Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “yield strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Graphene Oxide Nanoribbons for High Early-Strength Cement Concrete

Longitudinal oxidative unzipping of the outer walls of multiwalled carbon nanotubes (MWCNTs) yields graphene oxide nanoribbons (GONRs), which exhibit greater open surface area and functional edge content than MWCNTs. This paper presents a study of the nano-amendment of Portland cement concrete with GONRs in concentrations between 0.05% (in weight of cement, wt%) and 0.0005 wt%, thus up to two orders of magnitude lower than that reported as lower-bound in the archival literature. The dispersibility in aqueous solution as a function of GONR concentration and oxygen weight content (O%) was assessed through dynamic light scattering (DLS) and zeta potential analysis. The results indicated that less effective suspensions were obtained for 0.05 wt% of GONRs and 22.7 O%. Therefore, GONR water suspensions with 30-40% O% were used to manufacture 50 mm × 100 mm cylindrical concrete specimens. After 7 days of curing, results from uniaxial compression tests using four specimens per configuration (MWCNT concentration and O%) showed that the incorporation of GONRs resulted in an average increase in compressive strength up to 45%. Consistent with the DLS and compression test results, SEM micrographs showed well-dispersed GONRs together with accelerated and preferential formation of calcium silicate hydrates (C-S-H) for all GONR concentrations. The results indicate, for the first time, that the incorporation of very small concentrations (as low as 0.0005 wt%) of well-dispersed GONR amendments can significantly enhance the early-age concrete strength. However, such enhancement became insignificant after 28 days of curing.

cement↗
DOE OSTI2024

Polydiallylammonium-Polysulfone Multiblock Copolymers for Moisture-Swing Direct Air Capture of Carbon Dioxide

Polysulfones are an important class of materials for a variety of applications due to their excellent strength and thermal stability. Quaternary ammonium polymers are also useful materials due to their ion exchange properties, and such materials with alkaline counterions have been used to capture carbon dioxide (CO 2 ) from ambient air through a moisture-driven mechanism. Herein, we design sulfone-based multiblock copolymers containing ammonium functionalities and demonstrate their potential for CO 2 capture. Specifically, a series of multiblock copolymers containing both polydiallyldimethylammonium (PDADMA) and polysulfone (PSf) blocks were synthesized. PSf blocks provide mechanical integrity, while the PDADMA blocks enable the direct air capture of CO 2 . Multiblock copolymers were synthesized at high yield, and PDADMA(OH)-PSf copolymer films with good flexibility and strength were formed with IECs of 424 μmol/g (17 mol % PDADMA(OH)), 1407 μmol/g (44 mol % PDADMA(OH)), and 1726 μmol/g (50 mol % PDADMA(OH)). Thermogravimetric analysis was used to determine that all films are thermally stable up to 345 °C. Differential scanning calorimetry revealed that the 17 and 44 mol % functionalized PDADMA(OH)-PSf multiblock copolymers showed one T g at 185 °C and 50 mol % PDADMA(OH)-PSf polymer showed a T g at 183 °C and a second T g at 16 °C. Atomic force microscopy showed that the multiblock polymers exhibit disordered phase separation. Furthermore, the copolymer materials displayed moisture-swing direct air capture of CO 2 , opening up pathways to utilize polymer architecture and chemistry to tailor the properties of promising sorbents.

42 ENGINEERING↗
DOE OSTI2021

Evidence for Higgs boson decays to a low-mass dilepton system and a photon in pp collisions at $\sqrt{s}$ =13 TeV with the ATLAS detector

