Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AGGLOMERATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Structural And Electrical Properties oF (La{sub 0.5-x}Pr{sub x}Ba{sub 0.5})(Mn{sub 0.5}Ti{sub 0.5})O{sub 3} Perovskite

A single phase monoclinic new perovskite based titano-manganite (La{sub 0.5-x}Pr{sub x}Ba{sub 0.5})(Mn{sub 0.5}Ti{sub 0.5})O{sub 3} has been successfully prepared by ceramic solid-state technique at sintering temperature of 1300 deg. C. The concentration of Pr (Praseodymium), x, in molar proportion in A site has been varied as x = 0, 0.02 and 0.2. Analysis has been carried out to determine the electrical properties of the synthesized material at frequency ranging from 5 Hz to 1 MHz; and at temperature range between 25 deg. C to 200 deg. C. It is found that Pr addition promoted liquid phase sintering diffusion, porosity and agglomeration formation at 1300 deg. C. Dual relaxation is observed in unsubstituted Pr sample x = 0 and high Pr substituted sample x = 0.2. This phenomenon was a combinational contribution from a quasi dc (QDC) or low frequency dispersion (LFD), two cole-cole relaxational responses and a resistor. While low concentrated Pr substituted sampled x = 0.02 shows a combinational contribution from a quasi dc (QDC) or low frequency dispersion (LFD), single cole-cole relaxational response and a resistor at room temperature. Pr substitution at x = 0(max 12000) and x = 0.2(max 16000) showed high dielectric values compared to low substituted sample x = 0.02. Variation of dielectric loss tangent (tan delta) are observed for all samples at temperature ranged studied.

36 MATERIALS SCIENCE↗

Atomic structure of amorphous and crystallized Ge{sub 15}Sb{sub 85}

Ge{sub 15}Sb{sub 85} is a promising material for phase-change memory applications owing to its very short crystallization times. As deposited amorphous samples of sputter deposited Ge{sub 15}Sb{sub 85} have been investigated by extended x-ray absorption fine structure (EXAFS) measurements on both, Sb and Ge K absorption edges. After crystallizing the specimen, x-ray diffraction (XRD) and EXAFS measurements have been performed to analyze the atomic structure at different annealing conditions. Thus, experimental techniques focusing on the long range order as well as on the local order have been combined. Sb atoms have on average 3.2(2) nearest neighbors, while Ge atoms have 4.0(3). The Ge-Ge and Ge-Sb bond lengths are determined to 2.46(2) and 2.66(1) A, respectively and agree well with those observed in the amorphous phase of the common phase-change material Ge{sub 2}Sb{sub 2}Te{sub 5}. After crystallizing the sample at 250 deg. C, very different EXAFS spectra with modified Ge-Sb bond lengths are observed. The higher concentration of Ge neighbors at the Ge edge as compared to the as-deposited sample is indicative for phase separation. For the corresponding sample, XRD does not show reflections of Ge, which indicates that the agglomeration of Ge is amorphous or below the coherence length of the x-radiation. The EXAFS spectrum shows a superposition of two phases: one with bond lengths which agree with sp{sup 3}-hybridized Ge [2.43(1) A] and another one with longer Ge-Ge bond lengths [2.79(8) A]. This result can be explained by phase separation in the material.

36 MATERIALS SCIENCE↗

mu-Scale Variations Of Elemental Composition In Individual Atmospheric Particles By Means Of Synchrotron Radiation Based mu-XRF Analysis

