Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oxide solid electrolyte”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Materials design of sodium chloride solid electrolytes Na3MCl6 for all-solid-state sodium-ion batteries

All-solid-state sodium-ion batteries have attracted increasing attention owing to the low cost of sodium and the enhanced safety compared to conventional Li-ion batteries. Recently, halides have been considered as promising solid electrolytes (SEs) due to their favorable combination of high ionic conductivity and chemical stability against high-voltage cathode materials. Although a wide variety of lithium chloride SEs, Li 3 MCl 6 , have been developed for high-voltage all-solid-state batteries, only a limited number of sodium chloride SEs have been reported. This study aims to offer a material design insight for the development of sodium chloride SEs through systematic assessment of the phase stability, electrochemical stability, and transport properties of novel Na 3 MCl 6 SEs. Structural calculations indicate that Na 3 MCl 6 exhibits trigonal $P\bar{3}$1c, monoclinic P2 1 /n, and trigonal $R\bar{3}$ phases, and the stable phase of Na 3 MCl 6 is dependent on the type and ionic radius of M. Na 3 MCl 6 typically exhibits a high oxidation potential, demonstrating good electrochemical stability against cathodes. The bond-valence site energy and ab initio molecular dynamics calculations revealed that Na 3 MCl 6 with P2 1 /n and $R\bar{3}$ phases showed low ionic conductivity, while the $P\bar{3}$1c phase slightly improved the ionic conductivity of Na 3 MCl 6 . The formation of Na vacancies by aliovalent substitution considerably increased the ionic conductivity up to four orders of magnitude for pristine Na 3 MCl 6 , exhibiting ~10 –5 S cm –1 for trigonal $P\bar{3}$1c and $R\bar{3}$ phases. The formation of defects could further enhance the ionic conductivity of Na 3 MCl 6 , and the optimization of defect type and ratio can be helpful in developing superionic Na chloride SEs. The material design of Na 3 MCl 6 in this study will provide fundamental guidelines for the development of novel sodium halide SEs for all-solid-state sodium-ion batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Micro-Tubular Solid Oxide Fuel Cell Polarization and Impedance Variation With Thin Porous Samarium-Doped Ceria and Gadolinium-Doped Ceria Buffer Layer Thickness

Abstract Porous buffer layers for anode-supported solid oxide fuel cells (SOFCs) have been investigated for many years with different thicknesses of the buffer layer in each study. In this work, micro-tubular SOFCs having samarium-doped ceria (SDC) and gadolinium-doped ceria (GDC) buffer layers are compared using the current–voltage technique, electrochemical impedance spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The thickness of the porous SDC and GDC buffer layer is investigated systematically with the thickness varying between 0.3 and 2.0 μm. The power density varies between 212 and 1004 mW/cm2 for samples having different SDC buffer layer thickness. Comparable changes occur for the SOFCs with a GDC buffer layer, but less variation in polarization losses resulted. Variation in electrochemical performance varies due to changes in ohmic resistance, cathode activation polarization, and interfacial reactions between the cathode and electrolyte materials.

Electrochemistry↗
DOE OSTI2024

Development of Stable Solid Oxide Electrolysis Cells for Low-Cost Hydrogen Production