A search for the Higgs boson decaying into a photon and a pair of electrons or muons with an invariant mass mℓℓ < 30 GeV is presented. The analysis is performed using 139 fb -1 of proton–proton collision data, produced by the LHC at a centre-of-mass energy of 13 TeV and collected by the ATLAS experiment. Evidence for the H → ℓℓγ process is found with a significance of 3.2 over the background-only hypothesis, compared to an expected significance of 2.1 for the Standard Model prediction. The best-fit value of the signal-strength parameter, defined as the ratio of the observed signal yield to the one expected in the Standard Model, is μ=1.5±0.5. The Higgs boson production cross-section times the H → ℓℓγ branching ratio for mℓℓ < 30 GeV is determined to be $8.7_{-2.7}^{+2.8}$ fb.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Signature Analysis Utilizing a Dynamic Molten Salt Reactor Model for MC&A

Moving from traditional fixed fuel nuclear reactor systems to a mobile, dynamic fuel system that has dissolved special nuclear material in a molten salt is a paradigm shift in several respects. One major consideration is how to develop effective nuclear material controls and accounting for these novel reactor systems. The Molten Salt Reactor Experiment is one example of a critical molten salt system and provided a significant reference library based on the documented effort. But it was low thermal power that was not intended to reflect a commercial scale electricity production design. Therefore, to facilitate and assist vendors with domestic licensing considerations, research is underway to identify methods that could be used for domestic safeguards approaches for these novel reactor systems. This research presents the results of a signature analysis of data generated from three simulated scenarios using the molten salt demonstration reactor model defined in the Transient Simulation Framework of Reconfigurable Modules. Each scenario provides 1 hour isotope inventories over a 180 day period. The scenarios investigated provide test cases to examine if direct gamma-ray spectroscopy of the fuel can be used to identify changes comparing a base case (no reactivity control and fixed fission contribution) to an insertion of reactivity (10 pcm no change in fission composition) and a change in fission composition. The analysis demonstrates that monitoring the total count rate in a highly collimated high-resolution photon energy spectrum is sensitive to perturbations imposed into the reactor model. The total photon count rate changes ≈2% for the fission composition change and ≈4.5% for the reactivity insertion compared to the base case. However, both scenarios show an increase in the total photon count rate. The total photon count rate can be used to identify changes due to power (number of fissions) but not due to a change in the material undergoing fission. To distinguish between the two cases of increased power, the photon spectrum would require an intensive analysis technique. A photon peak count rate ratio analysis could be used to identify changes in the fissile material fission generation in the core through identification of a static peak that shows little variation to the source of fission and a highly varying peak. The photon peak strength will ultimately be determined by the isotope’s fission yield. A preliminary analysis investigating the coupling of the isotope’s fission yield and its concentration in the fuel salt derived from the modeling has been performed. A ratio analysis of the photon peak count rates of 140 La to 99 Mo demonstrated that the reactivity insertion creates a distinct difference in the ratio compared to the fission composition change scenario.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

The effect of differential mineral shrinkage on crack formation and network geometry

Rock, concrete, and other engineered materials are often composed of several minerals that change volumetrically in response to variations in the moisture content of the local environment. Such differential shrinkage is caused by varying shrinkage rates between mineral compositions during dehydration. Using both 3D X-ray imaging of geo-architected samples and peridynamic (PD) numerical simulations, we show that the spatial distribution of the clay affects the crack network geometry with distributed clay particles yielding the most complex crack networks and percent damage (99.56%), along with a 60% reduction in material strength. We also demonstrate that crack formation, growth, coalescence, and distribution during dehydration, are controlled by the differential shrinkage rates between a highly shrinkable clay and a homogeneous mortar matrix. Sensitivity tests performed with the PD models show a clay shrinkage parameter of 0.4 yields considerable damage, and reductions in the parameter can result in a significant reduction in fracturing and an increase in material strength. Additionally, isolated clay inclusions induced localized fracturing predominantly due to debonding between the clay and matrix. These insights indicate differential shrinkage is a source of potential failure in natural and engineered barriers used to sequester anthropogenic waste.

