Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface oxidation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Electrolyte-Induced Restructuring of Acid-Stable Oxygen Evolution Catalysts

Crystalline metal oxide catalysts operating under oxygen evolution reaction (OER) conditions invariably restructure, resulting in active sites with hydroxo/oxo species in an amorphous environment. An increase in the population of terminal hydroxo/oxo species (i.e., edge sites) facilitates proton-coupled electron-transfer (PCET) kinetics for oxygen generation and thus improves catalyst competency. While amorphous films benefit from a greater density of active sites, they suffer from diminished charge transport as compared to that of extended crystalline lattices. Managing this amorphous–crystalline dichotomy is essential when designing OER catalysts, which we highlight with the examination of electrodeposited PbO x materials, which historically are very poor OER catalysts. Along these lines, the presence of phosphate during PbO x electrodeposition truncates the growth of an extended lattice owing to its strong bonding to oxide surfaces to afford an amorphous catalyst film (A-PbO x ) with significant charge-transfer resistance (138 ± 42 Ω) and poor OER kinetics (420 ± 105 mV dec –1 Tafel slope). Conversely, electrodeposition of Pb 2+ in the presence of less coordinating electrolytes such as nitrate affords crystalline β-PbO2 with improved charge-transfer resistance (42.6 ± 1.1 Ω), though still poor OER kinetics (134 ± 36 mV dec –1 Tafel slope). By operating amorphous A-PbOx in less coordinating electrolytes, however, a new partially crystalline material can be generated (μc-PbO x ) with further reduced charge-transfer resistance (33.0 ± 1.4 Ω) and improved OER kinetics (70 ± 15 mV dec –1 Tafel slope). The enhanced OER activity of μc-PbO x is the result of coupling the high edge-site population of an amorphous PbOx phase with crystalline-like charge transport properties. Finally, the ability to use an electrolyte to induce OER activity in an inactive amorphous form of PbO x highlights the benefits of optimizing the amorphous–crystalline phase compositions in the design of active OER catalysts.

catalysts↗
DOE OSTI2024

In-situ hydrogen microstructural characterization of Si heterojunction passivation: Addressing V OC degradation and mitigation pathways