The project objective was to demonstrate a solid oxide cell-based steam electrolysis stack that exhibits robustness, reliability, endurance, hydrogen purity, and produces hydrogen at elevated pressure of 2 to 3 bar. Innovative materials and processing methods were evaluated to improve degradation characteristics. Performance improvement focused on nearly all layers involved in the cell and stack assembly. Primary attention was paid to zirconia-ceria interface resistance control via sintering optimization and decrease in degradation from the oxygen electrode by evaluating low strontium (Sr) or Sr-free composition for both the oxygen electrode and current collection layer. Stack robustness was addressed by validating redox tolerance of fuel electrode, confirming capability of cells to survive repeated thermal cycles, studying the effect of pressure on performance and degradation, evaluating the effect of contamination on fuel and oxygen electrode performance and degradation, and identifying mitigation strategies to improve performance. The characterization included evaluation of electrochemical performance and stability followed by microstructural analysis. At the cell level, performance and stability improvements were achieved by incorporating a Sr-free oxygen electrode and a denser oxygen electrode barrier layer. At the stack level, pressurized operation reduces demand on first stage compression, the redox tolerant fuel electrode mitigates risk from service interruptions, and improvements to interconnect coating alleviate chromium (Cr) contamination effects. The denser barrier layer was achieved by adding a sintering aid to the samaria-doped ceria (SDC) composition that reduced sintering temperature by 150 °C. The resulting density was on par with the baseline SDC barrier layer density and the lower sintering temperature resulted in less resistive phase formation during sintering. Button cell tests did not demonstrate a change in performance when exposed to silicon (Si) or manganese (Mn) impurities to the fuel electrode and Cr impurity to the oxygen electrode. More detailed study however is warranted. The project addressed SOEC performance and stability at the cell and stack levels through a systematic approach to known sources of degradation that were combined and tested in three stack tests using an electrolyte supported cell design to allow for evaluation of a variety of fuel and oxygen electrode compositions. STK-82 and STK-83 had identical compositions. STK-100 incorporated the best materials and processing variables developed under this and concurrent projects, and was tested at elevated pressure in steam electrolysis. • STK-82 recovered performance after redox and thermal cycling, demonstrating the robustness of the stack and seals. It exhibited stable performance in testing for 500 hours in SOEC mode, followed by 300 hours of cycling between SOEC and SOFC tests. Degradation during SOEC operation was 1.8 %/ 1,000 hours. • STK-83 generated hydrogen at >80% steam conversion, and oxygen above 98.5 % purity during pressurized operation. Both hydrogen and oxygen were generated at 3 barg pressure without the use of a pressure vessel. In addition to balanced pressure, electrolysis operation at 1 bar differential pressure across anode and cathode was also demonstrated to substantial the robustness of the cell and seal. • STK-100 measured at initial ambient pressure conditions showed an area specific resistance of 1.1 ohm-cm 2 , and STK-83 had 1.3 ohm-cm 2 .

08 HYDROGEN↗
DOE OSTI2020

Exploring Electrocatalysis of Methane on Transition Metal Surfaces

Methane is a potent greenhouse gas because it has a heat-absorbing ability that is 20 times stronger than the better-known carbon dioxide. It is also the dominant component of nature gas (>70%). Its current greenhouse effect is only second to carbon dioxide largely because of its relatively low atmospheric concentration. Alarmingly, however, the latter has seen a 1.5-time increase since 1750, mainly due to anthropogenic livestock farming, coal and natural gas mining, and organic matter decomposing in waste landfills. Mitigating such a trend effectively and efficiently is therefore highly desirable and intensely sought for. This final technical report describes some exciting research progresses made over the last three years supported financially by the aforementioned award. The research conducted focused on exploring electrochemical direct methane to methanol (DMTM) conversion under mild conditions. The goal of research was to explore the possibility of developing potentially game-changing electrocatalysts and electrocatalysis that can convert methane directly to methanol in a most sustainable way for curbing its effect on global warming. Progress has been made in the following three directions. First, by adapting a hydrogen fuel-cell configuration that enables gaseous methane to be transported directly to the electrocatalyst surface, we have overcome the perennial difficulty in measuring activity of methane electro-oxidation at low temperature and ambient pressure that has prevented any meaningful studies of electrocatalysis of methane conversion thus far. Second, we have developed a novel and operational in situ electrochemical infrared (IR) spectral cell for studying electrocatalysis of direct methane to methanol conversion. This novel cell is also expected to alleviate the measuring difficulty caused by low solubility of methane in aqueous electrolyte and low sticking coefficient for methane adsorption onto transition metal surface. It will improve significantly the IR’s signal to noise ratio. Third, we have successfully synthesized nano-sizing copper (Cu) exchanged zeolite mordenite (Cu-ZMOR) and coated it with carbon that enabled electrochemical access to the encaged Cu ions. This opens a door to unravel the chemistry of Cu ions in catalyzing direct methane to methanol conversion under mild experimental conditions. Altogether, these progresses achieved have laid a solid foundation for further exploring electrocatalysis of direct methane to methanol conversion in general where there exists “a plenty of room” for new discoveries and developments.

