SEARCH · Engineering Papers

Results for “Additively Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Porosity evolution under increasing tension in wire-arc additively manufactured aluminum using in-situ micro-computed tomography and convolutional neural network

Internal defects such as porosities are often formed in additively manufactured metal components. The pores nucleate, grow, and coalesce to form cracks under loads, leading to eventual catastrophic failure. Here, in this paper, the full-field porosity evolution, including pore growth and coalescence in a wire-arc additively manufactured (WAAM) aluminum alloy cylinder under tension is observed with in-situ X-ray micro-computed tomography (μCT). The pore size distribution, density, and tensile stress are calculated from the volumetric images analyzed by a convolutional neural network (CNN) algorithm, which provides rapid analysis of 12,950 slice images from μCT volumetric images at the reference state and 13 tensile strains. The results show the quantitative evolution of the growth and coalescence of macropores under tension. A strong correlation is found between the local pore volume fraction and the true tensile stress when the tensile strain is larger than 5%.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Additively manufactured Al-Ce-Ni-Mn alloy with improved elevated-temperature fatigue resistance

Here, the high cycle fatigue behavior of an additively manufactured (AM) Al-10.5Ce-3.1Ni-1.2Mn wt% alloy was evaluated at 350 °C. The measured fatigue strength of 50 MPa at this temperature is comparable to the most fatigue resistant wrought Al alloys (2618-T6 and 7079-T6) at 315 °C. Refinement of pore populations through advanced AM processing in the examined alloy led to oxide inclusions becoming dominant fatigue crack initiation sites. The distribution of microstructural features that determine crack initiation was measured by X-ray computed tomography and served as input to make fatigue strength model predictions with various methodologies. A Monte-Carlo based approach that was previously applied to predict the fatigue strength of cast aluminum alloys through pore size distributions yielded accurate predictions for the fatigue strength of this AM alloy. Given the tunability of defect distributions in AM alloys, the sensitivity of the Al-Ce-Ni-Mn alloy fatigue behavior to defect distributions and outstanding elevated-temperature fatigue resistance of this alloy; the results together suggest the possibility of a new generation of fatigue-resistant alloys produced by the additive manufacturing route.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Additive manufacturing methods using aluminum-rare earth alloys and products made using such methods

Described herein are additive manufacturing methods and products made using such methods. The alloy compositions described herein are specifically selected for the additive manufacturing methods and provide products that exhibit superior mechanical properties as compared to their cast counterparts. Using the compositions and methods described herein, products that do not exhibit substantial coarsening, such as at elevated temperatures, can be obtained. The products further exhibit uniform microstructures along the print axis, thus contributing to improved strength and performance. Additives also can be used in the alloys described herein.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Additive manufacturing methods using aluminum-rare earth alloys and products made using such methods

Plotkowski, Alex J.↗

DOE OSTI2024

Development of Solid Synchronous Reluctance Rotors With Multi-Material Additive Manufacturing

Synchronous reluctance (SynR) machines are promising rare-earth material-free alternatives to permanent magnet machines. However, structural challenges limit their operating speed and power density. This paper proposes and investigates multi-material additive manufacturing (MMAM) as a key-enabler to realize power-dense and high-speed SynR machines. It does so by proposing designs that guide magnetic flux through solid rotors realized by selective placement of magnetic and non-magnetic materials. To explore this concept, first, material samples are additively manufactured and experimentally characterized to assess the structural and magnetic properties that can be expected for the proposed rotors. Second, the design space of each rotor type is explored using these measured properties within finite element analysis. The results reveal that MMAM can enable fabrication of SynR motors with power density levels that are at the leading edge of all conventional electric machine topologies. It is shown that tip speeds in excess of 300 m/s can be achieved, resulting in 3-4x improvement in power density over conventional SynR motors. A solid SynR rotor is printed in an experimental MMAM laser powder bed fusion system. The rotor is paired with an existing stator to create a functional SynR motor with a saliency ratio of 2.59 and torque rating of 4.15 Nm. This is the first publication of a SynR rotor prototype constructed via MMAM.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Unveiling Atomistic Mechanisms Governing Additive Manufacturing Processability and Mechanical Behavior of a Refractory Complex Concentrated Alloy

