Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Membrane”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An experimental study on dehumidification and regeneration performance of a new nonporous membrane-based heat and mass exchanger using an ionic liquid desiccant

As a promising alternative to inefficient vapor-compression-based air conditioning, liquid desiccant dehumidification uses a liquid desiccant in contact with the humid air absorbing the moisture. However, it has not gained much market share due to the issues related to the carryover, corrosion, fouling, and crystallization of liquid desiccant. The research has developed a new membrane-based exchanger, which uses a non-corrosive ionic liquid desiccant and nonporous tubular membranes to address these issues. As the second generation of the prototype, the new exchanger was tested at various operating conditions. According to the experimental data, when it is used in the dehumidification loop, the new membrane-based exchanger achieves a specific vapor transportation rate of 778.6 g/(h–m 2 ) and an average water vapor flux of 0.316 g/(h-m 2 -Pa), which is a significant improvement compared with the previous designs using nonporous membranes. It also achieved a comparable or even better dehumidification performance compared with the dehumidifiers that use porous membrane and conventional liquid desiccants. However, the regeneration performance is not as good as its dehumidification. It is mainly caused by the high operating temperature required in the regeneration loop. The experimental data and findings provide first-hand experimental data and enhance the understanding of advanced membrane-based ionic liquid desiccant systems.

42 ENGINEERING↗
DOE OSTI2022

Estimating the energy requirement for hydrogen production in proton exchange membrane electrolysis cells using rapid operando hydrogen crossover analysis

Hydrogen (H 2 ) crossover in proton exchange membrane water electrolyzers refers to the process by which hydrogen produced at the cathode traverses the membrane and mixes with the oxygen produced at the anode. This phenomenon reduces efficiency and may pose flammability hazards. In this work we present a method for quantifying the H 2 content of the anode exhaust gas using a gas chromatograph that is capable of sampling data every 2 min. Subsequent theory is presented to calculate the crossover flux, overall H 2 efficiency, and H 2 energy requirements. Results the effects of membrane thickness using Nafion TM N117 (178 um) and Nafion TM NR212 (51 um) membranes. Furthermore, it was found that thinner membranes lead to improved VI performance but exhibit higher crossover rates. Despite their increased crossover, leading to decreased hydrogen efficiency, the calculated required energy for NR212 membrane-electrode assemblies (MEAs) was significantly lower than that of N117 MEAs.

08 HYDROGEN↗
DOE OSTI2020

Fabrication of high-performance gas-diffusion-electrode based membrane-electrode assemblies

This paper demonstrates the fabrication and processing steps required to produce high performance fuel cell membrane electrode assemblies (MEAs) based on spray-coated gas-diffusion electrodes (GDEs). It is demonstrated that coating the catalyst layer with a thin layer of ionomer and then hot pressing the GDEs to the membrane is required to achieve comparable catalyst activity and air performance to catalyst-coated-membrane MEAs. We show that there is a critical amount of ionomer required to achieve maximized performance. Using electron microscopy, we show that the combination of the ionomer overlayer and hot-pressing bonds the catalyst layer to the membrane, increasing the interfacial contact area and quality of this interface. We also find that the ionomer overlayer smooths the surface of the GDE and provides increased contact area between the GDE and the membrane. Additionally, we demonstrate that much less ionomer is required for high-performance than has been previously reported. Through model fitting of electrochemical impedance spectroscopy, we show that this improvement in the catalyst layer - membrane interface reduces the effective catalyst layer resistance, which reduces Ohmic losses and increases catalyst utilization.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

La–Sr–Co oxide catalysts for oxygen evolution reaction in anion exchange membrane water electrolyzer: The role of electrode fabrication on performance and durability