03 NATURAL GAS↗
DOE OSTI2025

Enabling Solar Water Oxidation by BiVO 4 in Strongly Acidic Solutions

The oxygen evolution reaction (OER) is paired with various electrochemical and photoelectrochemical reduction reactions used for fuel and chemical production. As there is a strong interest in performing many of these reduction reactions in strongly acidic solutions to increase the reaction rate, efficiency, or selectivity, there is also a great interest in enabling efficient and stable OER in strongly acidic solutions. In this study, we report stable photoelectrochemical OER (POER) of a BiVO 4 photoanode in 0.1 M HNO 3 (pH 1). This was achieved by using Nb 2 O 5 as a protection layer. While Nb 2 O 5 was rarely used as a protection layer for photoelectrodes in the past, we show its excellent capability to suppress both the chemical and photoelectrochemical dissolution of BiVO 4 at pH 1. After stabilizing BiVO 4 with a Nb 2 O 5 protection layer, we added Co 2+ ions to the electrolyte as an OER catalyst to enhance the POER. We found that Co (aq) 2+ can serve as a homogeneous OER catalyst without being deposited as a CoO x solid catalyst on Nb 2 O 5 . When we performed the POER using unprotected BiVO 4 with Co (aq) 2+ under the same condition, although POER was enhanced, the enhancement could not be sustained due to the chemical dissolution of BiVO 4 . After the POER, we found that a Co 3+ -containing OER catalyst was deposited on the bare BiVO 4 surface. This result suggested that the use of Co 2+ ions as a homogeneous catalyst was possible due to the inertness of the Nb 2 O 5 surface toward the adsorption or deposition of Co ions. This study enabling stable POER of BiVO 4 in 0.1 M HNO 3 using the combination of a Nb 2 O 5 protection layer and Co (aq) 2+ as a homogeneous OER catalyst provides promising possibilities for acidic POER and OER.

Catalysts↗
DOE OSTI2025

Fast lithium ion diffusion in brownmillerite Li x Sr 2 Co 2 O 5

Transition metal oxides not only exhibits novel magnetic properties but also provides outstanding ionic transports. Ionic conductors have great potential for interesting tunable physical properties via ionic liquid gating and novel energy storage applications such as all-solid-state lithium batteries. In particular, low migration barriers and high hopping attempt frequency are the keys to achieve fast ion diffusion in solids. Taking advantage of the oxygen-vacancy channel in Li x Sr 2 Co 2 O 5 , we show that migration barriers of lithium ion are as small as 0.28–0.17 eV depending on the lithium concentration rates. Our first-principles calculation also investigated hopping attempt frequency and concluded the room temperature ionic diffusivity and ion conductivity are high as 10 −7 –10 −6 cm 2 s −1 and 10 −3 –10 −2 Scm −1 , respectively, which outperform most of perovskite-type, garnet-type, and sulfide Li-ion solid-state electrolytes. This work proves Li x Sr 2 Co 2 O 5 as a promising super-ionic conductor.

Crystallographic defects↗
DOE OSTI2023

Improved cell performance and sulphur tolerance using A-site substituted Sr2Fe1.4Ni0.1Mo0.5O6–δ anodes for solid-oxide fuel cells

Abstract Solid-oxide fuel cells (SOFCs) offer great promise for producing electricity using a wide variety of fuels such as natural gas, coal gas and gasified carbonaceous solids; however, conventional nickel-based anodes face great challenges due to contaminants in readily available fuels, especially sulphur-containing compounds. Thus, the development of new anode materials that can suppress sulphur poisoning is crucial to the realization of fuel-flexible and cost-effective SOFCs. In this work, La0.1Sr1.9Fe1.4Ni0.1Mo0.5O6–δ (LSFNM) and Pr0.1Sr1.9Fe1.4Ni0.1Mo0.5O6–δ (PSFNM) materials have been synthesized using a sol-gel method in air and investigated as anode materials for SOFCs. Metallic nanoparticle-decorated ceramic anodes were obtained by the reduction of LSFNM and PSFNM in H2 at 850°C, forming a Ruddlesden–Popper oxide with exsolved FeNi3 bimetallic nanoparticles. The electrochemical performance of the Sr2Fe1.4Ni0.1Mo0.5O6–δ ceramic anode was greatly enhanced by La doping of A-sites, resulting in a 44% decrease in the polarization resistance in reducing atmosphere. The maximum power densities of Sr- and Mg-doped LaGaO3 (LSGM) (300 μm) electrolyte-supported single cells with LSFNM as the anode reached 1.371 W cm −2 in H2 and 1.306 W cm–2 in 50 ppm H2S–H2 at 850°C. Meanwhile, PSFNM showed improved sulphur tolerance, which could be fully recovered after six cycles from H2 to 50 ppm H2S–H2 operation. This study indicates that LSFNM and PSFNM are promising high-performance anodes for SOFCs.

