SEARCH · Engineering Papers

Results for “oxygen diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

All sources NASA NTRS DOE OSTI

NASA NTRS1961

On the Electron Density Distribution Above the F2 Peak

The distribution of free electrons in an isothermal upper ionosphere consisting of a binary ion mixture (O+ and H+) is discussed. It is shown that for diffusive equilibrium, which should prevail at altitudes well above the F2 peak, measurements of the electron density distribution permit the determination of other structural parameters of the upper atmosphere, such as the temperature and the concentration of oxygen ions and protons.

Bauer, S. J.↗

NASA NTRSDate not supplied

The Effect of Reduced Pressure on the Characteristics of Spreading Flames

Flame spread over solid fuels is a canonical problem in fire science, due to its direct implications on material flammability and importance in fire development. In a microgravity environment, such as onboard a spacecraft, flames can behave very differently than on Earth. This is concerning for spaceflight life safety, especially in higher-oxygen environments. Due to the difficulties associated with microgravity testing, low-pressure environments have been proposed as an alternative to approximately replicate the burning behavior of solid fuels observed in reduced gravity conditions because of similar diffusion and heat transfer mechanisms. However, the roles played by gravity and pressure on flame length, standoff distance, and flame spread rate vary with the burning configuration. In concurrent flame spread, the buoyant flow enhances the spread rate by bringing the flame closer to the fuel surface and increasing the heating of the solid fuel. In opposed flame spread, the sample is preheated by the flame ahead of the flame leading edge, which is strongly affected by the surrounding flow field. In this work, we consider flames spreading over thin cotton samples in both downward (opposed) and upward (concurrent) configurations to investigate the effect of pressure (30-100 kPa) on flame characteristics, such as spread rate and standoff distance. A small forced flow is induced upward so that the flames are exposed to a mixed (forced and free) flow. By reducing pressure, flames become less bright, their standoff distance increases, and their spread rates decrease similar to what is observed in low-gravity environments. These results could in help understanding the differences between flames spreading at low pressure and low gravity environments for these similar, yet very different, spreading configurations. They could also provide more information about potential Earth-based flammability testing of materials for spacecraft applications.

fire safety↗

NASA NTRSDate not supplied

The effect of reduced pressure on the characteristics of spreading flames

fire safety↗

NASA NTRS2001

An Analytical Model for Non-Uniform Magnetic Field Effects on Two-Dimensional Laminar Jet Diffusion Flames

In 1846, Michael Faraday found that permanent magnets could cause candle flames to deform into equatorial disks. He believed that the change in flame shape was caused by the presence of charged particles within the flames interacting with the magnetic fields. Later researchers found that the interaction between the flame ions and the magnetic fields were much too small to cause the flame deflection. Through a force analysis, von Engel and Cozens showed that the change in the flame shape could be attributed to the diamagnetic flame gases in the paramagnetic atmosphere. Paramagnetism occurs in materials composed of atoms with permanent magnetic dipole moments. In the presence of magnetic field gradients, the atoms align with the magnetic field and are drawn into the direction of increasing magnetic field. Diamagnetism occurs when atoms have no net magnetic dipole moment. In the presence of magnetic gradient fields, diamagnetic substances are repelled towards areas of decreasing magnetism. Oxygen is an example of a paramagnetic substance. Nitrogen, carbon monoxide and dioxide, and most hydrocarbon fuels are examples of diamagnetic substances. In order to evaluate the usefulness of these magnets in altering flame behavior, a study has been undertaken to develop an analytical model to describe the change in the flame length of a laminar diffusion jet in the presence of a nonuniform magnetic field.

Calvert, M. E.↗

NASA NTRS2003

Models And Experiments Of Laminar Diffusion Flames In Non-Uniform Magnetic Fields

Non-uniform magnetic fields affect laminar diffusion flames as a result of the paramagnetic and diamagnetic properties of the products and reactants. Paramagnetism is the weak attraction to a magnetic field a material exhibits as a result of permanent magnetic dipole moments in the atoms of the material. Diamagnetism is the weak repulsion to a magnetic field exhibited by a material due to the lack of permanent magnetic dipole moments in the atoms of a material. The forces associated with paramagnetic and diamagnetism are several orders of magnitude less than the forces associated with the more familiar ferromagnetism. A typical example of a paramagnetic gas is oxygen while hydrocarbon fuels and products of combustion are almost always diamagnetic. The fact that magnets can affect flame behavior has been recognized for more than one hundred years. Early speculation was that such behavior was due to the magnetic interaction with the ionized gases associated with a flame. Using a scaling analysis, it was later shown that for laminar diffusion flames the magnetic field/ionized gas interaction was insignificant to the paramagnetic and diamagnetic influences. In this effort, the focus has been on examining laminar diffusion slot flames in the presence of non-uniform upward decreasing magnetic fields produced using permanent magnets. The principal reason for choosing slot flames was mathematical models of such flames show an explicit dependence on gravitational body forces, in the buoyancy-controlled regime, and an applied magnetic field would also impose a body force. In addition, the behavior of such flames was more easily visualized while maintaining the symmetry of the two-dimensional problem whereas it would have been impossible to obtain a symmetric magnetic field around a circular flame and still visually record the flame height and shape along the burner axis. The motivation for choosing permanent magnets to produce the magnetic fields was the assumption that space-related technologies based on the knowledge gained during this investigation would more likely involve permanent magnets as opposed to electromagnets. While no analysis has been done here to quantify the impact that an electric field, associated with an electromagnetic, would have relative to the paramagnetic and diamagnetic interactions, by using permanent magnets this potential effect was completely eliminated and thus paramagnetic and diamagnetic effects were isolated.