Atmospheric pollution poses a huge challenge especially for densely populated urban areas. Although a tremendous knowledge already exists on atmospheric particulate pollution, only very limited knowledge is available on mineral and chemical composition of single atmospheric particles because most studies on air pollution focus on total mass concentrations or bulk elemental analysis. However, it is of particular importance to investigate the properties of single particles since according to their individually composition they differ in their specific impact on climate change, negative environment and health effects, as well as accelerating the weathering of stone buildings in urban areas. Particles with sulfate and nitrate coatings together with sufficient moisture increase metal solubility and possibly catalyze further surface reactions on stone facades of buildings. From the viewpoint of health effects of aerosols it is important to consider agglomerations processes of fine anthropogenic and highly toxic particles with coarse geogenic and less toxic particles. With respect to fundamental research in mineralogy, processes forming composed coarse particles consisting of geogenic and anthropogenic substances are valuable to study since a new type of particle is produced. In this context, the important and still in detail unknown role of geogenic particles as catchers for anthropogenic aerosols can be investigated more closely. Coarse particles can provide a possible sink for fine particles. Moreover, the intermixture of particles from geogenic and anthropogenic sources and the spatial and temporal variations of contributions from different sources, which plays a decisive role in the study area of Beijing, can be clarified with this approach. For this study, particles were collected with the passive sampling device Sigma-2 and analyzed for particles from 3 to 96 {mu}m. The analyzed particles showed a very inhomogeneous distribution in their elemental composition. For this study, synchrotron radiation based mu-X-ray fluorescence analysis (mu-SXRF) proved to be an excellent tool to investigate mu-scalic distributions of main and trace element concentrations within individual airborne particles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural morphology of acoustically levitated and heated nanosilica droplet

We study the vaporization and precipitation dynamics of a nanosilica encapsulated water droplet by levitating it acoustically and heating it with a CO{sub 2} laser. For all concentrations, we observe three phases: solvent evaporation, surface agglomeration, and precipitation leading to bowl or ring shaped structures. At higher concentrations, ring reorientation and rotation are seen consistently. The surface temperature from an infrared camera is seen to be dependent on the final geometrical shape of the droplet and its rotation induced by the acoustic field of the levitator. With nonuniform particle distribution, these structures can experience rupture which modifies the droplet rotational speed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of annealing and Nd concentration on the photoluminescence of Nd{sup 3+} ions coupled with silicon nanoparticles

We report on the microstructure and photoluminescence (PL) properties of Nd-doped SiO{sub 2} thin films containing silicon nanoparticles (Si-np) as a function of the annealing temperature and the Nd concentration. The thin films, which were grown on Si substrates by reactive magnetron co-sputtering, contain the same Si excess. Fourier transform infrared (FTIR) spectra show that a phase separation occurs during the annealing due to the agglomeration of the Si excess resulting in the formation of Si-np. Besides, after annealing, the films exhibit PL from excitonic states confined in Si-np. We showed that the intensity of the PL of Nd{sup 3+} ions that occurs at {approx}0.92, 1.06, and 1.4 {mu}m is maximal at low Nd concentration and while well-passivated Si-np are formed. FTIR and x-ray measurements showed that the increase in the Nd incorporation has detrimental effects on the PL of Nd{sup 3+} because of the formation of Nd{sub 2}O{sub 3} nanocrystals and inherent disorder in the SiO{sub 2} host matrix. PL excitation measurements demonstrate that the PL of Nd{sup 3+} ions is nonresonant and follows the excitation of Si-np giving new evidence of the energy transfer from Si-np toward the rare earth ions.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Preparation of Cu and Fly Ash Composite by Powder Metallurgy Technique

Cu and Fly Ash (FA) mixtures with different weight percentages were prepared. Pellets of the mixture powder were produced with the dimension of 17.7 mm in diameter and 10-15 mm in height. These different composites were compacted at a constant pressure of 280 MPa. One of the selected weight percentages was then compacted to form into pellet and sintered at different temperatures which were at 900, 950 and 1000 deg. C respectively for 2 hours. Density of green pellet was measured before sintered in furnace. After sintering, all the pellets with different temperatures were re-weighed and sintered density were calculated. The densification of the green and sintered pellets was required to be measured as one of the parameter in selection of the best material properties. Porosity of the pellet shall not be ignored in order to analyze the close-packed particles stacking in the pellet. SEM micrograph had been captured to observe the presence of pores and agglomeration of particles in the sample produced.

