Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Performance of biochar assisted catalysts during hydroprocessing of non-edible vegetable oil: Effect of transition metal source on catalytic activity

Biochar-supported catalysts were developed from nickel (Ni) - and cobalt (Co)- nitrates and hydroxides and tested for the hydrotreatment of carinata oil. Nitrate-based (from water-soluble salts) and hydroxide-based (from water-insoluble salts) catalysts of Ni and Co were prepared via wetness impregnation and aqueous dispersion methods, respectively. The catalysts were characterized using various tools such as, confocal XRF, BET specific surface area analyzer, NH3-TPD, and SEM-EDS. Synchroton method showed nitrate-sourced metals were dispersed mostly in the pores while, the hydroxide-sourced metals were distributed mainly on the catalyst surface. C = C saturation and cracking of triglycerides, decarboxylation, and hydrogenation of aromatic structures appeared to be dominant on the hydroxides of transition metals, hence took place on catalyst surface. Methanation and dehydrogenation (thus aromatization), however, seemed to be a pore phenomenon, catalyzed more over nitrate-based catalysts. A reaction network was proposed based on chemical analysis of upgraded carinata oil and erucic acid model compound. Catalytic cracking followed by hydrotreatment performed better in terms of fuel properties than other approaches in this study.

Biochar catalysts↗
DOE OSTI2026

Probing Terra Incognita of Ni–P Catalysts: Operando Explorations during Hydrogen Evolution Reaction

We have developed two Ni phosphide preparation methods allowing operando XAS surface-sensitive studies of well-defined bulk systems. For Ni K-edge XAS, a Ni 2 P phase-pure powder was sintered into a high-density pellet and polished for grazing incidence XAS. Ni sites were mildly affected by the acidic electrolyte prior to the HER, while the applied cathodic potential caused the reduction of Ni surface states beyond the states of as-prepared Ni 2 P. The computed fully H-covered Ni 2 P [0001] model describes the difference in the operando Ni K-edge GIXAS spectrum well. Upon turning the applied bias off, the Ni sites became immediately oxidized, forming NiO on the surface. Thus, the active phase during the HER is covalent Ni 0 close to that in the intermetallic phosphides, and Ni 2+ oxides formed after, and not during, the HER. For P K-edge XAS, Ni foam was phosphorized to form a thin Ni 3 P layer while preserving its high surface area. Upon immersion in the acidic electrolyte, the P sites underwent removal of P 5+ phosphates and formed new P coordination, possibly due to the adsorption of protons from the electrolyte. These new P surface states were not affected by turning the cathodic current on and off as soon as the sample was immersed in the acidic electrolyte. However, the removal of the sample from the electrochemical cell and drying in air resulted in substantial depletion and oxidation of surface P. Echoing the observed Ni site chemistry during HER, XAS and XPS suggest that the in situ active P sites are different from the oxidized P states observed under ex situ conditions.

Kong, Seongyoung [Iowa State Univ., Ames, IA (Unit↗
DOE OSTI2021

Atmospheric Transport of North African Dust-Bearing Supermicron Freshwater Diatoms to South America: Implications for Iron Transport to the Equatorial North Atlantic Ocean

The equatorial North Atlantic Ocean (NAO) is a nutrient-limited ecosystem that relies on the deposition of long-range transported iron (Fe)-containing aerosols to stimulate primary productivity. Using microscopy, we characterized supermicron and supercoarse mode African aerosols transported to the western NAO in boreal winter/spring. In this work, we detected three particle types including African dust, primary biological aerosol particles, and freshwater diatoms (FDs). FDs contained 4% Fe by weight due to surficial dust inclusions that may be susceptible to chemical processing and dissolution. FDs were typically larger than dust particles and comprised 38% of particles between 10 and 18 μm in diameter. The low density, high surface-area-to-volume ratio, and large aspect ratios of FD particles suggest a mechanism by which they can be carried great distances aloft. These same properties likely increase the residence time of FDs in surface waters thereby increasing the time for Fe dissolution and their potential impact on marine biogeochemical cycles.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Effect of Particle Size on the Dissolution of Pt 3 Co/C and Pt/C PEMFC Electrocatalysts

