Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polycrystalline material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Reduced synthesis temperatures of SrNbO 2 N perovskite films for photoelectrochemical fuel production

Perovskite oxynitrides, such as SrNbO 2 N, have been shown to be promising materials for photoanodes in tandem photoelectrochemical cells, due to their suitable bandgap and charge transport. However, thin film synthesis and characterization of oxynitride perovskites are challenging due to high processing temperatures that are incompatible with available substrates. In this work, we report on reduced synthesis temperatures of SrNbO 2 N perovskite thin films on Si substrates across a range of chemical compositions. Polycrystalline thin films with perovskite crystal structure are obtained by sputtering at ambient temperature and annealing at 550-600 degrees C. The perovskite structure has a relatively broad range of cation composition between 50 and 60% Sr with varying O/N ratio according to Rutherford backscattering spectrometry. The maximum photocurrent density was obtained at 55 cation % of Sr, which is slightly Sr-rich compared to the nominal SrNbO 2 N stoichiometry. This work shows the importance of considering cation and anion composition in studying oxynitride perovskites for solar fuel applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Tailoring the Thickness‐Dependent Optical Properties of Conducting Nitrides and Oxides for Epsilon‐Near‐Zero‐Enhanced Photonic Applications

Abstract The unique properties of the emerging photonic materials, conducting nitrides and oxides, especially their tailorability, large damage thresholds, and, importantly, the so‐called epsilon‐near‐zero (ENZ) behavior, have enabled novel photonic phenomena spanning optical circuitry, tunable metasurfaces, and nonlinear optical devices. This work explores direct control of the optical properties of polycrystalline titanium nitride (TiN) and aluminum‐doped zinc oxide (AZO) by tailoring the film thickness, and their potential for ENZ‐enhanced photonic applications. This study demonstrates that TiN–AZO bilayers support Ferrell–Berreman modes using the thickness‐dependent ENZ resonances in the AZO films operating in the telecom wavelengths spanning from 1470 to 1750 nm. The bilayer stacks also act as strong light absorbers in the ultraviolet regime using the radiative ENZ modes and the Fabry–Perot modes in the constituent TiN films. The studied Berreman resonators exhibit optically induced reflectance modulation of 15% with picosecond response time. Together with the optical response tailorability of conducting oxides and nitrides, using the field enhancement near the tunable ENZ regime can enable a wide range of nonlinear optical phenomena, including all‐optical switching, time refraction, and high‐harmonic generation.

Saha, Soham↗
DOE OSTI2022

Scalable Al 2 O 3 –TiO 2 Conductive Oxide Interfaces as Defect Reservoirs for Resistive Switching Devices

Abstract Resistive switching devices herald a transformative technology for memory and computation, offering considerable advantages in performance and energy efficiency. Here, a simple and scalable material system of conductive oxide interfaces is employed, and their unique properties are leveraged for a new type of resistive switching device. An Al 2 O 3 –TiO 2 ‐based valence‐change resistive switching device, where the conductive oxide interface serves both as the bottom electrode and as a reservoir of defects for switching, is demonstrated. The amorphous–polycrystalline Al 2 O 3 –TiO 2 conductive interface is obtained following the technological path of simplifying the fabrication of the 2D electron gases (2DEGs), making them scalable for practical mass integration. Physical analysis of the device chemistry and microstructure with comprehensive electrical analysis of its switching behavior and performance is combined. The origin of the resistive switching is pinpointed to the conductive oxide interface, which serves both as the bottom electrode and as a reservoir of oxygen vacancies. The latter plays a key role in valence‐change resistive switching devices. The new device, based on scalable and complementary metal–oxide–semiconductor (CMOS)‐technology‐compatible fabrication processes, opens new design spaces toward increased tunability and simplification of the device selection challenge.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Laser, vacuum and gas reaction chamber for operando measurements at NSLS-II's 28-ID-2

We present a laser reaction chamber that we have developed for in situ/operando X-ray diffraction measurements at the NSLS-II 28-ID-2 X-ray powder diffraction beamline. This chamber allows for rapid and dynamic sample heating under specialized gas environments, spanning ambient conditions down to vacuum pressures. We demonstrate the capabilities of this setup through two applications: laser-driven heating in polycrystalline iron oxide and in single-crystal WTe 2 . Our measurements reveal the ability to resolve chemical reaction kinetics over minutes with 1 s time resolution. This setup advances opportunities for in situ/operando X-ray diffraction studies of both bulk and single-crystal materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Magnetocaloric Effect in Lightly‐Doped Fe 5 Si 3 Single Crystals

