Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EUTECTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Metal Fuel Implications on Severe Accident Scenarios

Superior steady-state irradiation performance of metal fuel has been demonstrated, and metal fuel has been the choice for recent sodium-cooled fast reactor designs, e.g. PRISM, SAFR, 4S, TWR, PGSFR, and so on. Metal fuel also has excellent transient capabilities. The metal fuel itself does not impose any restrictions on transient operations or load-following capabilities. Metal fuel has benign run beyond cladding breach (RBCB) performance characteristics. Because metal fuel is compatible with sodium, there is no reaction product and the fuel loss is practically zero. Metal fuel is expected to be very reliable. However, even if unforeseen fuel pin failure occurs, it will simply release gases and does not cause failure propagation to neighboring pins. The eutectic formation temperature between the fuel and the cladding has been considered a critical parameter for the metal fuel pin design. The onset of fuel-cladding eutectic formation starts in the 700-725 deg. C temperature range, depending on the fuel alloy and cladding types. However, at this onset temperature, not much interaction occurs. In fact, even at 100 deg. C above the eutectic temperature, the eutectic penetration into the cladding is minimal in one hour. Only at much higher temperatures, close to the fuel melting point itself, the eutectic penetration into cladding becomes rapid. Therefore, the eutectic formation is not a primary safety concern during transient overpower conditions. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Significantly Promoting the Thermal Conductivity and Machinability of Negative Thermal Expansion Alloy via In Situ Precipitation of Copper Networks

Rapid advancements in electronic devices yield an urgent demand for high-performance electronic packaging materials with high thermal conductivity, low thermal expansion, and great mechanical properties. However, it is a great challenge for current design philosophies to fulfill all the requirements simultaneously. Here, an effective strategy is proposed for significantly promoting the thermal conductivity and machinability of negative thermal expansion alloy (Zr,Nb)Fe 2 through eutectic precipitation of copper networks. The eutectic dual-phase alloy exhibits an isotropic chips-matched thermal expansion coefficient and a thermal conductivity enhancement exceeding 200% compared with (Zr,Nb)Fe 2 , along with an ultimate compressive strength of 550 MPa. The addition of copper reorganizes the composition of (Zr,Nb)Fe 2 , which smooths the magnetic transition and shifts it toward higher temperature, resulting in linear low thermal expansion in a wide temperature range. The highly fine eutectic copper lamellae construct high thermal conductivity networks within (Zr,Nb)Fe 2 , serving as highways for heat transfer electrons and phonons. The in situ forming of eutectic copper lamellae also facilitates the mechanical properties by enhancing interfacial bonding and bearing additional stress after yielding of (Zr,Nb)Fe 2 . This work provides a novel strategy for promoting thermal conductivity and mechanical properties of negative thermal expansion alloys via eutectic precipitation of copper networks.

36 MATERIALS SCIENCE↗

The Binary Alkali Nitrate and Chloride Phase Diagrams: NaNO{sub 3}-KNO{sub 3}, LiNO{sub 3}-NaNO{sub 3}, LiNO{sub 3}-KNO{sub 3}, and NaCl-KCl

LiNO{sub 3}-NaNO{sub 3}, LiNO{sub 3}-KNO{sub 3,} NaNO{sub 3}-KNO{sub 3}, and NaCl-KCl phase relations were formulated using the regular solution model to obtain desired compositions for their potential application as a heat transfer fluid. The simultaneous nonlinear equations formed were solved numerically using a contour plot technique in Matlab. An algorithm was developed to determine the real roots of the coupled nonlinear equations and subsequent phase diagrams were constructed. The phase diagrams were compared with those predicted using FactSage thermochemical package and literature data from experimental studies. The calculated NaNO{sub 3}-KNO{sub 3} phase diagram shows that this system has a eutectic point at 0.5 mole fraction of KNO{sub 3} with a eutectic temperature of 220.85 °C, while the LiNO{sub 3}-KNO{sub 3} system was found to have a eutectic point at 0.44 mole fraction LiNO{sub 3} at 137 °C. The LiNO{sub 3}-NaNO{sub 3} system shows a eutectic at 0.524 mole fraction LiNO{sub 3} at 192.8 °C, and finally the NaCl-KCl system has a eutectic point at 0.48 mole fraction NaCl at 634 °C. The liquidus and solidus curves obtained fitted close against values obtained from the quasi-chemical model used in FactSage and experimental values from the literature. This study showed that the regular solution model combined with the contour plots approach can sufficiently describe the liquidus–solidus curves of the alkali binary nitrate and chloride systems and could be a useful method for predicting the phase diagrams for higher order alkali nitrates and chlorides.