Potentiostatic and potentiodynamic Pt and Co dissolution were investigated for three Pt 3 Co/C catalysts with particle sizes of 4.9, 8.1, and 14.8 nm in aqueous electrolyte at potentials encountered by the PEMFC cathode. For all three Pt 3 Co/C catalysts under prolonged potentiostatic dissolution, the dissolved Pt steady state concentration increases from 0.85 V to reach a maximum at 1.1−1.15 V and decreases at higher potentials. The dependence of the dissolved Pt steady state concentration on particle size reveals that catalyst stability decreases with decreasing mean particle size, whereas the stability under potential cycling conditions is non-monotonic with particle size. Preferential dissolution of Co from all three Pt 3 Co catalysts was observed at all potentials, which increases at >1.1 V, the region over which Pt dissolution decreases, reflecting the opposing effects of Pt oxide formation on Pt and Co dissolution. Comparison of Pt 3 Co/C and Pt/C with similar mean particle sizes (4.9 vs 5.0 nm) and particle size distributions reveals that the Pt 3 Co/C has a higher potentiostatic dissolution rate (4–5 times), a higher steady state concentration of dissolved Pt (∼2 times), and a larger change in electrochemically-active surface area (ECA) (18 times) after prolonged cycling, indicating that Pt 3 Co has inferior stability. The higher rates of Pt dissolution for Pt 3 Co vs Pt have been attributed to higher extents of surface Pt oxidation, as determined using voltammetric oxide reduction charges and the white line intensities in Pt L 3 X-ray absorption spectra.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Design and synthesis of biobased superhydrophobic biochar catalyst derived from Citrus sinensis for biodiesel production using inedible oil feedstocks

In an one-pot in situ trans/esterification of low-grade feedstocks, the simultaneous presence of triglycerides (TAGs) and free fatty acids (FFAs) presents a dual catalytic challenge. While TAGs undergo transesterification to form biodiesel and glycerol, FFAs present in the feedstocks are esterified simultaneously, producing water as a by-product. This water can deactivate acid catalysts by interacting with their active sites, reducing catalytic efficiency and reusability. To overcome this, we developed a hydrophobic sulfonic acid-functionalized biochar catalyst derived from Citrus sinensis (orange peel) via sulfonation with H 2 SO 4 and subsequent silylation using hexamethyldisilazane (HMDS). The optimized catalyst exhibited a high surface area (355.09 m 2 g −1 ), sulfur content (5.33 wt%), and strong hydrophobicity (water contact angle: 154°). Compared to non-hydrophobic analogs, it showed enhanced activity and reusability (up to 10 cycles). Using response surface methodology with central composite design, a biodiesel yield of 99.1 ± 0.4% was achieved under optimal conditions. Life cycle assessment was performed to evaluate the environmental impacts of biodiesel production utilising the synthesized catalyst, considering 1000 kg of biodiesel produced as 1 functional unit. In conclusion, the recorded results showed the cumulative abiotic depletion of fossil resources over the entire biodiesel production process as 87 243.423 MJ and global warming potential as 4103.494 kg CO 2 equivalent.

Biochar↗
DOE OSTI2021

Lattice site–dependent metal leaching in perovskites toward a honeycomb-like water oxidation catalyst

Metal leaching during water oxidation has been typically observed in conjunction with surface reconstruction on perovskite oxide catalysts, but the role of metal leaching at each geometric site has not been distinguished. Here, we manipulate the occurrence and process of surface reconstruction in two model ABO 3 perovskites, i.e., SrSc 0.5 Ir 0.5 O 3 and SrCo 0.5 Ir 0.5 O 3 , which allow us to evaluate the structure and activity evolution step by step. The occurrence and order of leaching of Sr (A-site) and Sc/Co (B-site) were controlled by tailoring the thermodynamic stability of B-site. Sr leaching from A-site mainly generates more electrochemical surface area for the reaction, and additional leaching of Sc/Co from B-site triggers the formation of a honeycomb-like IrO x H y phase with a notable increase in intrinsic activity. A thorough surface reconstruction with dual-site metal leaching induces an activity improvement by approximately two orders of magnitude, which makes the reconstructed SrCo 0.5 Ir 0.5 O 3 among the best for water oxidation in acid.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Segregation induced core-shell structure

A process for synthesis of PtNi high surface area core/shell particles. The processing including formation of PtNi nanoparticles, exposure of the PtNi nanoparticles to oxygen to form a nickel oxide coating on the nanoparticles at the same time the segregation of Ni to surface induces a Pt-skin with PtNi core structure, removal of the nickel oxide coating to form PtNi core/Pt shell (or Pt-skin) structure.

