Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MODULE ENCAPSULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

The Array Automated Assembly Task for the Low Cost Solar Array Project, Phase 2

During the program a process sequence was proposed and tested for the fabrication of dendritic welb silicon into solar modules. This sequence was analyzed as to yield and cost and these data suggest that the price goals of 1986 are attainable. Specifically, it was shown that a low cost POCL3 is a suitable replacement for the semiconductor grade, and that a suitable CVD oxide can be deposited from a silane/air mixture using a Silox reactor. A dip coating method was developed for depositing an antireflection coating from a metalorganic precursor. Application of photoresist to define contact grids was made cost effective through use of a dip coating technique. Electroplating of both Ag and Cu was shown feasible and cost effective for producing the conductive metal grids on the solar cells. Laser scribing was used to separate the cells from the dendrites without degradation. Ultrasonic welding methods were shown to be feasible for interconnecting the cells. A study of suitable low cost materials for encapsulation suggest that soda lime glass and phenolic filled board are preferred.

Campbell, R. B.↗

Advanced packaging for Integrated Micro-Instruments

The relationship between packaging, microelectronics, and micro-electrical-mechanical systems (MEMS) is an important one, particularly when the edges of performance boundaries are pressed, as in the case of miniaturized systems. Packaging is a sort of physical backbone that enables the maximum performance of these systems to be realized, and the penalties imposed by conventional packing approaches is particularly limiting for MEMS devices. As such, advanced packaging approaches, such as multi-chip modules (MCM's) have been touted as a true means of electronic 'enablement' for a variety of application domains. Realizing an optimum system of packaging, however, in not as simple as replacing a set of single chip packages with a substrate of interconnections. Research at Phillips Laboratory has turned up a number of integrating options in the two- and three-dimensional rending of miniature systems with physical interconnection structures with intrinsically high performance. Not only do these structures motivate the redesign of integrated circuits (IC's) for lower power, but they possess interesting features that provide a framework for the direct integration of MEMS devices. Cost remains a barrier to the application of MEMS devices, even in space systems. Several innovations are suggested that will result in lower cost and more rapid cycle time. First, the novelty of a 'constant floor plan' MCM which encapsulates a variety of commonly used components into a stockable, easily customized assembly is discussed. Next, the use of low-cost substrates is examined. The anticipated advent of ultra-high density interconnect (UHDI) is suggested as the limit argument of advanced packaging. Finally, the concept of a heterogeneous 3-D MCM system is outlined that allows for the combination of different compatible packaging approaches into a uniformly dense structure that could also include MEMS-based sensors.

Lyke, James L.↗

CH 4 steam reforming on Pt + Pd/Al 2 O 3 monolith: impact of Mn 0.5 Fe 2.5 O 4 spinel addition

The performance of Pt + Pd/Al 2 O 3 monolith catalysts was analyzed under a feed (H 2 + CO + CH 4 + NO + O 2 + H 2 O + CO 2 ) simulating the exhaust gas of stoichiometric natural gas vehicles (NGVs). The flow reactor results show enhanced low temperature (<400 °C) CH 4 oxidation activity under cyclic lean/rich feed modulation and with Mn 0.5 Fe 2.5 O 4 (MFO) spinel addition to the platinum group metal (PGM) catalyst. In the absence of the MFO spinel, the PGM catalyst can achieve full CH 4 conversion, but the presence of spinel in the catalyst limits the high temperature (>500 °C) CH 4 conversion. The depletion of gas phase O 2 , as indicated by the detection of products CO and H 2 in the reactor effluent at higher temperature and CH 4 conversion, portends the emergence of steam reforming of CH 4 (SRM). To investigate the cause of the detrimental impact of spinel under the high temperature, net rich regime, we show through a combination of SRM experiments and post-reaction catalyst characterization that SRM is negatively impacted by the accumulation of Mn and Fe spinel species on the PGM catalyst. This is due to the migration of the base metal species and potential encapsulation and blockage of PGM active sites. The latter is supported by density functional theory (DFT) calculations that indicate favorable metal oxide decoration of active Pt step sites. Lastly, a zoned catalyst design is developed that mitigates the detrimental metals migration while exploiting the methane conversion enhancement afforded by spinel oxides under oxygen rich conditions.