Abstract Development of promising new materials for above room temperature magnetic cooling applications relies on careful balancing of structure and composition to maximize accessible metastable phases that can drive a strong magnetocaloric effect (MCE). However, the working temperatures of these materials may fall outside of desired application windows. In this work, it is shown that it is possible to control metastable phase stability temperatures of Fe 5 Si 3 through selection of appropriate spin and charge doping. Here, the parent material's desired structure appears only within a narrow temperature range from 1098 to 1303 K. Doping with Mn and P is shown to allow stabilization of the parent's high temperature phase and resulting MCE to room temperature. The structural and magnetic properties, and the magnetocaloric effect of single crystal Fe 4.83 Mn 0.16 Si 2.91 P 0.09 (FMSP) are investigated experimentally and theoretically. A first‐order magneto‐elastic transition is observed at 348 K, where magnetic onset is accompanied by a change in lattice volume without an apparent change in crystal symmetry. Although the trace Mn and P doping are found to decrease the T C , the maximum magnetic entropy change Δ S Max ( T ) and the relative cooling power (RCP) of FMSP are enhanced compared to polycrystalline Fe 5 Si 3 . As a result, an intrinsically broader entropy change over a larger temperature span is generated in the lightly doped single crystal of Fe 5 Si 3 . The magnetic moment of the system is also enhanced. Density functional theory (DFT) calculations are performed to gain microscopic insights into the experimental findings. The results suggest that the hexagonal Fe 5 Si 3 is a new giant room temperature MCE material that is on par with La–Fe–Si and Fe‐Mn‐P‐Si systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Triple junction solute segregation in Al-based polycrystals

Solute segregation is a crucial means of stabilizing nanostructured alloys, and at very small grain sizes, this requires consideration of triple junctions (TJs), which attain a meaningful volume fraction and thus become relevant for bulk material behavior. Here, in this study, the solute segregation spectra for grain boundary (GB) and TJ sites are calculated for a large number of dilute Al-based binary systems with available interatomic potentials. A defect-identifying algorithm is applied to quantify the average GB thickness and classify the intergranular site spectra into GB and junction subspectra. The algorithm is also applied to a hybrid electronic-level database for GB segregation of various solutes in Al, yielding polycrystalline TJ solute segregation spectra from first principles. The results suggest that TJ segregation is alloy or interatomic potential dependent and can exhibit either boundary or junction preference. With these spectra as inputs, the spectral GB segregation model gives quantitative predictions of segregation as a function of grain size, temperature, and total solute concentration, suitable for alloy screening and design.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Observation and Characterization of Vibrationally Active Surface Species Accessed with Nonthermal Nitrogen Plasmas

Polycrystalline Ni, Pd, Cu, Ag, and Au foils exposed to nonthermal plasma (NTP)-activated N 2 are found to exhibit a vibrational feature near 2200 cm –1 in polarization-modulation infrared reflection-absorption spectroscopy (PM-IRAS) observations that are not present in the same materials exposed to N 2 under nonplasma conditions. The feature is similar to that reported elsewhere and is typically assigned to chemisorbed N 2 . We employ a combination of temperature-dependent experiments, sequential dosing, X-ray photoelectron spectroscopy, isotopic labeling, and density functional theory calculations to characterize the feature. Results are most consistent with a triatomic species, likely NCO, with the C and O likely originating from ppm-level impurities in the ultrahigh-purity (UHP) Ar and/or N 2 gas cylinders. Here, this work highlights the potential for nonthermal plasmas to access adsorbates inaccessible thermally as well as the potential contributions of ppm-level impurities to corrupt the interpretation of plasma catalytic chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Bounds on the Rate-Dependent Plastic Flow of Tantalum up to 75 GPa

