Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FEET”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

The role of plasma wave turbulence in the formation of shock waves in collisionless plasmas

A data set containing measurements for approximately 100 shock crossings was compiled, and plasma wave profiles were plotted in conjunction with magnetic field data. Three emissions analyzed include upstream electron plasma oscillations, ion acoustic noise, and low frequency electromagnetic noise. The data demonstrate that the observed waves are consistent with generation by the kinetic cross-field streaming instability. Reanalysis of shock overshoots prompted by the presence of plasma feet upstream of nominally subcritical shocks leads to the conclusion that no firm evidence exists for a sharp subcritical supercritical transition. Electron plasma oscillations persist up to the ramps of subcritical shocks and begin decaying at the front edge of the feet of supercritical shocks. Their intensity is anticorrelated with the amplitude of the foot ion acoustic noise. Wave measurements support the predicted predominance of lower hybrid-like modes over ion acoustic noise in the production of resistive (plasma) heating. Evidence for variable shock normal angles is seen upstream from nominally quasiparallel shocks. The first cases of very strong electron heating observed at the terrestrial bow shock were discovered.

Mellott, M. M.↗

Wind tunnel test results of heavy rain effects on airfoil performance

The effects of simulated heavy rain on the aerodynamic characteristics of a NACA 64-210 airfoil section equipped with high-lift devices were investigated in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The experiment was part of an on-going NASA program to determine the effect of heavy rain on airplane performance, and was directed at providing insight into scaling laws for subscale model testing of rain effects. The model used in the investigation had a chord of 2.5 feet, a span of 8.0 feet, and was mounted on the tunnel centerline between two large endplates. A water spray distribution system was located 10 chord lengths upstream of the model. The sensitivity of test results to partial-span coverage of the model in the simulated rain environment as compared to full-span coverage was also investigated. The lift and drag data obtained for the high-lift configuration show excellent repeatability of results compared to the previous data. Results obtained for various spray concentrations and tunnel speeds showed significant losses in maximum lift capability, a decrease in the angle of attack for maximum lift, and an increase in drag as the stimulated rain rate was increased. The test results also indicated that the data were not strongly affected by surface tension effects for the high-lift configuration.

Bezos, G. M.↗

Validation of an interior noise prediction model for a composite cylinder

An acoustic modal analysis has been performed in the cavity of a composite cylinder model of an aircraft fuselage. The filament wound, composite shell is 12 feet long and 5.5 feet in diameter. A one-half-in. thick plywood floor is attached to the shell 69 deg from the vertical centerline through the bottom of the shell. The acoustic modal frequencies were obtained from a sound pressure level and phase survey conducted throughout the interior volume bounded by the floor, endcaps and stiffened shell, while being excited by white noise from a loudspeaker source. The measured acoustic resonance frequencies and mode shapes compare well with analytical predictions from the Propeller Aircraft Interior Noise (PAIN) model. Details of the theory and derivation of the acoustic characteristics have been included. Reverberation time measurements, using the integrated impulse technique, have been performed to determine acoustic loss factors. These measured loss factors have been input to the PAIN program in order to more accurately predict the space-averaged interior noise of the composite cylinder.

Beyer, Todd B.↗

Equilibrium and tearing stability of thin current layers in magnetic arcades

The MHD equilibrium of a thin, force-free current layer in a magnetic arcade is solved analytically. Various approximations are made in order to achieve a lowest order description that is physically relevant as well as mathematically tractable: The arcade is assumed to emanate from feet that are well localized, the current emanates from a localized sheet within the feet and is relatively weak. The resulting expressions for B (sup arrow) are relatively simple and natural flux coordinates are identifiable. The stability of such a current sheet to resistive filamentation is then investigated.

Hassam, A. B.↗

The impact of asymmetric physical properties on large space structures

The Space Station Reference Configuration is assembled in 19 assembly flights of several large structure elements of varied size and shape that contribute to its overall asymmetrical nature. The elements include thousands of square feet of solar arrays and thermal radiators, several hundred feet of truss structure, and several hundred thousand pounds of large-diameter cylindrical-shaped pressure modules housing scientific experiments and astronaut habitation areas. This paper quantitatively describes these physical characteristics of the fully assembled Space Station configuration. Several flight control design considerations are discussed relating to control system sizing, flight-path attitude orientation, payload pointing accommodation, and potential configuration modifications.