03 NATURAL GAS↗

Crystalline Silicon Photovoltaic Module Manufacturing Costs and Sustainable Pricing: 1H 2018 Benchmark and Cost Reduction Road Map

In this paper we provide an overview of the accounting methods and most recent input data used within NREL's bottom-up crystalline silicon (c-Si) solar photovoltaic (PV) module supply chain cost models. The costs accounting framework that is detailed in this paper provides a methodology to prepare bottom-up c-Si PV supply chain cost models in accordance with the U.S. Generally Accepted Accounting Principles (GAAP) and the International Financial Reporting Standards (IFRS). For the polysilicon, ingot, wafer, cell conversion, and module assembly steps of the c-Si supply chain, we outline what is relevant for calculations of the costs of goods sold (consisting of the materials, labor, electricity, maintenance, and depreciation of capital equipment); as well as the additional operating expenses of research and development (R&D); and sales, general, and business administration (S, G, &A). This 2017 benchmark analysis is applied to current state-of-the-art manufacturing sites located within the United States, China, Taiwan, South Korea, Malaysia, the Philippines, and Germany. Primarily due to country-dependent labor and electricity rates, tax rates, and cost-of-capital considerations, we calculate differences in minimum sustainable pricing for all of these countries. In this paper we also include technical descriptions and bottom-up cost model results for several emerging c-Si technologies including larger Czochralski (Cz) ingots, kerfless wafers, reduced silicon utilization by thinner wafers and advanced diamond wire wafering, new encapsulants and backsheets, shingled cells, and the cell architectures passivated emitter and rear cells (PERC), bifacial passivated emitter and rear totally diffused (PERT) cells, bifacial heterojunction intrinsic thin layer (HIT) cells, and interdigitated all back-contact cells (IBC).

14 SOLAR ENERGY↗

Kinetic Growth of Multicomponent Microcompartment Shells

An important goal of systems and synthetic biology is to produce high value chemical species in large quantities. Microcompartments, which are protein nanoshells encapsulating catalytic enzyme cargo, could potentially function as tunable nanobioreactors inside and outside cells to generate these high value species. Modifying the morphology of microcompartments through genetic engineering of shell proteins is one viable strategy to tune cofactor and metabolite access to encapsulated enzymes. However, this is a difficult task without understanding how changing interactions between the many different types of shell proteins and enzymes affect microcompartment assembly and shape. Here, we use multiscale molecular dynamics and experimental data to describe assembly pathways available to microcompartments composed of multiple types of shell proteins with varied interactions. As the average interaction between the enzyme cargo and the multiple types of shell proteins is weakened, the shell assembly pathway transitions from (i) nucleating on the enzyme cargo to (ii) nucleating in the bulk and then binding the cargo as it grows to (iii) an empty shell. Atomistic simulations and experiments using the 1,2-propanediol utilization microcompartment system demonstrate that shell protein interactions are highly varied and consistent with our multicomponent, coarse-grained model. Furthermore, our results suggest that intrinsic bending angles control the size of these microcompartments. Altogether, our simulations and experiments provide guidance to control microcomparmtent size and assembly by modulating the interactions between shell proteins.

defects↗

Transparent Metal–Organic Framework/Polymer Mixed Matrix Membranes as Water Vapor Barriers

Preventing the permeation of reactive molecules into electronic devices or photovoltaic modules is of significant concern to ensure their life span and reliability. Our report is focused on the formation of highly functioning barrier films based on nanocrystals (NCs) of a water-scavenging metal-organic framework (MOF) and a hydrophobic cyclic olefin copolymer (COC) to overcome the current limitations. Water vapor transmission rates (WVTR) of the films reveal a 10-fold enhancement in the WVTR compared to the substrate while maintaining outstanding transparency over most of the visible and solar spectrum, a necessary condition for integration with optoelectronic devices.