Li, Haixia↗
DOE OSTI2026

A Dendrite-Resistant Sodium/Porous-Carbon Anode for Solid-State Batteries – Strategies and Challenges for Low-Pressure Operation

Sodium solid-state batteries (Na-SSB) have gained interest recently due to the abundance of Na over Li, but they still tend to fail due to dendrites under practical current densities and cycling capacities. To overcome this, Na-SSBs are frequently tested with impractically high applied pressure. In this work, a porous carbon interfacial layer is utilized in conjunction with Na-ß”-Al2O3 solid electrolytes to enable Na-cycling at milder cell pressures. This sodium/porous carbon layer enables improved solid-state Na cycling in symmetric cells, up to a current density of 10 mA cm-2 at 25 °C. Cycling up to 1 mAh cm-2 is challenging with low pressure, but 1 mAh cm-2 capacity can be reliably cycled at 1 mA cm-2 at an elevated temperature of 60 °C in symmetric cells. Finally, the evolution of the interface and sodium/carbon anode is evaluated with cryogenic ion-milling and cross-sectional imaging revealing that, depending on testing temperature, pressure, current density, and capacity, void formation, Na-extraction from porous carbon, delamination of the porous carbon matrix, or a combination of these occurs at the interface between Na-metal and BASE. Despite this, excellent dendrite resistance is achieved, and a full-cell design utilizing a Na-transition metal oxide cathode is still able to achieve an areal capacity of ~ 2.7 mAh cm-2 at 0.125 mA cm-2. This work demonstrates an alternative pathway toward a Na-metal anode for Na-SSBs without the requirement of excessive stack pressure.

low-cost↗
DOE OSTI2024

Theoretical Understanding of Effects of Operating Modes on the Performance Durability of Solid Oxide Cells: A Comparison between Potentiostatic and Galvanostatic Operations

In solid oxide cells (SOCs), the choice between galvanostatic (constant current) and potentiostatic (constant voltage) modes does not significantly affect the performance of SOCs as long as the cell components remain unchanged and intact. However, the degradation of cell components, which leads to changes in electrochemical and physical properties of the cell, elevates the importance of the selected operating mode. This paper aims to investigate the effects of galvanostatic and potentiostatic operating modes on the evolving properties of SOCs and their subsequent influence on performance durability. Employing non-equilibrium thermodynamic analysis, a crucial approach for understanding the degradation phenomena within an active electrochemical system, this study aims to provide in-depth insights into how these operating modes affect the longevity and efficacy of SOCs. Key findings include: In cases where oxygen electrode (OE) degradation is accelerated by higher partial pressure of oxygen ( p O 2 ), operating under constant voltage electrolysis can mitigate the high p O 2 at the OE|electrolyte (OE|EL) interface. Conversely, if OE degradation occurs more rapidly under a lower p O 2 , constant current electrolysis is more effective in suppressing degradation by achieving a high p O 2 at the OE|EL interface. For degradation of the fuel electrode (FE) due to higher p O 2 , constant current electrolysis is beneficial for more stable performance, which helps maintain low p O 2 at the FE|EL interface. When FE degradation is accelerated by lower p O 2 , constant voltage electrolysis can avert low p O 2 at the FE|EL interface. In practical scenarios, more complex degradation mechanisms come into play, especially when p O 2 significantly deviates from initial conditions. Degradation in one electrode can influence p O 2 in the other electrode, a phenomenon more pronounced in potentiostatic than in galvanostatic electrolysis.

Electrochemistry↗
DOE OSTI2022

Durable, High-Performance Unitized Reversible Fuel Cells Based on Proton Conductors

The main objective of this project was to develop robust, highly efficient, and economically viable H + -conducting membrane-based, unitized reversible fuel cell (H-URFC) technology for large-scale co-located energy storage and power generation. Another objective of this project is to gain a profound understanding of the degradation mechanisms of key stack materials and interfaces using various in situ, ex situ, and operando measurements guided by theoretical analysis. Nanostructured components will be integrated into cell design and the interfaces between electrodes and electrolyte will be modified with active bi-functional catalysts and protective coatings in order to achieve >70% roundtrip efficiency at 1 A/cm2 in both the fuel cell and the electrolysis modes. The end goal of the project is to advance the technology to the point that a university-industry collaboration can be established to scale up the technology for early adoption, and eventually enabling a pathway to large-scale energy storage that utilizes chemical storage and conversion for electrical grid balancing.