Si heterojunction (SHJ) solar cells have demonstrated record efficiency >27%, approaching the theoretical limit of ≈ 29%, primarily due to best surface/interface defect passivation provided by deposited thin layers of hydrogenated amorphous silicon (a-Si:H). Such excellent surface/interface passivation reduces recombination loss and result in >100 mV improvement of cell open circuit voltage (V OC ) to ≈ 750 mV, thus the cell efficiency. However, fielded SHJ modules exhibit loss of V OC and hence efficiency over time in years, presumably due to degradation related to a-Si:H layers. This adversely affects the technology’s market acceptance, and levelized cost of energy (LCOE). It is hypothesized that the origin of a-Si:H degradation is somehow related to the presence of weak Si–Si bonds and hydrogen in a-Si:H films. The objective of this project is to test this hypothesis by directly measuring chemical and structural changes occurring within SHJ component layers and solar cells. This is achieved by developing an innovative in-situ Fourier transform infrared (FTIR) spectrometry apparatus to monitor hydrogen microstructural changes occurring within amorphous silicon and decipher hydrogen evolution kinetics over time when samples are exposed to heat and/or light stress. These in-situ measured hydrogen microstructural changes are correlated to the changes in effective minority carrier lifetime (τ eff ), implied V OC (iV OC ), surface recombination velocity (S), and cell V OC . These mechanistic understandings will provide critical guidance to mitigate the V OC -driven degradation of SHJ solar cell performance. Passivation optimization and degradation analysis of individual SHJ component structures were achieved through systematic deposition of three symmetric structures and the completed SHJ solar cell structure. The three symmetric structures used were intrinsic a-Si:H [(i)a-Si:H] layers in a bilayer structure, intrinsic and p-type doped stacked layers [(i-p)a-Si:H] representing the front heterojunction in the SHJ cell, and intrinsic and n-typed doped stacked layers [(i-n)a-Si:H] representing the back-side back surface field (BSF) in the SHJ cell. State-of-the-art passivation qualities are demonstrated by a champion iV OC of 740 mV for the (i)a-Si:H layers, and the (i-n)a-Si:H symmetric structure. A 725 mV iV OC is observed for the (i-p)a-Si:H symmetric structure. These symmetric passivated SHJ component structures were subsequently subjected to different accelerated lifetime (ALT) stressors to identify which conditions contribute the most to iV OC degradation. Degradation of the thin (10 nm) (i)a-Si:H passivation layers without any additional overlying layers is minimal; complexity of this study arises due to unavoidable surface oxidation of (i)a-Si:H layer during most of the stress application, which is likely irrelevant for a full SHJ cell configuration with overlying protective layers. The iV OC degradation of symmetric structures is found to occur primarily at the (i-p)a-Si:H passivation stack under dark heat stress with associated hydrogen loss from the (p)a-Si:H layer. An activation energy for increase in S (defect creation) of 0.65 eV can be correlated to the activation energy of ≈ 0.4 eV for hydrogen loss from the (i-p)a-Si:H stack. This also suggests the presence of weakly bonded hydrogen in the (p)a-Si:H films, which effuses out of the film stack at such low activation energy. When light and heat stress are applied together, similar hydrogen loss from (i-p)a-Si:H stack is observed, however, does not appreciably degrade iV OC or increase S. This is an important result and departure from direct correlation between hydrogen loss and defect creation. This perhaps indicates additional defect chemistries or annealing that might be occurring in the presence of light requiring further detailed defect measurements. The full SHJ cell structure used for this project is depicted in Fig.1(d). SHJ cells with an initial V OC ≈ 700 mV were fabricated and subjected to similar ALT stress conditions. Cell V OC is found to degrade the most under dark heat stress and is confirmed by observed hydrogen migration out of the (i-p)a-Si:H stack. However, hydrogen cannot escape from the cell stack, it accumulates near the (p)a-Si:H/ITO contact interface, where ITO acts as a barrier preventing hydrogen loss. Furthermore, light-heat combined stress does not degrade V OC appreciably, confirming the occurrence of a defect annealing process.

14 SOLAR ENERGY↗
DOE OSTI2020

Establishing a Theoretical Landscape for Identifying Basal Plane Active 2D Metal Borides (MBenes) toward Nitrogen Electroreduction

Abstract To achieve efficient ammonia synthesis via electrochemical nitrogen reduction reaction (NRR), a qualified catalyst should have both high specific activity and large active surface area. However, integrating these two merits into one single material remains a big challenge due to the difficulty in balancing multiple reaction intermediates. Here, it is demonstrated that the boron‐analogues of MXenes, namely “MBenes”, could cope with the challenge and achieve the high activity and large reaction region simultaneously toward NRR. Using extensive density functional theory computations and taking 16 MBenes as representatives, it is identified that seven MBenes (CrB, MoB, WB, Mo 2 B, V 3 B 4 , CrMnB 2 , and CrFeB 2 ) not only have intrinsic basal plane activity for NRR with limiting potentials ranging from −0.22 to −0.82 V, but also possess superior capability of suppressing the competitive hydrogen evolution reaction. Particularly, different from the MXenes whose surface oxidation may block the active sites, once oxidized, these MBenes can catalyze NRR via the self‐activating process, reducing O*/OH* into H 2 O* under reaction conditions, and favoring the N 2 electroreduction. As a result, the exceptional activity and selectivity, high active area (≈10 19 m −2 ), and antioxidation nature render these MBenes as pH‐universal catalysts for NH 3 production without introducing any dopants and defects.

