Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNESIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Deformation Behavior of a Coarse-Grained Mg-8Al-1.5Ca-0.2Sr Magnesium Alloy at Elevated Temperatures

The compression tests were carried out on a coarse-grained Mg-8Al-1.5Ca-0.2Sr magnesium alloy samples at temperatures from 300 to 450 °C and strain rates from 0.001 to 10 s{sup −1}. The flow stress curves were analyzed using the double-differentiation method, and double minima were detected on the flow curves. The first set of minima is shown to identify the critical strain for twinning, while the second set indicates the critical strain for the initiation of dynamic recrystallization (DRX). Twin variant selection was numerically identified by comprehensive analysis of the Schmid factors for different deformation modes and the accommodation strains imposed on neighboring grains. It was found that twinning is initiated before DRX. Dynamic recrystallization volume increases with strain rate at a given deformation temperature. At high strain rate, various twin variants are activated to accommodate deformation, leading to the formation of twin intersections and high DRX volume. Fully dynamic recrystallized structure can be obtained at both high and low strain rates due to the high mobility of the grain and twin boundaries at the temperature of 400 °C.

36 MATERIALS SCIENCE↗

Improving Joint Formation and Tensile Properties of Dissimilar Friction Stir Welding of Aluminum and Magnesium Alloys by Solving the Pin Adhesion Problem

Friction stir welding (FSW), as a solid-state welding technology invented by TWI in 1991, has potential to join dissimilar Al/Mg alloys. In this study, the pin adhesion phenomenon affecting joint quality during FSW of 6061-T6 aluminum and AZ31B magnesium alloys was investigated. The adhesion phenomenon induced by higher heat input easily transformed the tapered-and-screwed pin into a tapered pin, which greatly reduced the tool’s ability to drive the plasticized materials and further deteriorated joint formation. Under the condition without the pin adhesion, the complex intercalated interlayer at the bottom of stir zone was beneficial to mechanical interlocking of Al/Mg alloys, improving tensile properties. However, the formation of intermetallic compounds was still the main reason of the joint fracture, significantly deteriorating tensile properties. Under the welding speed of 60 mm/min without the pin adhesion phenomenon, the maximum tensile strength of 107 MPa and elongation of 1.2% were achieved.

36 MATERIALS SCIENCE↗

Workability Limits of Magnesium Alloy AZ31B Subjected to Equal Channel Angular Pressing

Equal channel angular pressing (ECAP) is an important severe plastic deformation process to produce ultrafine grained microstructures in metals and alloys. Magnesium and its alloys generally possess poor workability at temperatures below 250 °C. This investigation examines the influence of different passes and processing routes of ECAP on improving the workability of Mg alloy AZ31B. ECAP was carried out for three passes using a die of angle 120° using processing routes Bc and C. The operating temperature was 523 K for the first pass and 423 K for the subsequent two passes. The resultant microstructure and mechanical properties were determined. Workability of the alloy at 423 K (150 °C) was determined using upsetting experiments on cylindrical specimens machined from the annealed and ECAPed samples. Workability limit diagrams have been constructed for the various processed conditions. The workability data generated were also analyzed using five different workability criteria (also referred to as ductile fracture models) and the material constants for these five models were evaluated. Specimens processed by two passes through route C (pass 2C) exhibits better workability compared to other passes since the workability limit line after this pass shows maximum safe working area and lies above the other workability lines. Among the five different workability criteria investigated, the Freudenthal workability criterion is more suitable for prediction of failure in this alloy.

36 MATERIALS SCIENCE↗

Alleviation of Mechanical Anisotropy in Ultrafine/Nano-grained AZ31 Magnesium Alloy

An ultrafine/nano-grained AZ31 magnesium alloy was processed through multipass accumulative back extrusion at 280 and 380 °C. Texture analysis was conducted to determine preferred crystallographic orientations developed during multipass deformation. The anisotropy in mechanical properties of the processed materials was studied by compressive and tensile testing. The results implied that the accumulative back extrusion effectively reduces the anisotropy of yield strength, ultimate strength and strain-to-fracture during compressive and tensile loading. The operations of different twinning/slip systems during compressive and tensile deformation were discussed using Schmid factors measurements. A decrease in twinning-related anisotropy, as well as the contribution of different slip systems in strain accommodation, could reduce the mechanical anisotropy of ultrafine/nano-grained AZ31 alloy. The compressive strength of the two-pass processed material was lower along extrusion direction than transverse direction; however, the result was reverse after four passes. The tensile behavior implied that the contribution of basal slip might accommodate strain along length as well as the thickness of the specimen, while prismatic slip may assist in narrowing the width of the specimen and elongating the length.

