Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Locating Profile”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Data base for the Colorado profiling network

The Colorado profiling system developed by the Wave Propagation Laboratory (WPL) includes five (soon to be six) Doppler radar wind Profilers; four operate at 49 MHz (6 m) and are located at Platteville, Fleming, Lay Creek, and Cahone, and one operates at 915 MHz (33 cm) and is located at Denver. The sixth radar, now under construction, will operate at 405 MHz (UHF) and will be located at Boulder. Microwave radiometers and surface meteorological stations are at some of the radar sites. The data base for the wind Profilers is discussed.

Merritt, D. A.↗

Active region mass motions observed in soft X-ray lines

Significant coronal mass motions are deduced from soft X-ray line broadening observed in solar active regions even during quiescent periods. A large data base of Mg XI resonance line profiles near 9.17 A has been acquired with the SMM Flat Crystal Spectrometer for a variety of active region conditions and disk locations. For the X-ray bright areas, the typical profiles have an excess line width equal to or greater than the thermal Doppler width for Mg ions at the observed coronal temperatures (3-4 MK). The equivalent excess velocities of 40-60 km/s are higher than those reported previously for cooler lines in other wavebands. The excess velocities show a correlation with magnetic field strength or gradient, but no obvious dependence on the angular distance from sun center.

Saba, J. L. R.↗

Stratospheric Ozone Climatology from Lidar Measurements at Table Mountain (34.0 deg N, 117.7 deg W) and Mauna Loa (19.5 deg N, 155.6 deg W)

Using more than 1600 nighttime profiles obtained by the JPL differential absorption lidars (DIAL) located at Table Mountain Facility (TMF, 34.4 N) and Mauna Loa Observatory (MLO, 19.5 N) is presented in this paper. These two systems have been providing high-resolution vertical profiles of ozone number density between 15-50 km, several nights a week since 1989 (TMF) and 1993 (MLO). The climatology presented here is typical of early night ozone values with only a small influence of the Pinatubo aerosols and the 11-year solar cycle. The observed seasonal and vertical structure of the ozone concentration at TMF is consistent with that typical of mid- to subtropical latitudes. A clear annual cycle in opposite phase below and above the ozone concentration peak is observed. The observed winter maximum below the ozone peak is associated with a maximum day-to-day variability, typical of a dynamically driven lower stratosphere. The maximum concentration observed in summer above the ozone peak emphasizes the more dominant role of photochemistry. Unlike TMF, the ozone concentration observed at MLO tends to be higher during the summer months and lower during the winter months throughout the entire stratospheric ozone layer. Only a weak signature of the extra-tropical latitudes is observed near 19-20 km, with a secondary maximum in late winter. The only large variability observed at MLO is associated with the natural variability of the tropical tropopause.

Leblanc, T.↗

Slip band characteristics in the presence of grain boundaries in nickel-based superalloy

Shear strain profiles along slip bands in a modified Rolls-Royce nickel superalloy (RR1000) were analyzed for a tensile sample deformed by 2%. The strain increased with distance away from a grain boundary (GB), with maximum shear strain towards the center of the grain, indicating that dislocation nucleation generally occurred in the grain interior. The strain gradients in the neighborhood of the GBs were quantified and generally correlated with rotation about the active slip system line direction. This leads to an ability to determine the active slip system in these regions. The dislocation spacing and pileup stresses were inferred. The dislocation spacing closely follows an Eshelby analytical solution for a single ended pileup of dislocations under an applied stress. The distribution of pileup stress values for GBs of a given misorientation angle follows a log-normal distribution, with no correlation between the pileup stress and the GB misorientation angle. Furthermore, there is no observed correlation between various transmissivity factors and slip band pileup stress. Hence it appears that the obstacle strength of any of the observed GBs is adequate to facilitate the dislocation pileups present in the slip bands. However, slip band transmission does correlate with transmissivity factors, with the current study focusing on the Luster and Morris m’-factor. Observation of strain profiles of transmitted bands indicate dislocation nucleation locations.

