Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thin contacts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Perovskite Quantum Dot Solar Cells: Mapping Interfacial Energetics for Improving Charge Separation

Colloidal halide perovskite nanocrystals or quantum dots (QDs) show similar defect tolerance as thin film perovskite materials with added nanoscale phenomena. Perovskite QD solar cells have demonstrated efficiencies of 16.6%, greater than that of any other QD material system. While the efficiency lags behind the best thin-film perovskite devices, these solar cells could have advantages over the thin-film versions in terms of processability, phase stability, and high open-circuit voltages. However, some operating principles behind perovskite quantum dot device stacks and the associated electric field properties are still unknown. Here, we characterize the junction structure within perovskite QD solar cells, by exposing functioning cross-sections and using nanometer-scale Kelvin probe force microscopy to offer insight into the selection and performance of charge selective contacts. We also evaluated various solar cell device architectures with different selective contacts to isolate the role of each junction in device performance. We show that in high-performance n-i-p architectures, both electron- and hole-transport layer (HTL) interfaces possess a strong electric field, but in the case of the inverted p-i-n architecture, we find that high interfacial recombination at the HTL/QD junction is responsible for subpar device performance. Perovskite QD and thin film materials can synergistically be combined to offer more design flexibility in PV devices, and here we demonstrate that the interface between perovskite thin films and QDs are relatively benign and amenable for synergistic device design.

14 SOLAR ENERGY↗
DOE OSTI2022

All‐Printed Ultrahigh‐Responsivity MoS 2 Nanosheet Photodetectors Enabled by Megasonic Exfoliation

Abstract Printed 2D materials, derived from solution‐processed inks, offer scalable and cost‐effective routes to mechanically flexible optoelectronics. With micrometer‐scale control and broad processing latitude, aerosol‐jet printing (AJP) is of particular interest for all‐printed circuits and systems. Here, AJP is utilized to achieve ultrahigh‐responsivity photodetectors consisting of well‐aligned, percolating networks of semiconducting MoS 2 nanosheets and graphene electrodes on flexible polyimide substrates. Ultrathin (≈1.2 nm thick) and high‐aspect‐ratio (≈1 μm lateral size) MoS 2 nanosheets are obtained by electrochemical intercalation followed by megasonic atomization during AJP, which not only aerosolizes the inks but also further exfoliates the nanosheets. The incorporation of the high‐boiling‐point solvent terpineol into the MoS 2 ink is critical for achieving a highly aligned and flat thin‐film morphology following AJP as confirmed by grazing‐incidence wide‐angle X‐ray scattering and atomic force microscopy. Following AJP, curing is achieved with photonic annealing, which yields quasi‐ohmic contacts and photoactive channels with responsivities exceeding 10 3 A W −1 that outperform previously reported all‐printed visible‐light photodetectors by over three orders of magnitude. Megasonic exfoliation coupled with properly designed AJP ink formulations enables the superlative optoelectronic properties of ultrathin MoS 2 nanosheets to be preserved and exploited for the scalable additive manufacturing of mechanically flexible optoelectronics.

2D materials↗
DOE OSTI2025

Productivity and cost of energy chipping with non-integrated harvesting systems in the Coastal Plain of the US south

Research from the 1980s–2010s suggested that integrated harvesting systems that harvest conventional products (e.g., sawtimber, pulpwood) and energy chips simultaneously were the most effective solution to produce energy chips in the US South. Alternatives, such as biomass-only systems, have important advantages in forest stands with low volumes of merchantable timber. The goal of this study was to estimate the productivity and cost of producing energy chips using non-integrated systems. Innovative chipping contractors using non-integrated systems were identified through contacts with procurement foresters responsible for purchasing energy chips. Elemental time-and-motion studies were conducted to estimate harvesting productivity on five operations, including one clearcut harvest and four first thinnings in overstocked stands. The hourly cost of equipment was estimated using the machine rate method. Cost per tonne was estimated by combining hourly productivity and hourly costs in a modified version of the Auburn Harvesting Analyzer. System productivity averaged 37 tonnes per scheduled machine hour (smh) and cut-and-haul costs averaged $33.86 t −1 (USD), which was comparable to previous estimates from integrated systems. In conclusion, this study suggests there are viable alternatives to integrated harvesting systems to produce energy chips, especially in stands with low volumes of merchantable timber.

