Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Best”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

A method for calculating externally blown flap noise

Several basic noise components were described. These components are: (1) compact lift dipoles associated with the wing and flaps; (2) trailing edge noise associated with the last trailing edge; and (3) quadrupole noise associated with the undeflected exhaust jet and the free jet located downstream of the trailing edge. These noise components were combined to allow prediction of directivity and spectra for under the wing (UTW) slotted flaps with conventional or mixer nozzles, UTW slotless flaps, upper surface blowing (USB) slotless flaps, and engine in front of the wing slotted flaps. A digital computer program listing was given for this calculation method. Directivities and spectra calculated by this method were compared with free field data for UTW and USB configurations. The UTRC method best predicted the details of the measured noise emission, but the ANOP method best estimated the noise levels directly below these configurations.

Fink, M. R.↗
NASA NTRS1973

Ionospheric scintillation studies

The diffracted field of a monochromatic plane wave was characterized by two complex correlation functions. For a Gaussian complex field, these quantities suffice to completely define the statistics of the field. Thus, one can in principle calculate the statistics of any measurable quantity in terms of the model parameters. The best data fits were achieved for intensity statistics derived under the Gaussian statistics hypothesis. The signal structure that achieved the best fit was nearly invariant with scintillation level and irregularity source (ionosphere or solar wind). It was characterized by the fact that more than 80% of the scattered signal power is in phase quadrature with the undeviated or coherent signal component. Thus, the Gaussian-statistics hypothesis is both convenient and accurate for channel modeling work.

Rino, C. L.↗
NASA NTRS1976

Summary of low-speed aerodynamic characteristics of upper-surface-blown jet-flap configurations

The results of recent wind tunnel investigations to provide fundamental information on the upper surface blown (USB) jet flap concept demonstrated that the USB concept provides good high-lift performance. It is shown that the low speed performance is dependent upon the jet turning angle and turning efficiency and on the use of proper leading and trailing edge treatment to prevent premature flow separation. The best means of achieving good turning performance in any particular USB application must be determined from overall operational considerations in which high speed performance, structures and noise, as well as low speed performance, are evaluated. The large diving moments generated at high lift coefficients can be trimmed satisfactorily with a large, conventional horizontal tail; a high tail position is best from longitudinal stability considerations. Large rolling and yawing moments are introduced with the loss of an engine, but these moments can be trimmed satisfactorily through the use of asymmetrical boundary layer control and through the use of spoiler and rudder deflection as needed.

Phelps, A. E., III↗
NASA NTRS1978

Cyclic oxidation of coated Oxide Dispersion Strengthened (ODS) alloys in high velocity gas streams at 1100 deg C

Several overlay coatings on ODS NiCrAl's were tested in Mach 1 and Mach 0.3 burner rigs to examine oxidation and thermal fatigue performance. The coatings were applied by various methods. Based on weight change, macroscopic, and metallographic observations in Mach 1 tests Nascoat 70 on TD-NiCrAl exhibited the best oxidation resistance. In Mach 0.3 tests PWA 267 and ATD-1, about equally, were the best coatings on YD-NiCrAl (Nascoat 70 was not tested in Mach 0.3 rigs).

Gedwill, M. A.↗
NASA NTRS1977

Use of LANDSAT imagery for soil survey

The author has identified the following significant results. The MSS channels 6 and 7 were considered the best to study the relative tonality of different spectral responses of soils, while channels 5 and 7 were best for natural vegetation, drainage patterns, and land use. Frequency ratio was the recommended index for use when analyzing a drainage pattern quantitatively.

Dejesusparada, N.↗
NASA NTRS1977

Viking Observations of Phobos and Deimos: Preliminary Results

The improved resolution of the Viking images has led to the discovery of a number of unusual surface features on Phobos. The features include elongated rill-like depressions associated with the crater Stickney, chains and clusters of irregular elongated craters, and linear striations or grooves. Crater counts are also considered. A total of 27 craters ranging in size from 0.3 to 1.4 km are visible on the best Deimos frame available. Craters ranging from 50 m to 4.9 km in diameter can be observed on the best of the Phobos images.

Veverka, J.↗
NASA NTRS1977

Some new control theoretic models for human operator display monitoring

Control theoretic techniques are applied to develop two new models for predicting human operator performance when monitoring an automatically controlled system. In one case it is assumed that the human monitors the instruments in order to rapidly detect failures. A second approach assumes that the instruments are sampled to best reconstruct the system status information. The relation of these models to existing prediction schemes, e.g., equal attention and the Senders model is explored. It is concluded that a combination of failure detection and status estimation models offers the best potential for human operator application.