36 MATERIALS SCIENCE↗

Deep Understanding of Strong Metal Interface Confinement: A Journey of Pd/FeO x Catalysts

Tuning the atomic interface configuration of noble metals (NMs) and transition-metal oxides is an effective straightforward yet challenging strategy to modulate the activity and stability of heterogeneous catalysts. Herein, Pd supported on mesoporous Fe 2 O 3 with a high specific surface area was rationally designed and chosen to construct the Pd/iron oxide interface. As a versatile model, the physicochemical environments of Pd nanoparticles (NPs) could be precisely controlled by taming the reduction temperature. The experimental and density functional theory calculation results unveiled that the catalyst in the support–metal interface confinement (SMIC) state showed significantly enhanced catalytic activity and sintering resistance for CO oxidation. The constructed Fe sites at the interfaces between FeO x overlayers and Pd NPs not only provided additional coordinative unsaturated ferrous sites for the adsorption and activation of O 2 , thereby facilitating the activation efficiency of O 2 , but also impressively changed the reaction pathway of CO oxidation. As a result, the catalyst followed the Pd/Fe dual-site mechanism instead of the classical Mars–van Krevelen mechanism. For the catalyst in the strong metal–support interaction (SMSI) state, its catalytic activity was seriously suppressed because of the excessive encapsulation of the active Pd sites by FeO x overlayers. Thus, the present study therefore provides detailed insights into the SMIC and SMSI in ferric oxide-supported Pd catalysts, which could guide the preparation of highly efficient supported catalysts for practical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Macrophage infiltration regulates the adipose ECM reconstruction and the fibrosis process after fat grafting

Background: Fat grafting experiences a regeneration process from free lipoaspirate to intact adipose tissue. The adipose extracellular matrixes (ECM) provide the structure and biochemical support for surrounding cells; inflammatory cells, like macrophages, regulate the process. Our hypothesis states that transferred fat undergoes ECM remodeling after fat grafting and this process is regulated by macrophage infiltration. Methods: Lipoaspirate was injected subcutaneously into the back of nude mice. The micro-structure of the fat grafts was observed and evaluated using scanning electron microscope (SEM) and collagen I immunohistostaining. The gene transcription level of collagen proteins and the matrix metalloproteinases (MMPs) were assessed by qRT-PCR. Local injection of clodronate-encapsulated liposome was used to evaluate the role of macrophages of fat grafts at different stages in ECM remodeling, depletion of macrophages, at different time points (Week 1 and Week 4). Results: Results from the SEM analysis showed that liposuction caused severe damage to the ECM structure in freshly aspirated adipose tissue. On Day 1 post-transplantation, the surface of adipocytes was covered with platelets and this secreted fibrin network on the fat grafts. An integral adipose structure was already established with an intact ECM at the end of Week 1. The early depletion of macrophages remarkably hindered ECM reconstruction process by down-regulating the expression of collagen proteins and MMPs. Expression of Collagen I was significantly decreased after depletion of macrophages in both gene and protein levels. Results also showed that the depletion of macrophages at the later stage of fat grafting resulted in less fibrosis and capsule formation. Conclusion: Free fat aspirates undergo a prompt ECM reconstruction process and completed in the first week; this process can be initiated with platelets and mainly modulated by inflammatory cells such as macrophages. It was also observed that prolonged macrophage infiltration contributes to fibrosis and capsule formation in fat grafts. - Highlights: • Free fat aspirates undergo a prompt ECM reconstruction process in the first week. • The ECM reconstruction process is initiated with platelets and modulated by macrophages. • Depletion of macrophage in transferred fat resulted in delayed ECM reconstruction.

