Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Laboratory plasma”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Role of E × B Drift in Divertor Detachment Control via Boron Powder Injection on EAST

Here, the effects of B powder injection on plasma detachment about EAST discharge were studied by using SOLPS-ITER code package with the effects of E × B drifts considered. The simulation results show that plasma detachment occurs at the inner target in favourable toroidal magnetic field (B t ) direction at a relatively low B powder flow rate, one order of magnitude lower than that at the outer target. In a similar scenario with unfavourable B t , it is found that the detachment thresholds of B flow rate for both the inner and outer targets are close and of the same order as that for the outer target with favourable Bt. In favourable B t direction at B powder flow rate of 1.2 × 10 21 atoms/s, a localized, broadened high-density region is formed near the inner target benefitted by the injection location and the E × B drift, and a radiation-intensified zone, mostly contributed by B 1+ and B 2+ , occurs there. The E × B drift facilitates plasma detachment at the inner target and simultaneously amplifies the in–out divertor asymmetry. In addition, the simulation results with three different injection locations show that the injection from outer strike point leads to the lowest Z eff inside the separatrix and has an intermediate flow rate for detachment at the outer target, comparing with the X-point and upstream locations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Interpretation of high-harmonic fast-wave propagation in the scrape-off layer of NSTX-U as a geometrically bounded-waveguide mode

This paper revisits the onset of high-harmonic fast-wave (HHFW) propagation in the scrape-off layer (SOL) plasma of the NSTX/NSTX-U spherical tokamak, motivated by past HHFW heating and current drive experiments and modelling. Previously, the fast-wave propagation in the SOL was correlated with the opening (suppression) of the fast-wave right-hand cutoff layer in front of the antenna. In this work, the SOL propagation is interpreted as a geometric waveguide mode guided by the SOL geometry, whose radial width can be comparable to the wave’s perpendicular wavelength in the HHFW regime. A two-dimensional circular model is first employed using full-wave solvers to characterise the poloidal eigenmode structures and to clarify their relationship to annulus resonance. By progressively adding a tokamak-like magnetic-field configuration, starting from a uniform axial field, the effects of magnetic-field gradients and pitch on the SOL waveguide mode are characterised. The poloidal mode numbers supported by the SOL plasma agree well with analytic estimates, indicating that an anisotropic plasma in a bounded geometry selectively supports and amplifies the resonant poloidal mode number. Additionally, two-dimensional axisymmetric NSTX-U simulations demonstrate that the SOL eigenmode features identified in the circular model persist in the experimentally relevant configurations. A control approach based on lengthening the wave perpendicular wavelength relative to the SOL width, including a higher magnetic (B)-field operation, is discussed. The analysis here shows the key role of a bounded geometry in interpreting HHFW eigenmode coupling and propagation in the NSTX-U SOL plasma.

plasma heating↗
DOE OSTI2025

Application of Lagrangian techniques for calculating the on-axis rotational transform

The Floquet exponents of periodic field lines are studied through the variations of the magnetic action on the magnetic axis, which is assumed to be elliptical. The near-axis formalism developed by Mercier, Solov'ev and Shafranov is combined with a Lagrangian approach. The on-axis Floquet exponent is shown to coincide with the on-axis rotational transform. A discrete solution suitable for numerical implementation is introduced, which gives the Floquet exponents as solutions to an eigenvalue problem. This discrete formalism expresses the exponents as the eigenvalues of a $6$ X $6$ matrix.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Decomposition of methane diluted with inert gas in an RF discharge cell

Decomposition of methane using non-thermal plasmas is an attractive route for producing hydrogen-rich gases and valuable carbon nanomaterials. Understanding how plasma discharge modes influence methane decomposition in optimizing plasma-assisted chemical conversion remains unexplored. This study explores the coupling between the discharge structure and product selectivity in RF capacitively coupled discharges operating in methane/inert gas mixtures in the pressure range of 2–3 torr. Under our experimental conditions the discharge exhibits mode transitions from uniform to striated in Ar and Kr and from diffuse to contracted in Ar and Kr with <5% CH 4 . The discharges in He and Ne remained uniform under our operating conditions, and their mixtures with CH 4 remained diffuse. A 0-d model for Ar/CH 4 discharge established a threshold for contraction while also asserting the importance of Ar$^{*}_{\textrm{m}}$ in the dissociation and ionization processes. The highest degree of methane decomposition, >99.7% with the main products of acetylene and graphitized solid carbon was achieved in the contracted discharge mode for both Kr or Ar with ⩽5% CH 4 . We demonstrate that contraction can play a crucial role in the effective decomposition of methane with value-added products and that both the electronic and thermal properties of plasma gas are responsible for this effect.