In this study we report on the continued development of thermodynamics-based analysis of shock waves propagation with the objective of extracting information related to materials strength at high strain rates and pressures. Building on previous results reported for peak stresses of 10 GPa and 25 GPa, we present a series of three-step gas-gun shock experiments designed to explore the pressure and strain rate dependence of plastic flow in polycrystalline tantalum. These experiments at nominal peak stresses of 50 GPa and 75 GPa show the irreversible deformation before pullback to be almost entirely confined to the shock loading, with negligible plastic relaxation on the post-shock plateau. We also add a reverse-ballistics shot at 25 GPa, which was designed to reveal the pullback response with negligible interference from free-surface effects. General thermodynamic considerations allow us to place bounds on the plastic behavior even for parts of the curve that change far too rapidly for the velocimetric time resolution of (conservatively) ~ 5 ns. To analyze the data, we found it necessary to substantially improve the interpolation/extrapolation scheme in order to improve its robustness, flexibility and range of applicability. We describe the new scheme based on splines, as well as an extension of free-surface corrections to the post-shock rarefaction waves. Reanalysis with the new scheme produces results essentially within the error bars previously reported, showing that the known systematic errors associated with free-surface effects are relatively inconsequential for determining thermodynamic paths.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

A phase-field model for non-isothermal phase transformation and plasticity in polycrystalline yttria-stabilized tetragonal zirconia

Here we propose an elastoplastic phase-field (PF) model to investigate the mechanics of tetragonal-to-monoclinic phase transformation (TMPT) and elastoplastic deformation of polycrystalline yttria-stabilized tetragonal zirconia (YSTZ). A Landau polynomial with non-vanishing chemical energy at the equilibrium temperature is introduced to account for the actual formation energies of the phases. The effects of different grain orientations, latent heat, and temperature on TMPT and deformation mechanisms are considered. The suppressive transformation effects of the grain boundaries (GBs) is modeled using an inhomogeneous kinetic coefficient in the bulk and GBs. The simulation results for single crystals demonstrate the capability of the model to reproduce the orientation-dependent compressive deformation of YSTZ similar to atomistic simulations and micropillar experiments. The single crystal with [100] crystallographic orientation along the loading direction (SC[100]) displays both TMPT and plasticity, SC[101] experiences only phase transformation, while SC[001] undergoes only plastic yielding. The TMPT induced by compressive loading exhibits shape memory effect (SME) below the equilibrium transformation temperature and pseudoelasticity above it, while the critical transformation stress increases with increasing loading temperature. The irrecoverable plastic strain is found to trap a part of the monoclinic phase, which prevents a complete reverse transformation. The polycrystalline cases also display SME and PE at low and high temperatures, respectively. Due to the orientation differences between grains and the stress concentrations at geometric nonlinearities, plastic deformation occurs in polycrystalline YSTZ for an applied load less than the yield stress. The results suggest a possible limitation of plasticity and an improvement of the shape recovery of YSTZ if one can control the orientation of the grains and/or increase the density of stacking faults at the GBs during material processing.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The Role of Local Inhomogeneities on Dendrite Growth in LLZO-Based Solid Electrolytes

The majority of the ceramic solid electrolytes (LLZO, LATP) demonstrate polycrystalline grain/grain-boundary (G/GB) microstructure. Higher lithium (Li) concentration and lower mechanical stiffness result in current focusing at the GBs. Growth of Li dendrites through local inhomogeneities and subsequent short circuit of the cell is a major concern. Recent studies have revealed that bulk Li metal is a viscoplastic material that has low (~0.3 MPa) and high (~1.0 MPa) yield strength during deformation at smaller and larger rates of strain, respectively. It has been argued that during deposition at smaller current densities, due to its lower yield strength, Li metal should demonstrate plastic flow against stiff ceramic electrolytes, and Li dendrites will be prevented from penetrating through solid electrolytes. In this manuscript, a multiscale modeling framework has been developed for predicting properties of GBs and the bulk of ceramic electrolytes using atomistic calculations for input to mesoscale models. Using the parameters obtained from the atomistic simulations, the mesoscale model reveals that, given enough time, even at low charge rates, lithium dendrites can grow through the GBs of LLZO. The present multiscale model results also provide information regarding the dendrite growth velocity through LLZO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Method and system for preparing polycrystalline group III metal nitride