Extending the concept of complex concentrated alloys (CCAs) to the refractory alloys (solidus temperature over 2000 °C) space potentially facilitates the design of lightweight structural alloys with service temperatures that exceed those of Ni and Co‐based alloys. However, the room and elevated temperature tensile properties of the current refractory‐CCAs (R‐CCAs) are inferior to those of the Ni/Co‐based alloys. Furthermore, the manufacturing scalability of R‐CCAs remains challenging, in that cracks are prevalent in all R‐CCAs when processed using near‐net shape manufacturing processes, such as fusion‐based additive manufacturing (F‐BAM). Still, mechanisms governing the poor F‐BAM processability of R‐CCAs remain unexplored. Here, to this end, this work unveils the atomistic mechanisms underlying F‐BAM process‐induced cracking in a NbTiTaMoHfZrC R‐CCA. The implications of light elements’ presence for intrinsic ductility and grain boundary cohesion, and subsequently for F‐BAM processability and mechanical behavior, are revealed. Leveraging the insights, we accomplish what is, to the best of the knowledge, the first instance of crack‐free F‐BAM processing of any R‐CCA. Additionally, the R‐CCA exhibits over 20% tensile ductility and ≈160 MPa tensile yield strength at 1200 °C. In addition to facilitating the design of lightweight R‐CCAs, findings enable scalable manufacturing of these ultra‐high temperature alloys for structural applications.

Refractory alloys↗

DOE OSTI2021

A constitutive structural parameter c b for the work hardening behavior of additively manufactured Ti-6Al-4V

The mechanical behavior of Ti-6Al-4V produced by additive manufacturing processes is assessed as based on a model derived from the Kocks–Mecking relationship. A constitutive parameter c b is derived from a linear Kocks–Mecking relationship for the microstructure that is characteristic of the work hardening behavior. The formulation for c b is determined by considering the plastic strain between the strengths at the proportional limit and the plastic instability. In this way, the model accommodates the variation in work hardening behavior observed when evaluating material as produced and tested along different orientations. The modeling approach is presented and evaluated for the case of Ti-6Al-4V additively manufactured materials as tested under quasi-static uniaxial tension. It is found that different test specimen orientations, along with postbuild heat treatments, produce a change in the microstructure and plasticity behavior which can be accounted for in the corresponding change of the c b values.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Unravelling Microstructure Selection in an Additively Manufactured Eutectic High‐Entropy Alloy

High-entropy alloys (HEAs) are promising candidates for advanced structural applications due to their excellent mechanical properties. Additive manufacturing (AM), with its rapid solidification conditions, enables the creation of unique nonequilibrium microstructures. To fully leverage the synergy between AM and HEAs, understanding how processing affects structure and properties is essential. Here, how solidification rate influences microstructure evolution and phase transformation pathway in laser additively manufactured AlCrFe2Ni2 eutectic HEAs is investigated. By increasing the laser scan speed and hence the solidification rate, distinct solidification modes evolving from coupled eutectic to anomalous eutectic and eventually to single-phase solidification are revealed. These transitions result in distinct microstructures and a wide range of mechanical properties. Thermodynamic modeling and molecular dynamics simulations reveal that low cooling rates allow for sufficient atomic diffusion and phase separation, facilitating coupled eutectic growth. In contrast, rapid cooling suppresses diffusion and destabilizes the solid–liquid interface, promoting anomalous or single-phase solidification. This integrated experimental and computational approach provides a multiscale understanding of solidification mechanisms in HEAs and underscores how kinetic effects can over-ride thermodynamic predictions under nonequilibrium conditions. Furthermore, these results demonstrate that AM can serve as a powerful tool to design HEAs with tailored microstructures and properties.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Additive Manufacturing of Stamping Tools for Appliances

Oak Ridge National Laboratory (ORNL) worked with Whirlpool Corporation to demonstrate additive manufacturing (AM) of stamping dies for the appliance industry using a large-scale wire arc metal additive manufacturing system jointly developed between Lincoln Electric and ORNL. An appliance stamping die was successfully printed, machined, nitrided, and demonstrated in the last quarter of 2019.

42 ENGINEERING↗

DOE OSTI2023

Multimodal and multiscale strengthening mechanisms in Al-Ni-Zr-Ti-Mn alloy processed by laser powder bed fusion additive manufacturing

The unique thermokinetics of laser-powder bed fusion additive manufacturing (L-PBFAM) has been exploited for development of a novel high-strength Al-Ni-Ti-Zr-Mn alloy. The addition of 0.5 wt% Mn leads to extraordinary improvement in ultimate tensile strength (502 MPa) and work hardening due to the activation of two Mn-induced strengthening mechanisms. First, by a bimodal particle strengthening effect due to Al 31 Mn 6 Ni 12 nano-quasi-crystal particles rejected in inter-dendritic spaces and fibrous Al 3 Ni eutectic dendritic channels, which predominately contributes to the strength improvement, and second by solid solution strengthening from remaining Mn entrapped in Al. These mechanisms supplement the particle strengthening effect imparted by coherent and incoherent Al 3 (Ti,Zr) co-precipitates present at melt pool boundaries, dislocation strengthening due to solidification induced strain, and Hall-Petch and backstress strengthening effect due to heterogenous grain size distribution occurring at various length scales. In conclusion, the solidification dynamics and hierarchical heat distribution that are associated with L-PBFAM resulted in complex spatial variations in these strengthening phenomena and were investigated via a high-throughput multiscale structure–property correlation that involved thermokinetic simulation, X-ray diffraction, high-resolution nanoindentation mapping, and site-specific transmission electron microscopy of the alloy.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Orientation-selected micro-pillar compression of additively manufactured 316L stainless steels: Comparison of as-manufactured, annealed, and proton-irradiated variants

