Results for “CO formation” — Page 29

DOE OSTI2026

Characterization of γ′/γ″ compact and sandwich type precipitates during long-term high-temperature exposure in Ni-based superalloys

Here, the formation of γ′/γ″ co-precipitates is investigated in Ni-based superalloys with a varying Ti/Al ratio and Ta content and their stability is studied using long-term high-temperature exposure. Transmission electron microscopy and atom probe tomography analyses demonstrate that both higher Ti/Al ratios and increased Ta promote γ″ phase formation, leading to sandwich and compact structures. The compact co-precipitation significantly reduces γ′ precipitate coarsening during 10,000 h exposure at 700°C by restricting elemental diffusion, particularly of aluminum, from the γ matrix to the γ′ phase. For the alloy without a compact structure, and only γʹ precipitates, at the beginning of the exposure, the coarsening rate over 10,000 h was 3.5 times faster than for the alloy with compact γʹ/γʺ precipitates. Evidence of destabilization of the compact morphology was found to occur between 5,000 and 10,000 h exposure and originated from the extensive formation and growth of δ platelets that extended throughout the grains. Thus, the outer layer of the compact, which consists of γʺ, was subjected to the γ″ to δ phase transformation.

gamma double prime↗

DOE OSTI2021

Unimolecular and bimolecular formic acid decomposition routes on dispersed Cu nanoparticles

The elementary steps and site requirements in formic acid (HCOOH) dehydrogenation on Cu surfaces remain of keen interest because formate species act as intermediates or spectators in methanol synthesis and water–gas shift reactions. Steady-state and transient kinetic data, isotopic effects, infrared spectra during catalytic and stoichiometric reactions, and theoretical treatments based on density functional theory (DFT) provide evidence for bimolecular reactions, in which saturated bidentate formate (*HCOO*) adlayers, present at 0.25 ML (0.25 *HCOO* per surface Cu atom), react with undissociated species (HCOOH$^\square$) bound at interstices within formate adlayers ($^\square$) to form H-bonded bimolecular HCOOH$^\square$-*HCOO* adducts. The co-existence of vicinal HCOOH$^\square$ and *HCOO* moieties is evident from antisymmetric infrared bands for *HCOO* that become stronger as a result of their H-bonding that perturbs the induced dipole moment of *HCOO* upon vibration, consistent with DFT-derived vibrational frequencies and intensities for such perturbed species. The *HCOO* moiety in this complex undergoes C-H activation via a transition state that is preferentially stabilized through H-bonding with the vicinal HCOOH$^\square$ relative to its *HCOO* precursor. DFT-derived HCOOH dehydrogenation activation barriers and those determined from the evolution of CO 2 from pre-adsorbed *HCOO* species are about 10 kJ mol -1 smaller in the presence of gaseous HCOOH reactants (because of HCOOH$^\square$-*HCOO* interactions) than those for the unimolecular decomposition of bound *HCOO* species. Such bimolecular routes are consistent with measured effects of HCOOH, H 2 , and CO pressures and of H/D isotopic substitution on dehydrogenation turnover rates and represent the predominant channel for the formation of CO 2 and H 2 during catalytic HCOOH dehydrogenation on Cu nanoparticles. A saturated *HCOO* adlayer that retains binding interstices and the presence of HCOOH(g) enable a sequence of elementary steps unavailable for *HCOO* species, thus circumventing unassisted unimolecular routes that exhibit higher activation barriers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Highly durable fuel cell electrocatalyst with low-loading Pt-Co nanoparticles dispersed over single-atom Pt-Co-N-Graphene nanofiber