58 GEOSCIENCES↗
DOE OSTI2023

A coarse-grained simulation model for colloidal self-assembly via explicit mobile binders

Colloidal particles with mobile binding molecules constitute a powerful platform for probing the physics of self-assembly. Binding molecules are free to diffuse and rearrange on the surface, giving rise to spontaneous control over the number of droplet–droplet bonds, i.e., valence, as a function of the concentration of binders. This type of valence control has been realized experimentally by tuning the interaction strength between DNA-coated emulsion droplets. Optimizing for valence two yields droplet polymer chains, termed ‘colloidomers’, which have recently been used to probe the physics of folding. To understand the underlying self-assembly mechanisms, here we present a coarse-grained molecular dynamics (CGMD) model to study the self-assembly of this class of systems using explicit representations of mobile binding sites. Further, we explore how valence of assembled structures can be tuned through kinetic control in the strong binding limit. More specifically, we optimize experimental control parameters to obtain the highest yield of long linear colloidomer chains. Subsequently tuning the dynamics of binding and unbinding via a temperature-dependent model allows us to observe a heptamer chain collapse into all possible rigid structures, in good agreement with recent folding experiments. Our CGMD platform and dynamic bonding model (implemented as an open-source custom plugin to HOOMD-Blue) reveal the molecular features governing the binding patch size and valence control, and opens the study of pathways in colloidomer folding. This model can therefore guide programmable design in experiments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Magnetized ICF implosions: Scaling of temperature and yield enhancement

This work investigates the impact of an applied magnetic field on the yield and hot-spot temperature of inertial confinement fusion implosions. A scaling of temperature amplification due to magnetization is shown to be in agreement with unperturbed two-dimensional (2D) extended-magnetohydrodynamic simulations. A perfectly spherical hot-spot with an axial magnetic field is predicted to have a maximum temperature amplification of 37%. However, elongation of the hot-spot along field lines raises this value by decreasing the hot-spot surface area along magnetic field lines. A scaling for yield amplification predicts that a magnetic field has the greatest benefit for low-temperature implosions; this is in agreement with simplified 1D simulations, but not 2D simulations where the hot-spot pressure can be significantly reduced by heat-flow anisotropy. Simulations including a P2 drive asymmetry then show that the magnetized yield is a maximum when the capsule drive corrects the hot-spot shape to be round at neutron bang time. An applied magnetic field is also found to be most beneficial for implosions that are more highly perturbed, exceeding the theoretical yield enhancement for symmetric hot-spots. Increasing the magnetic field strength past the value required to magnetize the electrons is beneficial due to the additional suppression of perturbations by magnetic tension.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Utilizing integrated neutron diffraction and elastoplastic self-consistent crystal plasticity model to quantitatively assess the strengthening mechanism in Al–12.5Ce and Al–12.5Ce–0.4Mg alloys

An integrated in-situ neutron diffraction and elastic plastic self-consistent crystal plasticity (EPSC-CP) modeling scheme is performed on a binary Al–12Ce alloy and a ternary Al–12Ce–0.4Mg alloys. Using this scheme, the constitutive parameters, i.e. elastic constants and slip system parameters of individual phases can be calibrated which can be used in microstructure-based CP models to predict materials performance. From this study, it is shown that the elastic constants of Al 11 Ce 3 intermetallics calculated from density function theory calculation in the literature are rather accurate. When applied to the EPSC-CP model, the lattice strains of both the binary and ternary alloys are correctly predicted as compared with experiments, and large lattice strain differences between Al (100) plane and Al 11 Ce 3 (010) plane are demonstrated. The slip system parameters calibrated by the scheme shows that the addition of 0.4 wt% Mg in the alloy has little influence on the critical resolved shear stress of initial dislocation glide in the Al matrix which caused plastic yield in the material. This can be explained by the very dilute Mg solute content in the Al solid solution, causing large spacing of Al–Mg lattice misfit sites and little impact on resistance of dislocation glide at initial yield. The 0.4 wt% Mg addition, on the other hand, has a large influence on the hardening term in the slip system parameters, indicating those Al–Mg misfit sites do help dislocation accumulation during the deformation. The impact of dilute Mg addition on the Al slip system parameters is also reflected in the flow behavior of the ternary alloy: little impact on the yield stress, but a large impact on working hardening and tensile strength of the materials which is consistent with the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Analysis, identification and confirmation of synthetic opioids using chloroformate chemistry: Retrospective detection of fentanyl and acetylfentanyl in urine and plasma samples by EI-GC-MS and HR-LC-MS

