Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Advanced materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Reliable Protection for an Inverter-Based Resources Dominant Grid: Technology Development and Field Demonstration

The project aimed to address the challenges posed by the rapid growth of inverter-based resources (IBR) such as solar, wind, and battery storage, which have fundamentally changed fault behavior, system strength, and protection performance in bulk power systems. Traditional protection schemes, designed for synchronous generator-dominated grids, are inadequate under high IBR penetration. Overall, the project materially advances protection modeling and simulation capabilities needed to maintain reliable grid protection under high IBR penetration. The results build utility confidence in operating power systems safely and reliably across a wide range of generation mixes, supporting grid modernization goals.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Manufacturability and performance response of developed Ni-based alloys for reactor environments

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) at ORNL and laser powder directed energy deposition (LP-DED) at INL have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. For both the LPBF and LP-DED 282 alloys, annealing at 1,180°C for 1 h resulted in partial recrystallization and a bimodal grain distribution, while subsequent aging for 4 h at 800°C led to the formation of a high density of nano size γ′-strengthening precipitates. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF and LP-DED 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation in the LPBF 282 alloy during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Creep cavitation and cracking at grain boundaries were also observed for the LP-DED 282 alloy, and optimization of the printing strategies and post heat treatments will be needed to fabricate high performance 282 components for high temperature nuclear applications.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Final Report SC0022244

Final Report: Electro-Nano-Pulsing (ENP) Processing of Advanced Materials

36 MATERIALS SCIENCE↗
DOE OSTI2026

AMMT Round Robin 316H HFIR Irradiation Test Matrix and Readiness for Insertion

The Round Robin 316H HFIR-2 irradiation campaign, conducted under the Advanced Materials and Manufacturing Technologies (AMMT) Program, is designed to evaluate the variability in irradiation response of laser powder bed fusion (LPBF) stainless steel (SS)-316H across multiple national laboratories, powder heats, and processing conditions, with comparison to wrought counterparts. A total of 11 materials are intended for irradiation in the High Flux Isotope Reactor (HFIR), targeting two irradiation temperatures (400°C and 600°C) and one level of irradiation damage (2 dpa). This irradiation campaign utilizes the standardized general tensile (GENTEN) capsule design to accommodate subsized tensile specimens of these materials. Thermal analyses were performed to ensure appropriate temperature control by design and uniformity within the capsules. All the capsules for this irradiation except one have been successfully assembled, welded, and tested and are ready for HFIR insertion. The last capsule requires re-build following a failed weld. All eight capsules are intended to be inserted in HFIR cycle 517, which is scheduled to start September 8, 2026. This report summarizes the design, material selection, and readiness for insertion of the capsules.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructure and Mechanical Properties of Ni-based Alloys Fabricated by Laser Powder Bed Fusion

The Advanced Materials and Manufacturing Technologies (AMMT) program is aiming at the accelerated incorporation of new materials and manufacturing technologies into nuclear-related systems. Complex Ni-based components fabricated by laser powder bed fusion (LPBF) could enable operating temperatures at T > 700°C in aggressive environments such as molten salts or liquid metals. However, available mechanical properties data relevant to material qualification remains limited, in particular for Ni-based alloys routinely fabricated by LPBF such as IN718 (Ni- 19Cr-18Fe-5Nb-3Mo) and Haynes 282 (Ni-20Cr-10Co-8.5Mo-2.1Ti-1.5Al). Creep testing was conducted on LPBF 718 at 600°C and 650°C and on LPBF 282 at 750°C. finding that the creep strength of the two alloys was close to that of wrought counterparts. with lower ductility at rupture. Heat treatments were tailored to the LPBF-specific microstructure to achieve grain recrystallization and form strengthening γ' precipitates for LPBF 282 and γ' and γ" precipitates for LPBF 718. In-situ data generated during printing and ex-situ X-ray computed tomography (XCT) scans were used to correlate the creep properties of LPBF 282 to the material flaw distribution. In- situ data revealed that spatter particles are the potential causes for flaws formation in LPBF 282. with significant variation between rods based on their location on the build plate. XCT scans revealed the formation of a larger number of creep flaws after testing in the specimens with a higher initial flaw density. which led to a lower ductility for the specimen.

Dryepondt, Sebastien↗
DOE OSTI2025

A Review of the Research and Development of Brayton Cycle Technology in Nuclear Power Applications with a Focus on Compressor Technology