A process of preparing polycrystalline group III nitride chunks comprising the steps of (a) placing a group III metal inside a source chamber; (b) flowing a halogen-containing gas over the group III metal to form a group III metal halide; (c) contacting the group III metal halide with a nitrogen-containing gas in a deposition chamber containing a foil, the foil comprising at least one of Mo, W, Ta, Pd, Pt, Ir, or Re; (d) forming a polycrystalline group III nitride layer on the foil within the deposition chamber; (e) removing the polycrystalline group III nitride layer from the foil; and (f) comminuting the polycrystalline group III nitride layer to form the polycrystalline group III nitride chunks, wherein the removing and the comminuting are performed in any order or simultaneously.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Predicting Quantum Criticality in Single-Crystalline Ce 2 Ru 3 Ge 5

Strongly correlated f-electron systems are known to host exotic quantum states, such as quantum criticality, complex order parameters, and unconventional superconductivity. However, the appearance of these exotic states is difficult to predict, making the study of quantum critical behavior challenging, especially in ferromagnetic materials. Herein, we report a structure–property map for Ce 2 M 3 X 5 (M = transition metal; X = main group element) that aids in the targeted design of materials likely to exhibit quantum criticality. Guided by this map, we report on the synthesis of single-crystalline Ce 2 Ru 3 Ge 5 and provide, for the first time, magnetic susceptibility, heat capacity, resistivity, and magnetoresistance measurements on single crystals. Here, we observe a weak ferromagnetic-like response at 7.5 K, which is contrasted with the bulk ferromagnetic ordering that appears in polycrystalline samples. Non-Fermi liquid behavior is seen in the temperature dependent electrical resistivity and heat capacity of the single crystals, suggesting proximity to a ferromagnetic quantum critical point without chemical or physical pressure. Given the contrast with previous reports of polycrystals, these results lead us to propose that single crystalline Ce 2 Ru 3 Ge 5 is intrinsically tuned into the vicinity of a ferromagnetic quantum critical point.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multi-scale boron penetration toward stabilizing nickel-rich cathode

Nickel-rich layered oxides LiNi x Co y Mn 1-x-y O 2 (x≥0.8) have been recognized as the preferred cathode materials to develop lithium-ion batteries with high energy density (>300Wh kg -1 ). However, the poor cycling stability and rate capability stemming from intergranular cracks and sluggish kinetics hinder their commercialization. To address such issues, a multi-scale boron penetration strategy is designed and applied on the polycrystalline LiNi 0.83 Co 0.11 Mn 0.06 O 2 particles that are pre-treated with pore construction. The lithium-ion conductive lithium borate in grain gaps functions as the grain binder that can bear the strain/stress from anisotropic contraction/expansion, and provides more pathways for lithium-ion diffusion. As a result, the intergranular cracks are ameliorated and the lithium-ion diffusion kinetics is improved. Moreover, the coating layer separates the sensitive cathode surface and electrolyte, helping to suppress the parasitic reactions and related gas evolution. In addition, the enhanced structural stability is acquired by strong B-O bonds with trace boron doping. As a result, the boron-modified sample with an optimized boron content of 0.5% (B5-NCM) exhibits a higher initial discharge capacity of 205.5mAh g -1 at 0.1C (1C=200mA g -1 ) and improved capacity retention of 81.7% after 100 cycles at 1C. Furthermore, the rate performance is distinctly enhanced by high lithium-ion conductive LBO (175.6mAh g -1 for B5-NCM and 154.6mAh g -1 for B0-NCM at 5C).

25 ENERGY STORAGE↗
DOE OSTI2021

Phase transformations, microstructural refinement and defect evolution mechanisms in Al-Si alloys under non-hydrostatic diamond anvil cell compression