36 MATERIALS SCIENCE↗

Using dispersivity values to quantify the effects of pore-scale flow focusing on enhanced reaction along a transverse mixing zone

A key challenge for predictive modeling of transverse mixing and reaction of solutes in groundwater is to determine values of transverse dispersivity (α T ) in heterogeneous flow fields that accurately describe mixing and reaction at the pore scale. We evaluated the effects of flow focusing in high permeability zones on mixing enhancement using experimental micromodel flow cells and pore-scale lattice-Boltzmann-finite-volume model (LB-FVM) simulations. Micromodel results were directly compared to LB-FVM simulations using two different pore structures, and excellent agreement was obtained. Six different flow focusing pore structures were then systematically tested using LB-FVM, and both analytical solutions and a two-dimensional (2D) continuum-scale model were used to fit α T values to pore-scale results. Pore-scale results indicate that the overall rate of mixing-limited reaction increased by up to 40% when flow focusing occurred, and it was greater in pore structures with longer flow focusing regions and greater porosity contrast. For each pore structure, α T values from analytical solutions of transverse concentration profiles or total product at a given longitudinal location showed good agreement for nonreactive and reactive solutes, and values determined in flow focusing zones were always smaller than those downgradient after the flow focusing zone. Transverse dispersivity values from the 2D continuum model were between values within and downgradient from the flow focusing zone determined from analytical solutions. Also, total product and transverse concentration profiles along the entire pore structure from the 2D continuum model matched pore scale results. Finally, these results indicate that accurate quantification of pore-scale flow focusing with transverse dispersion coefficients is possible only when the entire flow and concentration fields are considered.

54 ENVIRONMENTAL SCIENCES↗

Dynamic optimization and economic evaluation of flexible heat integration in a hybrid concentrated solar power plant

Hybridization of concentrated solar power (CSP) plants provides flexibility in operation that can drastically improve the solar-to-electric (STE) efficiency and levelized cost of electricity (LCOE) relative to standalone CSP plants. Flexible heat integration (FHI) is a novel concept where the collection and integration of CSP within a power plant is modified relative to the amount of solar energy available. FHI improves the thermal efficiency of a hybrid solar tower steam Rankine cycle power plant but leads to increased pumping needs due to continuously elevated molten salt flow rates through the collection system, which can negatively impact STE efficiency. The present work is carried out to maximize the STE efficiency of a hybrid CSP plant utilizing FHI by employing a dynamic optimization framework where a genetic algorithm optimizes the operation of the plant over a given solar irradiance profile. The study concerns a plant hypothetically located in Salt Lake City, Utah. Here, the optimization results confirm the accuracy of a predictive heuristic where the preferred operation of the plant can be estimated relative to local peaks in the incident power generated by the heliostat collection field. The optimized FHI operation demonstrates a yearly STE efficiency of 13.8%, whereas the equivalent base-level hybrid and solar-only plants exhibit solar efficiencies of 13.4% and 11.2%, respectively. Economic analysis shows that FHI reduces yearly natural gas costs, leading to a $\$0.5$/MWh reduction in LCOE relative to the base-level hybrid configuration. Overall, the results show that hybrid FHI schemes exhibit economic benefits along with observed thermodynamic improvements.

14 SOLAR ENERGY↗

A regional scale chemical transport modeling of Asian aerosols with data assimilation of AOD observations using optimal interpolation technique.