Electron Impact Gas Chromatography-Mass Spectrometry (EI-GC-MS) and High Resolution Liquid Chromatography-Mass Spectrometry (HR-LC-MS) have been used in the analysis of products arising from the trichloroethoxycarbonylation of fentanyl and acetylfentanyl in urine and plasma matrices. The method involves the initial extraction of both synthetic opioids separately from the matrices followed by detection of the unique products that arise from their reaction with 2,2,2-trichloroethoxycarbonyl chloride (Troc-Cl), namely Troc-norfentanyl and Troc-noracetylfentanyl. The optimized protocol was successfully evaluated for its efficacy at detecting these species formed from fentanyl and acetylfentanyl when present at low and high levels in urine (fentanyl: 5 and 10 ng/mL and acetylfentanyl: 20 and 100 ng/mL) and plasma (fentanyl: 10 and 20 ng/mL and acetylfentanyl: 50 and 200 ng/mL), values that reflect levels reported in overdose victims. The HR-LC-MS method’s LOQ (limit of quantitation) for the Troc-norfentanyl and Troc-noracetylfentanyl products was determined to be ~10 ng/mL for both species. Even though the superiority in the detection of these species by HR-LC-MS over EI-GC-MS, the latter method proved to be important in the detection of the second product from the reaction, namely 2-phenylethyl chloride that is crucial in the determination of the original opioid. This observation highlights the importance of using complimentary analytical techniques in the analysis of a sample, whether biological or environmental in nature. The method herein serves as a complementary, qualitative confirmation for the presence of a fentanyl in collected urine, plasma and by extension other biological samples amenable to the common extraction procedures described for opioid analysis. More importantly, the method’s main strength comes from its ability to react with unknown fentanyls to yield products that can be not only detected by EI-GC-MS and HR-LC-MS but can then be used to retrospectively identify an unknown fentanyl.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

The nonlinear rheology of complex yield stress foods

Many foods have a yield stress that allows them to retain a desired shape at rest, but transition into a viscous fluid when being served or consumed. The determination of the yield stress of the food dictates how the foods are formed and packaged, how they are served, and how they are perceived when being eaten. Oscillatory shearing provides an ideal test protocol to map the rheology across a range of time and flow strength scales. We couple oscillatory shearing and an iterative recovery procedure to show that the yielding process is a continuous transition for two common yield stress foods. We show that unrecoverable processes from oscillatory tests are equivalent to the steady shear flow behavior. We show that this yielding behavior can be well approximated by a recently published model that treats yield stress materials as continuous viscoelastic fluids with a rate-dependent relaxation time and has parameters that can be obtained from the linear viscoelastic oscillatory frequency sweep and the steady shear flow curve.

Griebler, James J.↗
DOE OSTI2026

An Exploration of the Equation of State Dependence of Core-collapse Supernova Explosion Outcomes and Signatures

We explore, using a state-of-the-art simulation code in 3D and late-enough times to witness final observables, the dependence of core-collapse supernova explosions on the nuclear equation of state (EOS). Going beyond questions of explodability, we compare final explosion energies, nucleosynthetic yields, recoil kicks, and gravitational-wave and neutrino signatures using the SFHo and DD2 nuclear EOSs for a 9 M ⊙ /solar-metallicity progenitor star. The DD2 EOS is stiffer and has a lower effective nucleon mass. The result is a more extended protoneutron star (PNS) and lower central densities. As a consequence, the mean neutrino energies, final explosion energy, and recoil kick speed are lower. Moreover, the evolution of PNS convection differs between the two EOS models in significant ways. This translates in part into interestingly altered neutrino “light” curves and noticeably altered gravitational-wave signal strengths and frequency characteristics that may be diagnostic. The faster exploding model (SFHo) yields slightly more neutron-rich ejecta and more species with atomic weights between 60 and 90 and a weak r-process. However, this is merely a preliminary study. The next step is a more comprehensive and multiprogenitor set of 3D supernova simulations for various EOSs to late times when the observables have asymptoted. Such a future investigation will have a direct bearing on the neutron star and black hole birth mass functions and the quest toward a fully quantitative theory of supernova observables.