Baker, J.↗

NASA NTRS1993

Effects of buoyancy on gas jet diffusion flames

The objective of this effort was to gain a better understanding of the fundamental phenomena involved in laminar gas jet diffusion flames in the absence of buoyancy by studying the transient phenomena of ignition and flame development, (quasi-) steady-state flame characteristics, soot effects, radiation, and, if any, extinction phenomena. This involved measurements of flame size and development, as well as temperature and radiation. Additionally, flame behavior, color, and luminosity were observed and recorded. The tests quantified the effects of Reynolds number, nozzle size, fuel reactivity and type, oxygen concentration, and pressure on flame characteristics. Analytical and numerical modeling efforts were also performed. Methane and propane flames were studied in the 2.2 Second Drop Tower and the 5.18-Second Zero-Gravity Facility of NASA LeRC. In addition, a preliminary series of tests were conducted in the KC-135 research aircraft. Both micro-gravity and normal-gravity flames were studied in this program. The results have provided unique and new information on the behavior and characteristics of gas jet diffusion flames in micro-gravity environments.

Bahadori, M. Yousef↗

NASA NTRS1992

Results of examination of silvered Teflon from the Long Duration Exposure Facility

A significant effort to determine the effects of low earth orbit (LEO) exposure on silver backed fluorinated ethylene-propylene (FEP) blankets from the Long Duration Exposure Facility (LDEF) was performed, and the results of this investigation are described. Extensive measurements of surface, optical, chemical, and mechanical properties were conducted. Effects of contamination and erosion rates of the FEP layer were determined. Specific results are reported on solar absorptance, thermal emittance, diffuse reflectance, cross sectional microphotography, secondary ion mass spectroscopy, electron scattering for chemical analysis, scanning electron microscopy, percent elongation, and tensile strength. These measurements show the effects of two distinctly different exposure environments, solar exposure, and simultaneous atomic oxygen (AO) and solar exposure.

Rousslang, Ken↗

NASA NTRS1993

The scattered solar X-ray background of the ROSAT PSPC

A model for accurately reproducing the light curves and spectra of the scattered solar X-ray background (SB) affecting ROSAT XRT/PSPC pointed observations is presented and demonstrated. This procedure, the modeling and subtraction of the SB, is vital for analysis of all observations of extended X-ray objects and the soft X-ray diffuse background where noncosmic background constituents must be precisely known. At the orbital altitude of ROSAT, about 550 km, and the zenith angles at which the XRT/PSPC observers, 97 deg or less, the scattering is dominated by atomic oxygen with Thomson-scattered X-rays in the 1/4 keV band and oxygen K-alpha fluorescently scattered X-rays at 0.54 keV. This produces field-of-view-integrated minimum count rates in the 0.1-1.0 keV band of about 0.25 counts/s during dayside observations with excursions to about 40 counts/s or more in particularly bad geometries. Typical cosmic background count rates in the same band range from 3 to 12 counts/s, demonstrating the need for the procedure described here.

Snowden, S. L.↗

NASA NTRS1972

JPL lithium doped solar cell development program

One of the most significant problems encountered in the use of silicon solar cells in space is the sensitivity of the device to electron and proton radiation exposure. The p-diffused-into-n-base solar cells were replaced with the more radiation tolerant n-diffused-into-p-base solar cells. Another advancement in achieving greater radiation tolerance was the discovery that the addition of lithium to n-base silicon resulted in what appeared to be annealing of radiation-induced defects. This phenomenon is being exploited to develop a high efficiency radiation resistant lithium-doped solar cell. Lithium-doped solar cells fabricated from oxygen-lean and oxygen-rich silicon were obtained with average initial efficiencies of 11.9% at air mass zero and 28 C, as compared to state-of-the-art n-p cells fabricated from 10 ohm cm silicon with average efficiencies of 11.3% under similar conditions. Lithium-doped cells demonstrated the ability to withstand three to five times the fluence of 1-MeV electrons before degrading to a power equivalent to state-of-the-art solar cells. The principal investigations are discussed with respect to fabrication of high efficiency radiation resistant lithium-doped cells, including starting material, p-n junction diffusion, lithium source introduction, and lithium diffusion.

