Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Current-voltage-time characteristics of the reactive Ar/N{sub 2} high power impulse magnetron sputtering discharge

The discharge current and voltage waveforms have been measured in a reactive high power impulse magnetron sputtering (HiPIMS) Ar/N{sub 2} discharge with a Ti target for 400 {mu}s long pulses. We observe that the current waveform in the reactive Ar/N{sub 2} HiPIMS discharge is highly dependent on the pulse repetition frequency, unlike the non-reactive Ar discharge. The current is found to increase significantly as the frequency is lowered. This is attributed to an increase in the secondary electron emission yield during the self-sputtering phase, when the nitride forms on the target at low frequencies. In addition, self-sputtering runaway occurs at lower discharge voltages when nitrogen is added to the discharge. This illustrates the crucial role of self-sputtering in the behavior of the reactive HiPIMS discharge.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Post-growth annealing induced change of conductivity in As-doped ZnO grown by radio frequency magnetron sputtering

Arsenic-doped ZnO films were fabricated by radio frequency magnetron sputtering method at a relatively low substrate temperature of 200 deg. C. Post-growth annealing in air was carried out up to a temperature of 1000 deg. C. The samples were characterized by Hall measurement, positron annihilation spectroscopy (PAS), secondary ion mass spectroscopy (SIMS), and cathodoluminescence (CL). The as-grown sample was of n-type and it converted to p-type material after the 400 deg. C annealing. The resulting hole concentration was found to increase with annealing temperature and reached a maximum of 6 x 10{sup 17} cm{sup -3} at the annealing temperature of 600 deg. C. The origin of the p-type conductivity was consistent with the As{sub Zn}(V{sub Zn}){sub 2} shallow acceptor model. Further increasing the annealing temperature would decrease the hole concentration of the samples finally converted the sample back to n-type. With evidence, it was suggested that the removal of the p-type conductivity was due to the dissociation of the As{sub Zn}(V{sub Zn}){sub 2} acceptor and the creation of the deep level defect giving rise to the green luminescence.

36 MATERIALS SCIENCE↗

Magnetron sputtering system for fabrication of X-ray multilayer optics

A specially designed DC/RF magnetron sputtering system has been installed for the development of large area x-ray multilayer (ML) optics at Indus synchrotron radiation facility. A brief description of the system configuration, automation and operating conditions are presented. The system has the capability of fabricating large area (300 Multiplication-Sign 100-mm{sup 2}) X-ray MLs with required accuracy, uniformity and reproducibility. Thin film growth suitable for fabrication of X-ray ML optics has achieved by optimizing the sputtering process parameters. The representative results are presented.

36 MATERIALS SCIENCE↗

Preparation and characterization of Gd{sub 2}O{sub 3} thin films by RF magnetron sputtering

Gd{sub 2}O{sub 3} films were deposited on to glass substrates held at room temperature using radio frequency (RF) magnetron sputtering, at a RF power of 63 W and argon pressure maintained at 1 Multiplication-Sign 10{sup -2}mbar. The morphology was studied by field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). The band gaps obtained from optical absorption studies are in the range of 3.4 and 4.02 eV, after annealing in air at 380 Degree-Sign C for 1 hour.

36 MATERIALS SCIENCE↗

Electrochemical properties of magnetron sputtered WO{sub 3} thin films

Thin films of tungsten oxide (WO{sub 3}) were deposited on ITO substrates by using RF magnetron sputtering at oxygen and argon atmospheres of 6 Multiplication-Sign 10{sup -2}Pa and 4 Pa respectively. The chemical composition and surface morphology of the WO{sub 3} thin films have been studied by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) respectively. The results indicate that the deposited WO{sub 3} thin films are nearly stoichiometric. The electrochemical performances of the WO{sub 3} thin films have been evaluated by galvonostatic charging/discharging method. The discharge capacity was 15{mu}Ah/cm{sup 2}{mu}m at the initial cycle and faded rapidly in the first few cycles and stabilized at a lesser stage.

36 MATERIALS SCIENCE↗

Influence of RF power on magnetron sputtered AZO films

Al-doped Zinc Oxide (AZO) transparent conducting films are prepared on glass substrate by RF magnetron sputtering under different RF power with a 3 inch diameter target of 2 wt%Al{sub 2}O{sub 3} in zinc oxide. The effect of RF power on the structural, optical and electrical properties of AZO films was investigated by X-ray Diffraction (XRD), Hall measurement and UV-Visible spectrophotometry. The XRD data indicates a preferential c-axis orientation for all the films. All films exhibit high transmittance (<90%) in visible region. Films deposited at 60 W power exhibit lowest resistivity of 5.7 Multiplication-Sign 10{sup -4}{omega}cm. Such low-resistivity and high-transmittance AZO films when prepared using low RF power at room temperature could find important applications in flexible electronics.