Anion exchange membrane water electrolysis is an attractive technology for low-cost generation of “green” hydrogen by combining the use of noble metal-free catalysts with pure water feed. By thus addressing main drawbacks of the liquid alkaline electrolysis and proton exchange membrane water electrolysis, anion exchange membrane water electrolysis stands an excellent chance of replacing the two technologies. The development of active and stable platinum group metal (PGM)-free catalysts for oxygen evolution reaction (OER) is crucial for making anion exchange membrane water electrolyzers (AEMWEs) practical. For this work, we synthesized, characterized and tested two La–Sr–Co oxide-based OER catalysts. First, we characterized the catalysts by XRD, SEM, and N 2 physisorption and assessed their OER activity in a three-electrode cell. Next, we focused on electrode fabrication, demonstrating the importance of catalyst-ink application to the porous transport layers (PTLs) and a key role of adding a binder to the catalyst ink to prevent the catalyst detachment from the PTL in pure water. We tested three membrane electrode assemblies prepared using different formulations of the anode catalyst ink. The results show that the optimum ink formulation is essential for the performance on pure-water feed by maximizing OH - conductivity of the catalyst layer and catalyst-membrane interface.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Molecular layer deposition (MLD) modified SSZ-13 membrane for greatly enhanced H 2 separation

Zeolite membranes with high thermal stability and well-fined pores are attractive for gas separation. However, the defects are almost inevitable in zeolite membranes. Moreover, fine-tuning zeolitic pores for precise molecular separation is challenging. In this study, molecular layer deposition (MLD) was employed to deposit ultrathin microporous coating on SSZ-13 zeolite membrane. The MLD modified SSZ-13 composite membrane was highly selective for H 2 separation. With optimized MLD cycles, H 2 /N 2 and H 2 /CH 4 ideal selectivities as high as 35.6 and 427, respectively, were obtained, in strong contrast with approximately 5 for base SSZ-13 membrane. Our results suggest that MLD is a very promising technology to precisely modify the pore size of zeolite membranes, while minimizing flow through non-selective defects, for gas separation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Enhancing membrane performance for CO 2 capture from flue gas with ultrahigh MW polyvinylamine

Membranes for post-combustion CO 2 capture are required to have a high CO 2 permeance due to the limited driving force. For facilitated transport membranes synthesized with polyvinylamine (PVAm), a defect-free selective layer of <200 nm is usually required to render sufficient permeance with high CO 2 /N 2 selectivity. In order to meet such a demand through the knife-coating process, the coating solution needs to have a high viscosity at a relatively low concentration to minimize its penetration into the substrate. The demand was met by synthesizing PVAm with an ultrahigh molecular weight (MW) via inverse emulsion polymerization (IEP) in this study. Compared to solution polymerization, IEP isolates the reaction in inverse micelles suspended in a continuous organic phase, which allows excellent dissipation of the heat generated by the reaction and reduces gel formation drastically. The polymerization parameters, including monomer concentration, initiator concentration, and reaction temperature, were investigated to obtain the optimal MW of PVAm for membrane performance. As compared to solution polymerization, IEP enhanced the MW of PVAm from 1.2 to 12.7 MDa, which minimized the penetration of the coating solution into the substrate and hence the extra mass transfer resistance. The effect of MW and degree of hydrolysis of PVAm on the membrane transport properties were studied. Furthermore, by employing PVAm with a MW of 12.7 MDa to strengthen the polymer matrix, the loading of piperazine glycinate in the membrane was increased up to 85 wt.%. In conclusion, the resultant membrane achieved a CO 2 permeance of 839 GPU and a CO 2 /N 2 selectivity of 161 at the typical flue gas temperature of 57°C.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

PBI nanofiber mat-reinforced anion exchange membranes with covalently linked interfaces for use in water electrolysers

Anion exchange membranes (AEM) are key components in anion exchange membrane water electrolysers. Recently developed materials are less susceptible to the alkaline degradation of the polymer backbone and quaternary ammonium groups. A remaining challenge is the mechanical stability in contact with hot water and dimensional stability when the temperature of the feed solution changes. One solution is to reinforce membranes with a porous support. Since support materials like PEEK or PTFE have a different swelling behavior than the matrix and no strong interactions with the matrix, voids can form, and gas crossover increases. In this work, we approach this issue by pore filling polybenzimidazole nanofiber mats with the bromomethylated precursor of mTPN, an ultra-stable AEM material. During drying, a covalent interaction between support (PBI amine groups) and matrix (-CH 2 Br) is established. After quaternization, the optimized PBI/mTPN-50.120 composite membrane still shows a high conductivity of 62 mS cm –1 , but 37% reduced length swelling in comparison to the non-reinforced membrane. Tensile strength and Young's modulus increase 17% and 56% to 49 MPa and 680 MPa, respectively. In an electrolyser, a stable voltage of 1.98V at 0.25 A cm –2 was achieved, and no change in membrane resistance was observed over the test time of 200 h (50°C, 1 M KOH, catalysts based on Ni/Fe and Mo).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

