Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “yield strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

RF AND MECHANICAL DESIGN OF A 915 MHz SRF CAVITY FOR CONDUCTION-COOLED CRYOMODULES

Conduction-cooled SRF niobium cavities are being developed for use in compact, continuous-wave electron linear accelerators for a variety of industrial applications. A 915MHz two-cell cavity has been designed to achieve an energy gain of 3.5 MeV. The design of the cell shape aims at minimizing the peak surface magnetic field. Field flatness is achieved by adjusting the length of the outer end half-cells. The higher-order mode analysis shows that absorbers are not required for a moderate beam current of 5 mA. One of the beam tubes has two side-ports for insertion of coaxial fundamental power couplers. The mechanical design and analysis were done to maintain a stress near or less than 15.5 MPa for all anticipated loading conditions. This is half the measured yield strength and is to provide relief from creep when cavity is evacuated and stored with outside atmospheric pressure.

Ciovati, Gianluigi↗
DOE OSTI2020

Oak Ridge National Laboratory Technical Input for the Nuclear Regulatory Commission Review of the 2017 Edition of ASME Section III, Division 5, ‘High Temperature Reactors’

To assist the Nuclear Regulatory Commission in its decision making on endorsement of the American Society for Mechanical Engineers Boiler and Pressure Vessel Code Section III, Division 5 (2017 Edition) for development of advanced non-light water reactors, the following Division 5 portions were reviewed: Article HBB-2000 Material; Article HCB-2000 Material; Article HGB-2000 Material; Mandatory Appendix HBB-I-14 Tables and Figures; and, Nonmandatory Appendix HBB-U Guidelines for Restricted Material Specifications to Improve Performance in Certain Service Applications. In addition to the 2017 Edition, the same parts of the 2019 Edition have also been reviewed as indicated in various sections of the report. This review was conducted by a collaboration of national laboratory and private sector participants with significant industrial experience, including some heavy lifting and deep diving from Clarus Consulting, LLC., all intended to achieve an objective, independent, and practical perspective. The report provides recommendations, descriptions of the evaluation methods, and the source references for the data used. To build confidence required for endorsement of the Code, this review was conducted as a verification and validation of the above Code contents. The objective of verification is to ensure that the Code is free of error – direct or implied; contains the information needed for its use, including proper coverage of the Code-specified materials for the intended application, and completeness and adequacy of references to other portions of the Code. The objective of validation is to authenticate that the Code tabulations and graphs represent design inputs consistent with what are determined using rules and methods specified by the Code. The authentication process used data that were assembled and/or generated independent of Code development, while the methods of analysis followed Code-specified methods where appropriate. The designated portions for this review cover the five alloys codified for high temperature reactor applications in Division 5, i.e. 316 SS, 304 SS, 800H, 2¼Cr-1Mo, and 9Cr-1Mo-V, regarding their general requirements, permitted specifications and design stress intensity values for pressure-retaining applications, deterioration in service, fatigue acceptance test, permissible weld materials, tensile and yield strength, expected minimum stress-to-rupture values (including for Alloy 718), weld stress rupture factors, permissible materials for bolting use, and restricted specifications in certain service applications. Additionally, stress intensity values for bolting materials including 316 SS, 304 SS and alloy 718 were reviewed. Analysis and discussion are also provided on contents outside of these designated Code portions where it was deemed relevant and necessary to develop a technically sound understanding of issues relating to the designated portions. Due to unavailability of sufficient test data on welds during the review period, the weld stress rupture factors in Tables HBB-I-10.14A to E, which cover a total of ten tables for the five alloys welded with twenty-eight different weld metals (some with similar properties), have been deferred to a future review effort. The review identified mainly two types of issues. The first type includes instances where the Code is found factually incomplete or incorrect, such as obsolete materials specifications listings, missing tabulation of stresses for bolting. Changes to the Code are recommended in these cases. The second type of issue includes instances where the Code tabulations and graphs are found to be less conservative than the review analysis results. In these cases, recommendations are made for further review and consideration where the difference in conservatism exceeds 10%, which is our threshold for questioning technical adequacy, meriting a risk assessment by the Nuclear Regulatory Commission and/or reactor designers. It is noted that this effort has been executed using all available data and established methods of analysis, including methods and criteria specified and used by the Code. As such, the findings that are presented in quantitative detail, in a format for convenient comparison with the Code, and with identification of where further review is recommended, should provide a sound technical basis for decisions about quantifying the implications of the reduced design margins and technical adequacy/inadequacy to form a basis for conditioning specific Code tabulation values on endorsement. Recommendations for specific changes to the Code, however, entail design conservatism considerations beyond the scope of this review effort, and are not made in this report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Impact Response of Cold Spray Deposited Materials