Guo, Xiangyu↗
DOE OSTI2024

Formation and Microwave Losses of Hydrides in Superconducting Niobium Thin Films Resulting from Fluoride Chemical Processing

Abstract Superconducting niobium (Nb) thin films have recently attracted significant attention due to their utility for quantum information technologies. In the processing of Nb thin films, fluoride‐based chemical etchants are commonly used to remove surface oxides that are known to affect superconducting quantum devices adversely. However, these same etchants can also introduce hydrogen to form Nb hydrides, potentially negatively impacting microwave loss performance. Here, comprehensive materials characterization of Nb hydrides formed in Nb thin films as a function of fluoride chemical treatments is presented. In particular, secondary‐ion mass spectrometry, X‐ray scattering, and transmission electron microscopy reveal the spatial distribution and phase transformation of Nb hydrides. The rate of hydride formation is determined by the fluoride solution acidity and the etch rate of Nb 2 O 5, which acts as a diffusion barrier for hydrogen into Nb. The resulting Nb hydrides are detrimental to Nb superconducting properties and lead to increased power‐independent microwave loss in coplanar waveguide resonators. However, Nb hydrides do not correlate with two‐level system loss or device aging mechanisms. Overall, this work provides insight into the formation of Nb hydrides and their role in microwave loss, thus guiding ongoing efforts to maximize coherence time in superconducting quantum devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Two-Step Chemical Looping Cycle for Renewable NH 3 Production Based on Non-Catalytic Co 3 Mo 3 N/Co 6 Mo 6 N Reactions

A two-step solar thermochemical looping cycle based on Co 3 Mo 3 N/Co 6 Mo 6 N reduction/nitridation reactions offers a pathway for green NH 3 production that utilizes concentrated solar irradiation, H 2 O, and air as feedstocks. The NH 3 production cycle steps both derive process heat from concentrated solar irradiation and encompass 1) the reduction of Co 3 Mo 3 N in H 2 to Co 6 Mo 6 N and NH 3 ; and 2) nitridation of Co 6 Mo 6 N to Co 3 Mo 3 N with N 2 . Co 3 Mo 3 N reduction/nitridation reactions are examined at different H 2 and/or N 2 partial pressures and temperatures. NH 3 production is quantified in situ using liquid conductivity measurements coupled with mass spectrometry (MS). Solid-state characterization is performed to identify a surface oxygen layer that necessitates the addition of H 2 during cycling to prevent surface oxidation by trace amounts of O 2 . H 2 concentrations of > 5% H 2 /Ar and temperatures >500 °C are required to reduce Co 3 Mo 3 N to Co 6 Mo 6 N and form NH 3 at 1 bar. Complete regeneration of Co 3 Mo 3 N from Co 6 Mo 6 N is achieved at conditions of 700 °C under 25–75% H 2 /N 2 . H 2 pressure-swings are observed to increase NH 3 production during Co 3 Mo 3 N reduction. In conclusion, the results represent the first comprehensive characterization of and definitive non-catalytic production of NH 3 via chemical looping with metal nitrides and provide insights for technology development.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Ending the Chase for a Perfect Binder: Role of Surface Chemistry Variation and its Influence on Silicon Anodes

In this work we examine the influence of the type of silicon source material (two milled and two plasma enhanced chemical vapor deposition) on the electrochemical performance of silicon-based anodes for Li-ion batteries. The four representative Si sources were previously identified in literature but have never been compared side by side, which is critical to understanding the wide variation in performance reported for silicon-based electrodes. These particles display unique surface features associated with surface oxides and residual precursor species (Si-N, Si-C, Si-H) which impact processability by changing interactions within the electrode slurry and the resulting electrochemical performance. These properties should be taken into consideration when utilizing “off-the-shelf” Si powders for investigations and would be good variables to explore to understand why certain chemistries display suitable performance, while others “don't work.”