36 MATERIALS SCIENCE↗

Thermoelectric properties of epitaxial ScN films deposited by reactive magnetron sputtering onto MgO(001) substrates

Epitaxial ScN(001) thin films were grown on MgO(001) substrates by dc reactive magnetron sputtering. The deposition was performed in an Ar/N{sub 2} atmosphere at 2 Multiplication-Sign 10{sup -3} Torr at a substrate temperature of 850 Degree-Sign C in a high vacuum chamber with a base pressure of 10{sup -8} Torr. In spite of oxygen contamination of 1.6 {+-} 1 at. %, the electrical resistivity, electron mobility, and carrier concentration obtained from a typical film grown under these conditions by room temperature Hall measurements are 0.22 m{Omega} cm, 106 cm{sup 2} V{sup -1} s{sup -1}, and 2.5 Multiplication-Sign 10{sup 20} cm{sup -3}, respectively. These films exhibit remarkable thermoelectric power factors of 3.3-3.5 Multiplication-Sign 10{sup -3} W/mK{sup 2} in the temperature range of 600 K to 840 K. The cross-plane thermal conductivity is 8.3 W/mK at 800 K yielding an estimated ZT of 0.3. Theoretical modeling of the thermoelectric properties of ScN calculated using a mean-free-path of 23 nm at 300 K is in very good agreement with the experiment. These results also demonstrate that further optimization of the power factor of ScN is possible. First-principles density functional theory combined with the site occupancy disorder technique was used to investigate the effect of oxygen contamination on the electronic structure and thermoelectric properties of ScN. The computational results suggest that oxygen atoms in ScN mix uniformly on the N site forming a homogeneous solid solution alloy. Behaving as an n-type donor, oxygen causes a shift of the Fermi level in ScN into the conduction band without altering the band structure and the density of states.

36 MATERIALS SCIENCE↗

Carbon film deposition on SnO{sub 2}/Si(111) using DC unbalanced magnetron sputtering

In this paper, carbon deposition on SnO{sub 2} layer using DC unbalanced magnetron-sputtering technique at low temperature has been systematically studied. Sputtering process were carried out at pressure of 4.6×10{sup −2} Torr by keeping the substrate temperature at 300 °C. SnO{sub 2} were growth on silicon (111) substrate using thermal evaporation and continuing with dry oxidation of Sn at 225 °C. Thermal evaporation for high purity Sn was conducted by maintain the current source as high as 40 ampere. The quality of SnO{sub 2} on Si(111) and the characteristic of carbon thin film on SnO{sub 2} were analized by mean XRD, FTIR and Raman spectra. XRD analysis shows that SnO{sub 2} film is growth uniformly on Si(111). FTIR and Raman spectra confirm the formation of thin film carbon on SnO{sub 2}. Additionally, thermal annealing for some sample series have been performed to study their structural stability. The change of atomic structure due to thermal annealing were analized by Raman and XRD spectra.

36 MATERIALS SCIENCE↗

Preliminary study of CdTe and CdTe:Cu thin films nanostructures deposited by using DC magnetron sputtering

Growth and properties of CdTe and CdTe:Cu thin films nanostrucures deposited by using dc magnetron sputtering are reported. Scanning electron microscope (SEM) was used to observe the surface morphologies of the thin films. At growth conditions of 250 °C and 14 W, CdTe films did not yet evenly deposited. However, at growth temperature and plasma power of 325 °C and 43 W, both CdTe and CdTe:Cu(2%) have deposited on the substrates. In this condition, the morphology of the films indicate that the films have a grain-like nanostructures. Grain size diameter of about 200 nm begin to appear on top of the films. Energy Dispersive X-rays spectroscopy (EDX) was used to investigate chemical elements of the Cu doped CdTe film deposited. It was found that the film deposited consist of Cd, Te and Cu elements. XRD was used to investigate the full width at half maximum (FWHM) values of the thin films deposited. The results show that CdTe:Cu(2%) thin film has better crystallographic properties than CdTe thin film. The UV-Vis spectrometer was used to investigate the optical properties of thin films deposited. The transmittance spectra showed that transmittance of CdTe:Cu(2%) film is lower than CdTe film. It was found that the bandgap energy of CdTe and CdTe:Cu(2%) thin films of about 1.48 eV.