09 BIOMASS FUELS↗
DOE OSTI2022

Thermal analysis of RHIC arc dipole magnet cold mass with EIC beam screen

The existing RHIC storage rings – including their superconducting magnet arcs – will be used for the hadron storage ring of the Electron-Ion Collider (EIC). The vacuum chamber of these magnets was not designed for the EIC hadron beams, with shorter bunches and of higher average current than the RHIC beams. With the current stainless steel beam pipe, the resistive-wall (RW) heating will exceed the dynamic heat load budget. Limiting the RW heating is important to prevent the superconducting magnets from quenching and to maintain a low screen temperature necessary to impede the rise of RW heating (higher resistance at higher temperature) as well as to achieve desired ultra-high vacuum. In addition, simulations predict the formation of electron cloud which would further contribute to the dynamic heat load and could compromise the quality and stability of the beam. To reduce the resistive-wall heating and suppress electron cloud, a beam screen will be installed in the vacuum chamber of the RHIC SC magnets. The screen will have a high RRR copper layer at its inner face – useful to reduce the resistive-wall impedance thanks to its high conductivity especially at cryogenic temperatures – and will be coated with a thin layer of amorphous carbon, a material with low secondary electron yield to suppress the formation of electron clouds. The baseline solution envisages a screen that will be cooled by thermal contact to the 4.55 K beam pipe. Detailed thermal analysis have been conducted in ANSYS 2020 for an arc dipole cold mass equipped with a beam screen in order to study the feasibility of a passively-cooled screen and guide its design. Temperature-dependent thermal conductivity properties of all materials in the operating (cryogenic) temperature range are considered. Suitable assumptions and simplifications are made to model the magnet coil and calculate its homogenized thermal conductivity. Sensitivity studies with respect to layer thicknesses and area of contact are carried out and results are presented.

43 PARTICLE ACCELERATORS↗
NASA NTRS1975

Ovonic type switching in tin selenide thin films

Amorphous tin selenide thin films which possess Ovonic type switching properties are fabricated using vacuum deposition techniques. The devices are fabricated in a planar configuration and consist of amorphous tin selenide deposited over silver contacts. Results obtained indicate that Ovonic type memory switching does occur in these films with the energy density required for switching from a high impedance to a low impedance state being dependent on the spacing between the electrodes of the device. There is also a strong implication that the switching is a function of the magnitude of the applied voltage pulse.

Baxter, C. R.↗
NASA NTRS1979

High temperature - low mass solar blanket

Interconnect materials and designs for use with ultrathin silicon solar cells are discussed, as well as the results of an investigation of the applicability of parallel-gap resistance welding for interconnecting these cells. Data relating contact pull strength and cell electrical degradation to variations in welding parameters such as time, voltage and pressure are presented. Methods for bonding ultrathin cells to flexible substances and for bonding thin (75 micrometers) covers to these cells are described. Also, factors influencing fabrication yield and approaches for increasing yield are discussed. The results of vacuum thermal cycling and thermal soak tests on prototype ultrathin cell test coupons and one solar module blanket are presented.

Mesch, H. G.↗
NASA NTRS1980

Lubrication and wear mechanisms of polyimide-bonded graphite fluoride films subjected to low contact stress

The tribological properties of polyimide-bonded graphite fluoride films were studied with a pin-on-disk friction apparatus. A 440 C HT stainless steel rider with a 0.95 millimeter diameter flat area was slid against the film in order to achieve a light, closely controlled contact stress. A 1 kilogram load was applied to this flat to give a projected contact stress of 14 megapascals. Two stages of lubrication were operating. In the first stage, the film supported the load and the lubricating mechanism appeared to be the shear of a thin surface layer of the film between the rider and the bulk of the film. The second stage began after the original film was worn away, and the lubricating mechanism appeared to be the shear of very thin lubricant layers between the flat area on the rider and flat plateaus generated on the sandblasted asperities of the metallic substrate. The major difference between the lubricating mechanisms of the hemispherical and flat riders was that the flat wore through the film much more slowly than did the hemisphere.