08 HYDROGEN↗
DOE OSTI2024

Hydrogen in energy and information sciences

Beyond its fascinating chemistry as the first element in the Periodic Table, hydrogen is of high societal importance in energy technologies and of growing importance in energy-efficient computing. In energy, hydrogen has reemerged as a potential solution to long-term energy storage and as a carbon-free input for materials manufacturing. Its utilization and production rely on the availability of proton-conducting electrolytes and mixed proton–electron conductors for the components in fuel cells and electrolyzers. In computing, proton mediation of electronic properties has garnered attention for electrochemically controlled energy-efficient neuromorphic computing. Incorporation of substitutional and interstitial hydride ions in oxides, though only recently established, enables tuning of electronic and magnetic properties, inviting a range of possible exotic applications. This article addresses common themes in the fundamental science of hydrogen incorporation and transport in oxides as relevant to pressing technological needs. The content covers (1) lattice (or bulk) mechanisms of hydrogen transport, primarily addressing proton transport, but also touching on hydride ion transport; (2) interfacial transport; (3) exploitation of extreme external drivers to achieve unusual response; and (4) advances in methods to probe the hydrogen environment and transport pathway. The snapshot of research activities in the field of hydrogen-laden materials described here underscores exciting recent breakthroughs, remaining open questions, and breathtaking experimental tools now available for unveiling the nature of hydrogen in solid-state matter.

08 HYDROGEN↗
DOE OSTI2019

Dendrite–Free Potassium Metal Anodes in a Carbonate Electrolyte

Potassium (K) metal anodes suffer from a challenging problem of dendrite growth. In this study, it is demonstrated that a tailored current collector will stabilize the metal plating–stripping behavior even with a conventional KPF 6 –carbonate electrolyte. A 3D copper current collector is functionalized with partially reduced graphene oxide to create a potassiophilic surface, the electrode being denoted as rGO@3D–Cu. Potassiophilic versus potassiophobic experiments demonstrate that molten K fully wets rGO@3D–Cu after 6 s, but does not wet unfunctionalized 3D–Cu. Electrochemically, a unique synergy is achieved that is driven by interfacial tension and geometry: the adherent rGO underlayer promotes 2D layer–by–layer (Frank–van der Merwe) metal film growth at early stages of plating, while the tortuous 3D–Cu electrode reduces the current density and geometrically frustrates dendrites. The rGO@3D–Cu symmetric cells and half–cells achieve state–of–the–art plating and stripping performance. Here, the symmetric rGO@3D–Cu cells exhibit stable cycling at 0.1–2 mA cm –2 , while baseline Cu prematurely fails when the current reaches 0.5 mA cm –2 . The half–cells cells of rGO@3D–Cu (no K reservoir) are stable at 0.5 mA cm –2 for 10 000 min (100 cycles), and at 1 mA cm –2 for 5000 min. The baseline 3D–Cu, planar rGO@Cu, and planar Cu foil fails after 5110, 3012, and 1410 min, respectively.

25 ENERGY STORAGE↗
DOE OSTI2024

Electro-Chemo-Mechanical Evolution at the Garnet Solid Electrolyte–Cathode Interface