RF plasma↗
DOE OSTI2019

Retrieving fields from proton radiography without source profiles

Proton radiography is a technique in high-energy density science to diagnose magnetic and/or electric fields in a plasma by firing a proton beam and detecting its modulated intensity profile on a screen. Current approaches to retrieve the integrated field from the modulated intensity profile require the unmodulated beam intensity profile before the interaction, which is rarely available experimentally due to shot-to-shot variability. In this paper, we present a statistical method to retrieve the integrated field without needing to know the exact source profile. We apply our method to experimental data, showing the robustness of our approach. Furthermore, our proposed technique allows for the retrieval not only of the path-integrated fields, but also of the statistical properties of the fields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Partially Ionized Plasma Physics and Technological Applications

Partially ionized plasma physics has attracted increased attention recently due to numerous technological applications made possible by the increased sophistication of computer modelling, the depth of the theoretical analysis, and the technological applications to a vast field of manufacturing for computer components. Partially ionized plasma is characterized by a significant presence of neutral particles in contrast to the fully ionized plasma. The theoretical analysis is based upon solutions of the kinetic Boltzmann equation, yielding the non-Maxwellian electron energy distribution function (EEDF), thereby emphasizing the difference with a fully ionized plasma. The impact of the effect on discharges in inert and molecular gases is described in detail, yielding the complex nonlinear phenomena resulting in plasma selforganization. A few examples of such phenomena are given, including the non-monotonic EEDFs in the discharge afterglow in a mixture of argon with the molecular gas NF3; the explosive generation of cold electron populations in capacitive discharges, hysteresis of EEDF in inductively coupled plasmas. Recently, highly advanced computer codes were developed in order to address the outstanding challenges in plasma technology. These developments are briefly described in general terms.

non-Maxwellian electron energy distribution functi↗
DOE OSTI2025

Data for reproducing the figures of the paper Multimodal Super-Resolution: Discovering hidden physics and its application to fusion plasmas

This deposit contains the raw data for reproducing research results of the paper Multimodal Super-Resolution: Discovering hidden physics and its application to fusion plasmas. The main contribution of this work is to utilize machine learning techniques to reconstruct and enhance the resolution of a diagnostic measurement from other available diagnostics in a system. The proposed techniques is called Diag2Diag.

diag2diag↗
DOE OSTI2025

A Grassroots Network and Community Roadmap for Interconnected Autonomous Science Laboratories for Accelerated Discovery

Scientific discovery is being revolutionized by AI and autonomous systems, yet current autonomous laboratories remain isolated islands unable to collaborate across institutions. We present the Autonomous Interconnected Science Lab Ecosystem (AISLE), a grassroots network transforming fragmented capabilities into a unified system that shorten the path from ideation to innovation to impact and accelerates discovery from decades to months. AISLE addresses five critical dimensions: (1) cross-institutional equipment orchestration, (2) intelligent data management with FAIR compliance, (3) AI-agent driven orchestration grounded in scientific principles, (4) interoperable agent communication interfaces, and (5) AI/ML-integrated scientific education. By connecting autonomous agents across institutional boundaries, autonomous science can unlock research spaces inaccessible to traditional approaches while democratizing cutting-edge technologies. This paradigm shift toward collaborative autonomous science promises breakthroughs in sustainable energy, materials development, and public health.

Ferreira da Silva, Rafael [Oak Ridge National Labo↗
DOE OSTI2025

Advancing Fusion Research and Development at TAE Technologies Through INFUSE Program

The U.S. Department of Energy’s Innovation Network for Fusion Energy (INFUSE) program serves as a crucial catalyst by fostering public-private partnership that accelerates technological innovation for fusion energy research and development (R&D) in the private sector. Further, this article provides a comprehensive overview of the technical goals and accomplishments of projects awarded to TAE Technologies through the INFUSE program since 2019. We offer high-level perspectives on how these projects have contributed to fusion energy R&D, and we address key challenges encountered during these collaborations.

field-reversed configuration↗
DOE OSTI2025

Deep potential molecular dynamics simulations of low-temperature plasma-surface interactions

