Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “JUNCTION DIODE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Light-trapping design for thin-film silicon-perovskite tandem solar cells

Using finite-difference time-domain simulations, we investigate the optical properties of tandem silicon/perovskite solar cells with a photonic crystal architecture, consisting of a square-lattice array of inverted pyramids with a center-to-center spacing of 2.5 μm. Here, we demonstrate that near-perfect light-trapping and absorption can be achieved over the 300–1100 nm wavelength range with this architecture, using less than 10 μm (equivalent bulk thickness) of crystalline silicon. Using a one-diode model, we obtain projected efficiencies of over 30% for the two-terminal tandem cell under a current-matching condition, well beyond the current record for single-junction silicon solar cells. Lastly, the architecture is amenable to mass fabrication through wet-etching and uses a fraction of the silicon of traditional designs, making it an attractive alternative to other silicon-perovskite tandem designs.

14 SOLAR ENERGY↗

Diffusion length measurements in bulk and epitaxially grown 3-5 semiconductors using charge collection microscopy

Diffusion lengths and surface recombination velocities were measured in GaAs diodes and InP finished solar cells. The basic techniques used was charge collection microscopy also known as electron beam induced current (EBIC). The normalized currents and distances from the pn junction were read directly from the calibrated curves obtained while using the line scan mode in an SEM. These values were then equated to integral and infinite series expressions resulting from the solution of the diffusion equation with both extended generation and point generation functions. This expands previous work by examining both thin and thick samples. The surface recombination velocity was either treated as an unknown in a system of two equations, or measured directly using low e(-) beam accelerating voltages. These techniques give accurate results by accounting for the effects of surface recombination and the finite size of the generation volume.

Leon, R. P.↗

Diffusion length measurement in bulk and epitaxially grown III-V semiconductors using charge collection microscopy

Diffusion lengths and surface recombination velocities were measured in GaAs diodes and InP finished solar cells. The basic technique used was charge collection microscopy, also known as electron beam induced current (EBIC). The normalized currents and distances from the pn junction were read directly from the calibrated curves obtained while using the line-scan mode in an SEM. These values were then equated to integral and infinite series expressions resulting from the solution of the diffusion equation with both extended-generation and point-generation functions. This expands previous work by examining both thin and thick samples. The surface recombination velocity was either treated as an unknown in a system of two equations or measured directly using low e(-) beam accelerating voltages. These techniques give accurate results by accounting for the effects of surface recombination and the finite size of the generation volume.

Leon, R. P.↗

Current rectification based on noncentrosymmetric quantum materials

Rectification is a process that converts electromagnetic fields into direct current (DC). Such a process underlies a wide range of technologies, including wireless communication, wireless charging, energy harvesting, and infrared detection. Existing rectifiers are mostly based on semiconductor diodes, with limited applicability to small voltages or high frequency inputs. Here, we present an alternative approach to current rectification that uses the electronic properties of quantum crystals without semiconductor junctions. We identify a new mechanism for rectification from skew scattering due to the chirality of itinerant electrons in time-reversal-invariant but inversion-breaking materials. Our calculations reveal large, tunable rectification effects in graphene multilayers and transition metal dichalcogenides. These effects can be used in high-frequency rectifiers by rational material design and quantum wavefunction engineering.

Isobe, Hiroki↗

The ZnO p-n homojunctions modulated by ZnMgO barriers

In this paper, we fabricated the ultrathin ZnO p-n homojunctions, which modulated by ZnMgO asymmetrical double barriers (ADB). The ADB p-n homojunctions displays step-like curve in the absorption spectrums, this is the first time that quantum confinement effect has been observed in the absorption spectrums at room temperature (RT). The Hall-effect data confirm there is 2-dimensional electron gas in the interface of the ZnMgO ADB p-n junctions. The quantum confinement effect enhances the hall-mobility μ to 10{sup 3} cm{sup 2}V {sup −1}s{sup −1} based on the polarity of the films. There was no rectification property in the ZnO homojunctions with thickness of 250nm, however, when the ADB was added in the n-type layer of the homojunctions, it displays a typical Zener diode rectification property in the I-V curve.