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Temperature dependence of nickel ion release from nitinol medical devices

Abstract Nitinol exhibits unique (thermo)mechanical properties that make it central to the design of many medical devices. However, nitinol nominally contains 50 atomic percent nickel, which if released in sufficient quantities, can lead to adverse health effects. While nickel release from nitinol devices is typically characterized using in vitro immersion tests, these evaluations require lengthy time periods. We have explored elevated temperature as a potential method to expedite this testing. Nickel release was characterized in nitinol materials with surface oxide thickness ranging from 12 to 1564 nm at four different temperatures from 310 to 360 K. We found that for three of the materials with relatively thin oxide layers, ≤ 87 nm nickel release exhibited Arrhenius behavior over the entire temperature range with activation energies of 80 to 85 kJ/mol. Conversely, the fourth ''black–oxide'' material, with a much thicker, complex oxide layer, was not well characterized by an Arrhenius relationship. Power law release profiles were observed in all four materials; however, the exponent from the thin oxide materials was approximately 1/4 compared with 3/4 for the black–oxide material. To illustrate the potential benefit of using elevated temperature to abbreviate nickel release testing, we demonstrated that a > 50 day 310 K release profile could be accurately recovered by testing for less than 1 week at 340 K. However, because the materials explored in this study were limited, additional testing and mechanistic insight are needed to establish a protective temperature scaling that can be applied to all nitinol medical device components.

Saylor, David M.↗
DOE OSTI2022

UV‐induced degradation of high‐efficiency silicon PV modules with different cell architectures

Abstract Degradation from ultraviolet (UV) radiation has become prevalent in the front of solar cells due to the introduction of UV‐transmitting encapsulants in photovoltaic (PV) module construction. Here, we examine UV‐induced degradation (UVID) in various commercial, unencapsulated crystalline silicon cell technologies, including bifacial silicon heterojunction (HJ), interdigitated back contact (IBC), passivated emitter and rear contact (PERC), and passivated emitter rear totally diffused (PERT) solar cells. We performed UV exposure tests using UVA‐340 fluorescent lamps at 1.24 W·m −2 (at 340 nm) and 45°C through 4.02 MJ·m −2 (2000 h). Our results showed that modern cell architectures are more vulnerable to UVID, leading to a significant power decrease (−3.6% on average; −11.8% maximum) compared with the conventional aluminum back surface field (Al‐BSF) cells (<−1% on average). The power degradation is largely caused by the decrease in short‐circuit current and open‐circuit voltage. A greater power decrease is observed in bifacial cells with rear‐side exposure compared with those with front‐side exposure, indicating that the rear side is more susceptible to UV damage. Secondary ion mass spectroscopy (SIMS) confirmed an increase in hydrogen concentration near the Si/passivation interface in HJ and IBC cells after UV exposure; the excess of hydrogen could result in hydrogen‐induced degradation and subsequently cause higher recombination losses. Additionally, surface oxidation and hot‐carrier damage were identified in PERT cells. Using a spectral‐based analysis, we obtained an acceleration factor of 5× between unpackaged cells (containing a silicon nitride antireflective coating on the front) in the UV test and an encapsulated module (with the front glass and encapsulant blocking 90% of the UV at 294 nm and 353 nm, respectively) in outdoor conditions. From the analytical calculations, we show that a UV‐blocking encapsulant can reduce UV transmission in the module by an additional factor of ~50.

14 SOLAR ENERGY↗
DOE OSTI2021

Influence of Protection Layers on Thermal Stability of Nitride Thin Films

Nitrides are commonly studied for their properties relevant to numerous coating applications, and have been recently used to synthesize newly predicted materials in thin film form. However, thermodynamic stability of such nitride materials is difficult to experimentally evaluate, due to limited thermal budget of thin films. Here we show that thermal stability of nitride films can be extended using protection layers. Specifically, we find that zirconium nitride (ZrN) thin films are stable up to at least 1200°C annealing temperature in N2 atmosphere, if aluminum nitride (AlN) diffusion barriers and capping layers are used. X-ray diffraction (XRD) measurements show the expected thermodynamically stable rocksalt structure of ZrN, and scanning electron microscopy (SEM) confirms compact microstructure of these ZrN films. Without such protection layers, transient bixbyite Zr2ON2 phase and high-temperature ZrSi2 phase are observed after annealing by XRD, SEM, and auger electron spectroscopy (AES), due to side reaction with native surface oxide (ZrOx) and substrate (Si) respectively. These results demonstrate that protection layers are beneficial to increase the thermal budget of nitride thin films, for evaluating thermodynamic stability of new nitride materials, for capturing transient metastable phases during crystallization, and for using functional nitride coatings in extreme environments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Non-Equilibrium Synthesis of Highly Active Nanostructured, Oxygen-Incorporated Amorphous Molybdenum Sulfide HER Electrocatalyst

