Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “plastic strains”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Plastic homogeneity in nanoscale heterostructured binary and multicomponent metallic eutectics: An overview

Heterostructured materials comprised of relatively soft/hard disparate phases typically exhibit composite strengthening but lack plastic deformability at ambient temperatures. However, heterostructured systems comprised of nanoscale phases can simultaneously enhance yield strength and strain hardening, thereby promoting uniform distribution of plastic flow. In this review, the atomic-scale deformation mechanisms in model systems of eutectic alloys, Al-Al 2 Cu and Al-Si, refined to nanoscales via laser rapid solidification are discussed, and compared with literature on multi-component (high entropy) eutectics such as Ni-Al-Fe-based with Cr and/or Co additions. The nano-lamellar Al-Al 2 Cu structures exhibit unit defect mechanisms not reported in monolithic Al 2 Cu intermetallic: localized shear on {0 1 1} and shear-induced faults on {1 2 1} planes, constrained by closely-spaced dislocation arrays in Al confined by Al/Al 2 Cu interfaces. The unexpected plasticity mechanisms are enabled by slip continuity in nanoscale Al-Al 2 Cu eutectics associated with the orientation relationship and interface habit planes. In nano-fibrous Al-Si eutectic, tensile ductility at strength approaching 600 MPa is observed resulting from dislocation plasticity in the nano-Al channels and cracking in Si nanofibers. Molecular dynamics simulations show that Al dislocations easily cross-slip (screw) or climb (edge) along Al-Si interfaces, making slip transmission difficult. The propagation of nano-cracks is suppressed by surrounding strain hardening Al, retaining good ductility of the sample, in spite of lack of direct slip transmission. Finally, the critical unit mechanisms of slip transmission and interface-enabled plasticity observed in nanoscale eutectic binary systems can also explain the strength-ductility relationship in multi-component eutectics and homogeneously distributed plastic flow with increasing microstructural heterogeneity.

36 MATERIALS SCIENCE↗
NASA NTRS2014

Characterization of Plastic Degrading Bacteria from Environmental Samples by Genetic and Biochemical Analysis

Plastic is the major waste-product during NASA space missions, recycling this waste-stream to produce other beneficial materials would decrease upmass. Bacterial called plastisomes have been demonstrated to metabolize non-biodegradable plastics such as polyethylene and polystyrene. Characterization and engineering of these bacteria, and their eventual incorporation as life support systems would enable space flight beyond lower earth orbit. We will utilize molecular techniques to identify and isolate the most productive plastisome. Environmental samples obtained from locations known to be rich in plastic will be cultured in a laboratory defined-media supplemented with plastic as the sole carbon source. Cultures will be monitored for growth over time. Ribosomal DNA will be amplified from cultures that exhibit growth using PCR. These amplified fragments will be sequenced to determine the identity of the consortia in the cultures. We will then perform bioinformatics analysis on the data to identify the plastisomes and generate phylogenetic trees. Morphological and physiological profile of the plastisomes will also be conducted by microscopy and biochemical tests. Our results would reveal a bacterial strain that can break down plastics efficiently. The implication for this project would not only benefit space exploration but also make a major impact towards sustainability development on Earth.

plastic conversion↗
DOE OSTI2021

Techniques for studying materials under extreme states of high energy density compression