In this work, irradiation response and deformation mechanisms of additively manufactured (AM) 316L stainless steel were studied by atomic scale characterization and micro-pillar compression. The AM 316L stainless steels were fabricated by direct energy deposition, a laser-based additive manufacturing process. Irradiation with 2 MeV protons at 360°C was performed to create ~1.8 displacements-per-atom (dpa) damage in AM 316L. Deformation behaviors of the as-manufactured, annealed, and proton-irradiated variants were studied, focusing on the effects of manufacturing-induced pores, residual stress, and irradiation-introduced defects (dislocation loops and voids). Micro-pillars were prepared from grains of pre-selected orientation, avoiding contributions of grain boundaries and allowing determination of resolved shear stress on {111} glide planes. Transmission electron microscopy was used to characterize the pre- and post-deformation microstructure. It was found that in the as-manufactured alloy variant, moving dislocations were the major deformation carrier, with noticeable blocking by fabrication-induced pores, In the annealed variant, hardness was reduced, and deformation was also accomplished by dislocation gliding. In the proton-irradiated variant, significant twinning was observed. Comparing measured resolved shear stress and predicted critical stress for dislocation dissociation, we conclude that irradiation hardening became high enough to activate twinning. Therefore, the deformation mechanism changes from dislocation gliding to twinning. The study is important for both processing optimization and performance evaluation of AM alloys for reactor applications.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Magnetic feed material and its use in producing bonded permanent magnets by additive manufacturing

A method for producing magnet-polymer pellets useful as a feedstock in an additive manufacturing process, comprising: (i) blending thermoplastic polymer and hard magnetic particles; (ii) feeding the blended magnet-polymer mixture into a pre-feed hopper that feeds directly into an inlet of a temperature-controlled barrel extruder; (iii) feeding the blended magnet-polymer mixture into the barrel extruder at a fixed feed rate of 5-20 kg/hour, wherein the temperature at the outlet is at least to no more than 10° C. above a glass transition temperature of the blended magnet-polymer mixture; (iv) feeding the blended magnet-polymer mixture directly into an extruding die; (v) passing the blended magnet-polymer mixture through the extruding die at a fixed speed; and (vi) cutting the magnet-polymer mixture at regular intervals as the mixture exits the extruding die at the fixed speed. The use of the pellets as feed material in an additive manufacturing process is also described.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Design and Cooling Performance of Additively Manufactured Ceramic Turbine Vanes

Ceramic materials are of significant interest in aviation and power generation gas turbine engines due to their low density and ability to withstand high temperatures. Increased cycle thermal efficiency and higher specific power output is possible by incorporating ceramic components that enable high turbine inlet temperatures and lower required cooling airflow levels. However, ceramics can be difficult and costly to form into the complex shapes used in gas turbine components, often requiring specialized multi-step processes. Furthermore, ceramic components in the hottest areas of a gas turbine, such as vanes or blade shroud seals, will still likely require cooling which is challenging to implement in conventional ceramic manufacturing approaches. Therefore, this study presents a multidisciplinary approach that investigates the design, fabrication, and overall cooling effectiveness evaluation of additively manufactured (AM), polymer derived ceramic (PDC) turbine vanes. A thermo-mechanically optimized vane design was generated, ceramic additive manufacturing of the complex cooling configuration was developed, and quantification of the increase in overall cooling effectiveness was performed in a 1X scale, high-speed facility using infrared thermography. This study produced a PDC AM process, capable of printing complex internal cooling schemes in 1X scale turbine vanes. Furthermore, it was found that the optimized vane more than doubled the overall cooling effectiveness observed in the baseline design, which reasonably agreed with thermomechanical optimization model predictions. Additionally, the optimized ceramic vane outperformed an identical metal vane, in terms of area averaged cooling effectiveness, suggesting that the ceramic vane could operate at reduced coolant flowrates to achieve comparable levels of cooling performance.