A regional chemical transport model assimilated with satellite and ground based aerosol optical depth (AOD) observations was used to produce three dimensional distributions of aerosols throughout Asia for a period of four years. Sulfur Transport dEposition Model (STEM), a regional chemical transport model, was used to simulate aerosol distributions at a resolution of 50x50 km with a time interval of three hours for the entire four years. Monthly mean Moderate Resolution Imaging Spectroradiometer (MODIS) AOD corrected with AErosol RObotic NETwork (AERONET) AOD was used in an optimal interpolation assimilation scheme to yield regional distributions of aerosols. The MODIS AOD and aerosol fine mode fraction information (where available) were used in the assimilation technique. The model was evaluated with daily assimilation of AOD for the month of April 2005 and then the results were compared with mass measurements available at two sites in Asia. The results show that the optimal interpolation algorithm is able to significantly improve model aerosol mass prediction skills at these two sites. Sensitivity studies were also conducted with different assimilation parameters and the results are discussed. The assimilation results of four-year aerosol fields were used to study the spatial and temporal distribution of aerosols in Asia. Two remote sites, Hanimaadhoo and Gosan were chosen as the case studies to study the outflow from the Indian subcontinent and East Asia. Seasonal and vertical structures of the aerosols are presented at these two sites. Positive Matrix Factorization (PMF), a factor analytic method was also used to characterize the source profile and source contribution at these two locations. A three factor solution was able to explain more than 80% of the variation in the individual species at Hanimaadhoo and 90% variation of aerosol loadings at Gosan. The four year averaged PMF model results was able to capture the seasonality of anthropogenic and dust loadings at both these locations.

Adhikary, Bhupesh↗

Chemical reactions, porosity, and microfracturing in shale during weathering: The effect of erosion rate

The rate of chemical weathering has been observed to increase with the rate of physical erosion in published comparisons of many catchments, but the mechanisms that couple these processes are not well understood. We investigated this question in our research by examining the chemical weathering and porosity profiles from catchments developed on marine shale located in Pennsylvania, USA (Susquehanna Shale Hills Critical Zone Observatory, SSHCZO); California, USA (Eel River Critical Zone Observatory, ERCZO); and Taiwan (Fushan Experimental Forest). The protolith compositions, protolith porosities, and the depths of regolith at these sites are roughly similar while the catchments are characterized by large differences in erosion rate (1–3 mm yr ₋1 in Fushan &laquo 0.2–0.4 mm yr ₋1 in ERCZO &laquo 0.01–0.025 mm yr ₋1 in SSHCZO). The natural experiment did not totally isolate erosion as a variable: mean annual precipitation varied along the erosion gradient (4.2 m yr ₋1 in Fushan > 1.9 m yr ₋1 in ERCZO > 1.1 m yr ₋1 in SSHCZO), so the fastest eroding site experiences nearly twice the mean annual temperature of the other two. Even though erosion rates varied by about 100×, the depth of pyrite and carbonate depletion (defined here as regolith thickness) is roughly the same, consistent with chemical weathering of those minerals keeping up with erosion at the three sites. These minerals were always observed to be the deepest to react, and they reacted until 100% depletion. In two of three of the catchments where borehole observations were available for ridges, these minerals weathered across narrow reaction fronts. On the other hand, for the rock-forming clay mineral chlorite, the depth interval of weathering was wide and the extent of depletion observed at the land surface decreased with increasing erosion/precipitation. Thus, chemical weathering of the clay did not keep pace with erosion rate. But perhaps the biggest difference among the shales is that in the fast-eroding sites, microfractures account for 30–60% of the total porosity while in the slow-eroding shale, dissolution could be directly related to secondary porosity. We argue that the microfractures increase the influx of oxygen at depth and decrease the size of diffusion-limited internal domains of matrix, accelerating weathering of pyrite and carbonate under high erosion-rate conditions. Thus, microfracturing is a process that can couple physical erosion and chemical weathering in shales.

58 GEOSCIENCES↗

Using distributed temperature sensing to detect CO 2 leakage along the injection well casing

The objective of this study is to evaluate the sensitivity of Distributed Temperature Sensing (DTS) data to detect CO 2 leakage along an injection well casing. This paper describes the relationship between the CO 2 leakage rate and temperature response at DTS locations, and the method and numerical model used for understanding such a relationship. The uncertainties in the parameters are propagated to the interpretation of DTS measurements, which may lead to false positive and false negative identifications of CO 2 leakage. We propose to identify CO 2 leakage by analyzing both temperature history plots at selected vertical locations as well as the vertical temperature profiles at different times. The analysis should be combined with numerical simulations for the estimation of leakage rates. In addition, leakage needs to be confirmed by data from a warm-up test (temperature recovery after injection of cold CO 2 is stopped) to minimize the probability of false identifications.