Solid-state batteries promise higher energy density and improved safety compared with lithium-ion batteries. However, electro-chemomechanical instabilities at the solid electrolyte interface with the cathode and the anode hinder their large scale implementation. Here, in this study, we focus on resolving electro-chemo-mechanical instability mechanisms and their onset conditions between a state-of-the-art cathode, LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622), and the garnet Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolyte. We used thin-film NMC622 on LLZO pellets to place the interfacial region within the detection depth of the X-ray characterization techniques. The experimental probes of the near-interface region included in operando X-ray absorption spectroscopy and ex situ focused ion beam scanning electron microscopy. Electrochemical degradation was not observable during cycling at room temperature with 4.3 V versus Li/Li + charge voltage cutoff, or with stepwise potentiostatic hold up to 4.1 V versus Li/Li + . In contrast, secondary phases including reduced transition metal species (Ni 2+ , Co 2+ ) were found after cycling up to 4.3 V versus Li/Li + at 80 °C and during potentiostatic hold at 4.3 V versus Li/Li + (Ni 2+ ). Intergranular cracks between NMC622 grains and delamination at the NMC622|LLZO interface occurred readily after the first charge. These interface reaction products and mechanical failure lowered the capacity and cell efficiency due to partial loss of the NMC622 phase, partial loss of contact at the interface, and a higher polarization resistance. Electrochemical instability between delithiated NMC622 and LLZO could be mitigated by using a low charge voltage cutoff or cycling at lower temperature. Ways to engineer the mechanical properties to avoid crack deflection and delamination at the interface are also discussed for enhancing mechanical stability.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Stable perovskite-fluorite dual-phase composites synthesized by one-pot solid-state reactive sintering for protonic ceramic fuel cells

We report that this work synthesized a series of oxide composites with nominal compositions of BaCe 05 Zr 0.4 Y 0.1 O 3-δ (BCZY)-Ce 0.5 Y 0.5 O 2-δ (YDC) based on the BCZY/YDC molar ratios of 0.5:1, 1:1, 2:1, and 4:1 (BCZY-YDC-0.5–1, BCZY-YDC-1-1, BCZY-YDC-2-1, and BCZY-YDC-4-1) using a one-pot solid state reactive sintering (SSRS) method. The X-ray diffraction (XRD) patterns and refinement proved that the one-pot SSRS at 1450 °C for 12 h could achieve the perovskite-fluorite dual-phase composites (DPCs) with the desired structure compositions. The scanning electron microscopy (SEM) images showed that the two DPCs of BCZY-YDC-1-1 and BCZY-YDC-2-1 formed excellent percolation for perovskite and fluorite phases. The conductivity measurement by electrochemical impedance spectroscopy (EIS) and the transference number measurement by the electromotive force (EMF) test proved that changing the BCZY/YDC molar ratio and operating condition could adjust the DPC's conduction property to make them suitable for electrolytes and electrode scaffolds for protonic ceramic fuel cells (PCFCs). The long-term conductivity testing and the crystal structure analysis after EMF testing under versatile conditions indicated that the DPCs of BCZY-YDC-2-1 and BCZY-YDC-1-1 were durable PCFC component materials. The PCFC button cells with the as-discovered BCZY-YDC-2-1 and BCZY-YDC-1-1 as an electrolyte and an anode scaffold, respectively, and the reported Ba–Ce–Fe–Co–O perovskite-perovskite composite as a cathode showed promising performance under H 2 /air gradient.

08 HYDROGEN↗
DOE OSTI2020

Realizing Complete Solid-Solution Reaction in High Sodium Content P2-Type Cathode for High-Performance Sodium-Ion Batteries

P2-type layered oxides suffer from an ordered Na + /vacancy arrangement and P2→O2/OP4 phase transitions, leading them to exhibit multiple voltage plateaus upon Na + extraction/insertion. The deficient sodium in the P2-type cathode easily induces the bad structural stability at deep desodiation states and limited reversible capacity during Na + de/insertion. These drawbacks cause poor rate capability and fast capacity decay in most P2-type layered oxides. In this work, to address these challenges, a novel high sodium content (0.85) and plateau-free P2-type cathode-Na 0.85 Li 0.12 Ni 0.22 Mn 0.66 O 2 (P2-NLNMO) was developed. The complete solid-solution reaction over a wide voltage range ensures both fast Na + mobility (10 -11 to 10 -10 cm 2 s -1 ) and small volume variation (1.7%). Furthermore, the high sodium content P2-NLNMO exhibits a higher reversible capacity of 123.4 mAhg -1 , superior rate capability of 79.3 mAhg -1 at 20 C, and 85.4% capacity retention after 500 cycles at 5 C. The sufficient Na and complete solid-solution reaction are critical to realizing high-performance P2-type cathodes for sodium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Effect of Water Concentration in LiPF 6 -Based Electrolytes on the Formation, Evolution, and Properties of the Solid Electrolyte Interphase on Si Anodes