Wang, Rongyue↗
DOE OSTI2021

AI-Improved Resolution Projections of Population Characteristics and Imperviousness Can Improve Resolution and Accuracy of Urban Flood Predictions

Focal Area: (2) Predictive modeling through the use of AI techniques and AI-derived model components. Specifically, we call for the use of deep generative models from ML for providing high-resolution projections of impervious surface area, as well as neural network solvers for fast approximation of urban hydrodynamics to provide greatly enhanced forecasts of future urban flood dynamics.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Distributed Magnetic Field and Temperature Monitoring for Superconducting Radio Frequency Cavities

The overall objective of the proposed Phase I program was to design, construct and demonstrate a fiber optic sensing system capable of providing temperature and magnetic field measurements with an enhanced spatial resolution that can be implemented over a large surface area (cryomodules) to survey superconducting radio frequency cavities and magnets. A magnetic field sensor capable of detecting fluxes on the order of 1 μT is required to detect the distribution of trapped flux on the cavity surface. A unique distributed magnetic field sensor was successfully designed and constructed to demonstrate the detection of magnetic fluxes less than 500 nT. The sensor leveraged the ultra-high sensitivity of Sentek’s picoDAS to measure the magnetostriction induced vibrations in a commercially available Metglas 2605 SC ribbon that was in physical contact with sensing fiber. Static magnetic fields were detected by applying an alternating current a copper wire proximate to the Metglas 2605SC ribbon to create an AC bias magnetic field. In an alternative approach, an AC bias magnetic field was applied to a special magnetic field sensing fiber with Metglas 2605SC cladding successfully detect a magnetic field flux of a 3 μT. Exhaustive testing was performed to characterize the dependency of sensor response on the direction of the applied magnetic field. Although the special sensing fiber based magnetic field sensor did not exhibit an observable dependence on the direction of the magnetic field, the Metglas 2605SC ribbon sensor exhibited a clear directional dependence. A wide variety of polymer materials were evaluated to enhance the temperature response of an FBG based sensor at cryogenic temperatures. The processing and performance challenges provided the motivation to develop a new simple cryogenic temperature sensor that uses a commercially available fiber optic splice protector. The EVA hot melt tube that becomes adhered to the optical fiber and the polyolefin outer tube that shrinks upon heating in the fusion splicer heater provide the high thermal expansion coefficient necessary to impart a significant strain on the FBG when exposed to cryogenic temperatures. The temperature sensitivity (Δ𝜆𝐵𝑟𝑎𝑔𝑔~ 62 𝑝𝑝𝑚/℃) of the FBG-based sensor was on par with the best reported to date. The simple design, use of readily available cost-effective materials, and well-established processing techniques lends this approach to the creation of hundreds to thousands of temperature sensors on one single optical fiber length. The inherently small form factor also allows for co-location with the distributed magnetic field sensor. In preparation for field testing of the prototype sensing system at the Jefferson Labs in potential Phase II program, several different cable designs were evaluated to package the sensors. The preliminary successful demonstration of fully functional sensing cables provides the foundation for subsequent development efforts to advance the Technology Readiness Level of the technology. The technical feasibility of the proposed approach was successfully demonstrated in this Phase I effort.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Superionic Surface Li-Ion Transport in Carbonaceous Materials

Unlike Li-ion transport in the bulk of carbonaceous materials, little is known about Li-ion diffusion on their surface. Here, in this study, we have discovered an ultrafast Li-ion transport phenomenon on the surface of carbonaceous materials with limited reversible Li insertion capacity and high surface area. An ionic conductivity of 18.1 mS cm –1 at room temperature is observed in lithiated Ketjen black (KB), far exceeding those of most solid-state ion conductors. Theoretical calculations reveal low diffusion barriers for the surface Li species. As a result, lithiated KB functions effectively as an interlayer between Li and solid-state electrolytes (SSEs) to mitigate dendrite growth. Further, lithiated KB acts as a high-performance mixed ionic–electronic conductor and replaces solid electrolytes to enhance graphite anode performance, demonstrating full utilization with ∼85% capacity retention over 300 cycles. The discovery of this surface-mediated ultrafast Li-ion transport mechanism provides new directions for the design of solid-state ion conductors and solid-state batteries.