Solid-state cold spraying (CS) of metals and respective blends is becoming increasingly attractive compared to conventional high temperature processes due to the unique properties such as increased yield strength, low ductility, and differences in tensile and compressive strengths that result from microstructural features due to the CS process. Here we report the results of plate impact experiments applied to CS deposits of tantalum (Ta), niobium (Nb), and a tantalum- niobium blend (TaNb). These methods allowed for definition of the Hugoniot for each material type and allowed for assessment of the Hugoniot Elastic Limit (HEL). Scanning electron microscopy was used on recovered samples to characterize the fracture mechanism during spallation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Feedstock Modification for Enhanced Additive Alloys

This project investigated the use of Y 2 O 3 nanoparticles to enhance IN625 feedstock for metal additive manufacturing. The oxide nanoparticles are adhered to the outer surface of the pre-alloyed IN625 powder feedstock, and serve to form an oxide dispersion strengthened (ODS) material in situ during processing. The conventional and enhanced feedstocks were processed using a laser powder bed fusion additive manufacturing (AM) system. The properties of the AM materials were characterized at elevated temperatures and compared to conventional wrought material. The addition of the Y 2 O 3 nanoparticles improved the yield strength, stress rupture, and corrosion properties of the AM material, and compared more favorably with conventional wrought IN625. This research will enable future adoption of additively manufactured ODS-IN625 components with superior properties to current printed IN625 material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

First Annual Report on Development of Microwave Resonant Cavity Transducer for Fluid Flow Sensing: Development of Sensor Performance Model of Microwave Cavity Flow Meter for Advanced Reactor High Temperature Fluids

We are investigating a microwave cavity-based transducer for in-core high-temperature fluid flow sensing in molten salt cooled reactors (MSCR) and sodium fast reactors (SFR). This sensor is a hollow metallic cylindrical cavity, which can be fabricated from stainless steel, and as such is expected to be resilient to radiation, high temperature and corrosive environment of MSCR and SFR. The principle of sensing consists of making one wall of the cylindrical cavity flexible enough so that dynamic pressure, which is proportional to fluid velocity, will cause membrane deflection. Membrane deflection causes cavity volume change, which leads to a shift in the resonant frequency. Feasibility of the sensor was initially investigated with analytical derivations and with COMSOL RF Module computer simulations of resonant frequency spectral shift due to uniform load. We also investigated the mechanical integrity of the flowmeter’s membrane through analytical modelling and COMSOL Structural Mechanics Module computer simulations. Both the analytic model and COMSOL model showed that maximum stresses on the plate, which are at the radial boundary of the plate, are three orders of magnitude smaller than the material’s yield strength and ultimate tensile strength. This indicates that the sensor is at a low risk of mechanical failure. Using results from models, we have developed an initial design for a microwave K-band sensor. A cylindrical resonator prototype was fabricated from brass for the initial tests. The external dimensions of the cavity are matched to the flange of a standard WR-42 waveguide. Microwave field is coupled into the resonant cavity through a subwavelength-size aperture. A test article was developed consisting of a piping Tee with a bulkhead WR-42 microwave waveguide installed in a leak-proof assembly. A microwave waveguide circulator was installed in the setup to suppress the effect of reflections at the cavity entrance by increasing the isolation between the input and the output port. Preliminary spectral characterization of cavity spectral response was performed with a portable PXIe chassis microwave VNA with a custom GUI. Preliminary dry tests of the transducer response were conducted with a set of calibrated weights. Transducer frequency shift was shown to be monotonically increasing with increasing pressure. The next steps will involve investigation of the transducer performance for water flow sensing.

