Results for “GaS” — Page 29

NASA NTRS2020

Transmutations Observed from Pressure Cycling Palladium Silver Metals with Deuterium Gas

Hydrogen, deuterium, and helium gases were separately cycled through a Johnson-Mattheypurifier containing coiled palladium silver alloy tubing: Pd25Ag (75 wt% Pd and 25 wt% Ag).During the cycling of D2 gas, evidence of anomalous heat production was observed. However,during the cycling of H2 and He,very little (H2) or no (He) unusual heat events were observed.After cycling the D2 gas through the coiled tubing for several months, Pd25Ag samples showedan increase in Cu and Fe compared with the amounts in unexposed Pd25Ag. Chromium,manganese, and zinc were detected in gas-cycled Pd25Ag samples, whereas they were notdetected in unexposed Pd25Ag samples. In particular, Zn was present in the gas-cycled Pd25Agmaterial in larger quantities than either Cr or Mn. Although a small amount of Cu was present inthe Pd25Ag coil before the D2 gas cycling, 7 times more was present after the cycling. Multiplematerial characterization techniques were used to obtain both pre-test and post-test elementalcomposition. The results indicate that novel post-test elements, primarily on the surface, werecreated by unknown nuclear mechanisms at low energy.

Gustave C Fralick↗

NASA NTRS2021

Photoionization Models for High Density Gas

Relativistically broadened and redshifted 6.4 – 6.9 keV iron K lines are observed from many accretion powered objects, including X-ray binaries and active galactic nuclei(AGN). Existence of gas close to the central engine implies large radiation intensities and correspondingly large gas densities if the gas is to remain partially ionized. Simple estimates indicate that high gas densities are needed to allow survival of iron against ionization. These are high enough that rates for many atomic processes are affected by mechanisms related to interactions with nearby ions and electrons. Radiation intensities are high enough that stimulated processes can be important. Most models currently in use for interpreting relativistic lines use atomic rate coefficients designed for use at low densities and neglect stimulated processes. In our work so far we have presented atomic structure calculations with the goal of providing physically appropriate models at densities consistent with line-emitting gas near compact objects. In this paper we apply these rates to photoionization calculations, and produce ionization balance curves and X-ray emissivities and opacities which are appropriate for high densities and high radiation intensities. The final step in our program will be presented in a subsequent paper: Model atmosphere calculations which incorporate these rates into synthetic spectra.

T Kallman↗

NASA NTRS2022

Gas-Liquid Flows Through Porous Media in Microgravity: Packed Bed Reactor Experiment-2

Modifications were made to the Packed Bed Reactor Experiment (PBRE) and flown on the ISS as PBRE-2 to eliminate external pressure oscillations at higher liquid flow rates and the packing diameter was reduced to increase the pressure gradient for lower flows. It is found that gas hold-up is a function of bed history at low liquid and gas flow rates whereas higher gas hold-up and pressure gradients are observed for the test conditions following a liquid only pre-flow compared to the test conditions following a gas only pre-flow period. Over the range of flow rates tested, the capillary force is the dominant contributor to the pressure gradient, which is found to be linear with the superficial liquid velocity but is a much weaker function of the superficial gas velocity, and varying inversely with the particle diameter.

Mahsa Taghavi↗

NASA NTRSDate not supplied

A Study of the Swelling and Bursting of the High Pressure Coupling (HPC) of a Two-Stage Light Gas Gun

• Need for data at muzzle velocities of 7.0 km/s and above to simulate impacts of space debris and naturally occurring meteoroids • The two-stage light gas gun is a well known way of achieving these velocities • There is a danger of significant swelling and even bursting of the HPC (high pressure coupling). • A consistent picture of the swelling and bursting of the HPCs of two Ames two-stage light gas guns is developed, based on the following: 1. Experimental measurements of the swelling and bursting of the HPCs of two two-stage light gas guns. 2. Stress-strain calculations of the swelling and bursting of thick walled steel tubes. 3. Experimental measurements swelling and bursting of thick walled steel tubes. 4. CFD calculations of the maximum pressures in the HPC of a two-stage light gas gun using the code LGGUN. • It is shown that model developed predicts swelling and bursting that agrees reasonably well with measured data. • Hence, it is suggested that the model could be used in the design of a two-stage light gas guns to assess the risk of swelling and bursting and to give maximum suggested operating conditions for an existing gun.