42 ENGINEERING↗

Antibacterial dental adhesive resins containing nitrogen-doped titanium dioxide nanoparticles

The development of dental adhesive resins with long-lasting antibacterial properties is a possible solution to overcome the problem of secondary caries in modern adhesive dentistry.Objectives: (i) Synthesis and characterization of nitrogen-doped titanium dioxide nanoparticles (N_TiO 2 ), (ii) topographical, compositional and wettability characterization of thin-films (unaltered and experimental) and, (iii) antibacterial efficacy of N_TiO 2 -containing dental adhesives against Streptococcus mutans biofilms.Materials and methods: Nanoparticles were synthesized and characterized using different techniques. Specimens (diameter = 12 mm, thickness ≅ 15 μm) of OptiBond Solo Plus (Kerr Corp., USA) and experimental adhesives [50, 67 and 80% (v/v)] were fabricated, photopolymerized (1000 mW/cm 2 , 1 min) and UV-sterilized (254 nm, 800,000 μJ/cm 2 ) for microscopy, spectroscopy, wettability and antibacterial testing. Wettability was assessed with a contact angle goniometer by dispensing water droplets (2 μL) onto four random locations of each specimen (16 drops/group). Drop profiles were recorded (1 min, 25 frames/s, 37 °C) and contact angles were calculated at time = 0 s (θ INITIAL ) and time = 59 s (θ FINAL ). Antibacterial testing was performed by growing S. mutans (UA159-ldh, JM10) biofilms for either 3 or 24 h (anaerobic conditions, 37 °C) with or without continuous light irradiation (410 ± 10 nm, 3 h = 38.75 J/cm 2 , 24 h = 310.07 J/cm 2 ) against the surfaces of sterile specimens.Results: N_TiO 2 was successfully prepared using solvothermal methods. Doped-nanoparticles displayed higher light absorption levels when compared to undoped titania. Experimental adhesives demonstrated superior antibacterial efficacy in dark conditions.Conclusions: The findings presented herein suggest that N_TiO 2 is a feasible antibacterial agent against cariogenic biofilms.

36 MATERIALS SCIENCE↗

Links between physical and chemical weathering inferred from a 65-m-deep borehole through Earth’s critical zone

Abstract As bedrock weathers to regolith – defined here as weathered rock, saprolite, and soil – porosity grows, guides fluid flow, and liberates nutrients from minerals. Though vital to terrestrial life, the processes that transform bedrock into soil are poorly understood, especially in deep regolith, where direct observations are difficult. A 65-m-deep borehole in the Calhoun Critical Zone Observatory, South Carolina, provides unusual access to a complete weathering profile in an Appalachian granitoid. Co-located geophysical and geochemical datasets in the borehole show a remarkably consistent picture of linked chemical and physical weathering processes, acting over a 38-m-thick regolith divided into three layers: soil; porous, highly weathered saprolite; and weathered, fractured bedrock. The data document that major minerals (plagioclase and biotite) commence to weather at 38 m depth, 20 m below the base of saprolite, in deep, weathered rock where physical, chemical and optical properties abruptly change. The transition from saprolite to weathered bedrock is more gradational, over a depth range of 11–18 m. Chemical weathering increases steadily upward in the weathered bedrock, with intervals of more intense weathering along fractures, documenting the combined influence of time, reactive fluid transport, and the opening of fractures as rock is exhumed and transformed near Earth’s surface.

58 GEOSCIENCES↗

Time and space resolved visible spectroscopic imaging CO{sub 2} laser produced extreme ultraviolet emitting tin plasmas