60 APPLIED LIFE SCIENCES↗

The Development of a DC Breakdown Voltage Test for Photovoltaic Insulating Materials

The ability of electrical insulating materials within a module to act as insulators is a key safety requirement for PV technology. Direct current breakdown voltage is therefore now specified for relied-upon insulator materials in the IEC 61730-1 safety standard. To fulfill that requirement, a new test method has been developed within the IEC TS 62788-2 backsheet standard for the measurement of breakdown voltage. The development of the test will be described, including the verification of the most critical parameters relative to factors such as defect population(s), dielectric medium, electrode size, electrode surface roughness, maximum current limit, moisture conditioning, number of replicate specimens, rate of voltage rise, specimen thickness, test polarity, and test temperature. Many of these parameters were specifically explored in discovery experiments as the test method was developed. An interlaboratory round-robin (R-R) experiment was conducted to further validate the test method by quantifying its repeatability and reproducibility. The materials examined in the R-R include the backsheet materials: polyethylene terephthalate (PET, two thicknesses), polyvinyl fluoride (PVF), and laminated PVF/PET/PVF ('TPT') as well as the encapsulants poly(ethylene-co-vinyl acetate) (EVA), and polyvinyl butyral (PVB). The precision of the test method as well as key factors contributing to the measurement will be described.

14 SOLAR ENERGY↗

In vivo verification of superficial dose for head and neck treatments using intensity-modulated techniques

Skin dose is one of the key issues for clinical dosimetry in radiation therapy. Currently planning computer systems are unable to accurately predict dose in the buildup region, leaving ambiguity as to the dose levels actually received by the patient's skin during radiotherapy. This is one of the prime reasons why in vivo measurements are necessary to estimate the dose in the buildup region. A newly developed metal-oxide-semiconductor-field-effect-transistor (MOSFET) detector designed specifically for dose measurements in rapidly changing dose gradients was introduced for accurate in vivo skin dosimetry. The feasibility of this detector for skin dose measurements was verified in comparison with plane parallel ionization chamber and radiochromic films. The accuracy of a commercial treatment planning system (TPS) in skin dose calculations for intensity-modulated radiation therapy treatment of nasopharyngeal carcinoma was evaluated using MOSFET detectors in an anthropomorphic phantom as well as on the patients. Results show that this newly developed MOSFET detector can provide a minimal but highly reproducible intrinsic buildup of 7 mg cm{sup -2} corresponding to the requirements of personal surface dose equivalent Hp (0.07). The reproducibility of the MOSFET response, in high sensitivity mode, is found to be better than 2% at the phantom surface for the doses normally delivered to the patients. The MOSFET detector agrees well with the Attix chamber and the EBT Gafchromic registered film in terms of surface and buildup region dose measurements, even for oblique incident beams. While the dose difference between MOSFET measurements and TPS calculations is within measurement uncertainty for the depths equal to or greater than 0.5 cm, an overestimation of up to 8.5% was found for the surface dose calculations in the anthropomorphic phantom study. In vivo skin dose measurements reveal that the dose difference between the MOSFET results and the TPS calculations was on average -7.2%, ranging from -4.3% to -9.2%. The newly designed MOSFET detector encapsulated into a thin water protective film has a minimal reproducible intrinsic buildup recommended for skin dosimetry. This feature makes it very suitable for routine IMRT QA and accurate in vivo skin dosimetry.