Deryder, L.↗

Tool Distributes Clamping Load

Tool distributes clamping load stably and fairly evenly among five clamping feet. Designed to stabilize and even out pressure applied to foam pads during bonding and also used in other situations where necessary to maintain fairly even clamping loads during fabrication processes. Five clamping feet, four of which adjustable, distribute clamping load and maintain clamping configuration during adhesive bonding or similar fabrication process. Used to clamp nonflat as well as flat surfaces.

Spencer, Barry Wayne↗

Noise of the Harrier in vertical landing and takeoff

The noise of the Harrier AV8C aircraft in vertical takeoff and landing was measured 100 feet to the side of the aircraft where jet noise dominates. The noise levels were quite high - up to 125 dB overall sound level at 100 feet. The increased noise due to jet impingement on the ground is presented as a function of jet height to diameter ratio. The impingement noise with the aircraft close to the ground was 14 to 17 dB greater than noise from a free jet. Results are compared with small-scale jet impingement data acquired elsewhere. The agreement between small-scale and full-scale noise increase in ground effect is fairly good except with the jet close to the ground. It is proposed that differences in the jet Reynolds numbers and the resultant character of the jets may be partially responsible for the disparity in the full-scale and small-scale jet impingement noise. The difference between single-jet impingement and multiple-jet impingement may also have been responsible for the small-scale and full-scale disagreement.

Soderman, Paul T.↗

CONDOR: Long endurance high altitude vehicle, volume 5

The results of a design study resulting in the proposed CONDOR aircraft are presented. The basic requirements are for the aircraft to maintain continuous altitude at or above 45,000 feet for at least a 3-day mission, be able to comfortably support a two-man crew during this period with their field of vision not obstructed to a significant degree, carry a payload of 200 pounds, and provide a power supply to the payload of 2000 watts. The take-off and landing distances must be below 5000. feet, and time to reach cruise altitude must not exceed 3 hours. The subjects discussed are configuration selection, structural analysis, stability and control, crew and payload accomodations, and economic estimates.

Andrews, L. Cullen↗

Thrust vectoring effect on time-optimal 90 degrees angle of attack pitch up maneuvers of a high alpha fighter aircraft

Using thrust vectoring, the problem of pitching up a high alpha fighter aircraft to 90 degrees angle of attack in minimum time is considered. Pontryagin's maximum principle is used together with a two-point boundary value numerical algorithm to derive open-loop controls for various parameterized limits on thrust vectoring angles. Without thrust vectoring, a high alpha fighter with initial conditions 0.6 Mach number and 15,000 feet requires 7.0 seconds to pitch-up to 90 degrees. However, with 20-degree angle thrust vectoring, the pitch-up takes only 1.5 seconds with a final Mach number of 0.47. Also, the gain in altitude is less than 100 feet. More important, additional thrust vectoring yields litle benefit beyond the 20-degree angles. This paper describes control solutions in detail for thrust vectoring angles between 0 and 90 degrees.

Stalford, Harold↗

Low Earth Orbit Raider (LER) winged air launch vehicle concept

The need to launch small payloads into low earth orbit has increased dramatically during the past several years. The Low Earth orbit Raider (LER) is an answer to this need. The LER is an air-launched, winged vehicle designed to carry a 1500 pound payload into a 250 nautical mile orbit. The LER is launched from the back of a 747-100B at 35,000 feet and a Mach number of 0.8. Three staged solid propellant motors offer safe ground and flight handling, reliable operation, and decreased fabrication cost. The wing provides lift for 747 separation and during the first stage burn. Also, aerodynamic controls are provided to simplify first stage maneuvers. The air-launch concept offers many advantages to the consumer compared to conventional methods. Launching at 35,000 feet lowers atmospheric drag and other loads on the vehicle considerably. Since the 747 is a mobile launch pad, flexibility in orbit selection and launch time is unparalleled. Even polar orbits are accessible with a decreased payload. Most importantly, the LER launch service can come to the customer, satellites and experiments need not be transported to ground based launch facilities. The LER is designed to offer increased consumer freedom at a lower cost over existing launch systems. Simplistic design emphasizing reliability at low cost allows for the light payloads of the LER.