36 MATERIALS SCIENCE↗

Influence of the Composition on the Solidification Path, Microstructure Evolution and Mechanical Properties of Al-Cu-Mg Alloys

The influence of the initial composition on the solidification path, microstructure evolution, thermophysical properties and mechanical properties of Al-Cu-Mg alloys was investigated. The solidification paths of the investigated alloys were determined by analyzing the solidification structure, and then the experimentally determined paths were compared with those from the calculated results. Three of the investigated alloys experienced typical ternary eutectic solidification, and the other four alloys experienced quasiperitectic reactions. Due to differences in the initial compositions, different eutectic morphologies were formed during the solidification process. The binary eutectic phases, (α-Al + Al{sub 2}Cu) and (α-Al + Al{sub 6}CuMg{sub 4}), and the (α-Al + Al{sub 6}CuMg{sub 4} + Al{sub 8}Mg{sub 5}) ternary eutectic phase tended to exhibit divorced growth, and the (α-Al + Al{sub 2}CuMg), (α-Al + Al{sub 6}CuMg{sub 4}) and (α-Al + Al{sub 2}Cu + Al{sub 2}CuMg) eutectic phases tended to exhibit coupled growth. The results indicated that the initial composition, solidification path, microstructure and morphology could greatly affect the melting enthalpy, microhardness and compressive strength of the investigated Al-Cu-Mg alloys.

36 MATERIALS SCIENCE↗

Deformation Behavior of Pure Copper Castings with As-Cast Surfaces for Electrical Parts

Herein, the tensile deformation behavior of pure copper castings with as-cast surfaces was investigated. It was found that small and sufficiently large uniform elongation types corresponded, respectively, to the presence or absence of a Cu-Cu{sub 2}O eutectic phase in the microstructure. Fissure defects were observed near the as-cast surfaces when the eutectic phase was present, probably leading to stress concentration. On the other hand, surface pinholes were observed when the eutectic phase was absent, and these were not prevented by directional solidification. Although the as-cast specimens (non-directionally solidified) exhibited a slightly reduced uniform elongation compared to the machined specimens in the absence of the eutectic phase, the directionally solidified as-cast samples exhibited a uniform elongation that was similar to that of the machined specimens. In addition, micropore arrays were formed along the grain boundaries inside the castings when the eutectic phase was absent, whereas almost no micropores were observed inside the directionally solidified as-cast specimens because the solidification process involved a faster cooling rate and/or higher temperature gradient. These results do not only suggest the existence of surface pinholes but also indicate that microporosity can reduce the cross-sectional area of the specimens, thus, affecting their uniform elongation.

36 MATERIALS SCIENCE↗

The microstructure and composition of equilibrium phases formed in hypoeutectic Te-In alloy during solidification

As a key tellurium atoms evaporation source for ultraviolet detection photocathode, the hypoeutectic Te{sub 75}In{sub 25} alloy was prepared by employing a slow solidification speed of about 10{sup −2} K/s. The microstructure and chemical composition of the equilibrium phases formed in the as-prepared alloy were studied in this research work. The experimental results show that the as-prepared Te-In alloy was constituted by primary In{sub 2}Te{sub 5} phase and eutectic In{sub 2}Te{sub 5}/Te phases. The eutectic In{sub 2}Te{sub 5}/Te phases are distributed in the grain boundaries of primary In{sub 2}Te{sub 5} phase. With the slow solidification speed, a pure eutectic Te phase without any excessive indium solute was obtained, where Te content of eutectic Te phase is 100 mass%. Moreover, it can be considered that the stress between the In{sub 2}Te{sub 5} and Te phases plays an important role in reducing the tellurium vapor pressure in Te{sub 75}In{sub 25} alloy. - Highlights: • The microstructure of Te-In alloy as an evaporation source was analyzed. • A pure eutectic Te phase was obtained by using a slow solidification speed method. • The relation between vapor pressure and inner-stress in the alloy was discussed.