The limited durability of Pt electrocatalysis toward cathodic oxygen reduction reaction remains challenging, yet crucial for the development of Proton Exchange Membrane Fuel Cell. Here, we present a rational design of a robust catalyst consisting of PtCo nanoparticles supported on Pt-Co-N-graphene nanofiber prepared through electrospun Cobalt-Metal-Organic-Framework. The catalyst delivers unprecedented mass activity of 2.48 A·mgPt -1 , and retains 80% of initial value after 60,000 Accelerated-Stress-Test cycles. Operando X-ray absorption spectroscopies show that the electronic configurations of Pt sites in PtCo and Co sites in Co-N4 in the hybrid catalyst are modified toward high catalytic activities. Density Functional Theory unveils that the enhanced curvature of the substrate induced by the morphology engineering lowers the reaction thermodynamic barrier on Co-N4 sites, favoring the formation of H2O and suppressing that of H2O2. This result along with the strong affinity of PtCo nanoparticles to the Pt-Co-N-graphene fiber endows the catalyst an exceptional durability.

acidic electrolyte↗

DOE OSTI2025

The CO2 mineralization potential of New Mexico basalts and associated critical element behavior and mobility.

This presentation reports on laboratory experiments assessing the carbon dioxide (CO₂) mineralization potential of New Mexico basalts, including trachybasalt and basalt lithologies. Using simulated groundwater and controlled conditions, the study evaluates the kinetics of CO₂ sequestration, mineral saturation indices, and secondary mineral formation. It also investigates the mobility of critical and trace elements such as Ni, Zn, Cu, and Li during basalt dissolution. Results indicate that New Mexico basalts can effectively sequester CO₂ through carbonate formation, with grain size and mineral composition influencing reaction rates and elemental behavior. These findings support the viability of geologic carbon storage in mafic volcanic terrains and inform strategies for critical element recovery.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Dynamic Bubbling Balanced Proactive CO 2 Capture and Reduction on a Triple-Phase Interface Nanoporous Electrocatalyst

The formation and preservation of the active phase of the catalysts at the triple-phase interface during CO 2 capture and reduction is essential for improving the conversion efficiency of CO 2 electroreduction toward value-added chemicals and fuels under operational conditions. Designing such ideal catalysts that can mitigate parasitic hydrogen generation and prevent active phase degradation during the CO 2 reduction reaction (CO 2 RR), however, remains a significant challenge. Herein, we developed an interfacial engineering strategy to build a new SnO x catalyst by invoking multiscale approaches. This catalyst features a hierarchically nanoporous structure coated with an organic F-monolayer that modifies the triple-phase interface in aqueous electrolytes, substantially reducing competing hydrogen generation (less than 5%) and enhancing CO 2 RR selectivity (~90%). This rationally designed triple-phase interface overcomes the issue of limited CO 2 solubility in aqueous electrolytes via proactive CO 2 capture and reduction. Concurrently, we utilized pulsed square-wave potentials to dynamically recover the active phase for the CO 2 RR to regulate the production of C1 products such as formate and carbon monoxide (CO). This protocol ensures profoundly enhanced CO 2 RR selectivity (~90%) compared with constant potential (~70%) applied at -0.8 V (V vs RHE). We further achieved a mechanistic understanding of the CO 2 capture and reduction processes under pulsed square-wave potentials via in situ Raman spectroscopy, thereby observing the potential-dependent intensity of Raman vibrational modes of the active phase and CO 2 RR intermediates. Finally, this work will inspire material design strategies by leveraging triple-phase interface engineering for emerging electrochemical processes, as technology moves toward electrification and decarbonization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Dual-atom active sites embedded in two-dimensional C 2 N for efficient CO 2 electroreduction: A computational study