Machine learning approaches to potential generation for molecular dynamics (MD) simulations of low-temperature plasma-surface interactions could greatly extend the range of chemical systems that can be modeled. Empirical potentials are difficult to generalize to complex combinations of multiple elements with interactions that might include covalent, ionic, and metallic bonds. This work demonstrates that a specific machine learning approach, Deep Potential Molecular Dynamics (DeepMD), can generate potentials that provide a good model of plasma etching in the Si-Cl-Ar system. Comparisons are made between MD results using DeepMD models and empirical potentials, as well as experimental measurements. Pure Si properties predicted by the DeepMD model are in reasonable agreement with experimental results. Simulations of Si bombardment by Ar + ions demonstrate the ability of the DeepMD method to predict sputtering yields as well as the depth of the amorphous-crystalline interface. Etch yields as a function of flux ratio and ion energy for simultaneous Cl 2 and Ar + impacts are in good agreement with previous simulation results and experiment. Predictions of etch yields and etch products during plasma-assisted atomic layer etching of Si-Cl 2 -Ar are shown to be in good agreement with MD predictions using empirical potentials and with experiment. Finally, good agreement was also seen with measurements for the spontaneous etching of Si by Cl atoms at 300 K. Further, the demonstration that DeepMD can reproduce results from MD simulations using empirical potentials is a necessary condition to future efforts to extend the method to a much wider range of systems for which empirical potentials may be difficult or impossible to obtain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Experimental Setup to Investigate Hydrogen Isotope Retention on Powder Samples as Slag/Dust Proxies for Advanced Fusion Reactors

Slag/dust formation is one of the critical issues regarding tritium retention in advanced fusion reactors. We upgraded an ultrahigh vacuum device, the sample exposure station (SES), to perform temperature-programmed desorption (TPD), also known as thermal desorption spectroscopy, to investigate deuterium (D) retention in powder samples that are utilized as proxies for slag/dust particles formed in fusion reactors. TPD analysis, calibrated for the desorption rate, was successfully performed on commercially available crystalline/amorphous boron (B) powder after D 2 neutral gas or D + ion exposure. We calibrated the B powder temperature measurement for TPD analysis utilizing a D 2 desorption peak from B-D bonding known for its desorption temperature ~700 K. We introduce a separation procedure of observed D TPD signals, convoluted for corresponding D retention pathways, that was necessary for TPD analysis. This is the first report on the retention of D 2 neutral gas to B, and this observation was enabled by utilizing the B powder sample, which has a larger surface area than films commonly used in laboratory experiments. In conclusion, the upgraded SES system will enable us to investigate hydrogen isotope behaviors for powder/dust samples of various elemental compositions, including metals.

Plasma-facing component debris↗
DOE OSTI2026

Characterization of ELM pacing via vertical jogs on DIII-D

Edge localized mode (ELM) pacing via vertical plasma oscillations or jogging has been successfully demonstrated on DIII-D. Rapid vertical movement of the plasma toward the X-point has been shown to effectively trigger ELMs. By vertically oscillating the plasma at a rate of 10 Hz, the ELM frequency increased from ~5 Hz, the natural ELM frequency in similar DIII-D discharges, to 20 Hz. Downward jogs have been observed to trigger multiple ELMs in one cycle. ELMs triggered at higher than natural frequencies lead to smaller decreases in stored energy, from 8% to as little as below 1%. As a consequence, the peak heat flux to the divertor has been observed to be reduced by a factor of ~2. In addition, a reduction in the carbon impurity concentration has been observed. During downward jogs in the lower single null (LSN) configuration, the X-point movement is slower and smaller than the top of the plasma. As a result, a reduction in the plasma cross-section and hence volume has been observed. To understand the mechanism of ELM triggering by jogging, a toy model of the edge toroidal current has been built and tested with DIII-D experiment data. The experimental data and model suggest that when the plasma moves down toward the X-point, a net positive toroidal current is locally induced in the edge region. ELITE stability analysis suggests that this current pushes the plasma state across the peeling side of the peeling–ballooning stability boundary into the unstable region triggering ELMs.

ELM pacing↗
DOE OSTI2025

Zero curvature is a necessary and sufficient condition for a spin-orbital decomposition

There has been an extended debate regarding the existence of a spin-orbital decomposition of the angular momentum of photons and other massless particles. It was recently shown that there are both geometric and topological obstructions preventing any such decomposition. Here we show that any geometric connection on a particle’s state space induces a splitting of the angular momentum into two operators. These operators are well-defined angular momentum operators if and only if the connection has zero curvature. Massive particles have two canonical curved connections corresponding to boosts and rotations, respectively. Furthermore, these can be uniquely combined to produce a flat connection, and this gives a novel derivation of the Newton-Wigner position operator and the corresponding spin and orbital angular momenta for relativistic massive particles. When the mass is taken to zero, transverse boosts and rotations degenerate, leaving only a single connection for massless particles. This connection produces a commonly proposed splitting of the massless angular momentum into two operators. However, the connection is not flat, explaining why these operators do not satisfy the angular momentum commutation relations and are thus not true spin and orbital angular momentum operators.

