaging using single photon detection. This technique requires a large number of images or, alternatively, large arrays of pin-holes, possibly with very small diameter (<<10 {mu}m). In view of this, a technique was implemented for the fabrication of large arrays of pin-holes in thick metal substrates. Here we report on the optimizations of the laser-matter interaction process to obtain high aspect ratio cylinder-like pin-hole on heavy metal substrate by using a frequency-doubled Ti:Sa femtosecond laser pulses operating at 10 Hz. The influence of an air breakdown and a (ns)prepulse, on the drilled pin-hole, is showed by means of SEM images both for surface effects and internal quality of the channels, with evidence of micro and nano-sized structures. The holes drilled at an intensity just below the laser breakdown threshold for plasma creation in air, have an internal diameter of about 3 {mu}m on a W substrate of 70 {mu}m thickness, a micro-cylinder-like shape and no detectable deviations of the axis from a straight line. Arrays of up to 800 pin-holes were produced with the pin-hole properties being highly stable across the array. The final X-ray transmission is showed by using a mu-focus X-ray source.

36 MATERIALS SCIENCE↗

Nanoporosity induced by ion implantation in deposited amorphous Ge thin films

The formation of a nano-porous structure in amorphous Ge thin film (sputter-deposited on SiO{sub 2}) during ion irradiation at room temperature with 300 keV Ge{sup +} has been observed. The porous film showed a sponge-like structure substantially different from the columnar structure reported for ion implanted bulk Ge. The voids size and structure resulted to be strongly affected by the material preparation, while the volume expansion turned out to be determined only by the nuclear deposition energy. In SiGe alloys, the swelling occurs only if the Ge concentration is above 90%. These findings rely on peculiar characteristics related to the mechanism of voids nucleation and growth, but they are crucial for future applications of active nanostructured layers such as low cost chemical and biochemical sensing devices or electrodes in batteries.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of oriented topological defects on the mechanical properties of carbon nanotube heterojunctions

The mechanical properties of finite-length (5,0)/(8,0) single-walled carbon nanotube (SWCNT) heterojunctions with manipulated topological defects are investigated using molecular dynamics simulation calculations. The results show that the mechanical properties and deformation behavior of SWCNT heterojunctions are mainly affected not only by the diameter of the thinner segment of the SWCNT heterojunction but also by the orientation of the heptagon-heptagon (7-7) pair in the junction region. Moreover, the orientation of the 7-7 pair strongly affects those properties in the compression loading than those in tensile loading. Finally, it is found that the location of buckling deformation in the heterojunctions is dependent on the orientation of the 7-7 pair in the compression.

36 MATERIALS SCIENCE↗

Nano-porosity in GaSb induced by swift heavy ion irradiation

Nano-porous structures form in GaSb after ion irradiation with 185 MeV Au ions. The porous layer formation is governed by the dominant electronic energy loss at this energy regime. The porous layer morphology differs significantly from that previously reported for low-energy, ion-irradiated GaSb. Prior to the onset of porosity, positron annihilation lifetime spectroscopy indicates the formation of small vacancy clusters in single ion impacts, while transmission electron microscopy reveals fragmentation of the GaSb into nanocrystallites embedded in an amorphous matrix. Following this fragmentation process, macroscopic porosity forms, presumably within the amorphous phase.

36 MATERIALS SCIENCE↗

Grain size effect on the giant dielectric constant of CaCu{sub 3}Ti{sub 4}O{sub 12} nanoceramics prepared by mechanosynthesis and spark plasma sintering

In the present work, CaCu{sub 3}Ti{sub 4}O{sub 12} (CCTO) nanoceramics with different grain sizes were prepared by spark plasma sintering (SPS) at different temperatures (SPS-800, SPS-900, SPS-975, and SPS-1050) of the mechanosynthesized nano-powder. Structural and microstructural properties were studied by XRD and field-emission scanning electron microscope measurements. The grain size of CCTO nanoceramics increases from 80 nm to ∼200 nm for the ceramics sintered at 800 °C and 975 °C, respectively. Further increase of SPS temperature to 1050 °C leads to micro-sized ceramics of 2–3 μm. The electrical and dielectric properties of the investigated ceramics were studied by impedance spectroscopy. Giant dielectric constant was observed in CCTO nanoceramics. The dielectric constant increases with increasing the grain size of the nanoceramics with values of 8.3 × 10{sup 3}, 2.4 × 10{sup 4}, and 3.2 × 10{sup 4} for SPS-800, SPS-900, and SPS-975, respectively. For the micro-sized SPS-1050 ceramics, the dielectric constant dropped to 2.14 × 10{sup 4}. The dielectric behavior is interpreted within the internal barrier layer capacitance picture due to the electrical inhomogeneity of the ceramics. Besides the resistive grain boundaries that are usually observed in CCTO ceramics, domain boundaries appear as a second source of internal layers in the current nanoceramics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electrical bending actuation of gold-films with nanotextured surfaces