36 MATERIALS SCIENCE↗

Deformation Behavior of AM30 Magnesium Alloy

In this study, deformation behavior of AM30 magnesium alloy is investigated in the hot working regime and empirical relations are developed. Compression tests were performed in the 0.001-10 s{sup −1} strain rate range and 423-623 K temperature range to obtain the mechanical properties. The compression curves were fitted using two approaches, viz. piecewise linear fitting and a Johnson–Cook type relation. Piecewise linear fit is found to be appropriate for describing the mechanical behavior in the dynamic recrystallization (DRX) regime as compared to the proposed Johnson–Cook type relation. The Johnson–Cook type model is not able to capture the essential feature of DRX, particularly at high strain rates.

36 MATERIALS SCIENCE↗

Microstructure Analysis and Rheological Behavior of Magnesium Alloys at Semi-solid Temperature Range

Microstructure and rheological properties of AZ91 and Elektron 21 magnesium alloys in semi-solid state were studied. Differential scanning calorimetry revealed significant differences in melting range in analyzed materials. Isothermal annealing for 5, 30 and 80 min, in semi-solid range, corresponding to 50 and 70% of solid fraction, showed slower microstructure coarsening kinetics in Elektron 21 due to the presence of Zr- and RE-enriched precipitations. Ostwald ripening and coalescence resulted in decrease in grains density with increasing annealing time and temperature. Hardness after annealing showed overall tendency to diminish with soaking time probably due to the growth of average grain size. Rheological analysis showed tendency to lower the value of dynamic viscosity coefficient as shear rate rise, which confirmed non-Newtonian flow behavior. The highest values of dynamic viscosity coefficient were obtained for alloy AZ91.

36 MATERIALS SCIENCE↗

Effect of Precompression Deformation on the Strain-Controlled Low-Cycle Fatigue Behavior of Extruded AZ31 Magnesium Alloy

In this work, the effect of precompression along the extrusion direction on the strain-controlled low-cycle fatigue behavior of an extruded AZ31 magnesium alloy was investigated. After precompression deformation occurred, the tensile yield strength decreased, whereas the tensile yield strength and ultimate tensile strength increased gradually as precompression deformation increased. The shape of the stress–strain hysteresis of a specimen with 5% precompression deformation changed from asymmetrical to symmetrical compared with that of the as-extruded specimen. Hence, the whole process was likely dominated by twinning–detwinning behavior. Fractographic analysis revealed that the crack propagation region of the specimen with 5% precompression deformation was flatter than that of the as-extruded specimen because of the compressive mean stress and finer grains in the specimen with 5% precompression deformation. The fatigue lives of the as-extruded and precompression specimens were predicted by the Coffin–Manson model, the Ellyin energy model, the Smith–Watson–Topper model, the Fatemi–Socie model, and the Jiang model, respectively. The life predicted by the Ellyin energy model and the Jiang model was consistent with the experimental data.

36 MATERIALS SCIENCE↗

Microstructure, Texture, and Mechanical Properties of AM60 Magnesium Alloy Processed by Extrusion and Multidirectional Forging

In the present paper, multidirectional forging (MDF), as a severe plastic deformation process, was carried out on an extruded AM60 magnesium alloy. The microstructure, texture, and mechanical properties of the MDFed samples were examined. Microstructural findings indicated that the grain size of the alloy decreased from 10.2 to 3.7 µm after six MDF passes, carried out at a constant temperature of 220 °C. Textural studies revealed that after six MDF passes, the fiber texture of the extruded material was transformed to another texture, in which the basal planes tend to rotate toward 45{sup o} to the transverse direction. Shear punch testing (SPT) was employed to assess the shear yield stress (SYS) and ultimate shear strength (USS) at room temperature. Both SYS and USS were enhanced after two MDF passes, but decreased in the next pressing stages, despite developing finer grains at higher levels of imposed strain. The observed drop in strength is ascribed to texture softening that counterbalances the grain refinement strengthening effects. The variation in average microhardness values after different passes of MDF showed the trend that was in concurrence with the rise and fall of the SPT results. Finally, the changes in mechanical properties were discussed, based on the microstructural and textural findings.