36 MATERIALS SCIENCE↗

Al0 0.3 Ga 0.7 N PN diode with breakdown voltage >1600 V

Demonstration of Al0 0.3 Ga 0.7 N PN diodes grown with breakdown voltages in excess of 1600 V is reported. The total epilayer thickness is 9.1 μm and was grown by metal-organic vapour-phase epitaxy on 1.3-mm-thick sapphire in order to achieve crack-free structures. A junction termination edge structure was employed to control the lateral electric fields. A current density of 3.5 kA/cm 2 was achieved under DC forward bias and a reverse leakage current <3 nA was measured for voltages <1200 V. The differential on-resistance of 16 mΩ cm 2 is limited by the lateral conductivity of the n-type contact layer required by the front-surface contact geometry of the device. An effective critical electric field of 5.9 MV/cm was determined from the epilayer properties and the reverse current–voltage characteristics. To our knowledge, this is the first aluminium gallium nitride (AlGaN)-based PN diode exhibiting a breakdown voltage in excess of 1 kV. Finally, we note that a Baliga figure of merit (V br 2 /R spec,on ) of 150 MW/cm 2 found is the highest reported for an AlGaN PN diode and illustrates the potential of larger-bandgap AlGaN alloys for high-voltage devices.

36 MATERIALS SCIENCE↗

Improving 2D Schottky contacts using an intralayer strategy

An additional insulating layer between the electrode and semiconductor is beneficial to reduce the interfacial coupling and build two-dimensional (2D) Schottky contacts. Here, an intralayer strategy was proposed by using metallic 2D Bi 2 Sr 2 CaCu 2 O 8+δ (BSCCO) as contacts on 2D semiconductors. Inside a BSCCO monolayer, a conductive layer is sandwiched between insulating layers. Thus, the BSCCO contact has its own insulating layer, which is ultra-thin, single crystalline, and of high quality. This native layer could reduce the metal-induced gap state and thus weaken the interfacial Fermi level pinning effect. Such 2D Schottky diodes thus have barrier heights of 300 mV and a rectification ratio of 104. Furthermore, 2D metal-semiconductor field-effect transistors with BSCCO Schottky gate have a high on-off ratio, low leakage current, and low subthreshold swing value near the theoretical limit. The intralayer structure offers a new approach to improve the 2D Schottky junctions and has prospects in 2D electronics and optoelectronics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Laser diode with thermal conducting, current confining film

A laser diode formed of a rectangular parallelopiped body of single crystalline semiconductor material includes regions of opposite conductivity type indium phosphide extending to opposite surfaces of the body. Within the body is a PN junction at which light can be generated. A stripe of a conductive material is on the surface of the body to which the P type region extends and forms an ohmic contact with the P type region. The stripe is spaced from the side surfaces of the body and extends to the end surfaces of the body. A film of germanium is on the portions of the surface of the P type region which is not covered by the conductive stripe. The germanium film serves to conduct heat from the body and forms a blocking junction with the P type region so as to confine the current through the body, across the light generating PN junction, away from the side surfaces of the body.

Hawrylo, Frank Z.↗

Effect of Annealing Conditions on Recovery of Lattice Damage in a High-Energy-Implanted 4H-SiC Superjunction PIN Diode

A high energy ion implantation system has been recently developed at the Tandem Van de Graaff facility at Brookhaven National Laboratory with tunable energy to 150 MeV capable of multi-step, deep implantation in 4H-SiC wafers with dopant atoms, such as B, P, Al, and N. Medium and high voltage devices with deep junctions can be fabricated using this system. Lattice strain introduced by the implantation process needs to be recovered and dopant atoms activated by appropriate annealing process as the device performance is strongly associated with the extent of recovery of the lattice. Using Synchrotron X-ray Rocking Curve Topography (SXRCT) and Reciprocal Space Mapping (RSM), the strain induced by high energy implantation of Al and N in 4H-SiC in different patterns are measured and mapped. It is observed that the strain levels correlate with the total fluence levels. PiN diodes fabricated on these implanted wafers were then annealed at temperatures ranging from 1700 °C to 2000 °C for 60 min. The SXRCT and RSM analysis of the annealed samples suggests that for the same annealing duration, higher temperature leads to better lattice recovery.