An actuating material system comprising a gold-film with nanotextured surface was fabricated. Using electroless gold plating onto a substrate of porous anodized aluminum oxide, a thin film of gold with a high density of short gold nanofibers on its surface was made. When one end of such a film was connected to an ion generator, bending was achieved upon electrical charging in air. Experiments showed that the free end of an 8 mm film could be displaced by more than 1.6 mm with a bending strain of 0.08%. In contrast with other types of thin-film artificial muscle materials, the present Au-film did not require any electrolyte to function. With the relatively easy fabrication method, this nanotextured film shows promising actuation behavior in air. Actuation systems based on a number of mechanisms have been developed in the last few decades, including electric, ionic, photonic, pneumatic, and thermal. As discussed in detail in Madden et al. and Brochu and Pei,11 the weaknesses of these materials include bulkiness, low stress or strain generation, low strain rate, long response time, short cycle life, and low energy efficiency. Recent developments have involved the possibilities to use the unique properties of nanostructures to produce actuation, such as in nanostructured carbon, nanoporous gold or platinum, V 2 O 5 nanofibre sheet, electroactive nanostructured polymers, hybrid carbon nanotube yarn, niobium nanowire yarn, and anodized aluminum oxide (AAO). Here, we introduce a nanostructured material system comprising a gold film with a high density of short gold-nanofibers attached to one side, which can bend to produce a large displacement (~1.6 mm) upon electrical charging through an ion generator. In addition to the displacement, the functionality without the need of an electrolyte is another advantage for using this material system as actuators. We discuss the fabrication and characterization methods, the morphology, and the actuating properties of this system here. To achieve a metal film with a nanotextured surface, electroless gold-plating was performed on substrates of AAO with a characteristic nano-honeycomb structure consisting of >10 10 pores per cm 2 . The fabrication of the AAO substrates followed the procedures described in Cheng and Ngan. The anodization condition for the AAO was 40 V against graphite electrode in saturated oxalic acid at 18 °C for 2 h. The pore diameter observed was 50 ± 5 nm. By using an electroless gold-plating method described by Kohli et al.,22 gold in short nanofiber form was deposited into the pores of the AAO template. As shown in Figs. 1(a) and 1(b), in addition to partially filling the pores with gold, the top surface of the AAO template was coated with a thin gold film (~100 nm) of Au. A ~30 μm layer of lacquer was then painted on the top of the thin gold film to serve as a supporting layer.

42 ENGINEERING↗

Ar plasma treated ZnON transistor for future thin film electronics

To achieve high-mobility and high-reliability oxide thin film transistors (TFTs), ZnON has been investigated following an anion control strategy based on the substitution of oxygen with nitrogen in ZnO. However, as nitrogen possesses, compared to oxygen, a low reactivity with Zn, the chemical composition of ZnON changes easily, causing in turn a degradation of both the performance and the stability. Here, we have solved the issues of long-time stability and composition non-uniformity while maintaining a high channel mobility by adopting the argon plasma process, which can delay the reaction of oxygen with Zn–O–N; as a result, owing to the formation of very fine nano-crystalline structure in stable glassy phase without changes in the chemical composition, the material properties and stability under e-radiation have significantly improved. In particular, the channel mobility of the ZnON TFTs extracted from the pulsed I−V method was measured to be 138 cm{sup 2}/V s.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A comprehensive simulation model of the performance of photochromic films in absorbance-modulation-optical-lithography

Optical lithography is the most prevalent method of fabricating micro-and nano-scale structures in the semiconductor industry due to the fact that patterning using photons is fast, accurate and provides high throughput. However, the resolution of this technique is inherently limited by the physical phenomenon of diffraction. Absorbance-Modulation-Optical Lithography (AMOL), a recently developed technique has been successfully demonstrated to be able to circumvent this diffraction limit. AMOL employs a dual-wavelength exposure system in conjunction with spectrally selective reversible photo-transitions in thin films of photochromic molecules to achieve patterning of features with sizes beyond the far-field diffraction limit. We have developed a finite-element-method based full-electromagnetic-wave solution model that simulates the photo-chemical processes that occur within the thin film of the photochromic molecules under illumination by the exposure and confining wavelengths in AMOL. This model allows us to understand how the material characteristics influence the confinement to sub-diffraction dimensions, of the transmitted point spread function (PSF) of the exposure wavelength inside the recording medium. The model reported here provides the most comprehensive analysis of the AMOL process to-date, and the results show that the most important factors that govern the process, are the polarization of the two beams, the ratio of the intensities of the two wavelengths, the relative absorption coefficients and the concentration of the photochromic species, the thickness of the photochromic layer and the quantum yields of the photoreactions at the two wavelengths. The aim of this work is to elucidate the requirements of AMOL in successfully circumventing the far-field diffraction limit.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