36 MATERIALS SCIENCE↗

Room-Temperature Microstructural Evolution of Extruded AM80 Magnesium Alloys under Dynamic Loading

Dynamic compression tests were conducted using a split Hopkinson pressure bar along the transverse direction at strain rates (SRs) of 3200 and 6000 s{sup −1}. The initial microstructure significantly affected the flow stress behavior and microstructural evolution of the two studied AM80 magnesium alloys. Under the same SR loading, the as-extruded alloy exhibited an apparently higher flow stress. At a SR of 6000 s{sup −1}, the flow stress of the as-extruded alloy exhibited a visible decrease (~ 34 MPa) as the strain increased to ~ 0.2, whereas a constant flow stress was exhibited by the solution-treated alloy. High-density dislocations and mechanical twins were detected in the two alloys at a SR of 3200 s{sup −1}. Interestingly, dynamic recrystallization (DRX) with an average grain size of ~ 2 µm was only identified in the as-extruded alloy as the applied SR increased to 6000 s{sup −1}. The increased localized deformation in the as-extruded alloy due to the retained strain energy and high critical twinning stress improved the DRX driving force, thereby resulting in visibly different micrographs of the two alloys when impacted at the SR of 6000 s{sup −1}.

36 MATERIALS SCIENCE↗

Microstructure Evolution of Ultra-Fine-Grained AZ31 B Magnesium Alloy Produced by Submerged Friction Stir Processing

Ten-millimeter-thick strain-hardened AZ31B-H24 magnesium sheets were subjected to friction stir processing (FSP) in air and submerged friction stir processing (SFSP) under water to investigate their microstructures and microhardness properties. Different rotational speeds of 500, 630, 800, and 1000 rpm and traverse speeds of 50, 100, 200, and 350 mm/min were employed for processing the materials. For SFSPed samples, the rotational speed of 500 rpm and 200 mm/min of traverse speed resulted in an ultra-fine-grained structure with a minimum grain size of about 400-500 nm, which is half compared to that of FSPed. It was found that both processes led to variation of crystallographic orientation, and enhancing the rotational speed and lowering the traverse speed promoted the development of a {0002} basal texture. The microhardness of SFSPed material increased significantly up to 110% (~ 95 Hv), while the microhardness was 45% (~ 65 Hv) higher than the base metal (~ 45 Hv) for FSPed material.

36 MATERIALS SCIENCE↗

Solderability of AZ31B Magnesium Alloy Coated by Copper and Strength of the Solder Joints

Magnesium alloys are promising as light materials, while their high chemical reactivity makes them difficult to be soldered. In this study, the AZ31B alloy was pretreated by zincification and coated by an electrodeposited Cu layer, and then soldered with Sn-58Bi solder in air furnace. The microstructure and properties of the AZ31B/Cu(Zn)/SnBi solder joints were characterized to evaluate the solderability of the Cu-coated Mg alloy and the influence of soldering on the Cu coating. It was found that the Cu coating is dense, and little defect exists along the Cu(Zn)/AZ31B interface. The soldering process has little negative effect on the bonding between the Cu coating and the AZ31B substrate, and the AZ31B/Cu(Zn)/SnBi solder joints of high metallurgical quality were obtained. Tensile fracture of the solder joint occurs mainly in the solder, with no peeling of the Cu coating. Under shear loading, cracks initiate inside the SnBi solder and the final fracture of the joint occurs around the Cu{sub 6}Sn{sub 5}/solder interface or along the Cu(Zn)/AZ31B interface. The tensile and shear strength of the AZ31B/Cu(Zn)/SnBi solder joints are close to that of the SnBi/Cu solder joints. It is demonstrated that the Cu-coated Mg alloy shows superior solderability and can be soldered by the Sn-based low-melting solder in air.