42 ENGINEERING↗
DOE OSTI2022

2021 Report - SRNL Aging and Lifetimes program tritium aging studies on structural alloys

This report documents work performed in fiscal year 2021 at SRNL in support of the Aging and Lifetimes program. This work is part of an on-going collaboration between SRNL and SNL to understand tritium embrittlement of structural metals used in Gas Transfer System reservoirs, thereby informing lifetime assessments and predictions. In this effort, test coupons are pre-charged with tritium and allowed to age in a freezer to minimize tritium diffusion and off-gassing while allowing for born-in helium levels to systematically increase. Coupons are then removed periodically and tested to develop an understanding of how mechanical properties degrade as helium levels increase. This report summarizes test results from coupons which are in various stages of aging as they were tritium pre-charged in previous years. Tests were performed on 304L that was previously tritium pre-charged and allowed to age to nominally 300 appm helium. Specimens from this study were previously tested at 100 appm nominal helium content, and this new test point expands that study. Tensile testing of these heat treated 304L tubes (and welded tubes) aged to 100 appm helium were completed which provided a unique study of a diverse set of microstructures and yield strengths ranging from 200-800 MPa. Additionally, 304L notched and smooth tensile specimens aged to 300 appm helium were tensile tested to predetermined strains to provide for a systematic microscopy investigation of aging effects on microstructural damage in partnership with SNL. Testing was performed on 304L electron beam (EB) weld coupons as well as 21-6-9 annealed coupons that were thermally pre-charged in 2020. Tests on the EB welds were completed at 100 appm helium contents, and tests on the annealed 21-6-9 material were completed at 100, 200, and 300 appm helium. Table 0-1 provides the status of the ongoing tritium coupon aging studies. The table includes the year tritium pre-charging took place, the material, and the targeted helium concentrations (appm) for testing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Irradiated stainless steel 347 and irradiated, welded, and hydrogen charged Zircaloy-4 property data for the target solution vessel and support lines of SHINE

In support of the reactor-vessel development effort of SHINE medical technologies, irradiation of its structural materials and post-irradiation testing have been performed in the High Flux Isotope Reactor at Oak Ridge National Laboratory. This irradiation was performed on welded and unwelded AISI 347 steel and Zircaloy-4 samples at low temperature (~60°C) in contact with the reactor coolant. Hardness, Charpy, and tensile data have been taken from all cases of unirradiated specimens, while post-irradiation tensile and hardness data have been taken from AISI 347 base metal and Zircaloy-4 base metal and weld specimens so far. Additionally, 3-point bend data have been taken from explosion-welded specimens. The expected changes to hardness, yield strength, ultimate tensile strength, uniform elongation, and total elongation as a result of the low temperature and low dose neutron irradiation are reported here.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Impact Response of Control Atmosphere Plasma Spray Deposited Materials

Thermal spray processing of metals and respective blends is becoming increasingly attractive due to the unique properties such as increased yield strength, low ductility, and differences in tensile and compressive strengths that result from microstructural features due to the spray process compared to other additive manufacturing methods. Here we report the results of plate impact experiments applied to Controlled Atmosphere Plasma Spray deposits of tantalum (Ta), niobium (Nb), and a tantalum-niobium blend (TaNb). These methods allowed for definition of the Hugoniot for each material type and the assessment of the Hugoniot Elastic Limit (HEL). Spallation experiments were conducted, and soft recovery of each material type allowed for scanning electron microscopy to characterize the fracture mechanism during tensile loading.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of Processing on Precipitation Kinetics in Nano Polycrystalline 7075 Aluminum Alloy