This study reviews the integration of Brayton Cycle (BC) systems in nuclear power generation, emphasizing their potential to enhance thermal efficiency and operational flexibility over traditional Rankine Cycle (RC) systems. Key working fluids, such as helium (He), supercritical carbon dioxide (sCO 2 ), nitrogen (N 2 ), and air, are evaluated for their performance, efficiency, and compatibility with nuclear systems. He is recognized for its high thermal conductivity and inertness at elevated temperatures, while sCO 2 demonstrates advantages in compactness and efficiency in midrange temperatures. This article also highlights the importance of compressor designs in optimizing BC performance and reviews, available compressor technologies. Axial and centrifugal compressor designs enable efficient gas compression while managing the thermal and mechanical stresses associated with high-pressure operations in nuclear systems. Combined with variable geometry components and advanced materials, these technologies address the challenges posed by varying load conditions. Despite the promising features of BC systems, several challenges persist, including high leakage rates and material degradation under extreme conditions, which necessitate robust sealing technologies and thorough testing. The insights gained from operational experiences at facilities, such as the Oberhausen II plant and the High-Temperature He Test Facility (HHV), underscore the complexities involved in designing high-temperature gas turbines for nuclear applications. This review concludes that as the nuclear industry evolves, BC systems hold significant promise for contributing to a sustainable energy future, particularly in the context of small modular reactors (SMRs) and microreactors. Further exploration of combined cycle configurations that combine BCs with RCs may enhance overall efficiency and flexibility in power generation.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Active Learning for Rapid Targeted Synthesis of Compositionally Complex Alloys

The next generation of advanced materials is tending toward increasingly complex compositions. Synthesizing precise composition is time-consuming and becomes exponentially demanding with increasing compositional complexity. An experienced human operator does significantly better than a novice but still struggles to consistently achieve precision when synthesis parameters are coupled. The time to optimize synthesis becomes a barrier to exploring scientifically and technologically exciting compositionally complex materials. This investigation demonstrates an active learning (AL) approach for optimizing physical vapor deposition synthesis of thin-film alloys with up to five principal elements. We compared AL-based on Gaussian process (GP) and random forest (RF) models. The best performing models were able to discover synthesis parameters for a target quinary alloy in 14 iterations. We also demonstrate the capability of these models to be used in transfer learning tasks. RF and GP models trained on lower dimensional systems (i.e., ternary, quarternary) show an immediate improvement in prediction accuracy compared to models trained only on quinary samples. Furthermore, samples that only share a few elements in common with the target composition can be used for model pre-training. We believe that such AL approaches can be widely adapted to significantly accelerate the exploration of compositionally complex materials.

Chemistry↗
DOE OSTI2025

Evaluating Pretreatment Strategies with Modeling for Reducing Scaling Potential of Reverse Osmosis Concentrate: Insights from Ion Exchange and Activated Alumina

Reverse osmosis concentrate (ROC) treatment is critical for enhancing water recovery and minimizing concentrate volume for disposal, especially in regions facing water scarcity. This study investigates the application of ion exchange (IX) resins and activated alumina (AA) as pretreatment strategies to mitigate scaling in ROC due to high concentrations of total dissolved solids, hardness (Ca 2+ and Mg 2+ ), and silica. Through a series of Langmuir isotherms, continuous column experiments, and model simulation, two types of strong acid cation IX resins and three types of strong base anion IX resins alongside three types of AA were evaluated. Results indicate that AA exhibits superior performance in silica removal, achieving up to a 65% reduction and maintaining performance for up to 800 bed volume without reaching saturation. Model simulation of a secondary reverse osmosis treating ROC after the IX and AA pretreatment indicated an additional water recovery of ~70% using antiscalants. This study demonstrates the potential for achieving higher water recovery while also identifying opportunities for pretreatment improvement. Challenges such as the limited IX capacity treating ROC, which requires frequent regeneration and increases operational costs, along with the restricted regeneration capacity of AA, underscore the importance of innovation. These findings emphasize the critical need for developing advanced materials and optimized strategies to further enhance the efficiency of ROC treatment processes.

activated alumina↗
DOE OSTI2021

Preface

Crystallization via nonclassical pathways is important during the formation of minerals in nature and has become a popular method to synthesize advanced materials on both laboratory and industrial scales. Unlike classical crystal growth pathways via monomer-by-monomer addition, crystallization via nonclassical pathways, such as particle-by-particle attachment, can form larger crystals more quickly. Materials prepared via nonclassical crystallization have been applied in various fields such as energy, catalysis, environment, biomedicine, optics, electrics, and magnetics. Understanding nonclassical crystallization pathways could provide new insights into synthesizing novel materials. This ACS Book series aims to provide updated information on fundamental nonclassical crystallization research, including theory and experiments. It is also intended for experienced researchers, to reinforce their knowledge of the developmental scope of new techniques–especially state-of-the-art in situ characterization tools–to understand mechanisms of crystallization via nonclassical pathways. Topics covered in this book series include: (1) nonclassical nucleation; (2) cluster assembly; (3) particle-based crystallization; (4) crystal formation from amorphous intermedium phases; (5) biomineralization via nonclassical pathways; (6) theoretical developments to simulate nonclassical crystallization; (7) observation of the nonclassical crystallization pathways via various characterization techniques; and (8) the application of nonclassical crystallization. Volume II of the Nonclassical Crystallization Book Series will cover a broad range of topics including particle-based crystallization, biomolecular self-assembly, biomineralization, nanoscale imaging, and applications of nonclassical crystallization.

