SEARCH · Engineering Papers

Results for “simulated emission”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

All sources NASA NTRS DOE OSTI

NASA NTRS2007

An Analysis of the Effects of RFID Tags on Narrowband Navigation and Communication Receivers

The simulated effects of the Radio Frequency Identification (RFID) tag emissions on ILS Localizer and ILS Glide Slope functions match the analytical models developed in support of DO-294B provided that the measured peak power levels are adjusted for 1) peak-to-average power ratio, 2) effective duty cycle, and 3) spectrum analyzer measurement bandwidth. When these adjustments are made, simulated and theoretical results are in extraordinarily good agreement. The relationships hold over a large range of potential interference-to-desired signal power ratios, provided that the adjusted interference power is significantly higher than the sum of the receiver noise floor and the noise-like contributions of all other interference sources. When the duty-factor adjusted power spectral densities are applied in the evaluation process described in Section 6 of DO-294B, most narrowband guidance and communications radios performance parameters are unaffected by moderate levels of RFID interference. Specific conclusions and recommendations are provided.

LaBerge, E. F. Charles↗

NASA NTRS1993

Extended hot-gas halos around starburst galaxies

A reanalysis of Einstein Imaging Proportional Counter (IPC) data and new observations from the Ginga Large Area (Proportional) counters (LAC) indicate the presence of extended X-ray emission (10-50 kpc) around the starburst galaxy M82. Here, we discuss our model of this emission, which was obtained by performing numerical hydrodynamic simulations of the starburst event to much later times and larger scales than were previously considered. For our models, we adopted a supernova rate of 0.1/yr, and an extended low-density static halo that is bound to the galaxy. There are three stages to the evolution of the wind-blown bubble and the propagation of the shock front: the bubble expands in an almost uniform density disk gas, with a deceleration of the shock front (t is less than or approximately 3.6 Myr); breakout from the disk and the upward acceleration of the shock front (3.6 Myr is less than or approximately t is less than or approximately 18 Myr); propagation into the halo, leading to a more spherical system and shock deceleration (18 Myr is less than or approximately t). For a halo density of 10(exp -3)/cu cm, the outflow reaches a distance of 40-50 kpc from the center of the starburst galaxy in 50 Myr. We calculated the time evolution of the X-ray luminosity and found that the extended starburst emits 3 x 10(exp 39) erg/s to 10(exp 40) in the Ginga LAC band and approximately 10(exp 41) erg/s in the Einstein band. The degree of the ionization equilibrium in the outflow and its effect on the iron K alpha line emission are discussed.

Tomisaka, Kohji↗

NASA NTRS1984

Emission FTIR analyses of thin microscopic patches of jet fuel residue deposited on heated metal surface

Deposits laid down in patches on metal strips in a high pressure/high temperature fuel system simulator operated with aerated fuel at varying flow rates were analyzed by emission FTIR in terms of functional groups. Significant differences were found in the spectra and amounts of deposits derived from fuels to which small concentrations of oxygen-, nitrogen-, or sulfur-containing heterocyclics or metal naphthenates were added. The spectra of deposits generated on strips by heating fuels and air in a closed container were very different from those of the flowing fluid deposits. One such closed-container dodecane deposit on silver gave a strong surface-enhanced Raman spectrum.

Lauer, J. L.↗

NASA NTRS2019

Uncertainty Quantification of a Rotorcraft Conceptual Sizing Toolsuite

A computational framework to support the quantification of system uncertainties and sensitivities for rotorcraft applications is presented using the NASA Design and Analysis of Rotorcraft (NDARC) conceptual sizing tool. A 90 passenger conceptual tiltrotor configuration was used for case demonstration in the modeling of uncertainties in NDARCs emission module. A non-intrusive forward propagation uncertainty quantification approach was applied to ensemble simulations using a Monte Carlo methodology with stratified Latin hypercube sampling. An off-the-shelf software, DAKOTA, which supports trade studies and design space exploration, including optimization, surrogate modeling and uncertainty analysis was used to address the research goals. A toolsuite was further developed incorporating DAKOTA with automated design processes and methods using function wrappers to execute program routines including support for data post-processing. Uncertainties in rotorcraft emissions modeling using the Average Temperature Response metric for a set mission profile were studied. It was shown that for the current study, using the base-line best estimate modeling parameters for the Average Temperature Response metric, NDARC under-estimates the effects of emissions when compared with results from Monte Carlo simulations. A global sensitivity analysis was further undertaken to quantify the contribution of the various emission species on output sensitivity, hence uncertainty. The work demonstrates that the developed toolsuite is robust and will support the quantification of system uncertainties and sensitivities in future rotorcraft design efforts.