36 MATERIALS SCIENCE↗

Formation of ZnO Nanocrystalline via Facile Non-Hydrolytic Route

Zinc oxide (ZnO) nanocrystalline were synthesized via oxidizing Zn powder in non-aqueous solvent with addition of Diethanolamine (DEA) as a stabilizing agent. The influence of DEA on the structural, optical properties and the formation of ZnO nanocrystalline were studied. The synthesized ZnO were polycrystalline in structures where sample without the addition of DEA shows high intensity peak of (002) phase compared with sample in the presence of DEA which preferred to grow in (101) direction. SEM micrograph displays the morphology of ZnO nanocrystalline for both of the samples which shows micron size and non-uniform particles for sample without DEA whereas for sample with DEA exhibit smaller size ({approx}110 nm) and nearly spherical in shape despite of some agglomeration occurs at the interparticle separation. The photoluminescence (PL) spectra shows UV emission peak for both of the samples where sample with the absence of DEA possess lower intensity of UV emission peak compared to samples with DEA which demonstrate stronger intensity despite of having very weak visible secondary emission peak at 530 nm.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Electrical and Surface Morphology of Polyvinylchloride Composites Filled with Aluminum Powder

In this work, the electrical and surface morphology of polyvinyl chloride (PVC) composites filled with different concentration of aluminum powder varying from 0 to 40 wt.% have been prepared by solution costing method. The electrical conductivity of these composites were investigated in the frequency range 100 Hz-10 MHz at room temperature. The conductivity of the composites system exhibited a strong frequency dependence particularly in the vicinity of percolation threshold (20 wt.%). It was observed that the electrical conductivity gradually increased with filler concentration and frequency and explained in terms of hopping conduction mechanism. The electrical conductivity of the composites obeys universal power law (i.e. {sigma} = Af{sup n}), where, n is power exponent. The scanning electron microscope (SEM) micrographs indicate the agglomeration of aluminum particles dispersed within the PVC at the higher aluminum concentration, yielding a conductive path through the composites. It is also corroborated with electrical conductivity result.

36 MATERIALS SCIENCE↗

Multi-photon UV photolysis of gaseous polycyclic aromatic hydrocarbons: Extinction spectra and dynamics

The extinction spectra of static naphthalene and static biphenylene vapor, each buffered with a noble gas at room temperature, were measured as a function of time in the region between 390 and 850 nm after UV multi-photon laser photolysis at 308 nm. Employing incoherent broadband cavity enhanced absorption spectroscopy (IBBCEAS), the spectra were found to be unstructured with a general lack of isolated features suggesting that the extinction was not solely based on absorption but was in fact dominated by scattering from particles formed in the photolysis of the respective polycyclic aromatic hydrocarbon. Following UV multi-photon photolysis, the extinction dynamics of the static (unstirred) closed gas-phase system exhibits extraordinary quasi-periodic and complex oscillations with periods ranging from seconds to many minutes, persisting for up to several hours. Depending on buffer gas type and pressure, several types of dynamical responses could be generated (classified as types I, II, and III). They were studied as a function of temperature and chamber volume for different experimental conditions and possible explanations for the oscillations are discussed. A conclusive model for the observed phenomena has not been established. However, a number of key hypotheses have made based on the measurements in this publication: (a) Following the multi-photon UV photolysis of naphthalene (or biphenylene), particles are formed on a timescale not observable using IBBCEAS. (b) The observed temporal behavior cannot be described on basis of a chemical reaction scheme alone. (c) The pressure dependence of the system's responses is due to transport phenomena of particles in the chamber. (d) The size distribution and the refractive indices of particles are time dependent and evolve on a timescale of minutes to hours. The rate of particle coagulation, involving coalescent growth and particle agglomeration, affects the observed oscillations. (e) The walls of the chamber act as a sink. The wall conditions (which could not be quantitatively characterized) have a profound influence on the dynamics of the system and on its slow return to an equilibrium state.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The precipitation synthesis of broad-spectrum UV absorber nanoceria

In this paper the possibility of nanoceria as broad-spectrum UV absorber was evaluated. Nanoceria were synthesized by precipitation process from cerium nitrate solution and ammonium hydroxide as precipitant agent. Isopropanol was mixed with water as solvent to prevent hard agglomeration. The structure of resulting nanoceria was characterized by x-ray diffractometer (XRD). The transparency in the visible light and efficiency of protection in UV A region were studied using ultraviolet-visible (UV - Vis) spectrophotometer. The results show that nanoceria possess good tranparency in visible light and high UV light absorption. The critical absorption wavelenght of 368 nm was obtained which is desirable for excellent broad-spectrum protection absorbers. Moreover, analysis of photodegradation nanoceria to methylene blue solution shows poor photocatalytic activity. It indicates that nanoceria suitable for used as UV absorber in personal care products.