Feaux, Karl↗

En route noise: NASA propfan test aircraft (calculated source noise

The second phase of a joint National Aeronautics and Space Administration (NASA) and Federal Aviation Administration (FAA) program to study the high-altitude, low-frequency acoustic noise propagation characteristics of the Advanced Turboprop (propfan) Aircraft was conducted on April 3-13, 1989 at the White Sands Missile Range (WSMR), New Mexico. The first phase was conducted on October 26-31, 1987 in Huntsville, Alabama. NASA (Lewis) measured the source noise of the test aircraft during both phases while NASA (Langley) measured surface noise only during the second phase. FAA/NASA designed a program to obtain noise level data from the propfan test bed aircraft, both in the near field and at ground level, during simulated en route flights (35,000 and 20,000 feet ASL), and to test low frequency atmospheric absorption algorithms and prediction technology to provide insight into the necessity for regulatory measures. The curves of calculated source noise versus emission angle are based on a second order best-fit curve of the peak envelope of the adjusted ground data. Centerline and sideline derived source noise levels are shown to be in good agreement. A comparison of the Alabama chase plane source data and the calculated source noise at centerline for both the Alabama and New Mexico data shows good agreement for the 35,000 and the 20,000 feet (ASL) overflights. With the availability of the New Mexico in-flight data, further in depth comparisons will be made.

Rickley, E. J.↗

Advanced recovery systems wind tunnel test report

Pioneer Aerospace Corporation (PAC) conducted parafoil wind tunnel testing in the NASA-Ames 80 by 120 test sections of the National Full-Scale Aerodynamic Complex, Moffett Field, CA. The investigation was conducted to determine the aerodynamic characteristics of two scale ram air wings in support of air drop testing and full scale development of Advanced Recovery Systems for the Next Generation Space Transportation System. Two models were tested during this investigation. Both the primary test article, a 1/9 geometric scale model with wing area of 1200 square feet and secondary test article, a 1/36 geometric scale model with wing area of 300 square feet, had an aspect ratio of 3. The test results show that both models were statically stable about a model reference point at angles of attack from 2 to 10 degrees. The maximum lift-drag ratio varied between 2.9 and 2.4 for increasing wing loading.

Geiger, R. H.↗

OVRhyp, Scramjet Test Aircraft

A preliminary design for an unmanned hypersonic research vehicle to test scramjet engines is presented. The aircraft will be launched from a carrier aircraft at an altitude of 40,000 feet at Mach 0.8. The vehicle will then accelerate to Mach 6 at an altitude of 100,000 feet. At this stage the prototype scramjet will be employed to accelerate the vehicle to Mach 10 and maintain Mach 10 flight for 2 minutes. The aircraft will then decelerate and safely land.

Aslan, J.↗

Winged cargo return vehicle conceptual design

NASA is committed to placing a permanent space station in Earth orbit in the 1990's. Space Station Freedom (SSF) will be located in a 220 n.m. orbit at 28.5 degrees inclination. The Winged Cargo Return Vehicle's (CRV) primary mission is to support SSF crew by flying regular resupply missions. The winged CRV is designed to be reusable, dry land recoverable, and unmanned. The CRV will be launched inline on three liquid hydrogen/oxygen rocket boosters with a payload capacity of 113,000 lbs. The three boosters will take the CRV to an orbit of 50 by 110 n.m. From this altitude the orbital manuevering engine will place the vehicle in synchronous orbit with the space station. The winged CRV will deliver cargo modules to the space station by direct docking or by remaining outside the SSF command zone and using the Orbital Maneuvering Vehicle (OMV) to transfer cargo. After unloading/loading, the CRV will deorbit and fly back to Kennedy Space Center. The CRV has a wing span of 57.8 feet, a length of 76.0 feet, and a dry weight of 61.5 klb. The cargo capacity of the vehicle is 44.4 klb. The vehicle has a lift-drag ratio of 1.28 (hypersonic) and 6.0 (subsonic), resulting in a 1351 n.m. cross range. The overall mission length ranges between 18.8 and 80.5 hr. The operational period will be the years 2000 to 2020.