Fairmount Technologies (FT) seeks to optimize the thermomechanical processing of Aluminum Alloy 7075. The target yield strength is 20% higher than commercially available 7075-T6 temper sheet which will enable structural light weighting by a similar magnitude and reduce the carbon footprint of the transportation sector. To reduce processing cost and make this commercially viable, it is important to understand physical mechanisms driving microstructural changes. A mesoscale phase-field model seeded with experimentally measured microstructures and assessed thermodynamic and kinetic properties will be developed and exercised using HPC at PNNL. It will account for the effect of deformation, temperature, and chemistry on precipitation kinetics in nanocrystalline microstructures. Our objective is to understand this “stress-aging” coupling by performing parametric simulations with mesoscale models for a better understanding of GP zone and η' formation in nanocrystalline 7075 Al. This will help FT optimize processing schedules to achieve desired microstructures that increase both strength and ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Benchmarking Microscale Ductility Measurements (Final Report of the Project DE-NE0008799)

Conventional macroscale experimentation is generally considered to be straightforward with few limitations. Conversely, micro/nanoscale experimentation presents numerous challenges in loading device design, sample preparation and handling, as well as accurate understanding of grain size and local texture effects on recorded measurements. Despite these challenges, nanopillar compression, MEMs based micro-tension, and nanoindentation approaches have been able to provide fundamental contributions to the understanding of material behavior at small lengthscales. However, the overarching shortcoming of these micro/nanoscale experimentation approaches, is the inability to directly translate measurements evaluated at the nm and µm length scales (e.g., hardness) to macroscale tensile material behavior (i.e., elastic modulus, yield strength, and ductility). The objectives of the proposed study are, 1) to establish best practices for obtaining tensile microscale ductility measurements, and 2) to validate methodologies to for comparing microscale ductility measurements to macroscale ductility measurements. In order to achieve these objectives, a multi-lengthscale, multi-temperature testing protocol and simulation framework are executed first on copper as a model material to validate the following approach, and second on reactor grade Zircaloy-2. Experiments are conducted on specimens extracted from the same test piece to ensure nominally identical grain size and texture from specimens to specimen. Motivated by the need to isolate the contribution of size-effects on obtained mechanical property measurements, specimens are manufactured with thicknesses at the micro- (1-10 µm), meso- (10-100's µm), and macroscales (sub-sized ASTM E8). In-situ full-field deformation techniques (scanning electron microscopy (SEM) grid methods and optical DIC) are incorporated into testing at each specimen length-scale to capture plasticity localization and evolution. Experimental testing for all specimens is conducted at both room temperature and elevated temperatures to probe the role of thermal activation on plastic deformation accommodation processes. Simulation efforts focus on examining the mechanical behavior of microscale specimens using a finite element approach with explicitly resolved grain morphologies, and an embedded crystal plasticity model. The cost-efficient implementation method allows for the modeling of a statistically significant number of both real (i.e., digital twin) and generated microstructures to obtain an understanding of the interrelationships between specimen microstructure and geometric variables (grain size, texture, specimen geometry, etc.) on microscale mechanical behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Shear Assisted Processing and Extrusion (ShAPE) of Lightweight Automotive Components (CRADA 418)