Li metal batteries↗
DOE OSTI2020

Experimental and Computational Studies of Carbon–Carbon Bond Formation via Ketonization and Aldol Condensation over Site-Isolated Zirconium Catalysts

We report here the preparation and investigation of isolated Zr centers supported on a high surface area silica for the conversion of carboxylic acids to internal ketones by ketonic decarboxylation (ketonization) and the aldol condensation of ketones to dimeric enones. Catalysts were synthesized by the grafting of Cp 2 ZrCl 2 on the surface of amorphous silica. The connectivity of Zr was characterized by XRD, UV-vis, and Raman spectroscopy. For the lowest Zr loading, Zr is present predominantly as isolated monomeric species. As the Zr loading is increased, a progressively larger fraction of Zr forms oligomeric species and ZrO nanoparticles. Measurements of catalytic activity show that the turnover frequency for carboxylic acid ketonic decarboxylation reaction and aldol condensation of ketones decreases monotonically with increasing Zr loading. An H/D kinetic isotope effect was not observed over isolated Zr catalysts, suggesting that α-H abstraction is not the rate-determining step, rather C-C bond forming may be rate limiting for both reactions. This conclusion is supported by computational modeling of the reaction mechanism. The proposed catalytic cycle for ketonization proceeds via a β-keto acid intermediate on isolated Zr sites that are always coordinatively saturated with C-C bond formation as the rate-limiting step. C-C bond formation is also rate-determining for aldol condensation, with an apparent activation energy that is in good agreement with the experiment if the resting state is a saturated ≡ZrOH site with two adsorbed ketone molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Additively Manufacturing Nitinol Shape Memory Alloys for Advanced Actuator Designs

The objective of this research was to understand the role of feedstock production in the phase transformation behavior of additively manufactured Ni-Ti alloys for advanced actuator design. Industrial adoption of additively manufactured Ni-Ti alloys depends on the ability to produce repeatable phase transformation behavior, quantified here by the austenite to martensite transformation on heating. Small variations in the alloy composition may have a significant effect on the temperature at which this transformation occurs. This project showed that the powder characteristics play an important role in determining this behavior. Increases in the surface area per unit volume of the powder, either as a function of size distribution or morphology, have the effect of reducing the Ti content in the alloy through the formation of Ti-rich oxides on the powder surface, which has the effect of depressing the transformation temperature. Preferential Ni vaporization during additive manufacturing can partially offset this effect. To achieve repeatable results, it is important to understand the effect of powder oxidation, and to control the powder characteristics.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Macroscale properties and atomic-scale mechanisms of ash removal in low-temperature hydrothermal carbonization

Biogenic ash is a significant impediment to the utilization of agricultural residues in biofuel production. Such challenge can be addressed by various treatments, as demonstrated in this study on the experimental and computational mechanisms involved in the hydrothermal treatment (HT) of wheat straw. A combination of classical (all-atom) molecular dynamics simulations of cellulose carrying silica and calcium species, along with first principles quantum chemical calculations, indicates the dissociation of inorganics from the cellulose with increased HT temperature. Here, this observation is confirmed by experimental evidence of effective ash removal by HT, showing at least 50% removal of sulfur, chlorine, potassium, and calcium, and 12.5% of silica, leading to a reduced total ash content (from 6.7% to 4.2%).Changes in structural features upon HT, such as surface cellular structure and porosity, were revealed, accompanied by an increased specific surface area (from 1.17 to 6.34 m 2 /g). Our simulations suggest that silica binds tightly to the hydrophobic face of cellulose at room temperature, but HT significantly reduces the binding free energy of association with both hydrophobic and hydrophilic surfaces. Most significantly, ash removal leads to an increased calorific value, rising from approximately 16 MJ/kg to about 19 MJ/kg, along with improved thermal behavior. The improved integration combustion index parameter S indicates that the combustion properties improve with ash removal efficiency. The proposed atomic-level mechanism for the observed removal of inorganics during mild HT underscores the potential of such treatment in producing energy-dense wheat straw, a widely available agricultural residue.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Trace Fe activates perovskite nickelate OER catalysts in alkaline media via redox-active surface Ni species formed during electrocatalysis

The accurate description of activity trends among perovskite-oxide oxygen-evolution-reaction (OER) catalysts using electronic-structure descriptors requires that the bulk structure of the catalyst is comparable to that of the surface. Few studies have addressed the dynamic nature of the catalyst's structure during the OER and the consequential implications for understanding activity. Here, we use a combination of electrochemical and materials-characterization techniques to study the surface reconstruction and the associated formation of a new redox-active phase on LaNiO 3 particles, LaNiO 3 epitaxial films, and an analogous Ruddlesden-Popper phase, La 2 NiO 4 . Small, but characteristic, redox features corresponding to Ni redox in nominally amorphous NiO x H y are observed during cyclic voltammetry of these initially fully crystalline materials. The size of these redox features grows with prolonged cycling and contributes to an increased surface area as determined from electrochemical impedance spectroscopy (EIS). Here we find the OER activity is strongly dependent on soluble Fe species in the electrolyte, common impurities in alkaline media. These observations are consistent with the reconstruction of the crystalline surface to form NiO x H y species and subsequent activation by adsorption of Fe forming the well-known and extremely active NiFeO x H y OER catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Elucidation of Active Sites in Aldol Condensation of Acetone over Single-Facet Dominant Anatase TiO 2 (101) and (001) Catalysts

