SEARCH · Engineering Papers
Results for “B physics”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Scoping study of lower hybrid current drive for CFETR
The paper assesses the applicability of lower hybrid current drive (LHCD) for two potential operating scenarios for the China Fusion Engineering Test Reactor (CFETR): the “hybrid” scenario in which some of the plasma current is sustained by the Ohmic transformer, and the fully non-inductive “steady state” scenario. Here, the πScope workflow engine was used to set up a large number of ray tracing/Fokker-Planck simulations (> 10 4 ) with parametric scans in the antenna poloidal position and launched parallel refractive index (n || ) for both the hybrid and steady state scenarios. Modeling predicts efficient off-axis current drive (1.3 MA for 20 MW launched power) with a peak near ρ of 0.6-0.65 for waves launched from the high field side (HFS). Waves launched from the low field side (LFS) damp at larger radius (ρ > 0.73) with similar efficiency to HFS launch. Stability analysis of the CFETR scenarios favors current drive profiles peaked near the mid-radius, suggesting that HFS launch is preferable due to the current drive location. The effect of wave scattering from density blobs in the edge/scrape-off-layer region was assessed through rotation of the perpendicular wavenumber at the ray origin. Simulations show that this effect can be quite large both in efficiency and damping location, however by adjusting the launched n|| much of the unperturbed performance can be recovered.
Verification of a quasi-linear model for gyrokinetic turbulent transport
The verification and calibration of a new quasi-linear transport model with a large database of gyrokinetic turbulence simulations is presented in this paper. In a previous paper (Staebler et al 2020 Plasma Phys. Control. Fusion 63 015013), a model for the saturated spectrum of electric potential fluctuations was developed based on the properties of the non-linear 3D spectrum. In this paper, a modification to the overall multiplicative factor in this model is found to be necessary to improve the fit to scans of the temperature and density gradients. The error in the fit of the quasi-linear fluxes of electron and ion energy fluxes is significantly better than for previous saturation models. The spectral shift model for the impact of equilibrium E × B velocity shear (Staebler et al 2013 Phys. Rev. Lett. 110 055003) and the zonal flow mixing model for electron-scale turbulence (Staebler et al 2016 Phys. Plasmas 23 062518) are both revised to be compatible with this new model. Furthermore, the models for the loss of bounce averaging and electron collisions in the TGLF reduced linear equations (Staebler et al 2005 Phys. Plasmas 12 102508) are also changed to improve the linear eigenmodes.
An overview of magneto-inertial fusion on the Z Machine at Sandia National Laboratories
We present an overview of the magneto-inertial fusion (MIF) concept MagLIF (Magnetized Liner Inertial Fusion) pursued at Sandia National Laboratories and review some of the most prominent results since the initial experiments in 2013. In MagLIF, a centimeter-scale beryllium tube or "liner" is filled with a fusion fuel, axially pre-magnetized, laser pre-heated, and finally imploded using up to 20 MA from the Z machine. All of these elements are necessary to generate a thermonuclear plasma: laser preheating raises the initial temperature of the fuel, the electrical current implodes the liner and quasi-adiabatically compresses the fuel via the Lorentz force, and the axial magnetic field limits thermal conduction from the hot plasma to the cold liner walls during the implosion. MagLIF is the first MIF concept to demonstrate fusion relevant temperatures, significant fusion production (>10^13 primary DD neutron yield), and magnetic trapping of charged fusion particles. On a 60 MA next-generation pulsed-power machine, two-dimensional simulations suggest that MagLIF has the potential to generate multi-MJ yields with significant self-heating, a long-term goal of the US Stockpile Stewardship Program. At currents exceeding 65 MA, the high gains required for fusion energy could be achievable.