A trace amount of water in an electrolyte is one of the factors detrimental to the electrochemical performance of silicon (Si)-based lithium-ion batteries that adversely affect the formation and evolution of the solid electrolyte interphase (SEI) on Si-based anodes and change its properties. Thus far, a lack of fundamental and mechanistic understanding of SEI formation, evolution, and properties in the presence of water has inhibited efforts to stabilize the SEI for improved electrochemical performance. As such, we investigated the SEI formed in a Gen2 electrolyte (1.2 M LiPF6 in ethylene carbonate/ethyl methyl carbonate, 3:7 wt %, water content: <10 ppm) with and without additional water (50 ppm) at varying potentials (1.0, 0.5, 0.2, and 0.01 V vs Li/Li + ). The impact of additional water on the morphological, (electro)chemical, and structural properties of SEI was studied using microscopic (atomic force microscopy and scanning spreading resistance microscopy) and spectroscopic (X-ray photoelectron spectroscopy, attenuated total reflection Fourier-transform infrared spectroscopy, and time-of-flight secondary ion mass spectrometry) techniques. The SEI exhibits both potential- and water concentration-dependent trends in its morphology and chemical composition. The presence of additional water in the electrolyte causes parasitic reactions, which onset at ~1.0 V, resulting in a reduction of electrolyte components and result in the formation of an insulating, fluorophosphate-rich SEI. In addition, hydrolysis of LiPF 6 creates hydrofluoric acid, which reacts with the surface oxide layer on the Si electrode, leading to a pitted and inhomogeneous SEI structure.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Precipitation of dopants on acceptor-doped LaMnO3±δ revealed by defect chemistry from first principles

Perovskite oxides degrade at elevated temperatures while precipitating dopant-rich particles on the surface. A knowledge-based improvement of surface stability requires a fundamental and quantitative understanding of the dopant precipitation mechanism on these materials. We propose that dopant precipitation is a consequence of the variation of dopant solubility between calcination and operating conditions in solid oxide fuel cells (SOFCs) and electrolyzer cells (SOECs). To study dopant precipitation, we use 20% (D = Ca, Sr, Ba)-doped LaMnO3+δ (LDM20) as a model system. We employ a defect model taking input from density functional theory calculations. The defect model considers the equilibration of LDM20 with a reservoir consisting of dopant oxide (DO), peroxide (DO2), and O2 in the gas phase. The equilibrated non-stoichiometry of the A-site and B-site as a function of temperature, T, and oxygen partial pressure, p(O2), reveals three regimes for LDM20: A-site deficient (oxidizing conditions), A-site rich (atmospheric conditions), and near-stoichiometric (reducing conditions). Assuming an initial A/B non-stoichiometry, we compute the dopant precipitation boundaries in a p–T phase diagram. Our model predicts precipitation both under reducing (DO) and under highly oxidizing conditions (DO2). We found precipitation under anodic, SOEC conditions to be promoted by large dopant size, while under cathodic, SOFC conditions precipitation is promoted by initial A-site excess. The main driving forces for precipitation are oxygen uptake by the condensed phase under oxidizing conditions and oxygen release assisted by B-site vacancies under reducing conditions. Possible strategies for mitigating dopant precipitation under in electrolytic and fuel cell conditions are discussed.

Hess, Franziska (ORCID:000000024460643X)↗
DOE OSTI2020

Continuum Description of the Role of Negative Transference Numbers on Ion Motion in Polymer Electrolytes

New experimental techniques such as electrophoretic NMR (eNMR) are emerging as powerful methods for directly measuring ion velocities in electrolytes under applied electric fields. The aim of this theoretical study is to predict the spatial- and temporal-dependence of these velocities of ions as a function of the magnitude of the applied field and salt concentration. It has recently been shown that mixtures of poly(ethylene oxide)-based (PEO) and lithium bis(trifluoromethanesulfonyl) imide (LiTFSI) electrolytes exhibit negative cation transference numbers in a certain salt concentration range. In this range, the cation motion at early times is directed to the positive electrode at all locations in the cell; ion migration dominates in this regime. As time progresses, the cation velocity in finite zones near both the electrodes changes sign. These zones grow rapidly with time, reflecting the increasing importance of diffusion, and a point in time is reached beyond which the cation velocity in the entire cell is directed toward the negative electrode. Overall, our work reveals the limited time window over which the results of eNMR can be used to determine the transference number. More importantly, it shows how to account for the effect of diffusional flux in such experiments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