Aldol condensations of carbonyl compounds for C–C bond formation are a very important class of reactions in organic synthesis and upgrading of biomass-derived feedstocks. However, the atomic level understanding of reaction mechanisms and structure-activity correlation on widely used transition metal oxide catalysts are limited due to the high degree of struc-tural heterogeneity of catalysts such as commercial TiO 2 powders. Here, we provide a deep understanding of the reaction mechanisms, kinetics, and structure–function relationships for vapor phase acetone aldol condensation through the con-trolled synthesis of two catalysts with high surface areas and clean, dominant facets, coupled with detailed characterization and kinetic studies that are further assisted by density functional theory (DFT) calculations. Temperature-dependent diffuse reflectance infrared Fourier transform spectroscopy showed the existence of abundant acetone bonded to surface hydroxyl groups (acetone-O s H) and acetone bonded to Lewis acid sites (acetone-Ti 5c ) on surface of both {101} and {001} facet dom-inant TiO 2 . Intermolecular C–C coupling of enolate intermediate from acetone-Ti 5c and a vicinal acetone-O s H is a kinetically relevant step, which is consistent with kinetic and isotopic studies and DFT calculations. The {001} facet showed a lower apparent activation energy (or higher reactivity) than the {101} facet. This is likely caused by the weaker Lewis acid and Brønsted base strengths of the {001} facet which favors the reprotonation–desorption of the coupled intermediate, making the C–C coupling step more exothermic on the {001} facet and resulting in an earlier transition state with a lower activation barrier. It is also possible that the {001} facet has a smoother surface configuration and less steric hindrance during intermo-lecular C–C bond formation than the {101} facet.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Bridging knowledge gaps in liquid- and vapor-fed CO 2 electrolysis through active electrode area

Increased use of gas diffusion electrodes for CO 2 electroreduction widens the experimental phase space that was previously inaccessible using foil electrodes, raising fundamental questions over the impacts of key variables that translate between liquid- and vapor-fed CO 2 electrolysis systems. This work focuses on studying the interplay of current-potential profiles and electrochemically active surface area (ECSA) by implementing a Cu nanoflower catalyst morphology. The results show decreased overpotentials as much as 460 and 174 mV for foil and gas diffusion electrodes, respectively, while maintaining or improving multi-carbon product current density. Furthermore, these overpotential shifts and product activities normalized by ECSA lead to current-potential relationships akin to those of the Tafel description, which are found through a continuum model to be useful for describing the roughness dependence for both liquid- and vapor-fed systems. This analysis establishes a holistic approach for establishing catalyst design criteria to improve materials development for CO 2 .

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Potential–Dependent BDAC Adsorption on Zinc Enabling Selective Suppression of Zinc Corrosion for Energy Storage Applications

Utility-scale zinc (Zn) batteries are a promising solution to address the problem of intermittency of renewable energy sources; however, Zn-metal anodes in these batteries suffer from capacity loss due to spontaneous corrosion of the Zn especially when high-surface area anode configurations are employed. Additionally, Zn dendrites are known to form during battery charging limiting the cycle-life of these batteries. Electrolyte additives have been explored that prevent aforementioned issues, but these too come at a cost, i.e., surface-blocking additives polarize the electrode surface leading to loss in the voltaic and energy efficiencies of the battery. In this contribution, a novel electrolyte additive, benzyldimethylhexadecylammonium chloride (BDAC), is investigated for its ability to suppresses corrosion of Zn in an acidic (pH = 3) electrolyte. An attribute of BDAC distinct from previously studied additives is that it selectively suppresses electrochemical activity when the Zn electrode is at its corrosion potential; however, during high-rate Zn deposition (charging) or stripping (discharging), BDAC is essentially deactivated and thus it does not appreciably polarize the electrode surface, thus minimizing voltaic efficiency losses. This selective corrosion suppression behavior is explored using slow-scan voltammetry, which reveals hysteresis implying a potential- or current-dependent BDAC adsorption mechanism in which BDAC reaches higher surface coverages when the partial currents at the Zn surface are low (e.g., at or near the corrosion potential), but BDAC coverage is reduced considerably when the Zn deposition or stripping rates are increased. Numerical simulations of the BDAC diffusion-adsorption process corroborate this mechanism. Ramifications of our approach to the selective suppression of Zn dendrites are discussed.

25 ENERGY STORAGE↗