36 MATERIALS SCIENCE↗

The Effect of Annealing on the Properties of AW5754 Aluminum Alloy-AZ31B Magnesium Alloy Explosively Welded Bimetals

Explosive welding of AW5754 aluminum alloy to AZ31B magnesium alloy was performed. AW5754 was proposed as a flyer plate. A parallel setup was used during explosive welding. The annealing of AW5754/AZ31B composite plate at 250, 300 and 350 °C for 2, 3, 4 and 5 h was performed after explosive welding. Bimetals were characterized by regular wavy interface. Annealing resulted in the creation of intermetallic compounds (IMCs). The increase in the thickness of IMC interfacial layer was observed with increasing of annealing temperature and time. IMC layer of highest thickness was recorded after annealing at 350 °C for 5 h and averaged 67 µm. EDS analysis showed that the interfacial layer close to AW5754 alloy was formed by Al{sub 3}Mg{sub 2} IMC, and interfacial layer adjacent to the AZ31B alloy consisted of Mg{sub 17}Al{sub 12} IMC. Bright particles were spread at the AW5754-Al{sub 3}Mg{sub 2} IMC interface. Rise in the microhardness at the interface of produced bimetal was associated with work hardening. Microhardness values increased to 218 HV0.025 after annealing process due to IMCs present at the interface. Decrease in microhardness in locations close to the IMC interfacial layer was found after heat treatment due to recrystallization. The bimetal tensile strength reached 120 MPa. The annealing resulted in decrease in the bimetal tensile strength.

36 MATERIALS SCIENCE↗

Protective Performance of Plasma-Enhanced Chemical Vapor-Deposited Ethyl Cyclohexane Coating on Magnesium Alloys

In the present investigation, plasma-polymerized ethyl cyclohexane (ECH) coatings were deposited onto AZ31 and AM50 magnesium (Mg) alloys using plasma-enhanced chemical vapor deposition. The influences of deposition time on the coating formation, surface morphology, chemical composition and electrochemical corrosion behavior were investigated. The coating deposition was confirmed by infrared spectroscopy (FT-IR), and the thickness was measured using a scanning electron microscope. Energy-dispersive x-ray analysis revealed an increase in carbon and a decrease in Mg concentrations as the coating duration was increased. Electrochemical impedance spectroscopy (EIS) results confirmed an improvement in the corrosion resistance of AZ31 and AM50 alloys due to ECH coatings in the presence of a 3.5 wt.% NaCl solution. Further, equivalent circuit curve fitting analysis of the EIS results indicated an increase in charge transfer resistance (R{sub ct}) values with longer coating durations. These results confirmed the protecting ability of ECH coatings against corrosive ion attack, which was also substantiated by the surface morphologies after corrosion. Impedance values decreased as the duration of exposure in a NaCl solution increased, and the coating prepared using a 30-min ECH deposition exhibited better protection properties.

36 MATERIALS SCIENCE↗

Transmission Electron Microscope In Situ Straining Technique to Directly Observe Defects and Interfaces During Deformation in Magnesium

In-situ straining was used to study deformation behavior of hexagonal close-packed (hcp) metals.Twinning and dislocation motion, both essential to plasticity in hcp materials, were observed.Typically, these processes are characterized post-mortem by examining remnant microstructural features after straining has occurred. By imposing deformation during imaging, direct observation of active deformation mechanisms is possible. This work focuses on straining of structural metals in a transmission electron microscope (TEM), and a recently developed technique that utilizes familiar procedures and equipment to increase ease of experiments. In-situ straining in a TEM presents several advantages over conventional post-mortem characterization, most notably time-resolution of deformation and streamlined identification of active deformation mechanisms. Drawbacks to the technique and applicability to other studies are also addressed. In-situ straining is used to study twin boundary motion in hcp magnesium. A {101¯2} twin was observed during tensile and compressive loading. Twin-dislocation interactions are directly observed. Notably, dislocations are observed to remain mobile, even after multiple interactions with twin boundaries, a result which suggests that Basinki’s dislocation transformation mechanism by twinning is not present in hcp metals. The coupling of in-situ straining with traditional post-mortem characterization yields more detailed information about material behavior during deformation than either technique alone.

magnesium↗

Anisotropic deformation of extruded magnesium alloy AZ31 under uniaxial compression: A study with simultaneous in situ synchrotron x-ray imaging and diffraction