61 RADIATION PROTECTION AND DOSIMETRY↗

Protocol for Engineered Compositional Asymmetry Within Nanodiscs

Membrane proteins remain the most challenging targets for structural characterization, yet their elucidation provides valuable insights into protein function, disease mechanisms, and drug specificity. Structural biology platforms have advanced rapidly in recent years, notably through the development and implementation of nanodiscs—discoidal lipid–protein complexes that encapsulate and solubilize membrane proteins within a controlled, native-like environment. While nanodiscs have become powerful tools for studying membrane proteins, faithfully reconstituting the compositional asymmetry intrinsic to nearly all biological membranes has not yet been achieved. Proper membrane leaflet lipid distribution is critical for accurate protein folding, stability, and insertion. Here, we share a protocol for reconstituting tailored compositional asymmetry within nanodiscs through membrane extraction from giant unilamellar vesicles (GUVs) treated with a leaflet-specific methyl-β-cyclodextrin (mβCD) lipid exchange. Nanodisc asymmetry is verified through a geometric approach: biotin-DPPE-preloaded mβCD engages in lipid exchange with the outer leaflet of POPC GUVs solubilized by the lipid-free membrane scaffold protein (MSP) Δ49ApoA-I to form nanodisc structures. Once isolated, nanodiscs are introduced to the biotin-binding bacterial protein streptavidin. High-speed atomic force microscopy imaging depicts nanodisc–dimer complexes, indicating that biotin-DPPE was successfully reconstituted into a single leaflet of the nanodiscs. This finding outlines the first step toward engineering tailored nanodisc asymmetry and mimicking the native environment of integral proteins—a potentially powerful tool for accurately reconstituting and structurally analyzing integral membrane proteins whose functions are modulated by lipid asymmetry.

Biological and medical sciences↗

A Detailed Analysis of Visible Defects Formed in Commercial Silicon Thin-Film Modules During Outdoor Exposure

We analyzed defects in silicon thin-film tandem (a-Si:H/..mu..c-Si:H) modules from an outdoor installation in India. The inspection of several affected modules reveals that most of the defects -- which optically appear as bright spots -- were formed primarily nearby the separation and series connection laser lines. Cross-sectional SEM analysis reveals that the bright spots emerge due to electrical isolation, caused by a delamination of the cell from the front TCO in the affected area. In addition, the morphology of the a-Si:H top cell differs in the delaminated area compared to the surrounding unaffected area. We propose that these effects are potentially caused by an explosive and thermally triggered liberation of hydrogen from the a-Si:H layer. Electrical and thermal measurements reveal that these defects can impact the cell performance significantly.

14 SOLAR ENERGY↗

A Study of Fast Reactor Fuel Transmutation in a Candidate Dispersion Fuel Design

Dispersion fuels represent a significant departure from typical ceramic fuels to address swelling and radiation damage in high burnup fuel. Such fuels use a manufacturing process in which fuel particles are encapsulated within a non-fuel matrix. Dispersion fuels have been studied since 1997 as part of an international effort to develop and test very high density fuel types for the Reduced Enrichment for Research and Test Reactors (RERTR) program.[1] The Idaho National Laboratory is performing research in the development of an innovative dispersion fuel concept that will meet the challenges of transuranic (TRU) transmutation by providing an integral fission gas plenum within the fuel itself, to eliminate the swelling that accompanies the irradiation of TRU. In this process, a metal TRU vector produced in a separations process is atomized into solid microspheres. The dispersion fuel process overcoats the microspheres with a mixture of resin and hollow carbon microspheres to create a TRUC. The foam may then be heated and mixed with a metal power (e.g., Zr, Ti, or Si) and resin to form a matrix metal carbide, that may be compacted and extruded into fuel elements. In this paper, we perform reactor physics calculations for a core loaded with the conceptual fuel design. We will assume a “typical” TRU vector and a reference matrix density. We will employ a fuel and core design based on the Advanced Burner Test Reactor (ABTR) design.[2] Using the CSAS6 and TRITON modules of the SCALE system [3] for preliminary scoping studies, we will demonstrate the feasibility of reactor operations. This paper will describe the results of these analyses.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

TGF-beta1 release from biodegradable polymer microparticles: its effects on marrow stromal osteoblast function