36 MATERIALS SCIENCE↗

Effects of boron addition on the morphology of silicon phases in Al-Si casting alloys

Highlights: • The influence of boron on Si phase was studied. • Boron addition reduces the length of eutectic Si plates in Al-11Si alloys. • Boron addition promotes the nucleation temperature of primary Si phases in Al-14Si alloys. • Boron addition increases the twin density in the <112>{sub Si} growth direction of eutectic Si in Al-11Si and Al-14Si alloys. - Abstract: The influence of B elements on the morphology of Si phases in Al-11Si and Al-14Si alloys has been investigated employing Optical Microscope, Scanning Electron Microscopy, Transmission Electron Microscopy and Differential Scanning Calorimetry. In Al-11Si alloy, the addition of B element not only refines the primary Al dendrites, but also reduces the length of eutectic Si plates. In Al-14Si alloys, the addition of B element promotes the nucleation temperature of primary Si phases, but shows weak influence on the nucleation temperature of eutectics. The effects of B element on the morphologies of both primary Si particle and eutectics can be attributed to the interaction between B and Si elements during the solidification process.

36 MATERIALS SCIENCE↗

Interdiffusion Behavior of U{sub 3}Si{sub 2} and FeCrAl via Diffusion Couple Studies

Uranium Silicide (U{sub 3}Si{sub 2}) is in use as a dispersion plate fuel in test reactors, but has not been fully tested in light water reactor (LWR) conditions. U{sub 3}Si{sub 2} pellets have been fabricated for use in commercial LWRs as part of an accident tolerant fuel system U{sub 3}Si{sub 2} has a higher uranium loading density as well as a higher thermal conductivity relative to UO{sub 2}. FeCrAl alloy is a candidate cladding material to replace the industry standard, Zircaloy. FeCrAl has outstanding high-temperature mechanical strength and oxidation resistance under accident conditions. The U{sub 3}Si{sub 2}-FeCrAl system is expected to provide more than double the amount of time from a Scram until failure criteria for the reactor is met, as well as producing roughly half the amount of H{sub 2} in the event of a loss of coolant accident (LOCA). Uranium and iron have well know eutectics that may affect/enhance diffusion of the U{sub 3}Si{sub 2}/FeCrAl fuel system. The interaction of iron with molten uranium has been investigated In the U-Fe system, UFe{sub 2}, which melts congruently at 1235 deg. C, forms a eutectic with iron that melts at 1080 deg. C and has a composition of U-77at% Fe. UFe{sub 2} also forms a eutectic with uranium that melts at 725 deg. C and has a composition of U-34at% Fe. The U-34at% Fe eutectic extended the temperature range down to 740 deg. C. Regular operating temperatures for U{sub 3}Si{sub 2} fuel is expected to be around 300 - 400 deg. C. The eutectics of iron and uranium would nominally only be of concern in accident scenarios.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure and strengthening of Al-6Ce-3Ni-0.7Fe (wt%) alloy manufactured by laser powder-bed fusion