Kleinman, D. L.↗
NASA NTRS1977

Failure detection and correction for turbofan engines

In this paper, a failure detection and correction strategy for turbofan engines is discussed. This strategy allows continuing control of the engines in the event of a sensor failure. An extended Kalman filter is used to provide the best estimate of the state of the engine based on currently available sensor outputs. Should a sensor failure occur the control is based on the best estimate rather than the sensor output. The extended Kalman filter consists of essentially two parts, a nonlinear model of the engine and up-date logic which causes the model to track the actual engine. Details on the model and up-date logic are presented. To allow implementation, approximations are made to the feedback gain matrix which result in a single feedback matrix which is suitable for use over the entire flight envelope. The effect of these approximations on stability and response is discussed. Results from a detailed nonlinear simulation indicate that good control can be maintained even under multiple failures.

Corley, R. C.↗
NASA NTRS1978

On attitude estimation schemes for fine-pointing control

This paper studies single-axis equations of motion that are applicable to a spacecraft or to a space experiment pointing assembly whose motion has been perfectly isolated from the carrier vehicle. It considers four state estimators for implementation in the control loop for a stellar observation experiment. The first three estimators are very general and do not make use of input torque in their prediction models, while the proposed fourth estimator utilizes this information. It is shown via closed-loop covariance analysis that the best achievable pointing performance with the best of the first three estimators is limited to about 0.125 arc-sec (rms) with the given rate-gyro and star-tracker inaccuracies. It is also shown that the fourth estimator has the capability of achieving a pointing performance far superior to the performance achievable using the first three estimators. The fourth estimator relies on the ability to accurately generate the desired control torque (i.e., low input noise).

Joshi, S. M.↗
NASA NTRS1978

Solar power satellites - Heat engine or solar cells

A solar power satellite is the energy-converting element of a system that can deliver some 10 GW of power to utilities on the earth's surface. We evaluated heat engines and solar cells for converting sunshine to electric power at the satellite. A potassium Rankine cycle was the best of the heat engines, and 50 microns thick single-crystal silicon cells were the best of the photovoltaic converters. Neither solar cells nor heat engines had a clear advantage when all factors were considered. The potassium-turbine power plant, however, was more difficult to assemble and required a more expensive orbital assembly base. We therefore based our cost analyses on solar-cell energy conversion, concluding that satellite-generated power could be delivered to utilities for around 4 to 5 cents a kWh.

Oman, H.↗
NASA NTRS1978

Prediction of orbiter RSI tile gap heating ratios from NASA/Ames double wedge model test

In-depth gap heating ratios for Orbiter RSI tile sidewalls were predicted based on near steady state temperature measurements obtained from double wedge model tests. An analysis was performed to derive gap heating ratios which would result in the best fit of test data; provide an assessment of open gap response, and supply the definition of gap filler requirements on the Orbiter. A comparison was made of these heating ratios with previously derived ratios in order to verify the extrapolation of the wing glove data to Orbiter flight conditions. The analysis was performed with the Rockwell TPS Multidimensional Heat Conduction Program for a 3-D, 2.0-inch thick flat RSI tile with 255 nodal points. The data from 14 tests was used to correlate with the analysis. The results show that the best-fit heating ratios at the station farthest upstream on the model for most gap depths were less than the extrapolated values of the wing glove model heating ratios. For the station farthest downstream on the model, the baseline heating ratios adequately predicted or over-predicted the test data.

Source record↗
NASA NTRS1979

An objective method for forecasting tropical cyclone intensity and motion using Nimbus-5 ESMR measurements and non-satellite derived descriptors

An empirical analysis program, based on finding an optimal representation of the data was applied to 120 observations of 29 1973 and 1974 North Pacific tropical cyclones. Each observation consists of a field of Nimbus-5 Electrically Scanning Microwave Radiometer radiation measurements at 267 grid points covering and surrounding the tropical cyclone plus nine other non-satellite derived discriptors. Forecast algorithms to estimate storm intensity and motion at 12, 24, 48, and 72 hours after each observation were developed using an independent eigen screening analysis. These algorithms were based on best track data. Independent testing of these algorithms showed that the performance of most of these algorithms were better than persistence and the algorithms forecasting 24, 48, and 72 hour maximum wind speed were better than those made operationally by the Joint Typhoon Warning Center for 1973 and 1974 that did not use best track data.