36 MATERIALS SCIENCE↗

Morphology and structure evolution of Cu(In,Ga)S{sub 2} films deposited by reactive magnetron co-sputtering with electron cyclotron resonance plasma assistance

Cu(In,Ga)S{sub 2} (CIGS) films were deposited on Mo coated soda lime glass substrates using an electron cyclotron resonance plasma enhanced one-step reactive magnetron co-sputtering process (ECR-RMS). The crystalline quality and the morphology of the Cu(In,Ga)S{sub 2} films were investigated by X-ray diffraction, atomic force microscopy, scanning electron microscopy, and X-ray fluorescence. We also compared these CIGS films with films previously prepared without ECR assistance and find that the crystallinity of the CIGS films is correlated with the roughness evolution during deposition. Atomic force microscopy was used to measure the surface topography and to derive one-dimensional power spectral densities (1DPSD). All 1DPSD spectra of CIGS films exhibit no characteristic peak which is typical for the scaling of a self-affine surface. The growth exponent β, characterizing the roughness R{sub q} evolution during the film growth as R{sub q} ∼ d{sup β}, changes with film thickness. The root-mean-square roughness at low temperatures increases only slightly with a growth exponent β = 0.013 in the initial growth stage, while R{sub q} increases with a much higher exponent β = 0.584 when the film thickness is larger than about 270 nm. Additionally, we found that the H{sub 2}S content of the sputtering atmosphere and the Cu- to-(In + Ga) ratio has a strong influence of the morphology of the CIGS films in this one-step ECR-RMS process.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Initial stages of ITO/Si interface formation: In situ x-ray photoelectron spectroscopy measurements upon magnetron sputtering and atomistic modelling using density functional theory

Initial stages of indium tin oxide (ITO) growth on a polished Si substrate upon magnetron sputtering were studied experimentally using in-situ x-ray photoelectron spectroscopy measurements. The presence of pure indium and tin, as well as Si bonded to oxygen at the ITO/Si interface were observed. The experimental observations were compared with several atomistic models of ITO/Si interfaces. A periodic model of the ITO/Si interface was constructed, giving detailed information about the local environment at the interface. Molecular dynamics based on density functional theory was performed, showing how metal-oxygen bonds are broken on behalf of silicon-oxygen bonds. These theoretical results support and provide an explanation for the present as well as previous ex-situ and in-situ experimental observations pointing to the creation of metallic In and Sn along with the growth of SiO{sub x} at the ITO/Si interface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Heteroepitaxial growth of Cu{sub 2}ZnSnS{sub 4} thin film on sapphire substrate by radio frequency magnetron sputtering

The heteroepitaxy of tetragonal Cu2ZnSnS4 (CZTS) thin films on hexagonal sapphire (0001) single crystal substrates is successfully obtained by radio frequency magnetron sputtering. The sputtered CZTS film has a mirror-like smooth surface with a root mean square roughness of about 5.44 nm. X-ray θ-2θ scans confirm that CZTS film is (112) oriented on sapphire with an out of plane arrangement of CZTS (112) ‖ sapphire (0001). X-ray Phi scan further illustrates an in plane ordering of CZTS [201{sup ¯}] ‖ sapphire [21{sup ¯}1{sup ¯}0]. The high resolution transmission electron microscopy image of the interface region clearly shows that the CZTS thin film epitaxially grows on the sapphire (0001) substrate. The band gap of the film is found to be approximately 1.51 eV.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Investigation of ionized metal flux in enhanced high power impulse magnetron sputtering discharges

The metal ionized flux fraction and production of double charged metal ions Me{sup 2+} of different materials (Al, Cu, Fe, Ti) by High Power Impulse Magnetron Sputtering (HiPIMS) operated with and without a pre-ionization assistance is compared in the paper. The Electron Cyclotron Wave Resonance (ECWR) discharge was employed as the pre-ionization agent providing a seed of charge in the idle time of HiPIMS pulses. A modified grid-free biased quartz crystal microbalance was used to estimate the metal ionized flux fraction ξ. The energy-resolved mass spectrometry served as a complementary method to distinguish particular ion contributions to the total ionized flux onto the substrate. The ratio between densities of doubly Me{sup 2+} and singly Me{sup +} charged metal ions was determined. It is shown that ECWR assistance enhances Me{sup 2+} production with respect of absorbed rf-power. The ECWR discharge also increases the metal ionized flux fraction of about 30% especially in the region of lower pressures. Further, the suppression of the gas rarefaction effect due to enhanced secondary electron emission of Me{sup 2+} was observed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Morphology and structure evolution of tin-doped indium oxide thin films deposited by radio-frequency magnetron sputtering: The role of the sputtering atmosphere

The microstructure and morphology evolution of tin-doped indium oxide (ITO) thin films deposited by radio-frequency magnetron sputtering in different sputtering atmospheres were investigated by X-ray diffraction, X-ray reflectivity, and atomic force microscopy. The surface roughness w increases with increasing film thickness d{sub f}, and exhibits a power law behavior w ∼ d{sub f}{sup β}. The roughness decreases with increasing O{sub 2} flow, while it increases with increasing H{sub 2} flow. The growth exponent β is found to be 0.35, 0.75, and 0.98 for depositions in Ar/10%O{sub 2}, pure Ar, and Ar/10%H{sub 2} atmospheres, respectively. The correlation length ξ increases with film thickness also with a power law according to ξ ∼ d{sub f}{sup z} with exponents z = 0.36, 0.44, and 0.57 for these three different gas atmospheres, respectively. A combination of local and non-local growth modes in 2 + 1 dimensions is discussed for the ITO growth in this work.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The impact of argon admixture on the c-axis oriented growth of direct current magnetron sputtered Sc{sub x}Al{sub 1−x}N thin films