Ballistic Range↗

NASA NTRS2022

Gulf of Mexico Health & Air Quality Ii: Mapping Methane Emission Plumes Using Sunglint-Configured Imagery for Monitoring Offshore Oil and Gas Activity

Offshore oil and gas production in the United States is a major source of anthropogenic greenhouse gas emissions and accounts for nearly 30% of global oil and gas production. Methane venting and flaring are primary contributors to offshore emissions, and monitoring these activities is crucial for mitigating greenhouse gas emissions. Limited ground truthing and intermittent offshore satellite revisits make monitoring venting and flaring challenging. The Bureau of Ocean Energy Management (BOEM) and the Bureau of Safety and Environmental Enforcement (BSEE) oversee offshore oil and gas activity but rely primarily on operator-reported data. The non-profit organization SkyTruth monitors natural resources like methane and identifies sources of fugitive emissions. By combining BOEM and BSEE’s operational data along with observations from Sentinel-2 Multispectral Instrument (MSI), Landsat 8 Operational Land Imager (OLI) and Landsat 9 OLI-2, and PRecursore IperSpettrale della Missione Applicativa (PRISMA), the team further identified ultra-emitter point sources in the Gulf of Mexico using sunglint-configured imagery. We quantified these plume emission rates using the methodology from Varon et al. (2020). The team found three plumes in the Gulf of Mexico occurring between 2020 and 2022 using Sentinel-2 MSI and Landsat 9 OLI-2 imagery, in addition to the single plume identified by the Gulf of Mexico Health & Air Quality I team, and successfully quantified three plumes. Our statistical retrieval of three PRISMA images tasked over areas of interest yielded no methane plumes, despite a successful test of a known plume in Assam, India. These analyses serve as a proof of concept for the utility of remote sensing for methane emission monitoring offshore, which can complement regulator emission inventories and validate self-reported operator records.

sunglint↗

NASA NTRS1966

Development of high pressure gas systems

This paper presents a report on the latest advances and technology in the design, construction, testing, and operation of high pressure gas bimetallic pipe systems and high pressure gas tube fittings facilitating greater alinement and manufacturing tolerances, and the supercleaning of high pressure gas systems under field conditions. The following specific topics are discussed: - Analysis of noncorrosive steels versus bimetallic, high strength steels - Analysis of various protective finishes versus bimetallic piping - Testing of high pressure systems - Pipe liner adhesion properties under varying operating conditions - Modified flared tube fittings taking into account pressure ranges, materials, costs involved in manufacture, various methods employed to permit sealing of the fitting while meeting cleanliness requirements - Cleaning requirements appertaining to high pressure gas systems and a discussion of investigations on the effects of velocity and temperature as related to various cleaning chemicals. The presentation concludes with a discussion on the possible applications of materials and methods in commercial industry.

Fitting↗

NASA NTRS2016

Practical Techniques for Modeling Gas Turbine Engine Performance

The cost and risk associated with the design and operation of gas turbine engine systems has led to an increasing dependence on mathematical models. In this paper, the fundamentals of engine simulation will be reviewed, an example performance analysis will be performed, and relationships useful for engine control system development will be highlighted. The focus will be on thermodynamic modeling utilizing techniques common in industry, such as: the Brayton cycle, component performance maps, map scaling, and design point criteria generation. In general, these topics will be viewed from the standpoint of an example turbojet engine model; however, demonstrated concepts may be adapted to other gas turbine systems, such as gas generators, marine engines, or high bypass aircraft engines. The purpose of this paper is to provide an example of gas turbine model generation and system performance analysis for educational uses, such as curriculum creation or student reference.