Experiments involving laser produced tin plasma have been carried out using a CO{sub 2} laser with an energy of 800 mJ/pulse and a full width at half maximum (FWHM) of 80 ns in vacuum. Time-integrated extreme ultraviolet spectral measurement showed that the peak of the extreme ultraviolet lithography spectrum was located at 13.5 nm and the spectrum profile's FWHM of the unresolved transition arrays was 1.1 nm. Plasma parameters of the electron temperature and density measurements in both axial and radial directions at later times had been obtained from a two-dimensional time and space resolved image spectra analysis. The axial spatial distribution of the electron density showed a 1/d{sup 2.6} decrease profile, and the radial spatial distribution of the electron density showed a 1/r{sup 1.1} profile, in which d is the axial distance from the target surface and r is the radial distance. The electron density was found to maintain symmetry across the radial distance at all delay times. Near the plasma plume center, the electron temperature T{sub e} varied slightly with increasing axial or radial distance, which was related to collisional decoupling and reheating of the ionized species in the plasma at distances longer than 3 to 4 mm. The space averaged electron temperature was measured in the range of 3.4-1.0 eV, and the space averaged electron density was measured in the range of 2.0 x 10{sup 17} to 2.2 x 10{sup 16} cm{sup -3}, as the time delay varied from 1.6 {mu}s to 3.6 {mu}s with respect to the pulse discharge. Time evolutions of the plasma temperature and density were found to have an apparent rise at a delay time of 2.4 {mu}s in the corresponding time of the laser pulse tail peak. This suggests that plasma parameters and extreme ultraviolet emission intensity can be controlled by a double pulse combined laser.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Two-phase flow in a chemically active porous medium

We study the problem of the transformation of a given reactant species into an immiscible product species, as they flow through a chemically active porous medium. We derive the equation governing the evolution of the volume fraction of the species, in a one-dimensional macroscopic description, identify the relevant dimensionless numbers, and provide simple models for capillary pressure and relative permeabilities, which are quantities of crucial importance when tackling multiphase flows in porous media. We set the domain of validity of our models and discuss the importance of viscous coupling terms in the extended Darcy’s law. We investigate numerically the steady regime and demonstrate that the spatial transformation rate of the species along the reactor is non-monotonous, as testified by the existence of an inflection point in the volume fraction profiles. We obtain the scaling of the location of this inflection point with the dimensionless lengths of the problem. Eventually, we provide key elements for optimization of the reactor.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Generation of multiple toroidal dust vortices by a non-monotonic density gradient in a direct current glow discharge plasma

Observation of two well-separated dust vortices in an unmagnetized parallel plate DC glow discharge plasma is reported in this paper. A non-monotonic radial density profile, achieved by an especially designed cathode structure using a concentric metallic disk and ring of different radii, is observed to produce double dust tori between cathode and anode. PIV analysis of the still images of the double tori shows oppositely rotating dust structures between the central disk and the ring. Langmuir probe measurements of background plasma shows a non-uniform plasma density profile between the disk and the ring. Location and sense of rotation of the dust vortices coincides with the location and direction of the radial gradient in the ion drag force caused by the radial density gradient. The experimentally observed dust vorticity matches well with the calculated one using hydrodynamic formulations with shear in ion drag dominating over the dust charge gradient. These results corroborate that a radial gradient in the ion drag force directed towards cathode is the principal cause of dust rotation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

CAVITIES AND SHOCKS IN THE GALAXY GROUP HCG 62 AS REVEALED BY CHANDRA, XMM-NEWTON, AND GIANT METREWAVE RADIO TELESCOPE DATA

We report on the results of an analysis of Chandra, XMM-Newton, and new Giant Metrewave Radio Telescope (GMRT) data of the X-ray bright compact group of galaxies HCG 62, which is one of the few groups known to possess clear, small X-ray cavities in the inner regions. This is part of an ongoing X-ray/low-frequency radio study of 18 groups, initially chosen for the availability of good-quality X-ray data and evidence for active galactic nucleus/hot gas interaction. At higher frequency (1.4 GHz), the HCG 62 cavity system shows minimal if any radio emission, but the new GMRT observations at 235 MHz and 610 MHz clearly detect extended low-frequency emission from radio lobes corresponding to the cavities. By means of the synergy of X-ray and low-frequency radio observations, we compare and discuss the morphology, luminosity, and pressure of the gas and of the radio source. We find that the radio source is radiatively inefficient, with a ratio of radio luminosity to mechanical cavity power of {approx}10{sup -4}, and that the radio pressure of the lobes is about 1 order of magnitude lower than the X-ray pressure of the surrounding thermal gas. Thanks to the high spatial resolution of the Chandra surface brightness and temperature profiles, we also identify a shock front located at 36 kpc to the southwest of the group center, close to the southern radio lobe, with a Mach number {approx}1.5 and a total power which is about 1 order of magnitude higher than the cavity power. Such a shock may have heated the gas in the southern region, as indicated by the temperature map. The shock may also explain the arc-like region of enriched gas seen in the iron abundance map, as this may be produced by a non-Maxwellian electron distribution near its front.