Berman, P. A.↗

NASA NTRS1973

Moessbauer spectroscopic studies of iron-doped rutile.

Moessbauer spectra were obtained of single crystal and powdered samples of rutile (TiO2) doped to about one percent by weight in isotopically enriched iron. It is shown that the oxidation state may be reversibly altered in situ. After reduction, the oxygen neighbors of the dopant ion are apparently shifted to accomodate the larger ferrous ion. The agreement of calculated quadrupole splittings with experimental results suggests that impurities and oxygen vacancies are uniformly distributed in powdered samples, giving the dopant ions an 'ideal lattice' local environment. The differences between the single crystal and powder sample hyperfine parameters are attributed to variations in stoichiometry, charge compensation mechanisms, or other diffusion related parameters.

Stampfl, P. P.↗

NASA NTRS1976

The response of the ionosphere to the injection of chemically reactive vapors

As a gas released in the ionosphere expands, it is rapidly cooled. When the vapor becomes sufficiently tenuous, it is reheated by collisions with the ambient atmosphere and its flow is then governed by diffusive expansion. As the injected gas becomes well mixed with the plasma, a hole is created by chemical processes. In the case of diatomic hydrogen release, depression of the electron concentrations is governed by the charge exchange reaction between oxygen ions and hydrogen, producing positive hydroxyl ions. Hydroxyl ions rapidly react with the electron gas to produce excited oxygen and hydrogen atoms. Enhanced airglow emissions result from the transition of the excited atoms to lower energy states. The electron temperature in the depleted region rises sharply causing a thermal expansion of the plasma and a further reduction in the local plasma concentration.

Bernhardt, P. A.↗

NASA NTRS1978

Measurement of the turbulence in a gaseous rocket combustion chamber

The intensity of turbulence and the Lagrangian correlation coefficient in a gaseous hydrogen (GH2)-gaseous oxygen (GOX) rocket combustion chamber are studied. A helium tracer gas was injected at an upstream point on the combustion chamber centerline. Samples collected downstream were analyzed for the spreading of the tracer gas concentration. Using Taylor's turbulent diffusion theory and Gosman's numerical method, turbulence parameters were found. In order to evaluate turbulence field inhomogeneity in the axial direction, Taylor's theory was extended. An exponential function was used to approximate the Lagrangian correlation coefficient. It was found that turbulence intensity varies from 15% near the injector to 4% at the nozzle entrance, and that the Lagrangian coefficient rapidly decreases when the dispersion time difference increases.

Tou, P. P.↗

NASA NTRS1986

Far-ultraviolet fluorescence of carbon monoxide in the red giant Arcturus. II - Analysis of high-dispersion IUE spectra

Faint, diffuse emissions near 1380 A in deeply exposed IUE spectrograms of the red giant Arcturus very likely are associated with bands of the A-X fourth-positive system of carbon monoxide, fluoresced by multiplet UV2 of neutral oxygen near 1305 A. Numerical simulations indicate that the strength of the CO bands is exceedingly sensitive, in the best available one-dimensional model of the chromosphere of Arcturus, to a delicate balance between the rapid inward attenuation of the oxygen radiation field and the rapid outward decline of the molecular absorptivity. The fortuitous character of the overlap region in the single-component model argues that one should also consider the possibility that the pumping occurs in a highly inhomogeneous chromosphere, of the type proposed in previous studies of Arcturus based on observations of the infrared absorption bands of CO.

Ayres, T. R.↗

NASA NTRS1987

Small-scale physics of the ocean

Observations and theoretical models of small-scale phenomena in the oceans are reviewed, with a focus on progress during the period 1983-1986. Topics examined include surface layers, equatorial turbulence, off-equator mixed layers, the scaling of mixing, turbulence concepts, laboratory results, internal waves and mixing, rings, the nature of the bottom layer, double diffusion and intrusions, salt fingers, and biological interactions. Also discussed are developments in instrumentation (fast sampling profilers with upward-profiling capability, deep profilers, ship-motion correction, horizontal samplers, small submersibles, submarines, towed packages, conductivity sensors, dissolved-oxygen sensors, and acoustic Doppler current profilers) and goals for future research.