Fusaro, R. L.↗
NASA NTRS1983

New method of determining the onset of ring cracking

A technique is developed for the detection of the onset of circumferential ring cracks in a flat brittle piece of an electrically insulating material. Thin metal films were deposited on both the insulating indentor (diamond) and the insulating brittle flat. The initiation of a ring crack was signified by a step in the monitored electrical contact resistance between the indentor and flat metal films versus the applied force. It was determined by tests performed on polished glass slides using diamond indentors that this technique is both sensitive and reproducible. The onset of crack formation as observed by optical means was found to occur at the same time as the step in the contact resistance when both experiments were carried out simultaneously.

Grzybowski, T. A.↗
NASA NTRS1990

Kinetics and transport at AMTEC electrodes. II - Temperature dependence of the interfacial impedance of Na(g)/porous Mo/Na-Beta-double prime alumina

The exchange current, transfer coefficient, mass-transport parameters, and electrode capacitance at the Na(g)/porous Mo/Na-Beta-double prime alumina solid electrolyte (BASE) phase boundary have been evaluated from 740 to 1220 K. The transfer coefficient exhibits a value close to 0.5 and the exchange current is dominated by collision frequency, with no significant activation energy. Since the porous Mp-electrode adopts a fairly regular microstructure on the BASE surface, the magnitude of the exchange current of mature electrodes directly depends on the actual contact zone of the porous metal film with the BASE ceramic, and decreases slightly as grain growth occurs. The exchange currents and the mass-transport parameters derived for very porous, thin Mo electrodes indicate that the charge-transfer reaction occurs at a small fraction of the interface. High-frequency limiting capacitance and resistance values due to the interface show potential dependence and a value on the order of 1 F/sq m and 0.1-1.0 Ohm-sq cm.

Williams, R. M.↗
NASA NTRS2003

Morphology of the Vestibular Utricule in Toadfish, Opsanus Tau

The uticle is an otolith organ in the vertebrate inner ear that provides gravitoinertial acceleration information into the vestibular reflex pathways. The aim of the present study was to provide an anatomical description of this structure in the adult oyster toadfish, and establish a morphological basis for interpretation of subsequent functional studies. Light, scanning electron and transmission electron microscopy were applied to visualize the sensory epithelium and its neural innervation. Electrophysiological techniques were used to identify utricular afferents by their response to translation stimuli. Similar to nerve afferents supplying the semicircular canals and lagena, utricular afferents commonly exhibit a short-latency increase of firing rate in response to electrical activation of the central efferent pathway. Afferents were labeled with biocytin either intraaxonally or with extracellular bulk deposits. Light microscope images of serial thick sections were used to make three-dimensional reconstructions of individual labeled afferents to identify the dendritic morphology with respect to epithelial location. Scanning electron microscopy was used to visualize the surface of the otolith mass facing the otolith membrane, and the hair cell polarization patterns of strioler and extrastriolar regions. Transmission electron micrographs of serial thin sections were compiled to create a three-dimensional reconstruction of the labeled afferent over a segment of its dendritic field and to examine the hair cell-afferent synaptic contacts.

Bass, L.↗
NASA NTRS2003

A 2-D Piston Effect Solution for the Relaxation in the MISTE Cell

When a large density stratification is no longer a problem in a microgravity environment, one would like to increase the sample size in order to increase the signal-to-noise ratio for a specific heat measurement. To reduce the equilibration time associated with the large sample size, we designed a cylindrical cell containing a stack of plates that separate the bulk fluid into 60 equally thin layers. To understand the thermal behavior of the whole cell, we analyzed the thermal behavior of a 2-D composite system of a cylindrical near-critical fluid layer in contact with a cylindrical copper plate. In this 2-D analysis, the circumference boundary of the two cylindrical layers is subjected to a step temperature change. The solution of this 2-D composite system includes the piston effect that speeds up the equilibration in the near-critical fluid layer and the pure diffusion in the copper plate. The results of this analysis indicate that the characteristic length for the equilibration of the stacked cell is determined by an effective thickness of a single fluid layer instead of the total height of the cylindrical cell.