Source record↗

High altitude reconnaissance aircraft

At the equator the ozone layer ranges from 65,000 to 130,000 plus feet, which is beyond the capabilities of the ER-2, NASA's current high altitude reconnaissance aircraft. The Universities Space Research Association, in cooperation with NASA, is sponsoring an undergraduate program which is geared to designing an aircraft that can study the ozone layer at the equator. This aircraft must be able to cruise at 130,000 feet for six hours at Mach 0.7, while carrying 3,000 lbs. of payload. In addition, the aircraft must have a minimum range of 6,000 miles. In consideration of the novel nature of this project, the pilot must be able to take control in the event of unforeseen difficulties. Three aircraft configurations were determined to be the most suitable - a joined-wing, a biplane, and a twin-boom conventional airplane. The performance of each configuration was analyzed to investigate the feasibility of the project.

Yazdo, Renee Anna↗

Carrier aircraft

The Ohio State University planned to conduct a conceptual design of a single research vehicle that could be used to explore the flight regime from Mach 6 to Mach 12. Since this aircraft will be a special purpose vehicle, it need not take off and land in a conventional manner. Indeed, if this aircraft were launched from a larger aircraft that carried it to altitude, then conventional landing gear would not be needed and the extra weight of the fuel needed to take off and climb into the stratosphere would be eliminated. The focus of the students' project was on the design of a carrier aircraft answering to the specifications. Its mission is to take off with the research aircraft from runways of less than 15,000 feet, climb to 40,000 feet, and release the hypersonic aircraft at the speed of Mach 8, and return to base. The range of this mission is 2000 n.m. This study includes the conception of an optimized aircraft (geometry, weights, propulsion, aerodynamics, interactions between the two aircraft, etc.), the longitudinal stability of the composite, and the separation critical phase.

Source record↗

NASA DC-8 airborne research laboratory

Since the summer of 1987, NASA Ames Research Center has been operating a DC-8 equipped with CFM 56 engines as a flying research laboratory. In this relatively short time, the DC-8, with its tremendous capabilities, has made significant contributions to numerous scientific fields. Capable of staying aloft for over 12 hours, the DC-8 has flown directly over both the North and South Poles, gathering data relating to the ozone hole. Operating from a few thousand feet to over 40,000 feet above sea level the interchangeable payload capability of the DC-8 has made it a versatile scientific tool. The DC-8 also plays a vital role in the development of new satellite-borne sensors as very often those sensors are test-flown on the DC-8 before they are launched into space. The tremendous range and instrument carrying capability make the DC-8 an ideal flying laboratory. A few of the programs the DC-8 has participated in as well as a sampling of the instruments carried are outlined.

Degreef, Leo H.↗

Postural responses of head and foot cutaneous microvascular flow and their sensitivity to bed rest

To explore the mechanism for facial puffiness, headache, and nasal congestion associated with microgravity and cephalad fluid shifts, the postural responses of the cutaneous microcirculation (CMC) in the forehead and dorsum of the foot of eight healthy men were studied by changing body position on a tilt table and measuring blood flows with a laser Doppler flowmeter. Increasing arterial pressure in the feet by moving from a -6-deg head-down tilt to a 60-deg head-up posture decreased foot CMC by 46.5 + or - 12.0 percent. Raising arterial pressure in the head increased forehead CMC by 25.5 + or - 0.7 percent (p less than 0.05). To investigate the possibility that these opposite responses could be modified by simulated microgravity, tilt test were repeated after 7 d of -6-deg head-down-tilt bed rest. The responses were not significantly different from those recorded before bed rest. Therefore, CMC in the feet is well regulated to prevent edema when shifting to an upright position, whereas there is less regulation in the head CMC.

Aratow, Michael↗