Caldwell, Douglas R.↗

NASA NTRS2002

The Effects of Low Sulfate Concentrations on Modern Microbial Mat Communities: A Long Term Manipulation

Microbial mats were widespread during the first ca. 2 Ga. of our biosphere's history. To better understand microbial ecosystems and their biomarkers under the low sulfate levels present in early oceans, we attempted a long-term (ca. 1 year) manipulation of sulfate in modem mats. Mats collected from salt ponds at Guerrero Negro, Baja Calif. Sur were incubated in a Greenhouse "Collaboratory" at Ames. Mats were maintained in artificial seawater brine containing either: 1) sulfate levels normal for these mats (70 mM), or 2) brine in which sulfate was replaced by chloride. Sulfate concentrations in the "low sulfate" brine gradually approached their lowest (to date) value of 0. 1 mM as sulfate was consumed and/or diffused out of the mat over a period of ca. 4 months. During that period of time, a number of differences between the treatments emerged. Relative to the "low sulfate" mats, "normal sulfate" mats had: 1) lower consumption of oxygen in the lower levels of the mat, 2) higher efficiencies of oxygenic photosynthesis, and 3) higher rates of nitrogen fixation. Rates of methane production by the mats increased greatly as sulfate concentrations fell below ca. 0.2 mM. In contrast, "low" and "normal" sulfate mats had similar net rates of exchange of O2 and dissolved inorganic C between the mats and overlying water. Reduced sulfate levels have diverse impacts upon these ecosystems.

Bebout, Brad↗

NASA NTRS2010

Methanol Droplet Extinction in Carbon-Dioxide-Enriched Environments in Microgravity

Diffusive extinction of methanol droplets with initial diameters between 1.25 mm and 1.72 mm, burning in a quiescent microgravity environment at one atmosphere pressure, was obtained experimentally for varying levels of ambient carbon-dioxide concentrations with a fixed oxygen concentration of 21% and a balance of nitrogen. These experiments serve as precursors to those which are beginning to be performed on the International Space Station and are motivated by the need to understand the effectiveness of carbon-dioxide as a fire suppressant in low-gravity environments. In these experiments, the flame standoff distance, droplet diameter, and flame radiation are measured as functions of time. The results show that the droplet extinction diameter depends on both the initial droplet diameter and the ambient concentration of carbon dioxide. Increasing the initial droplet diameter leads to an increased extinction diameter, while increasing the carbon-dioxide concentration leads to a slight decrease in the extinction diameter. These results are interpreted using a critical Damk hler number for extinction as predicted by an earlier theory, which is extended here to be applicable in the presence of effects of heat conduction along the droplet support fibers and of the volume occupied by the support beads

Hicks, Michael C.↗

NASA NTRS1993

Property changes induced by the space environment in composite materials on LDEF: Solar array materials passive LDEF experiment A0171 (SAMPLE)

Surface modifications to composite materials induced by long term exposure in low earth orbit (LEO) were dominated by atomic oxygen erosion and micrometeoroid and space debris impacts. As expected, calculated erosion rates were peculiar to material type and within the predicted order of magnitude. Generally, about one ply of the carbon fiber composites was eroded during the 70 month LDEF experiment. Matrix erosion was greater than fiber erosion and was more evident for a polysulfone matrix than for epoxy matrices. Micrometeoroid and space debris impacts resulted in small (less than 1mm) craters and splattered contaminants on all samples. Surfaces became more diffuse and darker with small increases in emissivity and absorption. Tensile strength decreased roughly with thickness loss, and epoxy matrices apparently became slightly embrittled, probably as a result of continued curing under UV and/or electron bombardment. However, changes in the ultimate yield stress of the carbon reinforced epoxy composites correlate neither with weave direction nor fiber type. Unexpected developments were the discovery of new synergistic effects of the space environment in the interaction of atomic oxygen and copious amounts of contamination and in the induced luminescence of many materials.

Source record↗

NASA NTRS1987

Vertical constituent transport in the mesosphere

Ground-based microwave spectroscopy measurements of mesospheric CO and H2O vertical mixing ratio profiles are used to infer vertical mixing rates in the upper mesosphere. The CO and H2O data consistently imply vertical eddy diffusion coefficients in the 70- to 85-km region of 100,000-200,000 sq cm/s during spring through summer at midlatidues. Although chemical acceleration of vertical transport is substantial for O and O3, below the mesopause, the divergences of their associated fluxes are modest, with at most a factor of 2 effect on the concentrations of O and O3 for measured variability in gravity wave activity. Comparison of Solar Mesosphere Explorer (SME) O3 data with model results reinforces the conclusions of slow vertical mixing in the upper mesosphere as a consequence of the reduced HO(x) catalytic loss of odd oxygen. The changes in chemical rate constants recommended by Rusch and Eckman (1985), in conjunction with slow vertical mixing, yield good agreement with SME O3 data. The slow vertical mixing deduced in this study is consistent with upper limits obtained from studies of the mesospheric heat budget and could be construed as evidence for an advectively controlled mesosphere. A comparison of the vertical eddy diffusion coefficients for momentum stresses, constituent transport, and heat transport suggests that the eddy Prandtl number must be of order 10.

Strobel, Darrell F.↗