aerothermodynamics↗

NASA NTRS2016

Practical Techniques for Modeling Gas Turbine Engine Performance

The cost and risk associated with the design and operation of gas turbine engine systems has led to an increasing dependence on mathematical models. In this paper, the fundamentals of engine simulation will be reviewed, an example performance analysis will be performed, and relationships useful for engine control system development will be highlighted. The focus will be on thermodynamic modeling utilizing techniques common in industry, such as: the Brayton cycle, component performance maps, map scaling, and design point criteria generation. In general, these topics will be viewed from the standpoint of an example turbojet engine model; however, demonstrated concepts may be adapted to other gas turbine systems, such as gas generators, marine engines, or high bypass aircraft engines. The purpose of this paper is to provide an example of gas turbine model generation and system performance analysis for educational uses, such as curriculum creation or student reference.

aerothermodynamics↗

NASA NTRS2016

Exocometary Gas in the HD 181327 Debris Ring

An increasing number of observations have shown that gaseous debris discs are not an exception. However, until now, we only knew of cases around A stars. Here we present the first detection of 12CO (2-1) disc emission around an F star, HD 181327, obtained with the Atacama Large Millimeter/submillimeter Array (ALMA) observations at 1.3 mm. The continuum and CO emission are resolved into an axisymmetric disc with ring-like morphology. Using a Markov chain Monte Carlo method coupled with radiative transfer calculations, we study the dust and CO mass distribution. We find the dust is distributed in a ring with a radius of 86.0 +/- 0.4 au and a radial width of 23.2 +/- 1.0 au. At this frequency, the ring radius is smaller than in the optical, revealing grain size segregation expected due to radiation pressure. We also report on the detection of low-level continuum emission beyond the main ring out to approximately 200 au. We model the CO emission in the non-local thermodynamic equilibrium regime and we find that the CO is co-located with the dust, with a total CO gas mass ranging between 1.2 x 10(exp -6) solar mass and 2.9 x 10(exp -6) solar mass, depending on the gas kinetic temperature and collisional partners densities. The CO densities and location suggest a secondary origin, i.e. released from icy planetesimals in the ring. We derive a CO+CO2 cometary composition that is consistent with Solar system comets. Due to the low gas densities, it is unlikely that the gas is shaping the dust distribution.

exocometary gas↗

NASA NTRSDate not supplied

Considerations for the Extension of Gas Path Analysis to Electrified Aircraft Propulsion Systems

Aircraft operators rely on gas path analysis techniques for monitoring the performance and health of their gas turbine engine assets. This is accomplished by analyzing discernable shifts in measurement parameters acquired from the engine. This paper reviews the founding mathematical principles of gas path analysis, including conventional approaches applied for estimating engine performance deterioration. Considerations for extending the application of gas path analysis techniques to Electrified Aircraft Propulsion (EAP) systems is also discussed, and simulated results from their application to an EAP concept comprised of turbomachinery and electrical system hardware is provided. Results are provided comparing the parameter estimation accuracy offered by taking a whole-system approach towards the problem setup versus that offered by analyzing each subsystem individually. For the latter, the importance of having accurate direct or inferred measurements of external mechanical torque loads placed upon turbomachinery shafts is emphasized.

Electrified Aircraft Propulsion↗

NASA NTRS2021

Considerations for the Extension of Gas Path Analysis to Electrified Aircraft Propulsion Systems

Aircraft operators rely on gas path analysis techniques for monitoring the performance and health of their gas turbine engine assets. This is accomplished by analyzing discernable shifts in measurement parameters acquired from the engine. This paper reviews the founding mathematical principles of gas path analysis, including conventional approaches applied for estimating engine performance deterioration. Considerations for extending the application of gas path analysis techniques to Electrified Aircraft Propulsion (EAP) systems is also discussed, and simulated results from their application to an EAP concept comprised of turbomachinery and electrical system hardware is provided. Results are provided comparing the parameter estimation accuracy offered by taking a whole-system approach towards the problem setup versus that offered by analyzing each subsystem individually. For the latter, the importance of having accurate direct or inferred measurements of external mechanical torque loads placed upon turbomachinery shafts is emphasized.