Rusakov, Aleksandr [Princeton University, NJ (Unit↗
DOE OSTI2025

Dynamic Strength and Equation of State of Epon 828 and Diethanolamine (DEA) Polymer Epoxy Under Shock Loading

Polymers are increasingly utilized in engineering applications that can experience high loading rates, necessitating increased understanding of their response under such conditions. The tamped Richtmyer-Meshkov Instability (RMI) method was used to characterize the equation of state and dynamic strength of the polymer Epon 828 cured with Diethanolamine (DEA). Plate impact experiments that drove a uniaxial shock compression wave across a sinusoidally corrugated metal-polymer interface were performed to generate shock stresses from 4-12 GPa and strain rates of approximately 1/s in the polymer. X-ray phase contrast imaging recorded the shock motion in the polymer and subsequent interface evolution. Analysis of this data yielded the polymer equation of state and, in conjunction with numerical modeling, the dynamic strength. The equation of state was validated against one-dimensional plate impact experiments from existing literature. The dynamic strength was compared to prior data for Epon 828 and related polymers at lower strain rates and found to exhibit significant strain rate and pressure-hardening effects. The strength of the Epon 828 polymer at 10 6 1/s was found to be approximately 1.5 GPa, suggesting that it is comparable to the strength of high strength metals at these dynamic conditions.

Equation of state↗
DOE OSTI2022

Apparatus for measuring strength in biaxial compression

We report most measurements of compressive strength of ductile materials have involved Hopkinson–Kolsky bars or Taylor anvils placing samples in uniaxial compression. In these geometries, strain is limited by the tendency of the sample to petal, in analogy to necking in uniaxial tension. Estimation of strength for any other form of the stress tensor requires assuming a shape of the yield surface; because data exist only for uniaxial compression, these assumptions are untested. In an imploding spherical shell, compression is biaxial, the plastic strain may not be small, and the material behavior may be nonlinear as a result of work hardening and heating by plastic work. We outline a method of measuring the strengths of materials in biaxial compression, both quasistatically and dynamically, using the compression of thin spherical shells. We suggest surrounding the shell with an annulus filled with a mixture of H 2 and Cl 2 gases whose homogeneous ignition is initiated by a flash of blue and near-ultraviolet light. Less promising approaches are described in Appendixes A–C .

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Influence of silicon infiltration conditions on microstructure and mechanical properties in binder jet 3D printed SiC

Atmosphere, temperature, and hold time were varied for silicon infiltrated binder jet 3D printed SiC preforms. A two-step infiltration process optimized infiltration. The first step at 1450 °C under vacuum facilitated improved wetting. The second step at elevated temperature in argon advanced infiltration while suppressing vaporization. Variation of the second-step temperature (1550–1750 °C) and hold time revealed that 1550 °C for 1 h in argon following initial vacuum treatment yielded the highest silicon uptake ratio (∼96 %) with minimal residual porosity and strengths of 150–180 MPa. Flexural strength was either stable or improved with elevated temperatures up to 1000°C. In contrast, higher temperatures or extended hold times led to increased silicon vaporization and pores. The optimized process was applied to formulations with extra carbon to enhance SiC content and interconnectedness through reaction bonding, which corresponded to increased flexural strength. These findings provide guidance for silicon infiltration in additively manufactured SiC.