New sterically hindered polyvinylamine-containing membranes for CO 2 capture from flue gas

Amine-containing facilitated transport membranes can have both high permeability and selectivity due to the reversible reaction between CO 2 and amino groups for effective carbon capture from flue gas. In this study, we have developed an improved method for the synthesis of high-molecular-weight sterically hindered polyvinylamine (PVAm) as the new fixed-site carrier in thin-film composite membranes for CO 2 capture. Commercially available PVAm was N-monomethylated into poly-N-methyl-N-vinylamine (PVAm-CH 3 ) using the stepwise reductive amination with a highly polar fluorinated alcohol as the solvent to enhance the equilibrium shift to the formation of the imine intermediate. The method prevented over-alkylation, resulting in the increased yield of the target product. PVAm-CH 3 exhibited excellent CO 2 facilitation with a CO 2 permeability of 445.7 Barrer (1 Barrer = 3.349 x 10 –16 mol m m –2 s –1 Pa –1 ) and a CO 2 /N 2 selectivity of 70.3, which are above the Robeson 2008 upper bound. The PVAm-CH 3 solution retained a sufficiently high viscosity after incorporating the aminoacid salt, 2-(1-piperazinyl)ethylamine sarcosinate (PZEA-Sar), as the mobile carrier for the membrane coating on nanoporous polyethersulfone (PES) substrates without any penetration issues. The resultant thin-film composite PVAm-CH3/PZEA-Sar membrane with a thickness of approximately 170 nm exhibited a superior CO 2 performance of 1071 GPU (1 GPU = 3.349 x 10 –10 mol m –2 s –1 Pa –1 ) and a CO 2 /N 2 selectivity of 183 at 57°C and a feed gas pressure of 111.64 kPa (1.5 psig). This PVAm-CH 3 /PZEA-Sar membrane surpassed the latest redefined 2019 CO 2 /N 2 upper bound and outperformed other polymer-based membranes. Density functional theory calculations also demonstrated that PVAm-CH 3 showed a stronger preference, relative to PVAm, toward the more efficient bicarbonate pathway. Thus, the steric hindrance effect of PVAm-CH 3 enhanced the solubility of CO 2 in the polymer matrix and resulted in the higher CO 2 permeance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Salt and ion transport in a series of crosslinked AMPS/PEGDA hydrogel membranes

Salt permeability and ionic conductivity are critical properties for membranes in water purification and energy applications. Both properties depend on individual ion sorption and diffusion coefficients, which are significantly influenced by polymer chemical and physical parameters such as fixed charge concentration and membrane water content. However, systematic studies connecting polymer structure to ion transport properties are still lacking. In this study, a series of uncharged and charged membranes were synthesized using poly(ethylene glycol) diacrylate (PEGDA) as a cross-linker and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) as a charged monomer. Membrane fixed charge concentration and water uptake were systematically varied by adjusting AMPS content in the pre-polymerization mixture. Salt sorption and permeability coefficients and ionic conductivity of these membranes were measured as a function of NaCl solution concentration (0.01–1 M). Combining the solution-diffusion model and Nernst-Planck equation, individual ion diffusion coefficients were calculated. Experimental Na + diffusion coefficients for all materials were well described by the Mackie and Meares tortuosity model, highlighting the strong influence of water content on ion diffusivity in both uncharged and charged polymers. Model predictions for Cl – diffusion coefficients agree reasonably well with experimental values, with some deviations occurring in more highly charged membranes. Finally, this discrepancy might result from interactions not captured by the Mackie and Meares model (e.g., fixed charge-ion interactions).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Fabrication and accelerated long-term stability test of asymmetrical hollow fiber-supported thin film oxygen separation membrane