Shear Assisted Processing and Extrusion (ShAPE) was developed to manufacture non-circular multicell profiles from secondary aluminum. This was accomplished by integrating a porthole die approach within the rotating ShAPE process. Complexity of the profile geometry was deliberately advanced over the course of the project from round to square, to asymmetric trapezoidal, to two-cell asymmetric trapezoidal. Aluminum alloy 6063 in the form of briquettes (compacted shreddings and engineered machining chips) and castings from pre-consumer industrial scrap were utilized as the feedstock. Tensile properties were shown to exceed the ASTM minimum standard and ASM typical values with the best results reaching yield strength = 247 ± 10 MPa, ultimate tensile strength = 271 ± 10 MPa, and uniform elongation = 16.5 ± 2.4%. These values were achieved for porthole extrusion using unhomogenized castings made from 100% aluminum 6063 industrial scrap. The ability to extrude unhomogenized billet was made possible by in situ conversion of plate-like β-type Fe-rich intermetallics to more extrudable needle-like α-type which is not possible with conventional extrusion. By eliminating the need to dilute iron with primary aluminum during the recycling process, savings of >90% on lifecycle carbon footprint and >50% on embedded energy could ultimately result in lower cost, more environmentally friendly, automotive components.

42 ENGINEERING↗
DOE OSTI2023

Progress Report of Alloy 709 Performance in Liquid Sodium

With improved high-temperature properties, Alloy 709 shows great potential for advanced reactor applications. To understand the effects of sodium on A709, small tensile specimens were machined from two commercial heats and subject to sodium exposure in two forced convection loops operated by Argonne. Thermal aging experiments were also conducted in parallel to isolate any sodium-specific effects. An increasing trend in yield strength and a decrease trend in ultimate tensile strength can be seen with the increasing exposure time, suggesting microstructural changes at these temperatures. Nonetheless, the thermally aged and sodium exposed samples behaved similarly, implying no sodium-specific effect at these temperatures. In contrast, 316H SS exposed to sodium at 650°C showed a strong sodium effect. The different responses of A709 and 316H SS to sodium exposure is of interest and requires additional effort to understand. The cold traps of the sodium loop were replaced early in FY23. During a maintenance operation, an unexpected sodium leak incident occurred at one of the sodium loops, triggering an emergency response. An investigation into the incident revealed that the leak happened at a VCR fitting on the recently replaced cold trap. The metal gasket of the leaked VCR fitting was not compressed sufficiently. A dimensional mismatch between the new component and old piping configuration was responsible for a significant misalignment. A new cold trap with improved design is in production. The new design provides additional flexibility and an access point for post-installation helium leak check and for venting of trapped gas. These design features will make the system more error-tolerant and the installation quality verifiable. A thermodynamic analysis was performed to understand the carburization-decarburization behavior of A709 in sodium environment. The equilibrium carbon activity in the alloy was evaluated with M 23 C 6 , TiC, and NbC. The carburization-decarburization boundary was calculated with different methods developed previously. The results suggests that A709 will be carburized in SMT-1 and SMT-2, and can be decarburized in low-carbon-activity environments such as EBR-II at temperatures above 620-650°C. Nonetheless, A709 should be less likely to be decarburized than 316H SS when exposed to the same low-carbon-activity environment.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Failure Analysis for Molten Salt Thermal Energy Storage Tanks for In-Service CSP Plants