In situ synchrotron x-ray imaging and diffraction are used to investigate anisotropic deformation of an extruded magnesium alloy AZ31 under uniaxial compression along two different directions, with the loading axis (LA) either parallel or perpendicular to the extrusion direction (ED), referred to as LA∥ED and LAED, respectively. Multiscale measurements including stress–strain curves (macroscale), x-ray digital image correlation (mesoscale), and diffraction (microscale) are obtained simultaneously. Electron backscatter diffraction is performed on samples collected at various strains to characterize deformation twins. The rapid increase in strain hardening rate for the LA∥ED loading is attributed to marked {101¯2} extension twinning and subsequent homogenization of deformation, while dislocation motion leads to inhomogeneous deformation and a decrease in strain hardening rate.

36 MATERIALS SCIENCE↗

Dependence of twinned volume fraction on loading mode and Schmid factor in randomly textured magnesium

Here, the twinning activity in random textured cast magnesium during room temperature tension and compression tests was monitored by neutron diffraction (ND). Variation of integrated intensities of selected diffraction peaks, characterizing the twinned volume in particularly oriented grains was compared with calculated Schmid factors for extension twinning of these grains. It is shown that in tension there is a direct proportion between the twinned volume and the maximum value of the Schmid factor for a given grain orientation. In contrast, in compression this relation is not valid. The twinned volume in this case is influenced by both deviation of the grain from the ideal orientation and its rotation around the c-axis. The experimental results are in good agreement with those obtained from elasto-plastic self-consistent (EPSC) modeling.

36 MATERIALS SCIENCE↗

The study of the core–valence and core–core correlation effects on the radiative properties along the magnesium isoelectronic sequence

We investigated the effect of core–valence and core–core correlations on the energy levels and transition probabilities along the Mg isoelectronic sequence from Si{sup 2+} to U{sup 80+}. In order to attain a certain accuracy for the atomic structure we considered configurations obtained by electron promotions from the n=3 up to n=7 valence shells. Core–valence and core–core correlations are systematically included in the model by allowing single and double electron promotions from the n=2 core up to the n=6 and n=5 shells with l≤4 and l≤2, respectively. The present results contain the energy of the levels arising from the valence configurations along with oscillator strengths and radiative rates corresponding to E1, M1, E2, M2 transitions between states arising from 3l3l{sup ′} with l,l{sup ′}≤2 and 3snl{sup ′′} with n≤7 and l{sup ′′}≤4 configurations. We conclude the data accuracy trend along the magnesium isoelectronic sequence as a result of the detailed study of the correlation effects on the radiative properties. The core–valence correlations generally improve both energy and radiative rate values, while the core–core correlations mostly give better oscillator strengths but may slightly increase the energy deviations. The calculations have been performed by employing the fully relativistic model-potential Flexible Atomic Code.

74 ATOMIC AND MOLECULAR PHYSICS↗

Distinctive features of fluorescence and waveguides in magnesium aluminate spinel crystals driven by structural discrepancy

Transparent polycrystalline ceramics are of significant importance for a wide range of scientific and industrial applications. Developing a deeper understanding of their thermodynamic behavior is essential for achieving their maximum output performance in technological applications. This study provides a systematic investigation into the thermal excitation-induced fluorescence kinetics and waveguide characteristics of Magnesium Aluminate Spinel (MgAl 2 O 4 ) single crystals, with a focus on the intricate relationship between structure and properties. High-temperature extreme environments through irradiation with swift heavy ions 645.0 MeV Xe and 352.8 MeV Fe ions were created; the atomic deposition energy threshold (E th ) associated with disorder morphologies was assessed between 0.91 and 0.99 eV atom –1 . The track prediction model was developed to support the theoretical prediction of track formation. Electronic energy loss (E ele ) disrupts the balance of the initial structure through the thermal spike effect, leading to the formation of absorption-related F and F + color centers. These defects enhance photoluminescence in the visible spectrum and result in an effective modulation of the intrinsic bandgap. Moreover, as ion beams penetrate into the material, the uneven damage distribution induces the formation of waveguide structures. In conclusion, these findings provide valuable insights into the fabrication of functional devices through irradiation technologies and the structural changes of MgAl 2 O 4 at high temperatures within extreme environments.

36 MATERIALS SCIENCE↗