The piezoelectric properties of wurtzite aluminium nitride (w-AlN) are enhanced by alloying with scandium (Sc), thus offering superior properties for applications in micro electro-mechanical systems devices. Sc{sub x}Al{sub 1−x}N thin films have been prepared by DC reactive magnetron sputtering on Si (100) substrates from a single target. When targeting a concentration range from x = 0 up to x = 0.15, the preparation conditions have been optimized by varying the Ar/N{sub 2} ratio in the sputtering gas. To incorporate an increasing Sc concentration, a higher Ar/N{sub 2} ratio has to be applied during the deposition process. Hence, the argon concentration in the sputtering gas becomes a crucial parameter for microstructure-related parameters. To determine phase purity, degree of c-axis orientation, lattice parameter, and grain size, the Sc{sub x}Al{sub 1−x}N thin films were investigated by techniques, such as scanning electron microscopy, transmission electron microscopy, and X-ray diffraction.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Strain mediated coupling in magnetron sputtered multiferroic PZT/Ni-Mn-In/Si thin film heterostructure

The strain mediated electrical and magnetic properties were investigated in PZT/Ni-Mn-In heterostructure deposited on Si (100) by dc/rf magnetron sputtering. X-ray diffraction pattern revealed that (220) orientation of Ni-Mn-In facilitate the (110) oriented tertragonal phase growth of PZT layer in PZT/Ni-Mn-In heterostructure. A distinctive peak in dielectric constant versus temperature plots around martensitic phase transformation temperature of Ni-Mn-In showed a strain mediated coupling between Ni-Mn-In and PZT layers. The ferroelectric measurement taken at different temperatures exhibits a well saturated and temperature dependent P-E loops with a highest value of P{sub sat}~55 μC/cm² obtained during martensite-austenite transition temperature region of Ni-Mn-In. The stress induced by Ni-Mn-In layer on upper PZT film due to structural transformation from martensite to austenite resulted in temperature modulated Tunability of PZT/Ni-Mn-In heterostructure. A tunability of 42% was achieved at 290 K (structural transition region of Ni-Mn-In) in these heterostructures. I-V measurements taken at different temperatures indicated that ohmic conduction was the main conduction mechanism over a large electric field range in these heterostructures. Magnetic measurement revealed that heterostructure was ferromagnetic at room temperature with a saturation magnetization of ~123 emu/cm³. Such multiferroic heterostructures exhibits promising applications in various microelectromechanical systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Studies on optoelectronic properties of DC reactive magnetron sputtered chromium doped CdO thin films

Cr doped CdO thin films were deposited on glass substrates by DC reactive magnetron sputtering method and subsequently annealed from 200 °C to 500 °C. X-ray diffraction analysis showed that the films exhibit (1 1 1) preferred orientation. The optical transmittance of the films increases from 64% to 88% with increasing annealing temperature. The optical band gap values were found to be decreased from 2.77 to 2.65 eV with the increase of annealing temperature. The decrease in optical band gap energy with increasing annealing temperature can be attributed to improvement in the crystallinity of the films and may also be due to quantum confinement effect. A minimum resistivity of 2.23 × 10{sup −4} Ω.cm and sheet resistance of 6.3 Ω/sq is obtained for Cr doped CdO film annealed at 500 °C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural and optical properties of DC reactive magnetron sputtered zinc aluminum oxide thin films

Highly transparent conductive Zinc Aluminum Oxide (ZAO) thin films have been deposited on glass substrates using DC reactive magnetron sputtering method. The thin films were deposited at 200 °C and post-deposition annealing from 15 to 90 min. XRD patterns of ZAO films exhibit only (0 0 2) diffraction peak, indicating that they have c-axis preferred orientation perpendicular to the substrate. Scanning electron microscopy (SEM) is used to study the surface morphology of the films. The grain size obtained from SEM images of ZAO thin films are found to be in the range of 20 - 26 nm. The minimum resistivity of 1.74 × 10{sup −4} Ω cm and an average transmittance of 92% are obtained for the thin film post annealed for 30 min. The optical band gap of ZAO thin films increased from 3.49 to 3.60 eV with the increase of annealing time due to Burstein-Moss effect. The optical constants refractive index (n) and extinction coefficient (k) were also determined from the optical transmission spectra.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