The properties of materials under extreme conditions of pressure and density are of key interest to a number of fields, including planetary geophysics, materials science, and inertial confinement fusion. In geophysics, the equations of state of planetary materials, such as hydrogen and iron, under ultrahigh pressure and density provide a better understanding of their formation and interior structure [Celliers et al., “Insulator-metal transition in dense fluid deuterium,” Science 361, 677–682 (2018) and Smith et al., “Equation of state of iron under core conditions of large rocky exoplanets,” Nat. Astron. 2, 591–682 (2018)]. The processes of interest in these fields occur under conditions of high pressure (100 GPa–100 TPa), high temperature (>3000 K), and sometimes at high strain rates (>103 s−1) depending on the process. With the advent of high energy density (HED) facilities, such as the National Ignition Facility (NIF), Linear Coherent Light Source, Omega Laser Facility, and Z, these conditions are reachable and numerous experimental platforms have been developed. To measure compression under ultrahigh pressure, stepped targets are ramp-compressed and the sound velocity, measured by the velocity interferometer system for any reflector diagnostic technique, from which the stress-density of relevant materials is deduced at pulsed power [M. D. Knudson and M. P. Desjarlais, “High-precision shock wave measurements of deuterium: Evaluation of exchange-correlation functionals at the molecular-to-atomic transition,” Phys. Rev. Lett. 118, 035501 (2017)] and laser [Smith et al., “Equation of state of iron under core conditions of large rocky exoplanets,” Nat. Astron. 2, 591–682 (2018)] facilities. To measure strength under high pressure and strain rates, experimenters measure the growth of Rayleigh–Taylor instabilities using face-on radiography [Park et al., “Grain-size-independent plastic flow at ultrahigh pressures and strain rates,” Phys. Rev. Lett. 114, 065502 (2015)]. The crystal structure of materials under high compression is measured by dynamic x-ray diffraction [Rygg et al., “X-ray diffraction at the national ignition facility,” Rev. Sci. Instrum. 91, 043902 (2020) and McBride et al., “Phase transition lowering in dynamically compressed silicon,” Nat. Phys. 15, 89–94 (2019)]. Medium range material temperatures (a few thousand degrees) can be measured by extended x-ray absorption fine structure techniques, Yaakobi et al., “Extended x-ray absorption fine structure measurements of laser-shocked V and Ti and crystal phase transformation in Ti,” Phys. Rev. Lett. 92, 095504 (2004) and Ping et al., “Solid iron compressed up to 560 GPa,” Phys. Rev. Lett. 111, 065501 (2013), whereas more extreme temperatures are measured using x-ray Thomson scattering or pyrometry. This manuscript will review the scientific motivations, experimental techniques, and the regimes that can be probed for the study of materials under extreme HED conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Pseudoelasticity of SrNi2P2 Micropillar via Double Lattice Collapse and Expansion

The maximum recoverable strain of most crystalline solids is less than 1% because plastic deformation or fracture usually occurs at a small strain. In this work, we show that a SrNi 2 P 2 micropillar exhibits pseudoelasticity with a large maximum recoverable strain of ~14% under uniaxial compression via unique reversible structural transformation, double lattice collapse–expansion that is repeatable under cyclic loading. Its high yield strength (~3.8 ± 0.5 GPa) and large maximum recoverable strain bring out the ultrahigh modulus of resilience (~146 ± 19 MJ/m 3 ), a few orders of magnitude higher than that of most engineering materials. The double lattice collapse–expansion mechanism shows stress–strain behaviors similar to that of conventional shape-memory alloys, such as hysteresis and thermo-mechanical actuation, even though the structural changes involved are completely different. Our work suggests that the discovery of a new class of high-performance ThCr 2 Si 2 -structured materials will open new research opportunities in the field of pseudoelasticity.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
NASA NTRS1999

Anisotropic Plasticity of BN Nanotubes

Plastic collapse of compressed BN nanotubes are investigated and compared with carbon nanotubes of similar nature. Using a generalized tight-binding molecular dynamics (GTBMD) method for system containing B, N and C atoms we compute stiffness and plastic collapse of BN and C nanotubes under axial compression. For small compressional strain, BN nanotubes are found to be about 92% as stiff as similar C nanotubes. Due to BN bond buckling effect, however, the elastic limit of BN nanotubes is found to be more than C nanotubes. A route to plasticity is explored in which we find that at elastic limit the accumulated strain is released by a local plastic deformation of the nanotube. The mechanism of strain release and the resulting plastic deformation, however. are anisotropic in nature. The strain is released preferentially towards N as leading edge of a buckled BN bond and the tube, compressed at both ends, plastically collapses preferentially towards one end. Details of the anisotropic plasticity and prospective applications will be discussed in this presentation.

Madhu, Menon↗
DOE OSTI2025

Green's function fast multipole method for continuum mechanics (SM-FMM)

Solid Mechanics Fast Multipole Method based on elastic Green's function and accelerated using FFTs The code calculates the mechanical fields (stress and strain) for a heterogeneous elasto-plastic material unit cell under quasi-static conditions (no dynamic effects). The fields are calculated using a Green's function method, where the strain field is given by a discrete convolution of Green's operator with an auxiliary stress field. The convolution is calculated using the fast multipole method.

Zecevic, Miroslav↗
NASA NTRS1983

Acoustic emission characterization using AE (parameter) delay

The acoustic emission (AE) parameter delay concept is defined as that particular measured value of a parameter at which a specified baseline level of cumulative AE activity is reached. The parameter can be from any of a broad range of elastic, plastic, viscoelastic, and fracture mechanics parameters, as well as their combinations. Such parameters include stress, load, strain, displacement, time, temperature, loading cycle, unloading stress, stress intensity factor, strain energy release rate, and crack tip plasticity zone size, while the AE activity may be AE event counts, ringdown counts, energy, event duration, etc., as well as their combinations. Attention is given to examples for the AE parameter delay concept, together with various correlations.