In this study, an Al-6Ce-3Ni-0.7Fe (wt%) alloy was fabricated via laser powder-bed fusion and its microstructure, thermal stability, tensile properties, and creep properties are investigated for two rapid-solidification rates with different eutectic spacings. For both faster- and slower-cooled states, the as-fabricated alloy mostly shows elongated grains with very fine eutectic networks (~40 nm lamellar width) comprising a high-volume fraction (~18 %) of intermetallic phases. Faster-cooled samples, however, display a less continuous eutectic network with finer spacing (~100 nm), leading to higher Orowan strengthening and therefore superior microhardness and yield stress up to ~350 °C. Upon aging (300 - 450 °C), micron-size Al 9 (Ni,Fe) 2 needle-like precipitates form within grains, and the Al 11 Ce 3 eutectic network spheroidizes, while retaining a submicron width and spacing, resulting in 33–37 % drop in microhardness after 144 h aging at 400 °C. Limited tensile ductility (~6 %) and creep ductility (~1-2 %) are measured for both faster- and slower-cooled alloys due to an inhomogeneous microstructure, where cavitation preferentially initiates at melt-pool boundaries, precipitate-free zones, and/or denuded zones, eventually leading to local fracture. Denuded zones, induced by stress, form due to diffusional flow with stress-dependent orientations, and are identified as microstructurally weak regions leading to strain localization. The present alloy does not show a significant difference in 300 °C creep resistance between: (i) tensile and compressive loading, (ii) faster- and slower-cooled samples, and (iii) continuous and spheroidized eutectics. Creep resistance at 300 °C is comparable to that of a Ce-richer Al-10.5Ce-3.1Ni-1.2Mn (wt%) alloy, despite the formation of denuded zones and needle-like Al 9 (Ni,Fe) 2 precipitates.

36 MATERIALS SCIENCE↗

Determination of a surrogate for plutonium electrorefining

Conducting research experiments on plutonium electrorefining is difficult due to the significant hazards and regulations associated with nuclear materials. Finding a surrogate for plutonium electrorefining studies would enable more fundamental research to be conducted. Potential surrogates were first identified by determining the physical properties required to conduct electrorefining at the same conditions commonly used in plutonium electrorefining, a molten metal and molten CaCl 2 at 1123 K. Ce-CeCl 3 , In-InCl 3 , and Pb-PbCl 2 were the only potential surrogates identified using these constraints. Sn-SnCl 2 was also tested at these same conditions. More potential surrogates were identified by changing the matrix salt and operating temperature. This expanded the potential surrogate list to also include Zn-ZnCl 2 , Sn-SnCl 2 , and Bi-BiCl 3 . Zn-ZnCl 2 was used with the LiCl-CaCl 2 (65:35 mol%) eutectic at 773 K. Sn-SnCl2 and Bi-BiCl 3 were used with the LiCl-KCl-CaCl 2 (50.5:44.2:5.3 mol%) eutectic at 673–773 K. Ce electrorefining in molten CaCl 2 resulted in a difficult to separate colloid mixture of Ce, Ca and Cl. Electrorefining rates for In in molten CaCl 2 were too slow due to InCl 3 volatilizing out of the molten salt. Only trace amounts of SnCl 2 was retained in the CaCl 2 at 1123 K resulting in impractical electrorefining rates. Zn metal product was successfully collected in the LiCl-CaCl 2 eutectic molten salt, but the metal obtained did not coalesce into one piece. Sn and Bi were successfully electrorefined in the LiCl-KCl-CaCl 2 eutectic molten salt and coalesced into product rings with high yields and coulombic efficiencies. Finally, while a surrogate could not be identified using the same conditions as plutonium electrorefining, two possible surrogates, Sn-SnCl 2 and Bi-BiCl 3 , were found that could imitate the physical configuration (i.e., molten salt on top of molten metal) of plutonium electrorefining at a reduced temperature using the eutectic LiCl-KCl-CaCl 2 salt at 673–773 K in place of CaCl 2 at 1123 K.

36 MATERIALS SCIENCE↗

Analysis and Thermal Property Investigations into Ternary Actinide Chloride Salt Systems Containing UCl3 and PuCl3

