Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “observable behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Accelerated fatigue crack growth behavior of PWA 1480

An investigation of the fatigue crack growth (FCG) behavior of PWA 1480 single crystal nickel base superalloy was conducted. Typical Paris region behavior was observed above a delta K of 8 MPa sq rt of m. However, below that stress intensity range, the alloy exhibited highly unusual behavior. This behavior consisted of a region where the crack growth rate became essentially independent of the applied stress intensity. The transition in the FCG behavior was related to a change in the observed crack growth mechanisms. In the Paris region, fatigue failure occurred along (111) facets; however, at the lower stress intensities, (001) fatigue failure was observed. A mechanism was proposed, based on barriers to dislocation motion, to explain the changes in the observed FCG behavior. The FCG data were also evaluated in terms of a recently proposed stress intensity parameter, K sub rss. This parameter, based on the resolved shear stresses on the slip planes, quantified the crack driving force as well as the mode I delta K, and at the same time was also able to predict the microscopic crack path under different stress states.

Telesman, Jack↗
DOE OSTI2023

Anomalous electronic transport in high-mobility Corbino rings

We report low-temperature electronic transport measurements performed in two multi-terminal Corbino samples formed in GaAs/Al-GaAs two-dimensional electron gases (2DEG) with both ultra-high electron mobility ( ≳ 20 × 10 6 cm 2 / Vs) and with distinct electron density of 1.7 and 3.6 × 10 11 cm -2 . In both Corbino samples, a non-monotonic behavior is observed in the temperature dependence of the resistance below 1 K. Surprisingly, a sharp decrease in resistance is observed with increasing temperature in the sample with lower electron density, whereas an opposite behavior is observed in the sample with higher density. To investigate further, transport measurements were performed in large van der Pauw samples having identical heterostructures, and as expected they exhibit resistivity that is monotonic with temperature. Finally, we discuss the results in terms of various lengthscales leading to ballistic and hydrodynamic electronic transport, as well as a possible Gurzhi effect.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS2003

Xenon Sputter Yield Measurements for Ion Thruster Materials

In this paper, we describe a technique that was used to measure total and differential sputter yields of materials important to high specific impulse ion thrusters. The heart of the technique is a quartz crystal monitor that is swept at constant radial distance from a small target region where a high current density xenon ion beam is aimed. Differential sputtering yields were generally measured over a full 180 deg arc in a plane that included the beam centerline and the normal vector to the target surface. Sputter yield results are presented for a xenon ion energy range from 0.5 to 10 keV and an angle of incidence range from 0 deg to 70 deg from the target surface normal direction for targets consisting of molybdenum, titanium, solid (Poco) graphite, and flexible graphite (grafoil). Total sputter yields are calculated using a simple integration procedure and comparisons are made to sputter yields obtained from the literature. In general, the agreement between the available data is good. As expected for heavy xenon ions, the differential and total sputter yields are found to be strong functions of angle of incidence. Significant under- and over-cosine behavior is observed at low- and high-ion energies, respectively. In addition, strong differences in differential yield behavior are observed between low-Z targets (C and Ti) and high-Z targets (Mo). Curve fits to the differential sputter yield data are provided. They should prove useful to analysts interested in predicting the erosion profiles of ion thruster components and determining where the erosion products re-deposit.

Williams, John D.↗
NASA NTRSDate not supplied

Ab-Initio Study of Stacking Fault Segregation Behavior in Ni-based Superalloys at High Temperatures

Ni-based superalloys demonstrate extraordinary creep properties compared to traditional metallic systems due to the formation of L12 (γ’) precipitates. Despite experimental evidence of alloying element segregation to the stacking faults, prior ab-initio efforts indicated repulsion of Nb from superlattice intrinsic stacking faults (SISFs) . Due to the importance of this element in key strengthening mechanisms, we developed a new technique to account for multi-component segregation behavior at temperature combining ab-initio molecular dynamics (AIMD) and Monte-Carlo (MC) simulations. Using this technique, we replicated experimentally observed segregation behavior of Nb, Co, and Ti to the SISF in L12 (Figure 1). Furthermore, we investigated the co-segregation behaviors of individual pairs of alloying elements to determine the interaction effects which lead to this segregation behavior in the full alloy system. By simulating the reduced-chemistry models using our approach, we reconciled previous ab-initio calculations demonstrating repulsion of Nb from the SISF and the experimentally observed segregation behavior.