Electrified Aircraft Propulsion↗

NASA NTRS2021

Considerations for the Extension of Gas Path Analysis to Electrified Aircraft Propulsion Systems

Aircraft operators rely on gas path analysis techniques for monitoring the performance and health of their gas turbine engine assets. This is accomplished by analyzing discernable shifts in measurement parameters acquired from the engine. This paper reviews the founding mathematical principles of gas path analysis, including conventional approaches applied for estimating engine performance deterioration. Considerations for extending the application of gas path analysis techniques to Electrified Aircraft Propulsion (EAP) systems is also discussed, and simulated results from their application to an EAP concept comprised of turbomachinery and electrical system hardware is provided. Results are provided comparing the parameter estimation accuracy offered by taking a whole-system approach towards the problem setup versus that offered by analyzing each subsystem individually. For the latter, the importance of having accurate direct or inferred measurements of external mechanical torque loads placed upon turbomachinery shafts is emphasized.

Electrified Aircraft Propulsion↗

NASA NTRSDate not supplied

Investigating Waste Preparation Methods for Trash-to-Gas Technologies

Trash-to-Gas technologies show promise in addressing the need for a proper waste management system onboard a long-duration space mission. However, there is a clear need to better understand how the initial waste preparation can affect the overall conversion efficiency. Factors such as the waste size, moisture content, and packing density can have significant impacts on the reactor performance. This paper will focus on the effects of various pre-processing steps on the overall solid-to-gas conversion on the state of the art Trash-to-Gas system developed at NASA Kennedy Space Center. These results will help inform future Trash-to-Gas technologies on what types of supporting subsystems will be necessary to operate effectively for exploration missions.

Trash to Gas↗

NASA NTRSDate not supplied

Investigating Waste Preparation Methods for Trash-to-Gas Technologies

Trash-to-Gas technologies show promise in addressing the need for a proper waste management system onboard a long-duration space mission. However, there is a clear need to better understand how the initial waste preparation can affect the overall conversion efficiency. Factors such as the waste size, moisture content, and packing density can have significant impacts on the reactor performance. This paper will focus on the effects of various pre-processing steps on the overall solid-to-gas conversion on the state of the art Trash-to-Gas system developed at NASA Kennedy Space Center. These results will help inform future Trash-to-Gas technologies on what types of supporting subsystems will be necessary to operate effectively for exploration missions.

Trash to Gas↗

NASA NTRS2023

Effect of the Electrostatic Field due to the Surface Monolayer Metal Atoms on the Dissociation of Homonuclear Diatomic Gases in Gas-Metal Surface Reactions

The present paper examines the role of an electrostatic field generated by the outermost monolayer of metal ions prior to gas adsorption in aiding the dissociation of homonuclear diatomic gas molecules. The interaction of five homonuclear diatomic gases, Cl 2 , F 2 , H 2 , N 2 and O 2 , with several pure metals are examined using Coulomb’s law to calculate the attractive and repulsive forces between the electrons or ions in the gas molecule and the free surface metallic electrons or ions assuming a Bohr model. These calculations demonstrate that the total energy of the electrostatic fields from the metals can exceed the molecular binding energies of Cl 2 , F 2 , and O 2 at some distance from the metallic surface thereby suggesting that these gases interact primarily with the metallic surface in their atomic states after molecular bond dissociation prior to reaction. In contrast, H 2 and N 2 gases do not dissociate prior to reaching the metal surface due to the fact that the effective charge of the gas ions is less than the total electron charge at the outermost electronic shell. The present results correlate linearly with the electrochemical series standard reduction potential as well as with the Pauling electronegativity for several metals.