Zhang, Xin↗
DOE OSTI2023

Pillars of Innovation Across Southeast Idaho & the Interstate-15 Corridor

Since 1949, Idaho National Laboratory (INL) has been home to developing civilian and defense nuclear reactor technologies and managing spent nuclear fuel. Today, INL is the nation’s nuclear energy research laboratory, sustaining the safe and efficient operation of existing reactors, powering science in space, and breaking ground on the future fleet of advanced nuclear reactors. INL is only one of many rising technology resources in the region, however. Along the Interstate 15 (I-15) corridor, technology and cybersecurity industries and intellectual assets are rapidly expanding. Creating an innovation hub in this region would unite capabilities to solve current and future challenges in nuclear reactor sustainment and expanded deployment, integrated fuel cycle solutions, integrated energy systems, advanced materials and manufacturing for extreme environments, and secure and resilient cyber-physical systems.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Environmental Effects

This presentation provides an overview of the Environmental Effects Technical Area within the Advanced Materials and Manufacturing Technologies (AMMT) program for the 2024 AMMT program review meeting.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

A Primer on Using Analysis to Guide Plastic Circularity

BOTTLE, funded by DOE's Advanced Materials & Manufacturing Technologies Office and Bioenergy Technologies Office (BETO), conducts analysis-guided R&D to change the way we recycle plastics. But what does analysis really mean? In this webinar, BOTTLE Analysis Co-Lead Dr. Taylor Uekert, a researcher with the National Renewable Energy Laboratory (NREL), will introduce key analysis techniques such as techno-economic analysis, life cycle assessment, and environmental justice evaluation. Relevant to both analysts and non-analysts, Dr. Uekert will cover the basics of analysis techniques and discuss how these methods are conducted and interpreted. She will provide examples from the BOTTLE portfolio demonstrating their use in benchmarking and optimizing the costs and environmental impacts of new innovations in plastic redesign and recycling. If you are working in the plastics recycling field - from experimental work to analysis to community-focused projects - you won't want to miss this talk. The webinar will end with a Q&A session.

analysis↗
DOE OSTI2024

Plasma heating technology

The operational environment for plasma heating systems presents unprecedented challenges for the success of magnetic fusion. This chapter discusses the current state of ion cyclotron and electron cyclotron heating systems and the research and development priorities needed to establish working solutions for these systems. While much progress has been made, there is much more work to be done to make fusion energy commercially viable. Research and development priorities include radiation-resistant structural and plasma facing materials, advanced manufacturing methods, new cooling methods, first-wall integrated actuators, improvements in power source efficiency, higher frequency gyrotrons, and improved overall system reliability.

Caughman, John↗
DOE OSTI2025

Report on the Assessment of Ion Irradiations on High Entropy Alloys

Idaho National Laboratory (INL) initiated a joint international effort with the Czech Republic to explore the feasibility of manufacturing High Entropy Alloys for high-temperature nuclear applications using Additive Manufacturing. This effort was funded at INL by the United States Department of Energy’s Office of Nuclear Energy under the Advanced Reactor Technologies and Advanced Materials and Manufacturing Technologies (AMMT) Program. The High Entropy Alloys were specifically designed for the corrosive and irradiation environments as experienced in gas fast reactors, molten salt reactors, and fusion power. These alloys were manufactured by multiple processes to determine the impact of manufacturing processes on the performance of the alloys in corrosive and irradiation environments. Preliminary results show that MoNbTiV and MoNbTi alloys exhibit no degradation after multiple corrosion tests. These MoNbTiV and MoNbTi alloys were also evaluated after irradiation experiments were conducted at the Michigan Ion Beam Laboratory at the University of Michigan, which is the focus of this milestone report. For these irradiation experiments, the MoNbTiV and MoNbTi alloys manufactured by arc melting and Electric Field Assisted Sintering (EFAS) were tested at 500 C at a dose of 30 dpa to evaluate the microstructural stability and decomposition.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

DOE provides targeted technical assistance for manufacturers pursuing energy and resource efficiency

The U.S. Department of Energy (DOE) is committed to providing the industrial sector with resources and funding to support the development of innovative new technologies and processes. Previously, DOE’s Advanced Manufacturing Office was the front door of the department for many manufacturers. This office focused on two main missions: driving innovation in manufacturing technologies, and reducing energy and emissions related to manufacturing. These missions complemented each other in many ways, but as attention in these areas grew, so too did the need for specialization. In October 2022, the Advanced Manufacturing Office was reorganized into two new offices: the Advanced Materials and Manufacturing Technologies Office (AMMTO) and the Industrial Efficiency and Decarbonization Office (IEDO). For emissions-heavy industries, such as ceramics and glass, the latter office provides research and development funding, technical assistance, and demonstration support to help manufacturers along their journey to reduce emissions and increase resource efficiency. This article overviews the portfolio of resources applicable to ceramic and glass manufacturers through IEDO, including programs that were portioned into this office during the split and new offerings that were added since then. These programs and resources include energy management support, technology-specific guidance, and in-plant technical assistance.

Source record↗
DOE OSTI2026

2026 Site Development Plan

The 2026 edition of the Site Development Plan focuses on 30 years of infrastructure plans as they strengthen the core Science, Technology, and Engineering (ST&E) pillars of Lawrence Livermore National Laboratory (LLNL): High-Energy-Density (HED) Science, Advanced Materials and Manufacturing (AMM), and High Performance Computing (HPC).

Tran, Lucas [Lawrence Livermore National Laborator↗