Molybdenum sulfide emerged as promising hydrogen evolution reaction (HER) electrocatalyst thanks to its high intrinsic activity, however its limited active sites exposure and low conductivity hamper its performance. To address these drawbacks, the non-equilibrium nature of pulsed laser deposition (PLD) is exploited to synthesize self-supported hierarchical nanoarchitectures by gas phase nucleation and sequential attachment of defective molybdenum sulfide clusters. Furthermore, the physics of the process are studied by in situ diagnostics and correlated to the properties of the resulting electrocatalyst. The as-synthesized architectures have a disordered nanocrystalline structure, with nanodomains of bent, defective S-Mo-S layers embedded in an amorphous matrix, with excess sulfur and segregated molybdenum particles. Oxygen incorporation in this structure fosters the creation of amorphous oxide/oxysulfide nanophases with high electrical conductivity, enabling fast electron transfer to the active sites. The combined effect of the nanocrystalline pristine structure and the surface oxidation enhances the performance leading to small overpotentials, very fast kinetics (35.1 mV dec -1 Tafel slope) and remarkable long-term stability for continuous operation up to -1 A cm -2 . This work shows possible new avenues in catalytic design arising from a non-equilibrium technique as PLD and the importance of structural and chemical control to improve the HER performance of MoS-based catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Insights into Acetic Acid Binding and Ketene Formation on Anatase TiO 2 (101)

Understanding the adsorption and reactivity of carboxylic acids on oxide surfaces is of great interest in catalysis for biomass upgrading via ketonization, a carbon–carbon coupling reaction. Herein, we investigate the adsorption and reaction of acetic acid on anatase TiO 2 (101) using scanning tunneling microscopy, infrared spectroscopy, temperature programmed reaction, and density functional theory calculations. We demonstrate the adsorption of acetic acid can form two intermediates: (1) dissociated, bidentate acetate with an associated bridging hydroxyl, and (2) molecular, monodentate acetic acid. The coexistence of ordered phases with increasing monolayer (ML) saturation coverages consisting of (1) pure acetate (0.5 ML), (2) mixed acetate/acetic acid (0.67 ML), (3) mixed acetate/acetic acid (1.0 ML) and (4) pure acetic acid demonstrates similar energetics for both acetate and acetic acid species. Under ultra-high vacuum conditions, the presence of both monodentate acetic acid and bidentate acetate was observed below room temperature, while solely bidentate acetate was observed up to 575 K. The deprotonation of acetic acid produces water at 280 K, while the thermal decomposition of bidentate acetate produces ketene and acetic acid at 645 K. In conclusion, this model study provides detailed insight into the stability and reactivity of carboxylic acid surface-bound intermediates, which could participate during ketonization reactions for biomass upgrading.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Laser Powder Bed Fusion of ODS 14YWT from Gas Atomization Reaction Synthesis Precursor Powders