While regulators, the scientific community, and MSR developers still lack access to literature data on the thermal properties of clean fuel salts, even less information is available on the properties of fuel salts containing impurities. It is essential to understand, benchmark, and predict crucial data on the changes in thermal properties of fuel salt systems due to impurities arising from moisture, corrosion, and reactor operation (i.e., fission products). This research focuses on two actinide fuel salts (1) to investigate a worst-case scenario buildup of actinide fission product in a NaCl-UCl3 eutectic fuel salt and (2) to investigate NaCl-PuCl3 eutectic salt after 1000 hours of operation in a natural circulation flow loop flow to determine if corrosion or atmospheric (moisture/oxygen) products are present. For the first salt, a conservative assumption or worst-case scenario, for fission product buildup in a fuel salt was investigated by adding PuCl3 to eutectic 67 mol% NaCl – 33 mol% UCl3 salt resulting in a ternary salt having a composition of 61 mol% NaCl – 30 mol% UCl3 – 9mol% PuCl3. Addition of PuCl3 to eutectic NaCl-UCl3 resulted in a ternary salt that had a higher melting temperature than either the NaCl-PuCl3 or NaCl-UCl3 binary eutectic mixture. Addition of PuCl3 also resulted in an increase in density which was expected. The second salt was extracted from a micro loop. The composition of the fuel (primary) salt prior to flow loop operations was determined to be 64 mol% NaCl – 36 mol% PuCl3, however, the post-flow loop salt showed increased levels of MgCl2 and NaCl changing the salt composition to 10 mol% MgCl2 – 63mol% NaCl – 26mol% PuCl3) indicating the primary salt interacted with the rinse salt. Analysis of the post flow loop salt detected low concentrations of Al, Ni, Co, Nb, and Zr, most likely corrosion products from the flow loop material of construction. Contamination of the fuel salt (with the rinse salt NaCl-MgCl2) decreased the density by approximately 10% and reduced the onset of melting temperature by 50 °C, from 451 °C to approximately 400 °C. Results from the fission product simulated salt (61 mol% NaCl – 30 mol% UCl3 – 9mol% PuCl3) and the corrosion product salt (10 mol% MgCl2 – 63mol% NaCl – 26mol% PuCl3) will be included in two separate manuscripts for submission to peer-reviewed journals.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Size Distribution of Graphite Nodules in Hypereutectic Cast Irons of Varying Nodularity

An SGI was machined into 400 g cylindrical pieces and remelted in an electrical resistance furnace protected by Ar gas to produce materials ranging from SGI to CGI. The graphite morphology was controlled by varying the holding time at 1723 K (1450 °C) between 10 and 60 minutes. The discrete sectional size distribution of nodules by number density was measured on cross sections of the specimens and translated to volumetric distribution by volume fraction. Subpopulations of nodules were distinguished by fitting Gaussian distribution functions to the measured distribution. Primary and eutectic graphite, were found to account for most of the volume of nodular graphite in all cases. For holding times of 40 minutes and greater, corresponding to nodularity roughly below 40 pct, the primary subpopulation was very small and difficult to distinguish, leaving eutectic nodules as the dominant subpopulation. The mode and standard deviation of the two subpopulations were roughly independent of nodularity. Moreover, the nodular and vermicular graphite were segregated in the microstructure. In conclusion, the results suggest that the parallel development of the vermicular eutectic had small influence on the size distribution of eutectic graphite nodules.

36 MATERIALS SCIENCE↗

Microstructure and Wear Performance of Cobalt-Containing Iron-Based Slag-Free Self-shielded Flux-Cored Wire

A new type of cobalt-containing iron-based slag-free self-shielded flux-cored wire was developed for hardfacing. The influence of cobalt additions on the microstructure and wear performance of the hardfacing was investigated. The cobalt-containing iron-based hardfacing alloy has a typical hypereutectic microstructure consisting of primary M{sub 7}(C, B){sub 3} carbide, and a eutectic of M{sub 3}(C, B) carbide and austenite (part of which subsequently transformed into martensite). Cobalt promoted the formation of austenite and changed the morphology of the primary carbide and eutectic colonies. The morphology of primary carbide became fragmented with increasing cobalt due to the possible impeding effect of cobalt to the movement of the M{sub 7}(C, B){sub 3}/liquid interface. Different structures of the eutectic carbides were observed—the chrysanthemum structure for 1.42 wt.% cobalt, the skeleton form for 2.88 wt.% cobalt, the radial stripe 4.37 wt.% cobalt and the discrete stripe for 5.75 wt.% cobalt. Wear loss of the hardfacing alloy containing 2.88 wt.% cobalt was the smallest among all the alloys, owing to the large primary large carbide and skeleton-shaped eutectic carbides, the proper amount of austenite phase separating the M{sub 7}(C, B){sub 3} and M{sub 3}(C, B) carbides, the solid solution strengthening by cobalt in the matrix, and the high hardness of the alloy. Moreover, the wear resistance has a tendency to decrease with the increase in velocity as well as load.