Rotorcraft↗

NASA NTRS1987

Secondary electron generation, emission and transport: Effects on spacecraft charging and NASCAP models

Secondary electrons control a spacecraft's response to a plasma environment. To accurately simulate spacecraft charging, the NASA Charging Analyzer Program (NASCAP) has mathematical models of the generation, emission and transport of secondary electrons. The importance of each of the processes and the physical basis for each of the NASCAP models are discussed. Calculations are presented which show that the NASCAP formulations are in good agreement with both laboratory and space experiments.

Katz, Ira↗

NASA NTRS1984

Wave emissions from dc and modulated electron beams on STS 3

During the third Space Shuttle Columbia flight (STS 3) in March 1982, investigations were conducted to assess the electrical, electromagnetic, and plasma environment of the orbiter and to diagnose wave emissions and related plasma effects due to the injection of an electron beam into the surrounding ionosphere. Attention is given to wave emissions and related plasma processes which were stimulated by the first electron beam emissions from the Space Shuttle. The on-orbit measurements are compared to measurements made in a space simulation chamber. Instrumentation and operations are considered along with the plasma effects of beam emissions, wave emissions from dc beams, wave emissions from VLF-modulated beams, and wave emissions from ELF-modulated beams.

Shawhan, S. D.↗

NASA NTRS2011

Simulation of Relativistic Shocks and Associated Radiation from Turbulent Magnetic Fields

Using our new 3-D relativistic particle-in-cell (PIC) code, we investigated long-term particle acceleration associated with a relativistic electron-positron jet propagating in an unmagnetized ambient electron-positron plasma. The simulations were performed using a much longer simulation system than our previous simulations in order to investigate the full nonlinear stage of the Weibel instability and its particle acceleration mechanism. Cold jet electrons are thermalized and ambient electrons are accelerated in the resulting shocks. Acceleration of ambient electrons leads to a maximum ambient electron density three times larger than the original value as predicted by hydrodynamic compression. Behind the bow shock, in the jet shock, strong electromagnetic fields are generated. These fields may lead to time dependent afterglow emission. In order to go beyond the standard synchrotron model used in astrophysical objects we have used PIC simulations and calculated radiation based on first principles. We calculated radiation from electrons propagating in a uniform parallel magnetic field to verify the technique. We also used the technique to calculate emission from electrons based on simulations with a small system. We obtain spectra which are consistent with those generated from electrons propagating in turbulent magnetic fields. This turbulent magnetic field is similar to the magnetic field generated at an early nonlinear stage of the Weibel instability. A fully developed shock within a larger system may generate a jitter/synchrotron spectrum.

Nishikawa, K.-I.↗

NASA NTRS2006

Impact of Three-Dimensional Radiative Effects on Satellite Retrievals of Cloud Droplet Sizes

There are several dozen papers that study the effects of cloud horizontal inhomogeneity on the retrievals of cloud optical thickness, but only a few of them deal with cloud droplet sizes. This paper is one of the first comprehensive attempts to fill this gap: It takes a close theoretical look at the radiative effects of cloud 3-D structure in retrievals of droplet effective radii. Under some general assumptions, it was found that ignoring subpixel (unresolved) variability produces a negative bias in the retrieved effective radius, while ignoring cloud inhomogeneity at scales larger than a pixel scale (resolved variability), on the contrary, leads to overestimation of the domain average droplet size. The theoretical results are illustrated with examples from Large Eddy Simulations (LES) of cumulus (Cu) and stratocumulus (Sc) cloud fields. The analysis of cloud drop size distributions retrieved from both LES fields confirms that ignoring shadowing in 1-D retrievals results in substantial overestimation of effective radii which is more pronounced for broken Cu than for Sc clouds. Collocated measurements of broken Cu clouds by Moderate Resolution Imaging Spectrometer (MODIS) and Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) are used to check simulations and theory with observations. The analysis of ASTER and MODIS data and associated derived products recommends against blindly using retrieved effective radii for broken cloud fields, especially if one wants to relate aerosol amounts to cloud droplet sizes.