Weilert, Mark↗
NASA NTRS2004

Chirped-Superlattice, Blocked-Intersubband QWIP

An Al(x)Ga(1-x)As/GaAs quantum-well infrared photodetector (QWIP) of the blocked-intersubband-detector (BID) type, now undergoing development, features a chirped (that is, aperiodic) superlattice. The purpose of the chirped superlattice is to increase the quantum efficiency of the device. A somewhat lengthy background discussion is necessary to give meaning to a brief description of the present developmental QWIP. A BID QWIP was described in "MQW Based Block Intersubband Detector for Low-Background Operation" (NPO-21073), NASA Tech Briefs Vol. 25, No. 7 (July 2001), page 46. To recapitulate: The BID design was conceived in response to the deleterious effects of operation of a QWIP at low temperature under low background radiation. These effects can be summarized as a buildup of space charge and an associated high impedance and diminution of responsivity with increasing modulation frequency. The BID design, which reduces these deleterious effects, calls for a heavily doped multiple-quantum-well (MQW) emitter section with barriers that are thinner than in prior MQW devices. The thinning of the barriers results in a large overlap of sublevel wave functions, thereby creating a miniband. Because of sequential resonant quantum-mechanical tunneling of electrons from the negative ohmic contact to and between wells, any space charge is quickly neutralized. At the same time, what would otherwise be a large component of dark current attributable to tunneling current through the whole device is suppressed by placing a relatively thick, undoped, impurity-free AlxGa1 x As blocking barrier layer between the MQW emitter section and the positive ohmic contact. [This layer is similar to the thick, undoped Al(x)Ga(1-x)As layers used in photodetectors of the blocked-impurity-band (BIB) type.] Notwithstanding the aforementioned advantage afforded by the BID design, the responsivity of a BID QWIP is very low because of low collection efficiency, which, in turn, is a result of low electrostatic- potential drop across the superlattice emitter. Because the emitter must be electrically conductive to prevent the buildup of space charge in depleted quantum wells, most of the externally applied bias voltage drop occurs across the blocking-barrier layer. This completes the background discussion. In the developmental QWIP, the periodic superlattice of the prior BID design is to be replaced with the chirped superlattice, which is expected to provide a built-in electric field. As a result, the efficiency of collection of photoexcited charge carriers (and, hence, the net quantum efficiency and thus responsivity) should increase significantly.

Gunapala, Sarath↗
NASA NTRS2001

Heavy ion induced soft breakdown of thin gate oxides

Heavy ion induced soft and hard breakdown are investigated in thin gate oxides as a function of LET, fluence, and voltage applied during irradiation. It is found that post-irradiation oxide conduction is well described by the Sune quantum point contact model.

radiation↗
NASA NTRS2003

Energy-Absorbing, Lightweight Wheels

Improved energy-absorbing wheels are under development for use on special-purpose vehicles that must traverse rough terrain under conditions (e.g., extreme cold) in which rubber pneumatic tires would fail. The designs of these wheels differ from those of prior non-pneumatic energy-absorbing wheels in ways that result in lighter weights and more effective reduction of stresses generated by ground/wheel contact forces. These wheels could be made of metals and/or composite materials to withstand the expected extreme operating conditions. As shown in the figure, a wheel according to this concept would include an isogrid tire connected to a hub via spring rods. The isogrid tire would be a stiff, lightweight structure typically made of aluminum. The isogrid aspect of the structure would both impart stiffness and act as a traction surface. The hub would be a thin-walled body of revolution having a simple or compound conical or other shape chosen for structural efficiency. The spring rods would absorb energy and partially isolate the hub and the supported vehicle from impact loads. The general spring-rod configuration shown in the figure was chosen because it would distribute contact and impact loads nearly evenly around the periphery of the hub, thereby helping to protect the hub against damage that would otherwise be caused by large loads concentrated onto small portions of the hub.