BACKGROUND: Controlled release of transforming growth factor-beta1 (TGF-beta1) to a bone defect may be beneficial for the induction of a bone regeneration cascade. The objectives of this work were to assess the feasibility of using biodegradable polymer microparticles as carriers for controlled TGF-beta1 delivery and the effects of released TGF-beta1 on the proliferation and differentiation of marrow stromal cells in vitro. METHODS: Recombinant human TGF-beta1 was incorporated into microparticles of blends of poly(DL-lactic-co-glycolic acid) (PLGA) and poly(ethylene glycol) (PEG). Fluorescein isothiocynate-labeled bovine serum albumin (FITC-BSA) was co-encapsulated as a porogen. The effects of PEG content (0, 1, or 5% by weight [wt%]) and buffer pH (3, 5, or 7.4) on the protein release kinetics and the degradation of PLGA were determined in vitro for as long as 28 days. Rat marrow stromal cells were seeded on a biodegradable poly(propylene fumarate) (PPF) substrate. The dose response and biological activity of released TGF-beta1 was determined after 3 days in culture. The effects of TGF-beta1 released from PLGA/PEG microparticles on marrow stromal cell proliferation and osteoblastic differentiation were assessed during a 21-day period. RESULTS: TGF-beta1 was encapsulated along with FITC-BSA into PLGA/PEG blend microparticles and released in a multiphasic fashion including an initial burst for as long as 28 days in vitro. Increasing the initial PEG content resulted in a decreased cumulative mass of released proteins. Aggregation of FITC-BSA occurred at lower buffer pH, which led to decreased release rates of both proteins. The degradation of PLGA was increased at higher PEG content and significantly accelerated at acidic pH conditions. Rat marrow stromal cells cultured on PPF substrates showed a dose response to TGF-beta1 released from the microparticles similar to that of added TGF-beta1, indicating that the activity of TGF-beta1 was retained during microparticle fabrication and after growth factor release. At an optimal TGF-beta1 dosage of 1.0 ng/ml after 3 days, the released TGF-beta1 enhanced the proliferation and osteoblastic differentiation of marrow stromal cells over 21 days of culture, with increased total cell number, alkaline phosphatase activity, and osteocalcin production. CONCLUSIONS: PLGA/PEG blend microparticles can serve as delivery vehicles for controlled release of TGF-beta1, and the released growth factor enhances marrow stromal cell proliferation and osteoblastic differentiation in vitro. CLINICAL RELEVANCE: Controlled release of TGF-beta1 from PLGA/PEG microparticles is representative of emerging tissue engineering technologies that may modulate cellular responses to encourage bone regeneration at a skeletal defect site.

Non-NASA Center↗

Thin, High Lifetime Silicon Wafers with No Sawing; Re-crystallization in a Thin Film Capsule

The project fits within the area of renewable energy called photovoltaics (PV), or the generation of electricity directly from sunlight using semiconductor devices. PV has the greatest potential of any renewable energy technology. The vast majority of photovoltaic modules are made on crystalline silicon wafers and these wafers accounts for the largest fraction of the cost of a photovoltaic module. Thus, a method of making high quality, low cost wafers would be extremely beneficial to the PV industry. The industry standard technology creates wafers by casting an ingot and then sawing wafers from the ingot. Sawing rendered half of the highly refined silicon feedstock as un-reclaimable dust. Being a brittle material, the sawing is actually a type of grinding operation which is costly both in terms of capital equipment and in terms of consumables costs. The consumables costs associated with the wire sawing technology are particularly burdensome and include the cost of the wire itself (continuously fed, one time use), the abrasive particles, and, waste disposal. The goal of this project was to make wafers directly from molten silicon with no sawing required. The fundamental concept was to create a very low cost (but low quality) wafer of the desired shape and size and then to improve the quality of the wafer by a specialized thermal treatment (called re-crystallization). Others have attempted to create silicon sheet by recrystallization with varying degrees of success. Key among the difficulties encountered by others were: a) difficulty in maintaining the physical shape of the sheet during the recrystallization process and b) difficulty in maintaining the cleanliness of the sheet during recrystallization. Our method solved both of these challenges by encapsulating the preform wafer in a protective capsule prior to recrystallization (see below). The recrystallization method developed in this work was extremely effective at maintaining the shape and the cleanliness of the wafer. In addition, it was found to be suitable for growing very large crystals. The equipment used was simple and inexpensive to operate. Reasonable solar cells were fabricated on re-crystallized material.