Marshak, Alexander↗

NASA NTRS2005

Nighttime Cirrus Detection using Atmospheric Infrared Sounder Window Channels and Total Column Water Vapor

A method of cirrus detection at nighttime is presented that utilizes 3.8 and 10.4 (micro)m infrared (IR) window brightness temperature differences (dBT) and total column precipitable water (PW) measurements. This technique is applied to the Atmospheric Infrared Sounder (AIRS) and Advanced Microwave Sounding Unit A (AMSU-A) instrument suite on board EOS-Aqua, where dBT is determined from sets of carefully selected AIRS window channels, while PW is derived from the synergistic AIRS and AMSU-A water vapor retrievals. Simulated and observed dBT for a particular value of PW are not constant; several physical factors impact dBT, including the variability in temperature and relative humidity profiles, surface emissivity, instrument noise, and skin/ near-surface air temperature differences. We simulate clear-sky dBT over a realistic range of PWs using 8350 radiosondes that have varying temperature and relative humidity profiles. Thresholds between cloudy and uncertain sky conditions are derived once the scatter in the clear-sky dBT is determined. Simulations of optically thin cirrus indicate that this technique is most sensitive to cirrus optical depth in the 10 (micro)m window of 0.1-0.15 or greater over the tropical and subtropical oceans, where surface emissivity and skin/near-surface air temperature impacts on the IR radiances are minimal. The method at present is generally valid over oceanic regions only, specifically, the tropics and subtropics. The detection of thin cirrus, and other cloud types, is validated using observations at the Atmospheric Radiation Measurement (ARM) program site located at Manus Island in the tropical western Pacific for 89 coincident EOS-Aqua overpasses. Even though the emphasis of this work is on the detection of thin cirrus at nighttime, this technique is sensitive to a broad cloud morphology. The cloud detection technique agrees with ARM-detected clouds 82-84% of the time, which include thin cirrus, as well as other cloud types. Most of the disagreements are well explained by AIRS footprint-scale heterogeneity compared to ARM point measurements, cirrus overlying lower-layer water clouds, possible mixed phase microphysics in midlevel clouds, and significant IR channel noise for cold BT scenes over deep convective towers.

Atmospheric Radiation Measurement (RAM)↗

NASA NTRS1996

On flow phenomena that emit X-rays in hot star winds

The X-ray emission from O stars may originate from instability-generated shocks in their stellar winds. Previous numerical simulations that assumed the wind to be isothermal could only draw limited conclusions concerning this emission. Calculations that include the energy transfer in the wind are presented. They confirm that up to a few stellar radii, radiative cooling is efficient which implies that the shock cooling zones are short in comparison with the dynamical lengths. At larger radii, the wind structure changes as all the shocks are destroyed due to a broadening of their cooling zones. The following flow phenomena are discussed as possible X-ray sources: inner radiative shock; shock merging, outer adiabatic shocks, remaining hot gas from shock destruction, and an outer corona.

Feldmeier, A.↗

NASA NTRS2001

GCM Simulations of the Aerosol Indirect Effect: Sensitivity to Cloud Parameterization and Aerosol Burden

We describe the coupling of the Goddard Institute for Space Studies (GISS) general circulation model (GCM) to an online sulfur chemistry model and source models for organic matter and sea-salt that is used to estimate the aerosol indirect effect. The cloud droplet number concentration is diagnosed empirically from field experiment datasets over land and ocean that observe droplet number and all three aerosol types simultaneously; corrections are made for implied variations in cloud turbulence levels. The resulting cloud droplet number is used to calculate variations in droplet effective radius, which in turn allows us to predict aerosol effects on cloud optical thickness and microphysical process rates. We calculate the aerosol indirect effect by differencing the top-of-the-atmosphere net cloud radiative forcing for simulations with present-day vs. pre-industrial emissions. Both the first (radiative) and second (microphysical) indirect effects are explored. We test the sensitivity of our results to cloud parameterization assumptions that control the vertical distribution of cloud occurrence, the autoconversion rate, and the aerosol scavenging rate, each of which feeds back significantly on the model aerosol burden. The global mean aerosol indirect effect for all three aerosol types ranges from -1.55 to -4.36 W/sq m in our simulations. The results are quite sensitive to the pre-industrial background aerosol burden, with low pre-industrial burdens giving strong indirect effects, and to a lesser extent to the anthropogenic aerosol burden, with large burdens giving somewhat larger indirect effects. Because of this dependence on the background aerosol, model diagnostics such as albedo-particle size correlations and column cloud susceptibility, for which satellite validation products are available, are not good predictors of the resulting indirect effect.