Asymmetrical hollow fiber-supported thin film membrane may provide microstructural advantages for air separation and oxygen production. The fabrication of such a membrane is usually very difficult, particularly the sintering behaviors and thermal expansion coefficient (TEC) mismatch among multiple layers. This directly affects the reliability and long-term stability of the membrane. Here, in this research, the sintering behaviors of a set of simple oxides are systematically studied and ZnO is identified as a material component for composite substrate La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF)-ZnO. The LSCF-ZnO ratios are further optimized by trading off several factors, e.g., matching the sintering behaviors and TECs of the LSCF-ZnO composite with those of LSCF thin film separation layer while enhancing the substrate strength. With the identified LSCF-ZnO ratio, the LSCF-ZnO composite hollow fiber substrate precursor is formed through slurry spinning process with porous microstructure being formed via phase inversion process. The thin film LSCF dense separation layer is then dip-coated on the substrate followed by co-sintering process. A thin, porous PrBaCo(Fe 0.6 Zr 0.2 Y 0.2 )O 5+δ (PBCFZY) catalyst layer is fabricated on the dense LSCF separation layer with dip-coating and sintering process, forming an asymmetrical membrane device LSCF-ZnO/LSCF/PBCFZY. Oxygen permeation test of the device is systematically conducted, and the fundamental mechanisms are analyzed. An accelerated long-term stability test of the membrane is also conducted (~550h, 46 thermal cycling loads), demonstrating excellent robustness and durability. The device is characterized and analyzed before and after the test. By replacing a considerable amount of high cost LSCF with low cost ZnO in the substrate, it not only enhances the stability but also reduces the capital cost of the membrane for practical applications.

42 ENGINEERING↗
DOE OSTI2022

Inadequacy of current approaches for characterizing membrane transport properties at high salinities

Cost optimal design of osmotic membrane processes requires an accurate estimate of membrane transport parameters across their full operational range. However, standard approaches for estimating these parameters rely on empirical methods, the accuracy of which remains unquantified as a function of temperature, salinity, and measurement error. Herein, we present a systematic accuracy analysis of previously developed methods for estimation of membrane transport properties in reverse osmosis, high-pressure reverse osmosis, forward osmosis, pressure retarded reverse osmosis, and osmotically assisted reverse osmosis. We use a Monte Carlo approach to sample the full range of feasible membrane water permeabilities, salt permeabilities, structural parameters, and operating conditions for these processes. These material and process parameters are then incorporated into a physical transport model for each process. Our analysis shows that the statistical uncertainty of current empirical methods for estimating membrane parameters increases by 5 times from low-salinity to high-salinity conditions. Here, the result of this work demonstrates that empirical methods are inadequate for precisely estimating membrane transport properties at high salinity and highlight a critical need for the development of statistically validated higher accuracy methods.

42 ENGINEERING↗
DOE OSTI2022

Application of GO anchored mediator in a polymer electrolyte membrane for high-rate solid-state supercapacitors

Here, we synthesized a novel polymer electrolyte membrane by combining poly (vinylidene fluoride) (PVDF) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) with graphene oxide (GO) nanosheets and a lithium salt of tungstosilicic acid (Li 4 SiW 12 O 40 , hereafter, referred to SiWLi). The impact of the addition of GO/SiWLi on the microstructure and morphology of the membrane were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). We found that adding the GO/SiWLi to the PVDF/LiTFSI polymer electrolyte membrane significantly reduced the pore size. Furthermore, the addition of the GO/SiWLi resulted in not only an increase of the ionic conductivity from 0.87 $\times$ 10 –2 to 3.12 $\times$ 10 –2 Scm –1 but also an increase in the lithium-ion transference number from 0.52 to 0.87. The polymer electrolyte membranes with and without GO/SiWLi were utilized to fabricate solid-state supercapacitors. The supercapacitors fabricated with the membrane containing GO/SiWLi displayed 37.2% lower equivalent series resistance and 88.2% greater specific capacitance than those fabricated using the membrane without GO/SiWLi at 200mVs –1 .