Reynolds number↗

DOE OSTI2022

Rapid Alloy Selection and Additive Manufacturing of Nickel Based Superalloys

In this work the rapid alloy selection and subsequent processability via additive manufacturing of nickelbased superalloys was investigated. Rapid alloy selection protocols developed within the project produced two viable nickel-based superalloys. This phase I CRADA demonstrates a viable route for selecting new nickel-based superalloys for additive manufacturing.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Demonstration and analysis of volumetric additive manufacturing via sub-orbital spaceflight testing

Computed Axial Lithography (CAL) represents a significant advancement in the emerging field of Volumetric Additive Manufacturing (VAM). CAL addresses key limitations of traditional photopolymer additive manufacturing technologies, by eliminating the need for layering and support structures. Unlike conventional methods, CAL prints components by illuminating all points within a desired geometry simultaneously, using tomographic reconstruction to form the object in a single step. This unique approach eliminates the relative motion between the object and the precursor material, enabling faster printing speeds and reducing the waste associated with support structures. However, CAL parts require post-processing steps before they can be utilized. CAL's core attributes make it particularly suited for In-Space Manufacturing (ISM), due to its fast fabrication times, wide breadth of materials it can use, and minimized footprint. CAL has been successfully demonstrated in microgravity during parabolic flight experiments. However to fully validate and understand CAL's behaviour in microgravity, all manufacturing and post-processing steps must be integrated. In June 2024, we conducted SpaceCAL Mission 3, testing this entire workflow on a suborbital flight aboard Virgin Galactic's SpaceShipTwo. During ~140 s of microgravity, the system autonomously manufactured and post-processed four parts using PEGDA700 resin. Post-flight analysis showed that 2/4 parts were recognisable, while others were distorted due to bubble formation from residual water droplets, off-axis optical aberrations, and non-uniform solvent rinsing. Despite these limitations, this study represents the first integrated CAL workflow in space, providing an initial experimental demonstration and analysis for closed-loop in-space manufacturing.

Waddell, Taylor [Department of Mechanical Engineer↗

DOE OSTI2022

Additive Manufacture of Multi-Functional, Large-Scale Components

The poster summarizes the main results for a LDRD focused on developing a arc-based additive manufacturing (AM) system capable of fabricating large components with a composition gradient otherwise known as functionally graded materials (FGMs). FGMs are capable of addressing local extreme conditions in an optimal and cost-effective manner. The AM system (referred to as multi-Wire Arc Additive Manufacturing or m-WAAM) consisted of modifying a standard automated gas tungsten arc welding system to deliver multiple welding wires to the weld pool at controlled rates to deposit desired alloy compositions at critical locations. Numerous shapes and composition gradients were fabricated with the system and the effect of various deposition parameters on the nature of the composition profile were evaluated. Additionally, heat treatment of the FGM was performed to develop graded microstructures which should enhance dynamic impact performance of inexpensive steels. The project highlights the potential of m-WAAM to efficiently fabricate FGMs. However, this project only explored the science behind the technique and additional development work will be required to develop a fully-functional system that can build more complex components.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Topology optimization of additively manufactured fluidic components free of internal support structures

This report integrates projection-based approaches for implementing overhang constraints with fluid topology optimization to design additively manufactured fluidic components that do not require internal support structures. Internal support structures are challenging, potentially impossible to remove in complex fluid networks, yet would degrade fluidic performance if left within the part. This presents a major challenge in coupling topology optimization with additive manufacturing in the design of fluid components. The proposed approach leverages past work in overhang constraints for solid mechanics, including projection formulations and adjoint sensitivity analysis, and considers incompressible Navier–Stokes equations for laminar fluid flow. The approach is demonstrated on 2D and 3D fluid topology optimization problems to minimize pressure drop and constrain mass flow rates in pipes and manifolds. Resulting designs are crisp, logical, satisfy performance constraints, and satisfy overhang constraints, eliminating the need for internal support structures.

42 ENGINEERING↗

DOE OSTI2022

Influence of microstructural heterogeneities on small-scale mechanical properties of an additively manufactured Al-Ce-Ni-Mn alloy

Laser powder bed fusion-based additive manufacturing (AM) is a promising method to fabricate creep-resistant Al-rare earth alloys (Al-Ce-Ni-Mn) with stable microstructures at up to 400°C. However, creep testing of these alloys at high temperatures shows that void coalescence and failure initiation occurs along the melt pool boundaries in the microstructure. Hence it is crucial to understand how the local mechanical behavior of the melt pool boundaries would influence the global properties of the AM produced alloy. In this study, in situ nanoindentation conducted at room temperature and 300°C revealed a reduced hardness at the melt pool boundaries. Similarly, micro-pillar compression showed a slight decline in yield strength at these boundaries, indicating that they are the weak spots in the microstructure. Such multimodal local mechanical property studies are necessary for understanding the influence of melt pool boundaries on the bulk response of fusion-based AM alloys.

36 MATERIALS SCIENCE↗