Thermal Energy Storage (TES) is a fundamental component in concentrating solar power (CSP) plants to increase the plant's dispatchability, capacity factor, while reducing the levelized cost of electricity. In central receivers CSP plants, nitrate molten salts have been used for several years for operation temperatures of up to 565 degrees C. Despite many efforts to advance nitrate salt to higher operation temperatures (even considering a replacement with molten chloride salts) to achieve higher energy conversion efficiencies, the 565 degrees C temperature is currently considered the state-of-the art. Although molten salt tanks have been broadly deployed in commercial CSP plants worldwide, several failures have been reported in these tanks after a few months or years of operation, causing significant economic loss and mistrust in CSP technologies. Most of these failures are associated with the infancy of the technology and multiple issues related to tank design, fabrication, commissioning, and aggressive operation. A technical standard dedicated to the design and fabrication of molten nitrate TES tanks does not exist today. Current in-service molten salt tanks have been generally designed based on the American Petroleum Institute's (API) 650 and ASME Section II standards. The API 650 code provides guidelines for dimensions and fabrication for oil storage tanks up to 260 degrees C. The ASME standard provides allowable stress values for various materials at a range of temperatures and conditions. Both standards seem to be limited for molten salt TES tanks where high temperatures, thermal cycling, and transient conditions are expected. In 2020, NREL released the Concentrating Solar Power Best Practices Study (NREL/TP-5500-75763) that summarized multiple issues in CSP plants, along with potential alternatives and recommendations to address those issues based on information collected from participants representing about 80% of operating CSP plants in the world. One of the recommendations from this study was the development of accurate and validated models to evaluate the plant's transient operation, capable of capturing the effect of short-term clouds and operator response, while being flexible in being adapted to various spatial and temporal resource data. The "Failure Analysis for Molten Salt Thermal Energy Tanks for In-Service CSP Plants" project was inspired on this recommendation and was focused on (1) the development and validation of a physics-based model for a representative, commercial-scale molten salt tank, (2) performing simulations to evaluate the behavior of the tank as a function of typical plant operation conditions, (3) understanding tank failures mechanisms, (4) determining the residual stress and distortion in the tank floor after welding fabrication and evaluating their impact in the stresses developed in the tank during operation, (5) assessing the impact of key operation parameters on the temperature and stress distribution, (6) conduct a preliminary evaluation of design features to reduce stress and improve tank's reliability, and (7) estimate the tank's service life based on the stress developed under diverse operation scenarios. From the analysis conducted in the project and presented in this report, it was found that maximum stresses surpassing the yield strength point of the stainless steel (SS) 347H are developed on the tank floor near the perimeter. These large stresses are strongly influenced by the initial residual stresses and distortion of the tank floor after welding fabrication. During operation, large stresses are developed in the tank floor at high operation temperatures with large salt inventory levels during transient operation. High stresses are also related to elevated temperature gradients in the tank floor that could be attributed to insufficient mixing within the salt inflow and the salt inventory. Based on the analysis, creep is the predominant failure mechanism. However, the large stress levels could favor the plastic deformation into buckles, and crack formation due to stress relaxation cracking during cycle operation. A lifetime below 3 years was estimated for the typical plant operation conditions and a specific initial residual stress and deformation distribution of the tank floor. The estimated life agrees with the service time to failure reported in several commercial molten salt tanks. Desing and operation guidelines can be extracted from the analysis presented in this report, which could be adopted by tank manufacturers and CSP operators to advance toward an ultimate solution for tank failures by reducing residual and operational stresses to achieve a tank service life of more than 30 years. Addressing failures in molten salt TES tanks is fundamental for the CSP industry's survivability, but it is also important for other industrial and power generation applications using this technology, including nuclear and concentrating solar thermal.

14 SOLAR ENERGY↗
DOE OSTI2024

Surface Modified Fly Ash for Value Added Products (SuMo Fly Ash)

The objective of this project is to develop a technology to encapsulate coal fly ash particles in sulfurized vegetable oil, enhancing physical and mechanical properties of the fly ash as a filler material when applied in commercial products. This project significantly advances the knowledge base and technology for synthesizing coated fly ash particles for application in different polymer matrices to increase cross-linking, compatibility, air-entrainment and to decrease the leaching potential of metals of concern. Specifically, the project focuses on (a) collection, and characterization of fly ash material from coal power plants; (b) development of Sulfurized Vegetable Oil (SVO) modified (SuMo) fly ash and their detailed characterization; (c) evaluation of the mechanical properties of the SuMo fly ash incorporated plastic and rubber composites for potential replacement of CaCO 3 or carbon black as filler materials with SuMo fly ash in plastic and rubber composites; (d) leaching potential of SuMo fly ash and SuMo fly ash-incorporated plastic and rubber composites to determine the rate of release of trace metals. The major findings of this project are: i) Sulfurized Vegetable Oil coated fly ash (SuMo fly ash) was successfully prepared with a particle size of ≤ 45 micron which exhibited hydrophobicity of contact angle > 90°; ii) the coating reduces leaching of metals (e.g., B, Cr) from fly ash when exposed to water; iii) incorporation of SuMo fly ash increases thermal stability and yield strength of plastics; iv) SuMo coating helps disperse fly ash particles into cured rubbers, natural rubber; (v) SuMo fly ash-incorporated plastic/cured rubbers compounds protects against leaching of toxic elements.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