Waydo, Peter↗
DOE OSTI2020

Design, Optimization, and In-Depth Understanding of Front and Rear Junction Screen-Printed Double-Side Passivated Contacts Solar Cells

In this work, detailed numerical modeling is performed for front junction (FJ) and rear junction (RJ) n-type Si solar cells with screen-printed double-side poly-Si based tunnel oxide passivated contacts (TOPCon). Fundamental understanding of both structures is crucial to explore factors that limit the efficiency potential of the two designs. By investigating several key parameters such as front poly sheet resistance and thickness, bulk material properties, and carrier transport in our simulation model, we determine and explain why RJ cells outperform FJ cells. Our findings reveal that FJ suffers from present technological limitations of p-poly based passivated contacts, namely, i) large recombination observed in textured p-TOPCon emitter and ii) low solid solubility and hole mobility in boron-doped poly-Si resulting in very high sheet resistance of front p-poly layers which must be made thin to reduce absorption losses. In contrast, RJ desensitized the cell efficiency to front sheet resistance allowing application of ultra-thin front n-poly layers and is therefore ideally suited for double-side TOPCon cells. Lastly, we have developed a roadmap for efficiency projections of commercial-type screen-printed RJ and FJ topologies reaching ~24% and >22.5% efficiencies respectively, quantifying and explaining the impact of technological innovations on the performance of each design.

14 SOLAR ENERGY↗
DOE OSTI2020

Photonic curing of solution-deposited ZrO 2 dielectric on PEN: a path towards high-throughput processing of oxide electronics

High-throughput manufacturing of oxide electronics will enable new applications ranging from large-area displays to flexible medical devices and low-cost solar panels. However, high quality oxide films from solution-based precursors typically require 20 minutes or more of thermal annealing at high temperature (> 250 °C) for each layer, severely limiting both the throughput and substrate choice. Here, we report high speed photonic curing of ZrO 2 dielectric thin films on flexible plastic substrates. The curing and patterning processes can be achieved simultaneously by using shadow mask patterning or adjusting conditions to convert oxide only on top of underlying metal contacts, i.e. self-aligned patterning. Metal-insulator-metal capacitors using two layers of ZrO 2 films photonically cured in just 100 seconds per layer show non-dispersive capacitance-frequency behavior from 10 2 to 10 6 Hz, high areal capacitance of 200 nF/cm 2 and low dissipation factor of 0.03 at 10 5 Hz, leakage current density of ~ 10 -7 A/cm 2 at an applied field of 2 MV/cm, and a breakdown field of nearly 8 MV/cm. Using an upgraded tool, similar dielectric properties are achieved in as short as 100 milliseconds using a single pulse of light, revealing a pathway to oxide film processing beyond 30 m/min.

14 SOLAR ENERGY↗
NASA NTRS1977

A lightweight solar array study

A sample module was assembled to model a portion of a flexible extendable solar array, a type that promises to become the next generation of solar array design. The resulting study of this module is intended to provide technical support to the array designer for lightweight component selection, specifications, and tests. Selected from available lightweight components were 127-micron-thick wrap-around contacted solar cells, 34- micron-thick sputtered glass covers, and as a substrate a 13-micron-thick polyimide film clad with a copper printed circuit. Each component displayed weaknesses. The thin solar cells had excessive breakage losses. Sputtered glass cover adhesion was poor, and the covered cell was weaker than the cell uncovered. Thermal stresses caused some cell delamination from the model solar array substrate.

Josephs, R. H.↗
NASA NTRS1991

Material and tribological considerations for turbopump bearings

The frictional heat generation in the rolling/sliding contact areas of high pressure oxygen turbopump (HPOTP) bearings is a key factor in bearing life. Several bulk materials, surface treatments and coatings are examined for their attributes of rolling contact fatigue life, wear and friction. Emphasis is given to the frictional response of these materials under conditions of rolling with incipient sliding as predicted from HPOTP bearing analysis. Rolling contact fatigue life is shown to be significantly improved with silicon nitride. Fatigue life can also be improved by coating the chromium carbide-laden stainless steels (440C, BG42) with TiN and thin dense chrome. The traction (friction under rolling/sliding) of these materials is discussed in terms of microslip and the presence of interfacial films.

Wedeven, L. D.↗