Abstract Laser powder bed fusion (LPBF) additive manufacturing (AM) is a promising route for the fabrication of oxide dispersion strengthened (ODS) steels. In this study, 14YWT ferritic steel powders were produced by gas atomization reaction synthesis (GARS). The rapid solidification resulted in the formation of stable, Y-containing intermetallic Y 2 Fe 17 on the interior of the powder and a stable Cr-rich oxide surface. The GARS powders were consolidated with LPBF. Process parameter maps identified a stable process window resulting in a relative density of 99.8%. Transmission electron microscopy and high-energy x-ray diffraction demonstrated that during LPBF, the stable phases in the powder dissociated in the liquid melt pool and reacted to form a high density (1.7 × 10 20 /m 3 ) of homogeneously distributed Ti 2 Y 2 O 7 pyrochlore dispersoids ranging from 17 to 57 nm. The use of GARS powder bypasses the mechanical alloying step typically required to produce ODS feedstock. Preliminary mechanical tests demonstrated an ultimate tensile and yield strength of 474 MPa and 312 MPa, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A mini review of cobalt-based nanocatalyst in Fischer-Tropsch synthesis

Fischer-Tropsch (F-T) synthesis, converting syngas to hydrocarbons, provides a green alternative for fuel production. Cobalt is one of the most intensively studied F-T catalysts due to its great activity, high stability, and relatively low cost. Overall, in this mini review, we summarized some recent advancements in the development of cobalt-based F-T catalysts focusing on the effects of particle size, surface oxidation states, crystallography, and bimetallic particles, with emphasis on the research from our group. Furthermore, non-steady state conditions were investigated to access the initial kinetics using chemical transient kinetics (CTK) experiments, which could bring more insights into the reaction mechanism and catalyst design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Helium tribology of Inconel 617 subjected to laser peening for high temperature nuclear reactor applications

Inconel 617 is among the best candidates for utilization in high temperature gas cooled reactor tribo-components. However, the combined effects of sliding contact, along with intermittent idle times and very high temperature material degradation, deteriorates the alloy tribological performance, especially under a helium atmosphere. Laser peening is a surface treatment technique which can enhance the properties at the surface and subsurface by generating deep residual stresses and enhanced microstructure. In this work, we report the tribological behavior of regular laser peened as well as thermally-engineered laser peened Inconel 617 under helium and air atmospheres at 800 °C. In addition to friction and wear studies, the specimens are characterized by different analytical techniques to further understand the mechanisms involved in the peening process and sliding contact. Regardless of the peening process and post-process treatment types, it is observed that laser peening improves the tribological characteristics of Inconel 617. Interestingly, laser peening followed by helium thermal aging shows highly enhanced tribological behavior. This is attributed to the strengthening effect of the laser peening on the surface oxides providing an excellent and lasting protective and lubricating film under helium exposure.

42 ENGINEERING↗
DOE OSTI2022

Origins of wear-induced tungsten corrosion defects in semiconductor manufacturing during tungsten chemical mechanical polishing

During chemical mechanical polishing (CMP) process optimization, a unique corrosion defect was identified in the tungsten (W) contact plugs, which were investigated to develop practical solutions to improve CMP mass productivity. The corrosion defect occurred in the absence of external incident energy and was observed to occur only at the W plugs connected to the P + /n-well close to the wafer edge. To examine the root cause of the corrosion, a series of experiments was carried out at each W CMP step, using in-line defect inspection. Additional experiments were conducted using on-line inductively coupled plasma mass spectrometry (ICP-MS) to understand pH- and potential-dependent electrochemical dissolution behaviors of W. Experimentally, W corrosion was confirmed to be exacerbated if the surface oxide of the W plugs is removed by the deionized water (DIW) rinsing step under wafer pressurization, then exposed to DIW and alkaline cleaning solution. Although the DIW rinsing step is commonly performed to clean polishing pads right after the main polishing, a small amount of applied pressure (0.5 psi) without slurry supply can lead to corrosion defects. Finally, this wear-induced corrosion of the W plugs can be prevented by removing the applied pressure during the post DIW rinsing step of W CMP.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