43 PARTICLE ACCELERATORS↗

Emission color-tuned light-emitting diode microarrays of nonpolar In x Ga 1–x N/GaN multishell nanotube heterostructures

Integration of nanostructure lighting source arrays with well-defined emission wavelengths is of great importance for optoelectronic integrated monolithic circuitry. We report on the fabrication and optical properties of GaN-based p–n junction multishell nanotube microarrays with composition-modulated nonpolar m-plane In x Ga 1–x N/GaN multiple quantum wells (MQWs) integrated on c-sapphire or Si substrates. The emission wavelengths were controlled in the visible spectral range of green to violet by varying the indium mole fraction of the In x Ga 1–x N MQWs in the range 0.13 ≤ x ≤ 0.36. Homogeneous emission from the entire area of the nanotube LED arrays was achieved via the formation of MQWs with uniform QW widths and composition by heteroepitaxy on the well-ordered nanotube arrays. Importantly, the wavelength-invariant electroluminescence emission was observed above a turn-on of 3.0 V because both the quantum-confinement Stark effect and band filling were suppressed due to the lack of spontaneous inherent electric field in the m-plane nanotube nonpolar MQWs. Lastly, the method of fabricating the multishell nanotube LED microarrays with controlled emission colors has potential applications in monolithic nonpolar photonic and optoelectronic devices on commonly used c-sapphire and Si substrates.

36 MATERIALS SCIENCE↗

Direct-bandgap electroluminescence from a horizontal Ge p-i-n ridge waveguide on Si(001) substrate

Horizontal injection Ge p-i-n ridge waveguide light emitting diodes (LEDs) were fabricated on n{sup −}-Si(001) substrates by ultrahigh vacuum chemical vapor deposition. The direct-bandgap electroluminescence (EL) of Ge waveguide LEDs under a continuous/pulse electrical pump was studied. The heating effect from a continuous electrical pump was found to significantly enhance the emission of devices. The top surface EL intensity of the Ge waveguide LEDs significantly depended on the position. Most direct-bandgap radiative recombination of Ge p-i-n waveguide LEDs occurred near the N{sup +} region of the junction. This interesting phenomenon could be explained by the carrier distribution in the junction and the pseudo-direct bandgap of Ge.

36 MATERIALS SCIENCE↗

Buck/boost regulator

A voltage regulated DC to DC converter uses an inductor and a capacitor as storage elements. The inductor is composed of two windings having a common junction. A transformer with a center tap connected to the common junction of the two windings is connected at either end of its winding to ground through controlled switches. One winding of the inductor and either end of the transformer winding are connected by power diodes to the capacitor which supplies the output voltage to a load. The other winding of the inductor is connected to a fourth power diode as a clamping diode. Input voltage is supplied to the inductor through a third controlled switch. A pulse width modulator connected to the output of the converter alternately closes and opens the switches connected to either end of the transformer winding and also closes the switch supplying input voltage to the inductor each time either of the switches connected to the ends of the transformer winding are closed. The duty cycle of the closing and opening of the several switches is adjusted by the pulse modulator to regulate the output voltage.

Paulkovich, J.↗

Submicron nickel-oxide-gold tunnel diode detectors for rectennas

The characteristics of a metal-oxide-metal (MOM) tunnel diode made of nickel, nickel-oxide, and gold, designed and fabricated by standard integrated circuit technology for use in FIR rectennas, are presented. The MOM tunnel diode was formed by overlapping a 0.8-micron-wide layer of 1000-A of nickel, which was oxidized to form a thin layer of nickel oxide, with a 1500 A-thick layer of gold. The dc current-voltage characteristics of the MOM diode showed that the current dependence on voltage was linear about zero bias up to a bias of about 70 mV. The maximum detection of a low-level signal (10-mV ac) was determined to be at a dc voltage of 70 mV across the MOM diode. The rectified output signal due to a chopped 10.6-micron CO2 laser incident upon the rectenna device was found to increase with dc bias, with a maximum value of 1000 nV for a junction bias of 100 mV at room temperature.

Hoofring, A. B.↗

Origin of electrons emitted into vacuum from InGaN light emitting diodes

The mechanism responsible for efficiency droop in InGaN light-emitting diodes (LEDs) has long been elusive due to indirect measurement techniques used for its identification. Auger recombination is unique among proposed efficiency droop mechanisms, in that it is the only mechanism capable of generating hot carriers. In a previous study [J. Iveland et al., Phys. Rev. Lett. 110, 177406 (2013)], we performed electron energy analysis of electrons emitted into vacuum from a forward biased InGaN LED that had been brought into negative electron affinity by cesiation. Three peaks were observed in the energy spectrum of vacuum emitted electrons. In this Letter, we unambiguously identify the origin of the peaks. The two higher energy peaks correspond to accumulation of electrons transported to the surface in the bulk Γ and side L conduction band valleys. The L-valley peak is a direct signature of a hot Auger electron population. The lower energy peak results from surface photoemission induced by the internal LED light emitted from the InGaN quantum wells. Two control experiments were performed. In the first, a simple GaN pn junction generated only a single Γ peak in electroemission. In the second, selective detection of the photoemission from an LED under modulated light excitation and DC electrical injection confirms that only the low energy peak is photogenerated and that LED light is incapable of generating Γ or L-valley peaks, the latter only occurring due to the Auger effect in the LED active region.