Double-atom catalysts (DACs) have emerged as an enhanced platform of single-atom catalyst for promoting electrocatalytic CO 2 reduction reaction (CO 2 RR). Herein, we present a density-functional theory study on CO 2 RR performance of seven C 2 N-supported homo- and heteronuclear DACs, denoted as M 2 @C 2 N. Our results demonstrate that there exists substantial synergistic effect of dual-metal-atom N 2 M 2 N 2 active site and C 2 N matrix on O&#x2550 C &#x2550O bond activation. The dual-atom M 2 sites are able to drive CO 2 RR beyond C 1 products with low limiting potential (U L ). Specifically, C 2 H 4 formation is preferred on FeM@C 2 N (M = Fe, Co, Ni, Cu) versus CH 4 formation on CuM@C 2 N (M = Co, Ni, Cu). Furthermore, *CO+*CO co-binding strength can serve as a descriptor for CO 2 RR activity for making C 2 products such that the moderate binding results in the lowest U L . Remarkably, C-affinity matters most to C—C bond coupling and C 2 H 4 formation while both C- and O-affinity control CH 4 formation. Furthermore, our results provide theoretical insight into rational design of DACs for efficient CO 2 RR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Implanting Transition Metal into Li 2 O-Based Cathode Prelithiation Agent for High-Energy-Density and Long-Life Li-Ion Batteries

Compensating the irreversible loss of limited active lithium (Li) is essentially important for improving the energy-density and cycle-life of practical Li-ion battery full-cell, especially after employing high-capacity but low initial coulombic efficiency anode candidates. Introducing prelithiation agent can provide additional Li source for such compensation. Herein, we precisely implant trace Co (extracted from transition metal oxide) into the Li site of Li 2 O, obtaining (Li 0.66 Co 0.11$\square$0.23 ) 2 O (CLO) cathode prelithiation agent. Further, the synergistic formation of Li vacancies and Co-derived catalysis efficiently enhance the inherent conductivity and weaken the Li-O interaction of Li 2 O, which facilitates its anionic oxidation to peroxo/superoxo species and gaseous O 2 , achieving 1642.7 mAh/g ~Li2O prelithiation capacity (≈980 mAh/g for prelithiation agent). Coupled 6.5 wt % CLO-based prelithiation agent with LiCoO 2 cathode, substantial additional Li source stored within CLO is efficiently released to compensate the Li consumption on the SiO/C anode, achieving 270 Wh/kg pouch-type full-cell with 92 % capacity retention after 1000 cycles.

25 ENERGY STORAGE↗

DOE OSTI2021

Carbonation, strength development, and characterization of calcined limestone as a potential construction material

The emergence of the modern Portland cement has led to the downfall of lime as a construction material. Consequentially, its use has been limited to repair and restoration of historical buildings. Yet, its lower calcination temperature (~950 °C) and the ability to gain strength through carbonation implies its potential as a sustainable alternative to cement. In this study, calcined limestone was studied concerning its carbonation and strength development. Superplasticizer, raw limestone, and different carbonation regimes were explored as techniques to improve the composite strength development, a shortfall that hinders its re-adoption. The results indicated that the raw limestone as a partial replacement of the calcined limestone significantly improved the carbonation degree and mechanical properties. The average compressive strength reached 20 MPa under 20% CO{sub 2} due to the formation of an interconnected network of calcite as the dominant carbonation product. Supercritical CO{sub 2}, in contrast, formed disjoint particles or agglomerates of carbonates.

36 MATERIALS SCIENCE↗

DOE OSTI2022

User’s Manual for Seal_Flux: A Seal Barrier Reduced-Order Model

This report provides a brief description on the use of the Seal_Flux computer program developed as part of the effort to quantify the risk of geologic storage of carbon dioxide (CO 2 ) under the U.S. Department of Energy’s (DOE) National Risk Assessment Partnership (NRAP). The Seal_Flux code simulates the flow of CO 2 through a low permeability rock horizon or seal formation overlying the storage reservoir into which CO 2 is injected. A two-phase, relative permeability approach with Darcy’s law is used for one-dimensional (1D) flow computations of CO 2 through the horizon in the vertical direction. The code also allows the simulation of time-dependent processes that can influence such flow.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

User’s Manual for Seal_Flux: A Seal Barrier Reduced-Order Model (Update)