The origin of passivity in aluminum-manganese solid solutions

In this work, the effects of manganese on the aqueous corrosion of aluminum-manganese alloys were investigated by experiments and atomistic simulations. Electrochemical measurements, x-ray photoelectron spectroscopy, and atom probe tomography analysis indicate that manganese addition enhanced the corrosion resistance of aluminum without participating in the surface oxidation. Furthermore, the selective dissolution of manganese was believed to increase the free volume at the metal/oxide interface to facilitate the formation of a denser, thinner oxide layer with closer to stoichiometry composition. Atomistic simulations showed that the oxide layer compactness increased, and defect density decreased with increasing free volume content in Al, resulting in enhanced barrier characteristics.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Scaling dynamics in low-salt-rejection reverse osmosis for high-salinity produced water desalination: Mechanistic modeling and membrane autopsy

Membrane scaling remains a critical barrier to the reliable operation of desalination systems, particularly for hypersaline produced water (PW) treatment. This study fills the knowledge gap of autopsy-based model validation for PW desalination by elucidating scaling mechanisms in a Low-Salt-Rejection Reverse Osmosis (LSRRO) system through the integration of pilot-scale experimentation and complementary modeling approaches. A semi-empirical modeling framework was developed and applied to a multistage pilot LSRRO system equipped with nanofiltration and RO membranes treating high-salinity PW from the Permian Basin. Water quality analysis showed that total dissolved solids decreased from ~130,000 mg/L to ~1900 mg/L in the permeate, then further reduced to ~300 mg/L by a second-pass RO. Two different thermodynamic modeling approaches were evaluated: the first extends the LSRRO framework by incorporating system complexity and scaling phenomena, whereas the second method explicitly captures concentration polarization in localized supersaturation. Both methods illustrate the tendency for carbonate and sulfate scaling throughout the stages. Membrane autopsies revealed a silica-dominated deposit matrix, localized CaSO 4 at Stage 2, and minor barite/celestite despite their prominence in model predictions. Quantum-chemical calculations indicated silica scaling can be rationalized by favorable adsorption of H 4 SiO 4 on Fe-oxide surfaces (ΔG ≈ −44 kJ/mol), providing a kinetic pathway for interfacial inorganic polymerization even when bulk equilibrium predictions are conservative. Overall, the thermodynamic scaling modeling and membrane autopsy revealed heterogeneous, localized deposits with limited impact on LSRRO performance, while quantum analysis rationalized the thermodynamically unfavorable precipitation formation under bulk equilibrium, reconciling model–autopsy discrepancies. These insights support targeted pretreatment and silica-specific antiscalants to extend membrane lifetime and increase recovery, providing a transferable framework for hypersaline water desalination systems. The combined experimental–computational approach provides new mechanistic insight into scaling in hypersaline membrane systems and establishes a transferable framework for predicting and mitigating scaling in next-generation desalination technologies.

Low-salt-rejection reverse osmosis↗
DOE OSTI2020

Selective activation of methane C–H bond in the presence of methanol

Direct methane to methanol (MTM) conversion over heterogeneous catalysts is a promising route for valorization of methane. The methane C-H bond activation is considered as the key step of the MTM and is the focus of considerable research activity. However, the formed methanol typically suffers from overoxidation largely due to the cleavage of a methanol C-H bond, whose bond dissociation energy is ca. 0.5 eV lower than that of the methane C-H bond, which usually translates to a transition state energy of the methanol C-H bond cleavage that is ca. 0.55 eV lower than that of methane whenever the reactions proceed through a radical mechanism. Furthermore, we propose a general approach for decreasing the transition state energy difference between the CH 4 and CH 3 OH C-H bond dissociation. When a metal-oxide supported cationic transition metal atom and a neighboring oxygen on the oxide surface serve as the active site, the transition state energy difference through a surface-stabilized pathway can be noticeably narrowed as compared with that of a radical pathway. For Ir, Pt and Rh-doped anatase TiO 2 (101), the CH 4 C-H bond activation can be preferred over that of CH 3 OH at significant methanol mole fraction. Also, for PdAu alloys containing adsorbed oxygen and positively charged Pd, calculations suggest in agreement with recent experiments (Science 367 (6474), 193-197) that the CH 4 C-H bond can be selectively activated in the presence of CH 3 OH.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