Williams, J. H., Jr.↗
NASA NTRS1977

Elasto-plastic flow in cracked bodies using a new finite element model

Cracked geometries were studied by finite element techniques with the aid of a new special element embedded at the crack tip. This model seeked to accurately represent the singular stresses and strains associated with the elasto-plastic flow process. The present model was not restricted to a material type and did not predetermine a singularity. Rather the singularity was treated as an unknown. For each step of the incremental process the nodal degrees of freedom and the unknown singularity were found through minimization of an energy-like functional. The singularity and nodal degrees of freedom were determined by means of an iterative process.

Karabin, M. E., Jr.↗
DOE OSTI2023

The mechanism of twin thickening and the elastic strain state of TWIP steel nanotwins

A Twinning Induced Plasticity (TWIP) steel with a nominal composition of Fe-16.4Mn-0.9C-0.5Si-0.05Nb-0.05V was deformed to an engineering strain of 6%. The strain around the deformation twins were mapped using the 4D-STEM technique. Strain mapping showed a large average elastic strain of approximately 6% in the directions parallel and perpendicular to the twinning direction. However, the large average strain comprised of several hot spots of even larger strains of up to 12%. These hot spots could be attributed to a high density of sessile Frank dislocations on the twin boundary and correspond to shear stresses of 1–1.5 GPa. The strain and therefore stress fields are significantly larger than other materials known to twin and are speculated to be responsible for the early thickness saturation of TWIP steel nanotwins. The ability to keep twins extremely thin helps improve grain fragmentation, i.e. the dynamic Hall–Petch effect, and underpins the large elongations and strain hardening rates in TWIP steels.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Enhanced ductility in in-layer glass-carbon fiber/epoxy hybrid composites produced via tailored fiber placement

Experimental mechanical property results of composite materials with hybrid reinforcements (commingled glass and carbon fibers) are detailed and compared with single-fiber composite properties. In-layer hybrid materials, with carbon and glass fiber tows laid side-by-side, were produced via tailored fiber placement (TFP) technology. Detailed experiments showed a phenomenon of “enhanced ductility” of carbon fiber in the hybrid composites of 12–24% relative to an all-carbon fiber composite and multiple stress–strain peaks were observed. Here, this enhanced ductility was hypothesized to be due to the glass fibers mitigating the shock waves arising from the initial failures of carbon fibers, and preventing the premature failure of the remaining carbon fibers. A novel way to engineer the stress–strain behavior of a hybrid composite to achieve a metal-like ductile response (plateau of stress–strain behavior, often termed “elastic–plastic deformation”) was demonstrated by carefully selecting the type and composition of carbon and glass fiber materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Deformation and Fracture Behaviors of Cylindrical Battery Shell During Thermal Runaway

Thermal runaway is one of the catastrophic failure modes of lithium-ion cells. During thermal runaway in cylindrical cells, sidewall shell rupture has been identified as a contributing factor for thermal runaway propagation in battery packs. Herein, the deformation and fracture behaviors of the battery shell during thermal runaway are investigated based on in-situ and ex-situ characterization as well as physics-based modeling. The deformation and fracture modes of the battery shell with/without Carbon Fiber Reinforced Polymer (CFRP) sleeves are identified. In the simulation, the strain introduced by thermal expansion of the system is considered, as well as the thermal and strain rate effects on the plastic stage. The final cell shell modeling is validated by cell thermal runaway tests. Results reveal the quantitative relation between shell deformation behaviors and the pressure and temperature distribution. Both the experiment and model demonstrate the effectiveness of adding a tight-fitting CFRP sleeve around the cell in limiting the side-wall rupture of the shell. The use of CFRP tubes introduces a novel phenomenon in the context of uneven temperature distribution. Results shed light on the mechanistic analysis of a cell side-wall rupture during thermal runaway and provide essential guidance for the next-generation safe battery design.

battery casing↗
DOE OSTI2024

Alloying effects on deformation induced microstructure evolution in copper

In this work, we investigated the effects of alloying elements on plastic deformation and microstructure evolution in polycrystalline copper (Cu) and Cu alloyed with 1 wt. % lead (Cu-1 %Pb). These materials were selected due to the size mismatch between Cu and Pb, with the latter forming precipitates at grain boundaries. Multi-modal characterization techniques, including neutron diffraction, electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM), along with finite element simulations were employed to study the deformation behavior across multiple length scales. While both Cu and Cu-1%Pb exhibited similar macroscale response and final deformation textures, both dislocation line profile analysis and TEM revealed increased dislocation density in deformed Cu-1%Pb specimens. The presence of lead precipitates also significantly affected local plastic deformation during compression, with their influence diminishing with increasing strain. These results demonstrate the complex relationships between alloying elements, plastic deformation, microstructural evolution, and material behavior under load. The insights gained from this multi-scale and multi-technique approach contribute to the fundamental understanding of microstructural evolution in immiscible alloys and are valuable for tailoring the properties of structural materials for specific engineering applications.