Stabilization of kink/peeling modes by coupled rotation and ion diamagnetic drift effects in quiescent H-mode plasmas in DIII-D and JT-60U
Magnetohydrodynamic stability at the edge pedestal in several quiescent H-mode (QH-mode) plasmas in DIII-D and JT-60U experiments was analyzed by considering plasma rotation and ion diamagnetic drift effects. It was identified that a kink/peeling mode, which is a prime candidate for a trigger of edge harmonic oscillation in QH-mode, is stabilized by plasma rotation when considering the ion diamagnetic drift simultaneously in both experiments. Furthermore, the stabilizing effect by rotation becomes more effective in case using the rotation profile of the main ion species evaluated by assuming radial force balance. In addition, when inverting the rotation direction, it was found that the kink/peeling mode is more stabilized when considering the rotation of the main ion species, though the mode is less stabilized by the rotation of impurity ion species. The result implies that the kink/peeling mode stability in QH-mode plasmas is sensitive to how the rotation profile is evaluated, but it is shown that a qualitative trend stabilizing the kink/peeling mode by rotation can be reproduced with the poloidal rotation profile of an impurity predicted numerically based on the neoclassical theory.
Orbit tomography of energetic particle distribution functions
Both fast ions and runaway electrons are described by distribution functions, the understanding of which are of critical importance for the success of future fusion devices such as ITER. Typically, energetic particle diagnostics are only sensitive to a limited subsection of the energetic particle phase-space which is often insufficient for model validation. However, previous publications show that multiple measurements of a single spatially localized volume can be used to reconstruct a distribution function of the energetic particle velocity-space by using the diagnostics' velocity-space weight functions, i.e. velocity-space Tomography. In this work we use the recently formulated orbit weight functions to remove the restriction of spatially localized measurements and present orbit tomography, which is used to reconstruct the 3D phase-space distribution of all energetic particle orbits in the plasma. Through a transformation of the orbit distribution, the full energetic particle distribution function can be determined in the standard {energy, pitch, r, z}-space. We benchmark the technique by reconstructing the fast-ion distribution function of an MHD-quiescent DIII-D discharge using synthetic and experimental FIDA measurements. We also use the method to study the redistribution of fast ions during a sawtooth crash at ASDEX upgrade using FIDA measurements. Lastly, a comparison between the orbit tomography and velocity-space tomography is shown.
Fusion pilot plant performance and the role of a sustained high power density tokamak
Here, recent U.S. fusion development strategy reports all recommend that the U.S. should pursue innovative science and technology to enable construction of a fusion pilot plant (FPP) that produces net electricity from fusion at low capital cost. Compact tokamaks have been proposed as a means of potentially reducing the capital cost of a FPP. However, compact steady-state tokamak FPPs face the challenge of integrating a high fraction of self-driven current with high core confinement, plasma pressure, and high divertor parallel heat flux. This integration is sufficiently challenging that a dedicated sustained-high-power-density (SHPD) tokamak facility is proposed by the U.S. community as the optimal way to close this integration gap. Performance projections for the steady-state tokamak FPP regime are presented and a preliminary SHPD device with substantial flexibility in lower aspect ratio (A = 2–2.5), shaping, and divertor configuration to narrow gaps to an FPP is described.
Effects of external kink and fishbone-like modes on energetic particle transport in tokamak plasmas
Transport and loss of beam injected energetic particles (EPs) due to three-dimensional perturbations, associated with the external kink (XK) instability and fishbone-like mode (FLM), are numerically investigated utilizing the guiding center following code ORBIT for static toroidal plasmas in HL-2A. The perturbation structure for the XK is computed by the MARS-F code and then mapped to the Boozer coordinates as defined in ORBIT. The simulation shows that the EP profile experiences a significant change in the middle of the plasma column, when the XK-induced radial magnetic field perturbation amplitude, normalized by the equilibrium field, exceeds a threshold value of about 10 -2 . The EP transport is found to be dominated by a diffusion process instead of convection. Furthermore, by scanning the perturbation frequency as a free parameter while maintaining the XK mode structure (thus mimicking the FLM as observed in DIII-D and JT-60U tokamaks), redistribution and loss of EPs are found to be substantially enhanced due to strong resonances between the FLM and EPs, when the mode frequency exceeds a threshold value of ~2 kHz for the case considered. For either XK or FLM, the response of passing EPs to the perturbation is dominant due to the assumed tangential neutral beam injection. Most lost EPs due to these instabilities are initially passing particles but are eventually lost through trapped orbits.