42 ENGINEERING↗

Closing the Accuracy Gap in Tandem Photovoltaic Testing: An Accessible and Efficient Spectral Tuning Method Using LED-Based Simulators for Research Laboratories and Industry

Accurate performance calibration of multijunction (MJ) solar cells is critical for advancing this technology toward large-scale terrestrial application, yet existing testing methods developed by photovoltaics calibration laboratories remain prohibitively complex and resource intensive for most research laboratories. Current approaches rely on expensive multisource simulators and/or intricate spectral tuning algorithms, limiting accessibility and hindering standardized comparisons of emerging MJ technologies such as perovskite-based tandems. This paper introduces a streamlined spectral irradiance adjustment method for light-emitting diode (LED)-based solar simulators, which are increasingly adopted in the photovoltaics community due to their versatility and cost-effectiveness. The method we present bins LED channels into groups based on the number of junctions of the MJ photovoltaic device under test (DUT) and their corresponding band gaps and incorporates an automated tuning algorithm that eliminates the need to adjust each channel’s irradiance individually. This tuning algorithm requires the relative spectral responsivities of both the DUT and a broadband reference cell, as well as a calibrated spectroradiometer. Measurement validation across various MJ devices, including III-V and perovskite/silicon tandems, demonstrates excellent agreement within 1% with well-established xenon-tungsten multisource simulators and associated tuning algorithms. By enabling precise spectral tuning with readily available equipment and a simple tuning algorithm, our approach bridges the measurement accuracy gap between research laboratories and accredited testing facilities, fostering more reliable device comparisons and accelerating the translation of MJ technologies into real-world energy systems.

14 SOLAR ENERGY↗

Remote heteroepitaxy of GaN microrod heterostructures for deformable light-emitting diodes and wafer recycle

There have been rapidly increasing demands for flexible lighting apparatus, and micrometer-scale light-emitting diodes (LEDs) are regarded as one of the promising lighting sources for deformable device applications. Herein, we demonstrate a method of creating a deformable LED, based on remote heteroepitaxy of GaN microrod (MR) p - n junction arrays on c -Al 2 O 3 wafer across graphene. The use of graphene allows the transfer of MR LED arrays onto a copper plate, and spatially separate MR arrays offer ideal device geometry suitable for deformable LED in various shapes without serious device performance degradation. Moreover, remote heteroepitaxy also allows the wafer to be reused, allowing reproducible production of MR LEDs using a single substrate without noticeable device degradation. The remote heteroepitaxial relation is determined by high-resolution scanning transmission electron microscopy, and the density functional theory simulations clarify how the remote heteroepitaxy is made possible through graphene.

36 MATERIALS SCIENCE↗

Metal-oxide-metal point contact junction detectors

The detection mechanism(s) and design of a mechanically stable metal-oxide-metal point contact junction detector are considered. A prototype for a mechanically stable device has been constructed and tested. A technique has been developed which accurately predicts microwave video detector and heterodyne mixer SIM (semiconductor-insulator-metal) diode performance from low dc frequency volt-ampere curves. The difference in contact potential between the two metals and geometrically induced rectification constitute the detection mechanisms.

Baird, J.↗

Transport of majority and minority carriers in 2-micron-diameter Pt-GaAs Schottky barriers

An experimental study of small area (2-micron diameter) Pt-GaAs Schottky barrier diodes has been made, by using a wafer chip with a matrix of these diodes lying within approximately a minority carrier diffusion length of one another. Using one diode as collector and another as emitter, transistor measurements indicated that the dominant contribution to the current is the majority-carrier thermionic field emission current for large forward-bias voltage of the emitter junction (V-EB no less than about 0.4 V), whereas the smaller forward-bias (V-EB no greater than about 0.4 V) recombination in the space-charge region was most important. The minority carrier injection ratio is measurable only for large forward-bias voltages, decreasing from about 0.02 to 0.00001 as VEB increases from 0.5 to 1.0 V. The minority carrier diffusion length was measured to be about 1.3 microns. These results are of considerable significance for the understanding and optimization of the performance of these devices as classical detectors and mixers.

Chan, E. Y.↗