14 SOLAR ENERGY↗

Development and Demonstration of an In-Situ Tritium Scavenger

The objective of this project was to use an inherent feature of salt-cooled reactors towards the capture and removal of tritium from the primary coolant system: the presence of the graphite moderator. The fuel elements fluoride-salt cooled high-temperature (FHR) reactors consist of a graphite matrix that encapsulates TRISO fuel particles, and the total fuel element surface area of Mark I PB-FHR is 7780 m 2 . Therefore the FHR fuel inherently provides removable graphite of high surface area. The goal of this project was to understand the transport of tritium across the salt-graphite interface. The following was achieved: 1. Electrochemical techniques were demonstrated for studying the entry, diffusion, and trapping of hydrogen isotopes in graphite. 2. Electrochemical techniques were used to demonstrate the relationship between galvanic corrosion between graphite and stainless steel 316 and hydrogen uptake in graphite. 3. Electrochemical techniques were demonstrated for studying the dissolution and diffusion of hydrogen isotopes in molten FLiBe. 4. Thermodynamic reference electrodes were tested for FLiBe and FLiNaK. 5. Electrochemical techniques were demonstrated as an in-salt hydrogen thermal desorption measurement, which had previously only been achieved in gas environments. 6. FLiBe exposure of graphite lead to graphite fluorination and an increase of defects, which indicate an increase of reactive carbon sites available for tritium uptake. 7. TRIDENT modeling was used to perform sensitivity analysis of FHR design parameters on tritium uptake fraction in graphite, showing high sensitivity to tritium diffusivity and solubility. 8. A cross-cutting effort with another NEUP-funded project was initiated for application of the SAM mass-transport module to system-scale tritium modeling.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Capabilities development for transient testing of advanced nuclear fuels at TREAT

The TREAT facility is a unique capability at the Idaho National Laboratory currently being prepared for resumption of nuclear transient testing. TREAT is an air-cooled reactor where the driver core is made up of urania dispersed in graphite blocks and encapsulated in zirconium alloy cans. In addition to the reactor itself, the foundation for TREAT's capabilities will also include a suite of irradiation vehicles and supporting infrastructure to provide the desired specimen boundary conditions while supporting a variety of instrumentation needs. Although TREAT historically supported all kinds of nuclear fuels, including LWR's, SFR's, space nuclear propulsion, research reactor plate-type fuels, and even fuels for use in the driver core of other transient test reactors, the majority of TREAT's more-recent experiment programs revolved around SFR's and sodium-environment test capsules and loops. MK-series loop experiment-specific test trains could be outfitted with a variety of instruments to monitor test and specimen conditions while the fast neutron hodoscope collected information about fuel movement before, during, and after transient excursions. The SERTTA (Static Environment Rodlet Transient Test Apparatuses) devices will be general purpose vehicles capable of providing inert gas, water (up to PWR conditions), steam, or perhaps even molten sodium environments within vessel-like capsules. The Multi-SERTTA vehicle design is particularly novel as it makes use of the full active core length in TREAT to test four small rodlets (∼12 cm length), each within its own hermetic boundary, it will be capable of housing pre-irradiated fuel specimens. Additional modules and adaptations of Multi-SERTTA will enable rapid loop pressure blowdown to simulate LOCA conditions. The Super-SERTTA, akin to the Multi-SERTTA will offer more possibilities for simulating transient phenomena.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NREL Validation of S3.2 and S3.3 (CRADA Final Report)

The scope of work for S3.2 and S3.3 validation includes cooperative planning, execution, and analysis of all recommended and agreed-upon test protocols to determine the suitability of the product for long-term deployment of the photovoltaic modules to a broad range of climates. The test plan will be established within two months of project initiation, and NREL will write monthly reports for the duration of the work.

14 SOLAR ENERGY↗