42 ENGINEERING↗
DOE OSTI2023

Highly tunable structure-by-design polymer brush membranes for organic solvent nanofiltration

Synthetic polymeric nanofiltration membrane processes offer an alternate low-energy option to energy-intensive distillation to fractionate similar size organic solvents for chemical, petroleum, food and biotechnology industries. Here, in this study, we synthesize and test a new class of structure-by-design hydrophilic polymeric brush membranes, that address the limitations of commercial polymer membranes, are tunable and exhibit commercially relevant filtration performance. Because these brush membranes are grafted by Single Electron Transfer-Living Radical Polymerization (SET-LRP) and replace statistically random phase inversion or interfacial polymerization used for synthesizing commercial polymer membranes, their porous structure can be remodeled by varying their morphology and chemistry. We graft hydroxyethyl methacrylate (HEMA) brush structures with short and long crosslinkers, demonstrate two competing phenomena - pore stiffening and opening - and obtain high selectivity at reasonable permeability for commercially relevant methanol/toluene separation. This new class of stable, tunable, and scalable membranes offers exciting opportunities to reduce energy for separation of organic solvents.

42 ENGINEERING↗
DOE OSTI2025

Electrostatic limits on charge selectivity in ultrahigh charge density polymer membranes

Ion-exchange membranes (IEMs) with ultrahigh charge densities offer the promise of enhanced ion transport for electrochemical technologies, yet the fundamental limits of this membrane design strategy are not yet understood. In this work, we present a systematic study of bis(1-vinyl-3-imidazolium) cross-linked polymer membranes with fixed charge contents ranging from 6 to 9 mol/L[dry polymer], synthesized to isolate the effects of charge density at constant membrane water content. While ionic conductivity increases monotonically with increasing charge density, a sharp decline in charge selectivity is observed for the most densely charged membranes, defying conventional expectations. Structural, thermal, and mechanical analyses reveal a critical onset of network disruption and anomalous ion partitioning behavior in these densely charged membranes. With proper consideration of cross-linker geometry, these results are interpreted using Manning's counter-ion condensation theory, which suggests that closely packed charged cross-linkers amplify inter-chain electrostatic interactions and trigger excess counter-ion condensation. Our findings suggest that, beyond a threshold spacing between fixed charges, increased functionalization may harm rather than help charge selectivity of IEMs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

PLAT domain protein 1 (PLAT1/PLAFP) binds to the Arabidopsis thaliana plasma membrane and inserts a lipid

Robust agricultural yields depend on the plant's ability to fix carbon amid variable environmental conditions. Over seasonal and diurnal cycles, the plant must constantly adjust its metabolism according to available resources or external stressors. The metabolic changes that a plant undergoes in response to stress are well understood, but the long-distance signaling mechanisms that facilitate communication throughout the plant are less studied. The phloem is considered the predominant conduit for the bidirectional transport of these signals in the form of metabolites, nucleic acids, proteins, and lipids. Lipid trafficking through the phloem in particular attracted our attention due to its reliance on soluble lipid-binding proteins (LBP) that generate and solubilize otherwise membrane-associated lipids. The Phloem Lipid-Associated Family Protein (PLAFP) from Arabidopsis thaliana is generated in response to abiotic stress as is its lipid-ligand phosphatidic acid (PA). PLAFP is proposed to transport PA through the phloem in response to drought stress. To understand the interactions between PLAFP and PA, nearly 100 independent systems comprised of the protein and one PA, or a plasma membrane containing varying amounts of PA, were simulated using atomistic classical molecular dynamics methods. In these simulations, PLAFP is found to bind to plant plasma membrane models independent of the PA concentration. When bound to the membrane, PLAFP adopts a binding pose where W41 and R82 penetrate the membrane surface and anchor PLAFP. This triggers a separation of the two loop regions containing W41 and R82. Subsequent simulations indicate that PA insert into the β -sandwich of PLAFP, driven by interactions with multiple amino acids besides the W41 and R82 identified during the insertion process. Finally, fine-tuning the protein-membrane and protein-PA interface by mutating a selection of these amino acids may facilitate engineering plant signaling processes by modulating the binding response.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

A mathematical design framework for membrane pre-concentration in energy-efficient recovery of fermentation products