36 MATERIALS SCIENCE↗
NASA NTRS1965

Statics of deformable solids.

Text on deformable solid statics including indeterminate systems, strain, stress, elasticity, continuum energy, plasticity and mathematical appendix

STATIC DEFORMATION↗
NASA NTRS1970

Computerized microstrain test system

Design of computerized microstrain test apparatus to measure plastic deformation, hysteresis, and total strain energy at microinch sensitivities

Curran, T. P.↗
NASA NTRS1972

Mathematical characterization of mechanical behavior of porous frictional granular media

A new definition of loading and unloading along the yield surface of Roscoe and Burland is introduced. This is achieved by noting that the strain-hardening parameter in the plastic potential function is deduced from the yield locus equation of Roscoe and Burland. The analytical results are compared with the experimental results for plate-bearing and cone-penetrometer problems and close agreements are demonstrated. The wheel-soil interaction is studied under dynamic loading. The rate-dependent plasticity or viscoelastoplastic behavior is considered. This is accomplished by the internal (hidden) variables associated with time-dependent viscous properties directly superimposed with inelastic behavior governed by the yield criteria of Roscoe and Burland. Effects of inertia and energy dissipation are properly accounted for. Example problems are presented.

Chung, T. J.↗
NASA NTRS1986

Life prediction and constitutive models for engine hot section

The purpose of this program is to develop life prediction models for coated anisotropic materials used in gas turbine airfoils. In the program, two single crystal alloys and two coatings are being tested. These include PWA 1480, Alloy 185, overlay coating (PWA 286), and aluminide coating (PWA 273). Constitutive models are also being developed for these materials to predict the time independent (plastic) and time dependent (creep) strain histories of the materials in the lab tests and for actual design conditions. This nonlinear material behavior is particularly important for high temperature gas turbine applications and is basic to any life prediction system. Some of the accomplishments of the program are highlighted.

Swanson, G. A.↗
NASA NTRS1992

Verification of effective thicknesses for side-grooved compact specimens

The definition of effective thicknesses of the ASTM standard 25 percent side-grooved compact specimens to calculate the elastic compliance, elastic SIF, and elastic-plastic J integral is reevaluated. 3D elastic-plastic analyses of polane-strain, smooth, and 25 percent side-grooved compact specimen models are conducted using the ZIP3D code. Calculated compliance, SIFs, and J-integrals are compared with E-813 solutions.

Shivakumar, Kunigal N.↗
NASA NTRS1999

Crack Growth Prediction Methodology for Multi-Site Damage: Layered Analysis and Growth During Plasticity

A finite element program has been developed to perform quasi-static, elastic-plastic crack growth simulations. The model provides a general framework for mixed-mode I/II elastic-plastic fracture analysis using small strain assumptions and plane stress, plane strain, and axisymmetric finite elements. Cracks are modeled explicitly in the mesh. As the cracks propagate, automatic remeshing algorithms delete the mesh local to the crack tip, extend the crack, and build a new mesh around the new tip. State variable mapping algorithms transfer stresses and displacements from the old mesh to the new mesh. The von Mises material model is implemented in the context of a non-linear Newton solution scheme. The fracture criterion is the critical crack tip opening displacement, and crack direction is predicted by the maximum tensile stress criterion at the crack tip. The implementation can accommodate multiple curving and interacting cracks. An additional fracture algorithm based on nodal release can be used to simulate fracture along a horizontal plane of symmetry. A core of plane strain elements can be used with the nodal release algorithm to simulate the triaxial state of stress near the crack tip. Verification and validation studies compare analysis results with experimental data and published three-dimensional analysis results. Fracture predictions using nodal release for compact tension, middle-crack tension, and multi-site damage test specimens produced accurate results for residual strength and link-up loads. Curving crack predictions using remeshing/mapping were compared with experimental data for an Arcan mixed-mode specimen. Loading angles from 0 degrees to 90 degrees were analyzed. The maximum tensile stress criterion was able to predict the crack direction and path for all loading angles in which the material failed in tension. Residual strength was also accurately predicted for these cases.

James, Mark Anthony↗