This report provides a brief description on the use of the Seal_Flux computer program developed as part of the effort to quantify the risk of geologic storage of carbon dioxide (CO 2 ) under the U.S. Department of Energy’s (DOE) National Risk Assessment Partnership (NRAP). The Seal_Flux code simulates the flow of CO 2 through a low permeability rock horizon or seal formation overlying the storage reservoir into which CO 2 is injected. A two-phase, relative permeability approach with Darcy’s law is used for one-dimensional (1D) flow computations of CO 2 through the horizon in the vertical direction. The code also allows the simulation of time-dependent processes that can influence such flow. However, as part of its design, Seal_Flux is what can be termed a “reduced-order model” (ROM) and is not intended as a full-functioning flow code. The theory and simulation in the code is streamlined and directed towards the implementation of Monte Carlo risk analyses of CO 2 transport or as termed in this context as “leakage.” While presented in this report as a stand-alone tool, the Seal_Flux code is intended to function in the future as one of several models as part of an integrated, systems-level model of CO 2 storage performance. Finally, the code is written in Python 3.10 to provide an open framework for further development by others and to assist in linking the code with other modules in an integrated assessment model.

58 GEOSCIENCES↗

NASA NTRS1986

Corrosion of metals and alloys in sulfate melts at 750 C

The corrosion of Ni, Co, Ni-10Cr, Co-21Cr, and IN738 was studied at 750 C in the presence of molten sulfate mixtures (Na2SO4-Li2SO4 and Na2SO4-CoSO4) and in an atmosphere consisting of O2 + 0.12 percent SO2-SO3. The corrosion was observed to be similar for both Na2SO4-Li2SO4 and Na2SO4-CoSO4 melts. The corrosion of Ni and Co took place by the formation of a mixed oxide plus sulfide scale, very similar to the corrosion in SO2 or SO3 alone. The initial stage for the corrosion of Ni-10Cr involved the formation of a thick NiO + Ni3S2 duplex scale, and Cr sulfide was formed during the later stages. A pitting type of morphology was observed for both Co-21Cr and IN738. The pit was Cr sulfide at the beginning, and subsequently the sulfides oxidized to Cr2O3. A base-metal oxide layer was present above the pit, and this was observed to be formed very early in the corrosion process. A mechanism is proposed to explain this. In general, the formation of sulfides appears to be the primary mode of degradation in mixed sulfide melts.

Misra, A. K.↗

NASA NTRSDate not supplied

Simulation of etch pit formation through active sites in carbon fiber micro-structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation as a result of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gasses such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various reaction mechanisms such as adsorption, desorption, Eley-Rideal (ER) and Langmuir-Hinshelwood (LH) mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRSDate not supplied

Simulation of Etch Pit Formation in DSMC Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRSDate not supplied

DSMC Simulation of Etch Pit Formation Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

DOE OSTI2023

Element-Specific Study of Magnetic Anisotropy and Hardening in SmCo 5– x Cu x Thin Films

This work investigates the effect of copper substitution on the magnetic properties of SmCo 5 thin films synthesized by molecular beam epitaxy. A series of thin films with varying concentrations of Cu were grown under otherwise identical conditions to disentangle structural and compositional effects on the magnetic behavior. The combined experimental and theoretical studies show that Cu substitution at the Co 3g sites not only stabilizes the formation of the SmCo 5 structure but also enhances magnetic anisotropy and coercivity. Density functional theory calculations indicate that Sm(Co 4 Cu 3g ) 5 possesses a higher single-ion anisotropy as compared to pure SmCo 5 . In addition, X-ray magnetic circular dichroism reveals that Cu substitution causes an increasing decoupling of the Sm 4f and Co 3d moments. Scanning transmission electron microscopy confirms predominantly SmCo 5 phase formation and reveals nanoscale inhomogeneities in the Cu and Co distribution. Our study based on thin film model systems and advanced characterization as well as modeling reveals novel aspects of the complex interplay of intrinsic and extrinsic contributions to magnetic hysteresis in rare-earth-based magnets, i.e., the combination of increased intrinsic anisotropy due to Cu substitution and the extrinsic effect of inhomogeneous elemental distribution of Cu and Co.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1992