Due to the dilute nature of products manufactured via fermentation and cell-free bioprocessing, dewatering is a common unit operation in downstream processing (DSP) for bioproduct recovery, but it is typically energy intensive. To improve DSP energy efficiency for bio-based small molecules, integrating high-pressure membrane pre-concentration is a promising process option. However, this approach is typically constrained by a tradeoff between concentration factor (CF) and product recovery (PR), namely increasing the CF typically results in greater product loss, and vice versa. Here we developed a model that enables process design guidelines to: (i) identify scenarios in which the additional energy consumption and product loss from membrane pre-concentration are justified for use in DSP, and (ii) determine the optimal CF that minimizes process specific energy consumption. We compared the energy consumption of high-pressure membrane-integrated processes to evaporation-only processes and applied the model to an experimental case study for the separation and purification of butyric acid from Clostridium tyrobutyricum fermentation using an in situ product recovery (ISPR) process. The model estimated that integrating a tangential-flow reverse osmosis (RO) pre-concentration unit could reduce process energy consumption up to 45%. The use of advanced membrane pre-concentration technologies, such as negative rejection membranes and organic solvent reverse osmosis (OSRO), have the potential to further reduce the overall process specific energy consumption up to 96%, projected based on modeling. Overall, membrane pre-concentration, especially when strategically integrated prior to an evaporation step with optimized process conditions, holds significant potential for improving DSP energy efficiency, particularly in applications requiring substantial solvent removal for product recovery from dilute mixtures.

09 BIOMASS FUELS↗
DOE OSTI2024

Gas Permeation and Separation Characteristics of Microporous TpHz COF Membranes Synthesized by Substrate-Assisted Interfacial Polymerization

Microporous two-dimensional covalent organic framework (2D COF) membranes offer promise for gas separation applications, but their gas transport mechanism remains unclear. In this study, a TpHz 2D COF membrane supported on a macroporous nylon substrate is prepared by substrate-assisted interfacial polymerization under mild conditions. The formation of a continuous and dense thin (~300 nm thick) TpHz layer is confirmed by scanning electron microscopy and Fourier transform infrared spectroscopy. Characterization by X-ray diffraction, grazing incidence wide-angle X-ray scattering, and N 2 porosimetry qualitatively reveals the microstructures of the supported TpHz membranes, i.e., they comprise partially oriented 2D COF lamellar crystallites with moderate crystallinity in an eclipsed (AA) stacking geometry, centering the effective membrane pore size distribution at ~1.1 nm. Further, single gas permeation data show that the transport of common molecular gases, including H 2 , He, CH 4 , N 2 , and CO 2 , through the synthesized TpHz membranes follows the Knudsen transport mechanism, where single gas permeance decreases with an increasing molecular weight and permeation temperature. Binary gas separation results show that in the equimolar CO 2 /N 2 mixture, the presence of the CO 2 surface flow slightly hinders the N 2 flow at room temperature due to the reduced membrane channel size by the adsorbed CO 2 gas layer on TpHz’s pore wall. In contrast, permeation of the equimolar CH 4 /N 2 binary mixture does not exhibit a discernible surface flow of both gases due to their much lower gas uptake on TpHz, and their transport mechanism follows Knudsen-like behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Single-Molecule Fluorescence Investigations of Solute Transport Dynamics in Nanostructured Membrane Separation Materials

Many materials used for membrane separations comprise of nanoscale structures such as pores and domains. Such nanostructures often control the solute permeability and selectivity of separation membranes. Thus, for future development of highly efficient separation membranes, it is important to understand the structural and chemical properties of these nanostructures, and also their influences on solute transport dynamics. For the last two decades, single-molecule fluorescence techniques have been used to measure the detailed dynamics of solute molecules diffusing in various nanostructured materials, giving valuable insights into molecular transport mechanisms influenced by nanoscale material heterogeneity. This Perspective will discuss recent single-molecule fluorescence studies on solute diffusion in materials relevant to membrane separations, including dense polymer films and nanoporous materials. These studies have revealed the formation and properties of nanostructures, and unique transport dynamics of solute molecules manipulated by their confinement and partitioning to the nanostructures, which play key roles in membrane separations. Furthermore, this Perspective will also point out scientific challenges toward thorough understanding of molecular-level mechanisms in membrane separations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