Menon, Surabi↗

NASA NTRS1974

Effect of pollutant gases on ozone production by simulated solar radiation

The present investigation provides some information related to the problem of ozone destruction by nitric oxide emission from high flying vehicles. It is found that CO and H2O can counteract NO destruction of O3 in laboratory simulations. The addition of CO and H2O to aircraft exhausts could be a practical means of reducing the damage of the UV-filtering ozone layer. It is also discovered that NO is not regenerated as it destroys ozone, except at low stratospheric pressures. It is believed that the presence of H2O and CO gives rise to a series of reactions which provide a kinetically competitive pathway for the NO, causing it to go into NO2 production via these substrates rather than via O3.

Wong, E. L.↗

NASA NTRS1964

Temperature dependence of the solar absorptance and thermal emittance of copper, gold, nickel, and silver.

Solar absorptance and thermal emittance of copper, gold, nickel and silver as function of temperature

THERMAL EMISSION↗

NASA NTRS1976

Experimental clean combustor program, alternate fuels addendum, phase 2

The characteristics of current and advanced low-emissions combustors when operated with special test fuels simulating broader range combustion properties of petroleum or coal derived fuels were studied. Five fuels were evaluated; conventional JP-5, conventional No. 2 Diesel, two different blends of Jet A and commercial aromatic mixtures - zylene bottoms and haphthalene charge stock, and a fuel derived from shale oil crude which was refined to Jet A specifications. Three CF6-50 engine size combustor types were evaluated; the standard production combustor, a radial/axial staged combustor, and a double annular combustor. Performance and pollutant emissons characteristics at idle and simulated takeoff conditions were evaluated in a full annular combustor rig. Altitude relight characteristics were evaluated in a 60 degree sector combustor rig. Carboning and flashback characteristics at simulated takeoff conditions were evaluated in a 12 degree sector combustor rig. For the five fuels tested, effects were moderate, but well defined.

Gleason, C. C.↗

NASA NTRS1981

Small gas-turbine combustor study: Fuel injector evaluation

As part of a continuing effort at the Lewis Research Center to improve performance, emissions, and reliability of turbine machinery, an investigation of fuel injection technique and effect of fuel type on small gas turbine combustors was undertaken. Performance and pollutant emission levels are documented over a range of simulated flight conditions for a reverse flow combustor configuration using simplex pressure-atomizing, spill-flow return, and splash cone airblast injectors. A parametric evaluation of the effect of increased combustor loading with each of the fuel injector types was obtained. Jet A and an experimental referee broad specification fuel were used to determine the effect of fuel type.

Norgren, C. T.↗

NASA NTRS1981

Small gas-turbine combustor study - Fuel injector evaluation

As part of a continuing effort at the Lewis Research Center to improve performance, emissions, and reliability of turbine machinery, an investigation was undertaken to determine the effect of fuel injection technique and fuel type on similar improvements for small gas-turbine combustors. Performance and pollutant emission levels are documented over a range of simulated flight conditions for a reverse-flow combustor configuration using simplex pressure-atomizing, spill-flow return, and splash cone airblast injectors. A parametric evaluation of the effect of increased combustor loading with each of the fuel injector types was obtained. Jet A and an experimental referee broad specification fuel were used to determine and compare effects of burning different types of fuels in a small experimental gas turbine combustor.

Norgren, C. T.↗

NASA NTRS1985

Small gas turbine combustor study: Fuel injector performance in a transpiration-cooled liner

The effect of fuel injection technique on the performance of an advanced reverse flow combustor liner constructed of Lamilloy (a multilaminate transpiration type material) was determined. Performance and emission levels are documented over a range of simulated flight conditions using simplex pressure atomizing, spill return, and splash cone airblast injectors. A parametric evaluation of the effect of increased combustor loading with each of the fuel injector types is obtained.

Riddlebaugh, S. M.↗

NASA NTRS1985

Small gas turbine combustor study - Fuel injector performance in a transpiration-cooled liner

Riddlebaugh, S. M.↗