Comet Halley as an aggregate of interstellar dust and further evidence for the photochemical formation of organics in the interstellar medium

Photolysis of mixtures of CO:NH3:H2O at 12 K results in the formation of an organic residue which is not volatile in high vacuum at room temperature. Analysis of this fraction by GC-MS resulted in the detection of C2-C3 hydroxy acids and hydroxy amides, glycerol, urea, glycine, hexamethylene tetramine, formamidine and ethanolamine. Use of isotopically labeled gases made it possible to establish that the observed products were not contaminants. The reaction pathways for the formation of these products were determined from the position of the isotopic labels in the mass spectral fragments. The significance of these findings to the composition of comets and the origins of life is discussed.

Briggs, R.↗

DOE OSTI2020

Impact of Cr and Co on 99Tc retention in magnetite: A combined study of ab initio molecular dynamics and experiments

This work explores the effect of co-mingled dopants, Co(II) and Cr(III), on Tc(IV) incorporation and retention in magnetite when heat treated to 625 or 700 °C. Key trends in Tc retention in the high temperature regime were identified using a combination of density-functional-theory based ab initio molecular dynamics (AIMD) simulations, and batch experiments including solid phase characterization techniques, e.g. X-ray absorption spectroscopy. A stabilizing effect on Tc(IV) was observed when the number of Tc and Cr atoms are equal or when the magnetite surface is oversaturated with Tc and Cr inclusions. Here, oversaturation is hypothesized to force Cr from the magnetite surface to form a Cr2O3 phase, which may act as a protective layer that prevents Tc release. With the addition of Co, Tc(IV) is stabilized via redox processes. The presence of Cr in low concentrations interferes with this redox stabilization and Cr is preferentially stabilized as opposed to Tc. As a result, using Co as a stabilizing dopant for Tc may be compromised in the presence of Cr. When the relative concentration of Tc, Cr and Co is the same, or more Co atoms are added to high Cr incorporated systems, the formation of the Cr2O3 phase may be suppressed. Although waste streams with co-mingled Tc and Cr potentially may benefit from a Co dopant, since the formation of a Cr2O3 passivation layer may protect incorporated Tc from being released, the relative concentration of the three elements will be a critical parameter for maximizing effectiveness of this strategy.

Lee, Mal Soon↗

DOE OSTI2024

Understanding the morphology and chemical activity of model ZrO x /Au (111) catalysts for CO 2 hydrogenation

In this study, the growth of ZrO x on Au (111) was investigated using scanning tunneling microscopy (STM) and synchrotron-based ambient pressure X-ray photoelectron spectroscopy (AP-XPS). Nanostructures of ZrO x (x= 1,2) at the sub-monolayer (≤ 0.3 ML) level were prepared by vapor depositing Zr metal onto Au (111) followed by oxidation with O 2 or CO 2 . At low coverages of the admetal (< 0.05 ML), the formed ZrO x nanostructures were dispersed randomly on the terraces and steps of the Au(111) substrate. Strong oxide-metal interactions prevented the formation of islands of zirconia. The ZrO x nanostructures displayed a reactivity towards CO 2 and H 2 not seen for bulk zirconia. C 1 s AP-XPS results indicated that CO 2 molecules adsorbed on Zr/ZrO x /Au(111) surfaces could undergo partial decomposition on Zr (CO 2 , gas → CO gas + O ads ), or react with oxygen sites from ZrO x to yield carbonates (Zr-CO 3, ads ). Further, after exposing ZrO 2 /Au (111) surfaces to 1:3 mixtures of CO 2 :H 2 , the formation of HCOO, CO 3 , and CH 3 O was detected in AP-XP spectra. These chemical species decomposed at temperatures in the range of 400-600 K, making them possible reaction intermediates for methanol synthesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