Non-hydrostatic compression of materials using a diamond anvil cell (DAC) can transform equilibrium microstructure of an alloy to novel, potentially metastable states. In this study, in situ synchrotron X-ray diffraction (XRD) during compression up to 24 GPa and subsequent ex situ, high resolution analytical electron microscopy (AEM) after decompression of an Al-Si alloy provided insight into the crystallographic changes during the compression as well as microstructural refinement, and defect structures caused by such a high pressure compression-decompression process. Pressure resolved in-situ synchrotron XRD was used to detail the phase transformation pathway of the eutectic Si phase in Al-Si alloy, from Si-I → Si-XI → Si-V during compression, and a final transformation predominantly to Si-III after decompression. Using scanning and transmission electron microscopy (S/TEM), site specific analysis of the alloy immediately underneath the anvil contact surface demonstrated a highly complex microstructure. A narrow region of thick amorphous Al oxide interspersed with nanocrystalline grains was found at the top surface. Underneath this Al oxide, while the majority the eutectic Si was transformed into highly-deformed, polycrystalline (PC) Si-III, a complex intermediate layer was discovered at the interface between Al and Si, comprised of a small fraction of Al nanocrystals and a majority of nanocrystalline Si-I. This combination of pressure resolved in-situ synchrotron XRD coupled with subsequent high resolution, electron microscopy resolved the phase transformation as well as non-equilibrium microstructures in a metallic alloy induced by a non-hydrostatic high pressure compression followed by decompression.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A Continuum Dislocation Dynamics Crystal Plasticity Approach to Irradiated Body-Centered Cubic α-Iron

Radiation-induced embrittlement of reactor pressure vessel (RPV) steels can potentially limit the operating life of nuclear power plants. Over extended exposure to radiation doses, these body-centered cubic (BCC) irons demonstrate irradiation damage. Here, we present a continuum dislocation density (CDD) crystal plasticity model to capture the interaction among dislocations and self-interstitial atom (SIA) loops in α-iron. We demonstrate the importance of modeling cross slip using a combined stochastic Monte Carlo approach and the role of slip system strength anisotropy in capturing stochastic cross slip interactions. Through these captured interactions, the CDD crystal plasticity model can capture both the stress response and the physical evolution of dislocations on different slip system planes. Single-crystal verification experiments are used to calibrate the CDD crystal plasticity model, and a set of simplified polycrystalline simulations demonstrates the model’s ability to capture the stress response from tensile experiments on α-iron.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ temperature profile measurements with high-energy X-rays as a probe of optical floating zone crystal growth environment

The ability of optical floating zone (OFZ) furnaces to rapidly produce large single crystals of complex emerging materials has had a transformative effect on many scientific fields that require samples of this type. However, the crystal growth process within the OFZ furnace is not well understood owing to the challenges involved in monitoring the high-temperature crystal growth process. Novel beamline-compatible optical furnaces that approximate the inhomogeneous growth environment within an OFZ furnace have been fabricated and tested in high-energy synchrotron beamlines. In this paper, it is demonstrated that temperature profiles can be effectively extracted from powder diffraction data collected on polycrystalline ceramic rods heated at their tip. Furthermore, these measured temperature profiles can be accurately reproduced using a heat-transfer model that accounts for solid-state thermal conduction, partial sample lamp power absorption, convective air cooling and radiative cooling, allowing key thermal parameters such as thermal conductivity to be extracted from experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Image-based modeling of coupled electro-chemo-mechanical behavior of Li-ion battery cathode using an interface-modified reproducing kernel particle method

Abstract An interface-modified reproducing kernel particle method (IM-RKPM) is introduced in this work to allow for a direct model construction from image pixels of heterogeneous polycrystalline Li-ion battery microstructures. The interface-modified reproducing kernel (IM-RK) approximation is constructed through scaling of a kernel function by a regularized distance function in conjunction with strategic placement of interface node locations. This leads to RK shape functions with either weak or strong discontinuities across material interfaces, suitable for modeling various interface mechanics. With the placement of a triple junction node and distance-based scaling of kernel functions, the resulting IM-RK shape function also possesses proper discontinuities at the triple junctions. This IM-RK approximation effectively remedies the well-known Gibb’s oscillation in the smooth approximation of discontinuities. Different from the conventional meshfree approaches for interface discontinuities, this IM-RK approach is done without additional degrees of freedom associated with the enrichment functions, and it is formulated with the standard procedures in the RK shape function construction. This work focuses on identifying the accuracy and convergence properties of IM-RKPM for modeling the coupled electro-chemo-mechanical system. A linear patch test is formulated and numerically tested for the electro-chemo-mechanical coupled problem with a Butler–Volmer boundary condition representing the physical conditions in Li-ion battery microstructures. This is followed by verification of the optimal rates of convergence of IM-RKPM for solving the coupled problem with higher order solutions. The image-based modeling of Li-ion battery microstructures in the numerical examples demonstrates the applicability of the proposed method to realistic Li-ion battery materials modeling.

25 ENERGY STORAGE↗