MARVEL Reactor Fuel Performance Report (Rev.2)

The Microreactor Applications Research Validation and EvaLuation (MARVEL) project is producing a high temperature liquid metal-cooled nuclear test bed at Idaho National Laboratory (INL) to ultimately improve the integration of microreactors to end-user applications. This ambitious effort seeks to design, authorize, construct, test, and operate the reactor within five years. In order to construct and operate the MARVEL reactor in a timely manner, the system will utilize materials and component designs which have already been used, qualified, or licensed from previous reactors. The MARVEL reactor will be located at the INL Transient Reactor Test (TREAT) facility in the north high-bay equipment pit and will use the existing 304 stainless steel-clad U-ZrH1.6 pin-type fuel system developed by General Atomics and purchased from TRIGA International. This fuel has been previously qualified under the United States Department of Energy’s (US DOE) Reduced Enrichment for Research and Test Reactors (RERTR) Program. Even though the regulator of the MARVEL reactor is the US DOE, the standards and overall approach recommended by the Nuclear Regulatory Commission is well-defined and utilized here. Following NUREG-1537 regulatory guidance, this report documents the authorization case for the MARVEL fuel system’s application to MARVEL and establishes stable and predictable fuel performance during the most thermophysically unfavorable conditions achievable in the MARVEL reactor. To that end, this report provides a comprehensive survey of the known thermophysical properties, performance, and quantitative relationships associated with the MARVEL reactor fuel element and uses this information to determine its mechanical integrity and risk of reaching unacceptable conditions during the most extreme accident scenarios predicted for the reactor using the most conservative assumptions available. The information contained herein is compiled from a combination of historical reports and peer reviewed scientific publication manuscripts. Known mechanisms under which the fuel is susceptible to failure are highlighted and compared to conditions that could exist in the MARVEL reactor during an unanticipated transient or accident scenario. The two scenarios considered for analysis in this report are (1) an unprotected loss of flow accident and (2) a hypothetical unprotected loss of coolant accident during the loss of flow accident. Preliminary 2D steady-state analyses herein indicate that both fuel-cladding chemical interactions and fuel-cladding mechanical interactions are negligible throughout the fuel’s operational cycle under both normal and high temperature accident scenario conditions. Although higher fidelity 3D time-dependent modeling and simulations are planned, the following may be concluded presently. The MARVEL fuel element maintains its geometric stability and structural integrity during the most extreme accident scenarios predicted for the MARVEL reactor. The hoop stress during the unprotected loss of flow accident reaches about -1.27 MPa; this negative stress indicates that it is compressive rather than tensile. The compressive stress is a result of the NaK pressure on the outside of the fuel element, caused by the restricted thermal expansion of the NaK coolant, exceeding the internal pressures generated inside of the fuel element. The hoop stress generated in the cladding during the unprotected loss of coolant accident reaches a maximum of about approximately 10 MPa, which is nearly an order of magnitude less than the predicted yield strength of the cladding under high-temperature accident scenario conditions. Calculations were compared with results from high performance computational simulations using BISON and are in very close agreement. A conservative MARVEL fuel meat peak temperature limit of 900 °C is recommended presently, which is about 180 °C higher than the peak fuel temperature predicted to occur during the most extreme accident. Based on the known properties and behavior of the MARVEL fuel element, the fuel successfully meets its design and safety requirements under normal and most extreme accident conditions with a large safety margin.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

RF and Mechanical Design of a 915 MHz SRF Cavity for Conduction-Cooled Cryomodules