Super-X and conventional divertor configurations in MAST-U ohmic L-mode; a comparison facilitated by interpretative modelling
Measurements are presented, alongside corresponding interpretative SOLPS-ITER simulations, of the first MAST-U experiments comparing ohmically heated L-mode fuelling scans in Conventional divertor (CD) and Super-X divertor (SXD) configurations. In experiment, at comparable outer mid-plane separatrix electron density, $n_{e,\textrm{sep,OMP}}$, the maximum lower outer target heat load was found to be a factor 16 $\,\pm\,7$ lower in SXD compared to CD. In simulation, a factor 26.8 reduction was found (slightly higher than the experimental range), suggesting an additional reduction in SXD compared to the factor 9.3 expected from geometric considerations alone. According to the simulations, this additional reduction in the SXD is due to a net radial transport of the energy remaining downstream of the $T_e = 5$ eV location. This energy is carried out of the critical (highest heat load) flux tube by deuterium atoms, demonstrating the importance of a longer legged divertor which provides space for this to occur. Importantly, in both simulation and experiment, the SXD has minimal impact on the upstream n e and T e profiles. Spectral inferences of detachment front movement in SXD compare well between simulation and experiment. In regions of high magnetic field gradient, the parallel movement of the front towards the X-point becomes less sensitive to increasing $n_{e,\textrm{sep,OMP}}$, in qualitative agreement with simplified models and previous predictive simulations. Additional aspects, regarding the target ion flux rollover, upstream separatrix temperature and drift effects, are also presented and discussed.
Compatibility of divertor detachment and ELM suppression in DIII-D high- β p plasmas with ITER-similar shape
Abstract Integration of transient and steady-state divertor heat fluxes control with a high-performance core is necessary for future fusion reactors. In recent DIII-D high- β p experiments, divertor detachment and simultaneous edge localized mode (ELM) suppression are demonstrated while the plasma confinement quality is maintained high in ITER-similar shape. By optimizing the neon injection in high- β p scenario with ITER-similar shape, deep detachment and ELM suppression are achieved with a high-performance core ( β N ∼ 2.8, β p ∼ 2.3) at q 95 ∼ 7.5. Partial divertor detachment and suppression of large ELMs are achieved at q 95 ∼ 6. The stability analyses suggest that with low neon injection, the density pedestal becomes higher and steeper and the T i profile also increases, therefore the increased edge pressure and higher current density destabilize the Peeling-Ballooning mode (PBM), which would lead to a large ELM collapse. With strong neon gas puffing, the significantly reduced pedestal pressure and current density, due to the degraded T e pedestal, lead to the stabilization of PBM and ELMs are suppressed. For both cases, the coupling between the large radius internal transport barrier (ITB) and edge pedestal is the key reason for maintaining high global performance. The formation of large radius ITB compensates for pedestal degradation. Such results could provide an attractive scenario to well control the transient and steady-state heat flux onto the divertor plates while maintaining good plasma performance, which is an important step toward the steady-state operation of future fusion reactors.
Results of the MAJORANA DEMONSTRATOR’s Search for Double-Beta Decay of 76 Ge to Excited States of 76 Se
The MAJORANA DEMONSTRATOR is searching for double-beta decay of 76 Ge to excited states (E.S.) in 76Se using a modular array of high purity Germanium detectors. 76 Ge can decay into three E.S.s of 76 Se. The E.S. decays have a clear event signature consisting of a ββ-decay with the prompt emission of one or two γ-rays, resulting in with high probability in a multi-site event. The granularity of the DEMONSTRATOR detector array enables powerful discrimination of this event signature from backgrounds. Using 21.3 kg-y of isotopic exposure, the DEMONSTRATOR has set world leading limits for each E.S. decay, with 90% CL lower half-life limits in the range of (0.56 – 2.1) • 10 24 y. In particular, for the 2v transition to the first 0 + E.S. of 76 Se, a lower half-life limit of 0.68 • 10 24 at 90% CL was achieved.
Measurement of the ionization response of amorphous selenium with 122 keV γ rays
In this work, we performed a measurement of the ionization response of 200 μm-thick amorphous selenium (aSe) layers under drift electric fields of up to 50 V/μm. The aSe target was exposed to ionizing radiation from a 57 Co radioactive source and the ionization pulses were recorded with high resolution. Using the spectral line from the photoabsorption of 122 keV γ rays, we measured the charge yield in aSe and the line width as a function of drift electric field. From a detailed microphysics simulation of charge generation and recombination in aSe, we conclude that the strong dependence of recombination on the ionization track density provides the dominant contribution to the energy resolution in aSe. These results provide valuable input to estimate the sensitivity of a proposed next-generation search for the neutrinoless ββ decay of 82 Se that aims to employ imaging sensors with an active layer of aSe. We estimate the RMS line width of the integrated ionization signal from neutrinoless ββ decay events (of deposited energy 3 MeV) to be 2.0% for a drift field of 50 V/μm. The energy resolution can be improved to 1% by correcting for the charge yield as a function of ionization density along the imaged electron tracks.