Gas-metal reactions↗

NASA NTRS2023

Quantitative Gas Property Measurements By Filtered Rayleigh Scattering: A Review

Filtered Rayleigh scattering (FRS) is a laser-based diagnostic technique used to nonintrusively quantify various thermodynamic properties of a light-scattering gas. The backbone of FRS is the molecular filtering of Rayleigh scattered light. This concept was initially introduced by the atmospheric LIDAR community before being adopted within the aerospace research field in the early 1990s. Since then, FRS has matured into a versatile quantitative diagnostic tool and has found use in a variety of flow regimes ranging from sub- to supersonic speeds in both reacting and nonreacting environments. This adoption can be attributed to the wealth of information that can be obtained via FRS, including the gas density, pressure, temperature, velocity, species composition, or, in some cases, several of these properties at once. This article reviews the current state of FRS methodology in recovering such gas properties. As knowledge of the fundamentals of Rayleigh scattering and spectral light filtering is crucial to the design of an FRS experiment, we begin by briefly reviewing these areas. Subsequently, we conduct a survey of experimental design strategies, assumptions, and data reduction methods used to measure different gas properties using FRS. We conclude the review with a short discussion on quantification of experimental uncertainty and future trends in FRS.

filtered Rayleigh scattering↗

NASA NTRS2023

Automated Machine Learning to Evaluate the Information Content of Tropospheric Trace Gas Columns for Fine Particle Estimates Over India: A Modeling Testbed

India is largely devoid of high-quality and reliable on-the-ground measurements of fine particulate matter (PM 2.5 ). Ground-level PM 2.5 concentrations are estimated from publicly available satellite Aerosol Optical Depth (AOD) products combined with other information. Prior research has largely overlooked the possibility of gaining additional accuracy and insights into the sources of PM using satellite retrievals of tropospheric trace gas columns. We evaluate the information content of tropospheric trace gas columns for PM 2.5 estimates over India within a modeling testbed using an Automated Machine Learning (AutoML) approach, which selects from a menu of different machine learning tools based on the data set. We then quantify the relative information content of tropospheric trace gas columns, AOD, meteorological fields, and emissions for estimating PM 2.5 over four Indian sub-regions on daily and monthly time scales. Our findings suggest that, regardless of the specific machine learning model assumptions, incorporating trace gas modeled columns improves PM 2.5 estimates. We use the ranking scores produced from the AutoML algorithm and Spearman’s rank correlation to infer or link the possible relative importance of primary versus secondary sources of PM 2.5 as a first step toward estimating particle composition. Our comparison of AutoML-derived models to selected baseline machine learning models demonstrates that AutoML is at least as good as user-chosen models. The idealized pseudo-observations (chemical-transport model simulations) used in this work lay the groundwork for applying satellite retrievals of tropospheric trace gases to estimate fine particle concentrations in India and serve to illustrate the promise of AutoML applications in atmospheric and environmental research.

Machine learning↗

NASA NTRSDate not supplied

CFD Modeling of Tank Pressurization and Axial Jet Mixing Experiments with and without Non-Condensable Gas in the Ullage

A two-phase CFD model for tank pressurization and following jet mixing of a cryogenic storage tank is presented using VOF approach for representing the phase boundary and the associated interfacial heat, mass and momentum transfer between the liquid and vapor regions. The CFD model was validated against pressurization and liquid jet mixing data for a 110-inch diameter tank provided by Bullard1. Cases with like-gas and non-condensable gas pressurization are studied. The results of the cases with like-gas pressurization and following mixing are presented first, focusing on the effects of turbulence at the vapor-liquid interface on the tank pressure and phase change rates predictions. The second part of this paper is devoted to testing and validating the CFD model against non-condensable gas pressurization and following mixing. Tank pressures predicted in both cases are compared with each other and with the experimental data.

Computational Fluid Dynamics↗