36 MATERIALS SCIENCE↗

The influence of self-assembly behavior of nanoparticles on the dielectric polymer composites

To clearify the influence of the distribution of the conductive nanoparticles on the dielectric properties of the corresponding polymer composites, the microstructure and dielectric character of the composites based on the oleic acid modified ferroferric oxide and polyvinylidene fluoride (PVDF) polymer have been studied experimentally. It is found that these composites exhibit a normal percolative phase transition over the filler content from insulator to conductor, consistent with the classical percolation theory. However, when the percentage of fillers is at a certain value which is below the percolation threshold, these nanoparticles can assemble into a special porous structure in the PVDF matrix, associated with the enhancement of dielectric constant at low frequency. In addition, the controllable dispersion of conducting nanoparticles in a polymer matrix can prevent premature agglomeration at low filling fractions and avoid the appearance of anomalously early percolation. Therefore, the self-assembly behavior of nanoparticles can be beneficial to preparation of the high dielectric constant and low loss composites for the application of electric energy storage.

36 MATERIALS SCIENCE↗

Double dumbbell shaped AgNi alloy by pulsed electrodeposition

Silver-Nickel is the well-known thermally immiscible system that makes them quite complex for the formation of alloy. This kind of alloy can be attained from electrodeposition method. In the present work, AgNi alloy was synthesized by pulsed electrodeposition in a single bath two electrode system with the use of anodic alumina membrane. The prepared AgNi alloy and pure Ag were characterized with X-ray Diffraction (XRD) for structural confirmation, Scanning Electron Microscopy (SEM) for morphological, and magnetic properties by Vibrating Sample Magnetometer, respectively. The X-ray Diffraction study shows the formation of cubic structure for pure Ag. SEM analysis reveals the double dumbbell morphology for AgNi alloy and spherically agglomeration for pure silver. Hysteresis behaviour from VSM measurement indicates that the AgNi alloy have good ferro-magnetic properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

In situ study on low-k interconnect time-dependent-dielectric-breakdown mechanisms

An in situ transmission-electron-microscopy methodology is developed to observe time-dependent dielectric breakdown (TDDB) in an advanced Cu/ultra-low-k interconnect stack. A test structure, namely a “tip-to-tip” structure, was designed to localize the TDDB degradation in small dielectrics regions. A constant voltage is applied at 25 °C to the “tip-to-tip” structure, while structural changes are observed at nanoscale. Cu nanoparticle formation, agglomeration, and migration processes are observed after dielectric breakdown. The Cu nanoparticles are positively charged, since they move in opposite direction to the electron flow. Measurements of ionic current, using the Triangular-Voltage-Stress method, suggest that Cu migration is not possible before dielectric breakdown, unless the Cu/ultra-low-k interconnect stacks are heated to 200 °C and above.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Study on effect of annealing conditions on structural, magnetic and superconducting properties of MgB{sub 2} bulk samples

Effect of annealing conditions on structural, magnetic and superconducting properties of Magnesium Diboride (MgB{sub 2}) bulk superconductor samples prepared by solid state route method are compared. The samples are made by taking Magnesium and Boron powders in stoichiometric ratio, grounded well and pelletized at pressure of about 10Tonnes. These pellets are annealed in both Argon and vacuum environment separately up to 800°c for two hours. Both the samples show clear superconducting transition at Tc ∼ 38 k. This is further conformed by AC/DC magnetization (M-T), Resistivity [ρ (T, H)] measurements under magnetic field up to 14 Tesla as well. Rietveld refinement of X-ray diffraction of both samples conformed the MgB{sub 2} phase formation with P6/mmm space group symmetry. Scanning Electron Microscopy images of the surface revile more agglomeration of grains in case of Argon annealed samples. This result in more critical current density (J{sub c}) of Argon annealed samples than vacuum annealed one calculated from Bean's critical state model. This high Jc is explained in terms of more inter grain connectivity for Argon annealed sample than vacuum annealed sample.