79 ASTRONOMY AND ASTROPHYSICS↗

Genome resequencing reveals demographic history and genetic architecture of seed salinity tolerance in Populus euphratica

Populus euphratica is a dominant tree species in desert riparian forests and possesses extraordinary adaptation to salinity stress. Exploration of its genomic variation and molecular underpinning of salinity tolerance is important for elucidating population evolution and identifying stress-related genes. Here, we identify approximately 3.15 million single nucleotide polymorphisms using whole-genome resequencing. The natural populations of P. euphratica in northwest China are divided into four distinct clades that exhibit strong geographical distribution patterns. Pleistocene climatic fluctuations and tectonic deformation jointly shaped the extant genetic patterns. A seed germination rate-based salinity tolerance index was used to evaluate seed salinity tolerance of P. euphratica and a genome-wide association study was implemented. A total of 38 single nucleotide polymorphisms were associated with seed salinity tolerance and were located within or near 82 genes. Expression profiles showed that most of these genes were regulated under salt stress, revealing the genetic complexity of seed salinity tolerance. Furthermore, DEAD-box ATP-dependent RNA helicase 57 and one undescribed gene (CCG029559) were demonstrated to improve the seed salinity tolerance in transgenic Arabidopsis. These results provide new insights into the demographic history and genetic architecture of seed salinity tolerance in desert poplar.

59 BASIC BIOLOGICAL SCIENCES↗

Direct Numerical Simulation of Involute Channel Turbulence

A direct numerical simulation (DNS) study was performed on turbulent flow in the high flux isotope reactor involute channel geometry to develop a numerical database and determine the differences compared with a flat parallel channel. The varying channel curvature along the walls was studied for differences in mean profiles. Parameters of interest include streamwise velocity, turbulent kinetic energy (TKE), and turbulence dissipation rate, as well as Reynolds stresses and turbulence transport terms. Profile sampling was carried out at 10 locations along the span of the involute. Additional DNS studies were performed on smaller domains of comparable curvature to the involute domain: a high curvature channel (high circular), a low curvature channel (low circular), and a flat channel (flat). Here, each of these four cases was compared against each other and to other DNS studies performed on parallel flows. The results indicate that the bulk involute channel flow does not differ significantly from a flat parallel channel flow and that the curvature of the walls does not significantly alter the mean flow parameters. However, the regions of the involute channel near the side walls exhibit relatively low magnitude twin recirculation structures driven toward the side walls from the centerline of the channel, which warrants further study.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Multi-species impurity granule injection and mass deposition projections in NSTX-U discharges Authors

By employing a neutral gas shielding (NGS) model to characterize impurity granule injection the pedestal atomic deposition for three different species of granule: lithium, boron, and carbon are determined. Utilizing the duration of ablation events recorded on experiments performed at DIII-D to calibrate the NGS model we are able to quantify the ablation rate and mass deposition location with respect to the plasma density profile. The species specific granule shielding constant is then used to model granule ablation within NSTX-U discharges. Simulations of 300, 500 and 700 micron diameter granules injected at 50 m/sec are presented for NSTX-U L-mode type plasmas as well as H-mode discharges with low natural ELM frequencies. Additionally, ablation calculations of 500 micron granules of each species are presented at velocities ranging from 50 - 150 m/sec. In H-mode type discharges these simulations show that the majority of the injected granule is ablated within or just past the steep gradient region of the discharge. At this radial position, the perturbation to the background plasma generated by the ablating granule can lead to conditions advantageous for the rapid triggering of an ELM crash event.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