Conduction-cooled SRF niobium cavities are being developed for use in compact, continuous-wave electron linear accelerators for a variety of industrial applications. A 915 MHz two-cell cavity has been designed to achieve an energy gain of 3.5 MeV. The design of the cell shape aims at minimizing the peak surface magnetic field. Field flatness is achieved by adjusting the length of the outer end half-cells. The higher-order mode analysis shows that absorbers are not required for a moderate beam current of 5 mA. One of the beam tubes has two side-ports for insertion of coaxial fundamental power couplers. The mechanical design and analysis were done to maintain a stress near or less than 15.5 MPa for all anticipated loading conditions. This is half the measured yield strength and is to provide relief from creep when cavity is evacuated and stored with outside atmospheric pressure.

Ciovati, Gianluigi↗
DOE OSTI2025

Understanding Geometry and Microstructure Interactions In LPBF By Linking Lab Scale Studies To Real Part Case Examples

The mechanical properties derived from simple tensile tests are uniquely important in the design and qualification of load bearing metallic components. The tensile properties in standards for wrought metallic materials are generally accessible for design and simulation engineers, but this is not the case for additively manufactured metals. This work investigates the influence of tensile specimen geometry on the mechanical properties of laser powder bed fusion (LPBF) additively manufactured Ti-6Al-4V, particularly in relation to properties measured from specimens excised from an exemplar part. A comprehensive analysis was conducted across various specimen geometries, considering factors such as thermal history, cross-sectional area, shape, and surface roughness. Key findings reveal that sample size, particularly cross-sectional area, significantly affects reported tensile properties, with ASTM E8 flat and round specimens exhibiting differences in elastic modulus (13%), yield strength (17%), ultimate tensile strength (UTS) (14%), and elongation to failure (11%). Additionally, surface roughness was found to have a limited impact on ASTM round geometries, but it becomes critical in thin-walled and small high-throughput samples. The ASTM flat samples closely matched the properties of samples excised from the exemplar part, underscoring the necessity of testing witness samples that accurately represent end-use conditions. Furthermore, mechanical properties of samples built within the stitch zone of the exemplar part demonstrated reduced ductility, highlighting the importance of laser alignment and qualification in multi-laser additive manufacturing processes. Overall, this study emphasizes the need for careful consideration of specimen geometry and testing conditions to ensure accurate reporting of mechanical properties in LPBF Ti-6Al-4V.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Let’s Stick Together: Interplay of Moisture, Particle Size, and Anatomical Fraction in the Flowability of Corn Stover Crumbles

Handling of agricultural waste biomass feedstocks (such as corn stover) is a persistent challenge in the production of biofuels and chemicals at integrated biorefineries. Inconsistent flowability and high feedstock variability creates equipment downtime and processing challenges. This work investigates the influence of anatomical fractionation and moisture content on the bulk solids handling behavior of corn stover crumbles. A combination of rotational shear testing, tribological measurements, and surface and sorption characterization techniques (inverse gas chromatography (IGC), dynamic vapor sorption (DVS), and electron microscopy) were used to evaluate the contributions of particle composition, size, and surface properties to flow behavior. Shear and frictional testing revealed that moisture content has the greatest effect on flowability, significantly increasing unconfined yield strength (ƒ c ) and reducing the flow function coefficient (F F C), regardless of anatomical fraction. While differences in surface energy were observed between fractions, particularly in polar contributions (γ AB ), these did not correspond to meaningful differences in flow behavior. Coarser 6 mm particles exhibited poorer flow performance than 4 mm crumbles, likely due to broader particle size distributions and increased particle interlocking. Taken together, these results suggest that anatomical fractionation provides minimal benefit from a bulk handling perspective. Moisture content and particle size heterogeneity dominate handling behavior, reinforcing the utility of unfractionated corn stover in processing environments. These insights can inform the design of more efficient and reliable feedstock processing systems for agricultural biomass in integrated biorefineries.

09 BIOMASS FUELS↗