36 MATERIALS SCIENCE↗

Development of iron phosphate ceramic waste form to immobilize radioactive waste solution

The objective of this research was to develop an iron phosphate ceramic (IPC) waste form using converter slag obtained as a by-product of the steel industry as a source of iron instead of conventional iron oxide. Both synthetic off-gas scrubber solution containing technetium-99 (or Re as a surrogate) and LiCl-KCl eutectic salt, a final waste solution from pyrochemical processing of spent nuclear fuel, were used as radioactive waste streams. The IPC waste form was characterized for compressive strength, reduction capacity, chemical durability, and contaminant leachability. Compressive strengths of the IPC waste form prepared with different types of waste solutions were 16 MPa and 19 MPa for LiCl-KCl eutectic salt and the off-gas scrubber simulant, respectively, which meet the minimum compressive strength of 3.45 MPa (500 psi) for waste forms to be accepted into the radioactive waste repository. The reduction capacity of converter slag, a main dry ingredient used to prepare the IPC waste form, was 4,136 meq/kg by the Ce(IV) method, which is much higher than those of the conventional Fe oxides used for the IPC waste form and the blast furnace slag materials. Average leachability indexes of Tc, Li, and K for the IPC waste form were higher than 6.0, and the IPC waste form demonstrated stable durability even after 63-day leaching. In addition, the Toxicity Characteristic Leach Procedure measurements of converter slag and the IPC waste form with LiCl-KCl eutectic salt met the universal treatment standard of the leachability limit for metals regulated by the Resource Conservation and Recovery Act. This study confirms the possibility of development of the IPC waste form using converter slag, showing its immobilization capability for radionuclides in both LiCl-KCl eutectic salt and off-gas scrubber solutions with significant cost savings.

converter slag↗

Microstructural evolution during transient liquid phase bonding of Inconel 738LC using AMS 4777 filler alloy

IN-738LC nickel-based superalloy was joined by transient liquid phase diffusion bonding using AMS 4777 filler alloy. The bonding process was carried out at 1050 Degree-Sign C under vacuum atmosphere for various hold times. Microstructures of the joints were studied by optical and scanning electron microscopy. Continuous centerline eutectic phases, characterized as nickel-rich boride, chromium-rich boride and nickel-rich silicide were observed at the bonds with incomplete isothermal solidification. In addition to the centerline eutectic products, precipitation of boron-rich particles was observed in the diffusion affected zone. The results showed that, as the bonding time was increased to 75 min, the width of the eutectic zone was completely removed and the joint was isothermally solidified. Homogenization of isothermally solidified joints at 1120 Degree-Sign C for 300 min resulted in the elimination of intermetallic phases formed at the diffusion affected zone and the formation of significant {gamma} Prime precipitates in the joint region. - Highlights: Black-Right-Pointing-Pointer TLP bonding of IN-738LC superalloy was performed using AMS 4777 filler alloy. Black-Right-Pointing-Pointer Insufficient diffusion time resulted in the formation of eutectic product. Black-Right-Pointing-Pointer Precipitation of B-rich particles was observed within the DAZ. Black-Right-Pointing-Pointer The extent of isothermal solidification increased with increasing holding time. Black-Right-Pointing-Pointer Homogenizing of joints resulted in the dissolution of DAZ intermetallics.