Monitoring the SNS basement neutron background with the MARS detector
Here, we present the analysis and results of the first dataset collected with the MARS neutron detector deployed at the Oak Ridge National Laboratory Spallation Neutron Source (SNS) for the purpose of monitoring and characterizing the beam-related neutron (BRN) background for the COHERENT collaboration. MARS was positioned next to the COH-CsI coherent elastic neutrino-nucleus scattering detector in the SNS basement corridor. This is the basement location of closest proximity to the SNS target and thus, of highest neutrino flux, but it is also well shielded from the BRN flux by infill concrete and gravel. Furthermore, these data show the detector registered roughly one BRN per day. Using MARS' measured detection efficiency, the incoming BRN flux is estimated to be 1.20 ± 0.56 neutrons/m 2 /MWh for neutron energies above ~3.5 MeV and up to a few tens of MeV. We compare our results with previous BRN measurements in the SNS basement corridor reported by other neutron detectors.
First Observation of Deuteron-Λ Correlations at RHIC
Explore the source record for details and available documents.
Energy Correlators within Jets in Transversely Polarized Proton-Proton Collisions at √s =200 GeV
Explore the source record for details and available documents.
Measurements of Short-Lived Isomers from Photofission as a Method of Active Interrogation for Special Nuclear Materials
Isomeric fission products, such as 134m Te (T 1/2 = 164 ns) and 136m Xe (T 1/2 = 2.95 μs), are proposed as a signature of special nuclear materials in active interrogation applications. To test this conjecture, monoenergetic 9, 11, and 13 MeV photons from the HIγS facility are used to induce fission of 235 U, 238 U, and 239 Pu targets. The de-excitation γ rays of the isomers are measured using time-gated spectroscopy with high-purity germanium detectors. The 134m Te and 136m Xe isomers are detected and identified by the energy and decay half-life of their characteristic γ-ray transitions. The ratio of yields for these two signature γ rays, corresponding to 134m Te/( 136m Xe + 136 I), is found to be strongly correlated with the identity of the fissioning nuclei. These results show that fission-product isomers may be used in active interrogation to detect and identify special nuclear materials, even providing information on the isotopic enrichment. In conclusion, the feasibility of an active interrogation scenario using a bremsstrahlung beam is discussed.
Pb 9 Cu ( PO 4 ) 6 ( OH ) 2 : Phonon bands, localized flat-band magnetism, models, and chemical analysis
Not provided.
Beyond the proton drip line: Bayesian analysis of proton-emitting nuclei
The limits of the nuclear landscape are determined by nuclear binding energies. Beyond the proton drip lines, where the separation energy becomes negative, there is not enough binding energy to prevent protons from escaping the nucleus. Predicting properties of unstable nuclear states in the vast territory of proton emitters poses an appreciable challenge for nuclear theory as it often involves far extrapolations. In addition, significant discrepancies between nuclear models in the proton-rich territory call for quantified predictions. With the help of Bayesian methodology, we mix a family of nuclear mass models corrected with statistical emulators trained on the experimental mass measurements, in the proton-rich region of the nuclear chart. Separation energies were computed within nuclear density functional theory using several Skyrme and Gogny energy density functionals. We also considered mass predictions based on two models used in astrophysical studies. Quantified predictions were obtained for each model using Bayesian Gaussian processes trained on separation-energy residuals and combined via Bayesian model averaging. Here, we obtained a good agreement between averaged predictions of statistically corrected models and experiment. In particular, we quantified model results for one- and two-proton separation energies and derived probabilities of proton emission. This information enabled us to produce a quantified landscape of proton-rich nuclei. The most promising candidates for two-proton decay studies have been identified. Finally, the methodology used in this work has broad applications to model-based extrapolations of various nuclear observables. It also provides a reliable uncertainty quantification of theoretical predictions.