Hunter, H. E.↗
NASA NTRS1979

Approximate maximum likelihood decoding of block codes

Approximate maximum likelihood decoding algorithms, based upon selecting a small set of candidate code words with the aid of the estimated probability of error of each received symbol, can give performance close to optimum with a reasonable amount of computation. By combining the best features of various algorithms and taking care to perform each step as efficiently as possible, a decoding scheme was developed which can decode codes which have better performance than those presently in use and yet not require an unreasonable amount of computation. The discussion of the details and tradeoffs of presently known efficient optimum and near optimum decoding algorithms leads, naturally, to the one which embodies the best features of all of them.

Greenberger, H. J.↗
NASA NTRS1979

Low Cost Solar Array Project: Composition Measurements by Analytical Photo Catalysis

The applicability of the photon catalysis technique for effecting composition analysis of silicon samples is discussed. A detector for the impurities Al, Cr, Fe, Mn, Ti, V, Mo and Zr is evaluated. During the first reporting period Al, Cr, Fe, and Mn were detected with the photon catalysis method. The best fluorescence lines to monitor and determine initial sensitivities to each of these elements by atomic absorption calibration were established. In the course of these tests vapor pressure curves for these four pure substances were also mapped. Ti and Si were detected. The best lines to monitor were catalogued and vapor pressure curves were determined. Attempts to detect vanadium were unsuccessful due to the refractory nature of this element and the limited temperature range of the evaporator.

Sutton, D. G.↗
NASA NTRS1979

Survey of inorganic polymers

A literature search was carried out in order to identify inorganic, metallo-organic, and hybrid inorganic-organic polymers that could serve as potential matrix resins for advanced composites. The five most promising candidates were critically reviewed and recommendations were made for the achievement of their potential in terms of performance and cost. These generic polymer classes comprise: (1) Poly(arylsil sesquioxanes); (2) Poly(silyl arylene siloxanes); (3) Poly(silarylenes); (4) Poly(silicon-linked ferrocenes); and (5) Poly(organo phosphazenes). No single candidate currently possesses the necessary combination of physicomechanical properties, thermal stability, processability, and favorable economics. The first three classes exhibit the best thermal performance. On the other hand, poly (organo phosphazenes), the most extensively studied polymer class, exhibit the best combination of structure-property control, processability, and favorable economics.

Gerber, A. H.↗
NASA NTRS1979

Study of liquid and vapor flow into a Centaur capillary device

The following areas of liquid and vapor flow were analyzed and experimentally evaluated; 1) the refilling of capillary devices with settled liquid, and 2) vapor flow across wetted screens. These investigations resulted in: 1) the development of a versatile computer program that was successfully correlated with test data and used to predict Centaur D-1S LO2 and LH2 start basket refilling; 2) the development of a semi-empirical model that was only partially correlated with data due to difficulties in obtaining repeatable test results. Also, a comparison was made to determine the best propellant management system for the Centaur D-1S vehicle. The comparison identified the basline Centaur D-1S system (using pressurization, boost pumps and propellant settling) as the best candidate based on payload weight penalty. However, other comparison criteria and advanced mission condition were identified where pressure fed systems, thermally subcooled boost pumps and capillary devices would be selected as attractive alternatives.

Blatt, M. H.↗
NASA NTRS1978

From sunlight in space to 60 Hz on earth - The losses along the way

The space-to-ground links for the Solar Power Satellite System are discussed in terms of worst, best, and nominal efficiency used in the development of the preliminary design. An uncertainty analysis of this design illustrates the effect of link efficiency on SPS size and mass. It is shown that a solar power satellite can deliver power to a ground-based utility for 4 to 5 cents per kWh, depending on the efficiency of the solar cells available in 1987. The overall efficiency of converting sunlight in space to electric power delivered to utilities ranged from 3.83% for the worst combination of efficiencies to 9.5% for the best, with a nominal efficiency of 7.12%.

Denman, O. S.↗
NASA NTRS1977

Current developments in SAW oscillator stability

The results reported were obtained with two port delay lines and resonators used in a simple feedback oscillator. The feedback oscillator employed inherently operates with the amplifier in a saturated condition and, therefore, the AM noise is suppressed. Consequently the dominant noise is FM. Generally, it can be concluded that for very narrow-band, or fixed-frequency applications, the resonator-type oscillator will give the best noise performance. For applications where tunability and linearity are important, the delay-line-type oscillator may give the best performance. There have been no significant improvements in oscillator temperature stability. The only two demonstrated materials for temperature stable SAW oscillators are ST-cut quartz and the SiO2/LiTaO3 overlay structure. Aging tests have been going on for the past two-and-a-half years and it has become obvious that the observed aging rates are largely related to cleaning and packaging.

Parker, T. E.↗