Yoon, Bola [ORNL] (ORCID:0000000260875373)↗
DOE OSTI2025

On the functional dependence of transition-potential coupled cluster

Orbital relaxation of the core region is a primary source of error in the computation of core ionization and core excitation energies. Recently, Transition-Potential Coupled Cluster (TP-CC) methods have been used to explicitly treat orbital relaxation using non-variational molecular orbitals determined by reoccupation of orbitals optimized for a fractional core occupation. The amount of fractional occupation is governed by parameter λ, and recommended values for accurate TP-CCSD and XTP-CCSD computations of carbon, nitrogen, oxygen, and fluorine K edges were previously determined. Herein, we explore the performance of several density functionals for generating the fractionally occupied orbitals used in TP-CCSD. These functionals include HF, BP86, BH&HLYP, B3LYP, M06-2X, and ωB97m-V. The fractionally occupied orbitals computed across the various functionals were subsequently employed as the initial orbitals for our TP-CCSD calculations of organic K-edge x-ray absorption and photoelectron spectra. Regardless of the functional used to generate the fractionally occupied orbitals, the TP-CCSD calculations yield accurate and comparable core ionization energies, core excitation energies, and oscillator strengths.

Coupled-cluster methods↗
DOE OSTI2025

Mechanism of shape symmetry breaking in surfactant-mediated crystal growth

We present a dynamical model of crystal growth, in which it is possible to reliably achieve asymmetric products, beginning from symmetric initial conditions and growing within an isotropic environment. The asymmetric growth is the result of a positive feedback mechanism that amplifies the effect of thermal fluctuations in the coverage of surfactants on the growing crystalline facets. Within our simple model, we are able to understand the kinetic and thermodynamic factors involved in both the onset of symmetry breaking and the persistence of anisotropic growth. We demonstrate that the mechanism is general by studying models with increasing complexity. We argue that this mechanism of symmetry breaking underpins observations of colloidal, seed-mediated syntheses of single crystalline metal nanorods capped with strongly interacting surfactants. The parameters within our model are related to experimental observables such as the concentration, hydrophobicity, and binding strength of the surfactants, which suggests a potential route to optimize the yield of asymmetric products in colloidal nanoparticle syntheses.

Oaks-Leaf, Sam↗
DOE OSTI2023

Mechanical Properties of Additively Manufactured 316L Stainless Steel Before and After Neutron Irradiation–FY23

This report presents the observed mechanical behavior of the additively manufactured (AM) 316L stainless steel (SS) before and after neutron irradiation. In the Advanced Materials and Manufacturing Technologies (AMMT) program, a variety of mechanical and physical property data are generated and accumulated to assess the AM austenitic alloy for nuclear reactor applications. The testing and evaluation task in the FY 2023 focused on elucidating the effects of sampling location and build size on the mechanical properties of AM 316L SS (in stress-relieved condition) before and after neutron irradiation. The laser powder bed fusion (LPBF) process produced 316L plates of three distinct sizes from which SS-J3 miniature tensile specimens were machined from six different locations. The tensile specimens were irradiated in the High Flux Isotope Reactor (HFIR) normally to 2 and 10 dpa at the target temperatures of 300 °C and 600 °C. Post-irradiation tensile testing was performed at room temperature, 300 °C, and 600 °C. The mechanical properties of AM 316L SS were significantly influenced by the characteristic microstructures of printed materials, which include fine grains and high-density dislocations. Compared with the traditional 316L SS, AM 316L showed higher initial strength and lower ductility. Regardless of sampling location, the AM 316L steel retained relatively high strength and ductility to the highest irradiation dose. A prompt necking at yield (with little uniform ductility) was observed after irradiation at 300 °C but no embrittlement was observed up to 10 dpa. Ductilization by irradiation–the radiation-induced increase of ductility–was observed for the 600 °C irradiation only and it occurred in low dose range only. The neutron irradiation increased the data variation in many tensile property datasets, particularly after 600 °C irradiation, and no clear dependence of tensile properties on build thickness or sampling location was observed.

36 MATERIALS SCIENCE↗