Angular momentum↗
DOE OSTI2025

Four no-go theorems on the existence of spin and orbital angular momentum of massless bosons

The past decades have seen substantial interest in the so-called orbital angular momentum (OAM) of light, driven largely by its diverse range of applications. However, there are fundamental theoretical issues with decomposing the angular momentum of massless particles, such as photons, into spin (SAM) and orbital angular momentum parts. While the angular momentum of massive particles has a natural splitting into the Wigner SAM and OAM, there are numerous proposed splittings for photons and no consensus about which is correct. Moreover, it has been shown that most of the proposed SAM and OAM operators do not satisfy the defining commutation relations of angular momentum operators and are thus not legitimate splittings. Here, we prove that it is generally impossible to split the total angular momentum operator of massless bosons, such as photons and gravitons, into spin and orbital parts. We prove two further generalizations of this result, showing that there are no SAM-OAM splittings even if (1) the SAM operator generates non-internal symmetries or (2) if one allows the SAM and OAM operators to generate non-SO(3) symmetries.

Chern numbers↗
DOE OSTI2025

PaleoSTeHM v1.0: a modern, scalable spatiotemporal hierarchical modeling framework for paleo-environmental data

Abstract. Geological records of past environmental change provide crucial insights into long-term climate variability, trends, non-stationarity, and nonlinear feedback mechanisms. However, reconstructing spatiotemporal fields from these records is statistically challenging due to their sparse, indirect, and noisy nature. Here, we present PaleoSTeHM, a scalable and modern framework for spatiotemporal hierarchical modeling of paleo-environmental data. This framework enables the implementation of flexible statistical models that rigorously quantify spatial and temporal variability from geological data while clearly distinguishing measurement and inferential uncertainty from process variability. We illustrate its application by reconstructing temporal and spatiotemporal paleo-sea-level changes across multiple locations. Using various modeling and analysis choices, PaleoSTeHM demonstrates the impact of different methods on inference results and computational efficiency. Our results highlight the critical role of model selection in addressing specific paleo-environmental questions, showcasing the PaleoSTeHM framework's potential to enhance the robustness and transparency of paleo-environmental reconstructions.

58 GEOSCIENCES↗
DOE OSTI2025

Hydrodynamic expansion and near-infrared absorption of x-ray heated aluminum plasmas

We use x-ray pulses from dense argon plasmas at the Z Machine (Sandia National Laboratories) to generate hypersonic aluminum plasmas akin to material ejecta during proposed planetary defense missions, fusion reactor wall excursions, and other high-energy density processes. Near-infrared absorption is used to diagnose the controlled expansion of the plasmas through cylindrical cavities following their generation from x-ray heating of solid aluminum 7075 alloy. The data are compared to multidimensional radiation hydrodynamics simulations utilizing the ALEGRA multiphysics code, accounting for the dynamics of radiation scattering, material phase change, plasma expansion, thermal re-irradiation, and interactions with the cavity and with the infrared beams. To allow for accurate simulation, density functional theory is used to apply the Hagen–Rubens relation for the far-infrared and is adjoined with a detailed configuration accounting model using the Propaceos code, producing opacities spanning 10 −1 –10 4 eV photon energy for aluminum 7075 alloy, and in comparison with pure aluminum. The model is found to agree with experimental data in the higher-fluence regime when the Hagen–Rubens relation is applied. The ejected material, which is observed to travel up to 55 km/s, is comprised of a strongly ionized, non-LTE plasma front at ∼10 eV temperature followed by a weakly ionized LTE gas at higher density. The present findings lend some confidence to the broad-range equation of state and infrared opacity models for weakly ionized aluminum plasmas while demonstrating an approach to their future refinement, with potential application to astrophysical plasmas and other extreme processes.

Adiabatic process↗
DOE OSTI2025

Interactions of a Microdischarge with a Premixed Flame (Final Technical Report)

In this project we introduced an experimental platform that facilitates the study of the two-way interaction of plasma and flame, and the exploration of the impact of the spatial location of the discharge on its kinetics, in a controlled environment. The experimental platform is a mesoscale CH4/air premixed flame burner that also acts as a dielectric barrier discharge (DBD) operated by nanosecond pulsed voltage. A unique feature of this setup is that the DBD utilizes transparent electrodes, made of Indium Tin Oxide (ITO), to unlock optical access along the line-of-sight parallel to the dominant electric field. This platform is suitable to study both the forward problem (impact of plasma-on-flame), which manifests itself as a modified flame speed as well as flame wrinkling; and the backward problem (impact of flame-on-plasma), which includes plasma regime transitions, between microdischarges and uniform modes, driven by the flame passage. Prior work at MIT has focused on electrical measurements and direct imaging studies of the plasma-flame interaction through the ITO electrode. This project, which was awarded experimental runtime at the Low-temperature Plasma Research Facility (PRF) at Sandia National Laboratories, quantifies the flame-plasma interaction through temporally resolved measurement of key radicals (oxygen atom, O) produced by the nanosecond repetitively pused discharge (NRPD) in an individual microdischarge, using two-photon absorption laser-induced fluorescence (TALIF).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