36 MATERIALS SCIENCE↗

Origin of mechanical modifications in poly (ether ether ketone)/carbon nanotube composite

Variations in the hardness of a poly (ether ether ketone) beam electrically modified with multi-walled carbon nanotubes (MWCNT, 0.5%-3%) are investigated. It is shown that both rupture and hardness variations correlate with the changes in carbon nanotube concentration when using micro indentation and extended Raman imaging. Statistical analysis of the relative spectral intensities in the Raman image is used to estimate local tube concentration and polymer crystallinity. We show that the histogram of the Raman D band across the image provides information about the amount of MWCNTs and the dispersion of MWCNTs in the composite. We speculate that we have observed a local modification of the ordering between pure and modified polymer. This is partially supported by small angle neutron scattering measurements, which indicate that the agglomeration state of the MWCNTs is the same at the concentrations studied.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Phosphine-stabilised Au{sub 9} clusters interacting with titania and silica surfaces: The first evidence for the density of states signature of the support-immobilised cluster

Chemically made, atomically precise phosphine-stabilized clusters Au{sub 9}(PPh{sub 3}){sub 8}(NO{sub 3}){sub 3} were deposited on titania and silica from solutions at various concentrations and the samples heated under vacuum to remove the ligands. Metastable induced electron spectroscopy was used to determine the density of states at the surface, and X-ray photoelectron spectroscopy for analysing the composition of the surface. It was found for the Au{sub 9} cluster deposited on titania that the ligands react with the titania substrate. Based on analysis using the singular value decomposition algorithm, the series of MIE spectra can be described as a linear combination of 3 base spectra that are assigned to the spectra of the substrate, the phosphine ligands on the substrate, and the Au clusters anchored to titania after removal of the ligands. On silica, the Au clusters show significant agglomeration after heat treatment and no interaction of the ligands with the substrate can be identified.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis of mono-dispersed nanofluids using solution plasma

Small-sized and well-dispersed gold nanoparticles (NPs) for nanofluidics have been synthesized by electrical discharge in liquid environment using termed solution plasma processing (SPP). Electrons and the hydrogen radicals are reducing the gold ions to the neutral form in plasma gas phase and liquid phase, respectively. The gold NPs have the smallest diameter of 4.9 nm when the solution temperature was kept at 20 °C. Nucleation and growth theory describe the evolution of the NP diameter right after the reduction reaction in function of the system temperature, NP surface energy, dispersion energy barrier, and nucleation rate. Negative charges on the NPs surface during and after SPP generate repulsive forces among the NPs avoiding their agglomeration in solution. Increasing the average energy in the SPP determines a decrease of the zeta potential and an increase of the NPs diameter. An important enhancement of the thermal conductivity of 9.4% was measured for the synthesized nanofluids containing NPs with the smallest size.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

C{sub 60}-dyad aggregates: Self-organized structures in aqueous solutions

Extensive full-atomistic molecular dynamics simulations are performed to study the self-organization of C{sub 60}-fullerene dyad molecules in water, namely phenyl-C{sub 61}-butyric acid methyl ester and fulleropyrrolidines, which have two elements of ordering, the hydrophobic fullerene cage and the hydrophilic/ionic group. While pristine fullerene or phenyl-C{sub 61}-butyric acid methyl ester forms spherical droplets in order to minimize the surface tension, the amphiphilic nature of charged solute molecules leads to the formation of supramolecular assemblies having cylindrical shape driven by charge repulsion between the ionic groups located on the surface of the aggregates. We show that formation of non-spherical micelles is the geometrical consequence if the fullerene derivatives are considered as surfactants where the ionized groups are only hydrophilic unit. The agglomeration behavior of fullerenes is evaluated by determining sizes of the clusters, solvent accessible surface areas, and shape parameters. By changing the size of the counterions from chloride over iodide to perchlorate we find a thickening of the cylinder-like structures which can be explained by stronger condensation of larger ions and thus partial screening of the charge repulsion on the cluster surface. The reason for the size dependence of counterion condensation is the formation of a stronger hydration shell in case of small ions which in turn are repelled from the fullerene aggregates. Simulations are also in good agreement with the experimentally observed morphologies of decorated C{sub 60}-nanoparticles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