36 MATERIALS SCIENCE↗

Characterization of ZnAl cast alloys with Na addition

This study was aimed at evaluating the microstructural change and thermal, electrical and mechanical properties with the addition of Na to eutectic ZnAl alloys. Solders based on eutectic ZnAl containing 0.2 to 3.0 (wt.%) of Na were developed for high temperature solder. Differential scanning calorimetry (DSC) measurements were performed to determine the melting temperatures of the alloys. Thermal linear expansion and electrical resistivity measurements were performed over − 50 °C to 300 °C and 30 °C to 300 °C temperature ranges, respectively. The microstructure of the specimens was analyzed using scanning (SEM) and transmission electron microscopy (TEM) techniques. Chemical microanalysis was performed by energy-dispersive X-ray spectroscopy (EDS) on SEM and TEM. The precipitates of NaZn{sub 13} were confirmed by X-ray diffraction (XRD) measurements and selected area electron diffraction (SAED) techniques. The addition of Na to eutectic ZnAl alloy increased the electrical resistivity and reduced the coefficient of thermal expansion; however, the melting point did not change. The mechanical properties, strain and microhardness increased with Na content in alloys. - Highlights: • High temperature soldering materials of ZnAl with Na were designed and characterized. • Precipitates of NaZn{sub 13}were observed and confirmed using TEM and XRD. • Addition of Na to eutectic ZnAl cussed increased mechanical properties. • NaZn{sub 13} caused increased electrical resistivity and microhardness, and reduced the CTE.

36 MATERIALS SCIENCE↗

Correlative characterization of primary particles formed in as-cast Al-Mg alloy containing a high level of Sc

Primary particles formed in as-cast Al-5Mg-0.6Sc alloy and their role in microstructure and mechanical properties of the alloy were investigated using optical microscopy (OM), scanning electron microscopy (SEM), electron back-scatter diffraction (EBSD) and tensile testing. It was found that primary particles due to a close orientation to matrix could serve as the potent heterogeneous nucleation sites for α-Al during solidification and thus impose a remarkable grain refinement effect. Eutectic structure consisted of layer by layer of ‘Al{sub 3}Sc + α-Al + Al{sub 3}Sc + ⋯’ and cellular-dendritic substructure were simultaneously observed at the particles inside, indicating that these particles could be identified as the eutectics rather than individual Al{sub 3}Sc phase. A calculating method, based on EBSD results, was introduced for the spatial distribution of these particles in matrix. The results showed that these eutectic particles randomly distributed in matrix. In addition, the formation of primary eutectic particles significant improved the strength of the Al-Mg alloy in as-cast condition, which is ascribed to the structural evolution from coarse dendrites to prefect fine equiaxed grains. On the other hand, these large-sized particles due to the tendency to act as the microcrack sources could cause a harmful effect in the ductility of Al-Mg-Sc alloy. - Highlights: •Primary particles exhibit an ‘Al{sub 3}Sc + α-Al + Al{sub 3}Sc + ⋯’ multilayer feature with a cellular-dendritic mode of growth. •EBSD analyses the mechanism of grain refinement and the distribution of primary particles in α-Al matrix. •A computational method was presented to calculate the habit planes of primary particles.

36 MATERIALS SCIENCE↗

Evolution of carbide precipitates in Hastelloy N joints during welding and post weld heat treatment

Highlights: • The formation and spheroidization of the eutectic-like carbides are found in the Hastelloy N alloy during welding and PWHT. • All precipitates in the joints before and after the PWHT are identified as a M{sub 6}C type carbide with different morphology. • The diffusion of main element of Mo leads to the decrease of lattice parameter of the carbide during the welding and PWHT. - Abstract: The effects of welding and post weld heat treatment (PWHT) on the morphology, composition and lattice parameter of the precipitates in the welding joints of Hastelloy N alloy have been investigated. Joint samples were prepared using a gas tungsten arc welding process with ERNiMo-2 fillers, and then solid-solution treated at 1100 °C for 20 min. After welding, eutectic M{sub 6}C carbides can be observed in the heat affected zones (HAZ) and weld zones (WZ). These eutectic M{sub 6}C carbides become spheroidized during the following PWHT. The concentration of Si decreases during the transformation from the primary ones to eutectic ones, and then increases during the spheroidizing process. The total concentration of Si + Cr in M{sub 6}C carbides remains stable during welding and PWHT. At the same time, the heat leads to the outward diffusion of Mo from the M{sub 6}C carbides, which results in a decrease of the lattice parameter.

36 MATERIALS SCIENCE↗