Molecular Dynamics↗
NASA NTRS1982

Behavior of the Si/SiO2 interface observed by Fowler-Nordheim tunneling

Thin-oxide (40-50 A) metal oxide semiconductor (MOS) structures are shown to exhibit, before large levels of electron tunnel injection, the near-ideal behavior predicted for a uniform trapezoidal barrier with thick-oxide properties. The oscillatory field dependence caused by electron-wave interference at the Si/SiO2 interface suggests an abrupt, one-monolayer barrier transition (approximately 2.5 A) consistent with earlier work. After tunnel injection of 10 to the 17th - 5 x 10 to the 18th electrons/sq cm, the barrier undergoes appreciable degradation, leading to enhanced tunneling conductance. Reproducible behavior is observed among different samples. This effect is found to be consistent with the generation of positive states in the region of the oxide near the Si/SiO2 interface (less than 20 A), where the tunneling electrons emerge into the oxide conduction band.

Maserjian, J.↗
DOE OSTI2025

Spontaneously formed phonon frequency combs in van der Waals solid CrGeTe 3 and CrSiTe 3

Optical phonon engineering through nonlinear effects has been utilized in ultrafast control of material properties. However, nonlinear optical phonons typically exhibit rapid decay due to strong mode-mode couplings, limiting their effectiveness in temperature or frequency sensitive applications. Here we report the observation of long-lived nonlinear optical phonons through the spontaneous formation of phonon frequency combs in the van der Waals material CrXTe 3 (X=Ge, Si) using high-resolution Raman scattering. Unlike conventional optical phonons, the highest A g mode in CrGeTe 3 splits into equidistant, sharp peaks forming a frequency comb that persists for hundreds of oscillations and survives up to 200K. These modes correspond to localized oscillations of Ge 2 Te 6 clusters, isolated from Cr hexagons, behaving as independent quantum oscillators. Introducing a cubic nonlinear term to the harmonic oscillator model, we simulate the phonon time evolution and successfully replicate the observed comb structure. Similar frequency comb behavior is observed in CrSiTe 3 , demonstrating the generalizability of this phenomenon. Our findings demonstrate that Raman scattering effectively probes high-frequency nonlinear phonon modes, offering insight into the generation of long-lived, tunable phonon frequency combs with potential applications in ultrafast material control and phonon-based technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Neutrinoless Double-Beta Decay Investigations of 82Se Using Three Shell Model Hamiltonians

Neutrinoless double-beta decay is considered one of the most promising processes that would help clarify some of the symmetry-breaking problems in our understanding of the observable universe. Recent studies of neutrinoless double-beta decay matrix elements have employed statistical approaches based on modified shell model effective Hamiltonians for 48Ca (Phys. Rev. C 106, 054302 (2022)) and 136Xe (Phys. Rev. C 107, 045501 (2023)). The analyses rely on inducing perturbations in the starting effective Hamiltonians to observe the behavior of a wide range of observables, besides the 0νββ) NME, that are compared with experimental data. Following a Bayesian model averaging approach, the range of probable values for the neutrinoless double-beta decay matrix elements is presented. In this paper, we present a similar study for 82Se, which is described in the same model space as 76Ge that is under experimental observation. Due to its faster calculation time compared to 76Ge, 82Se can be used as an appropriate substitute in our complex statistical study. Using the calculations performed for the statistical analysis of the neutrinoless double-beta decay matrix elements, we also search for the correlations between the observables that we can compare to experimental data.

Science & Technology - Other Topics↗
NASA NTRS1974

Research study on materials processing in space experiment number M512

Conclusions of the team of specialists can be generalized as: (1) Brazing and welding of metal structures in an orbital near zero gravity condition are quite feasible. (2) Design of joints for fabrication in zero gravity will place less emphasis on the tolerances and proximity of the adjacent structures than on the quantity of liquid metal available. (3) Brazing of metallic joints has many advantages over electron beam welding for practical reasons: simplicity, launch weight, development costs, joint design tolerances, remotization, etc. (4) No evidence of different physical or mechanical properties of liquid metals in zero gravity was observed. However, many differences in liquid behavior were observed. Many of these effects have been called adhesion-cohesion phenomena.

Tobin, J. M.↗
NASA NTRS1976

Some observations on the oscillatory behavior of carbon monoxide oxidation

The oscillatory behavior of the oxidation of carbon monoxide was experimentally studied in an attempt to further elucidate the reaction at low pressure. The phenomenon is observed as multiple explosions and involves successive flashes of light accompanying the slow reaction in a static system, including over 450 flashes in one case. Electronically excited hydroxyl radicals (water impurity) and carbon dioxide have been identified as components of the emission. The phase difference between the two was seen to be negligible. The nature of the temperature and pressure changes during a cycle indicates that the oscillation is purely kinetic rather than thermokinetic. A procedure is presented whereby sustained oscillations can be obtained for particular regions in the pressure-temperature plane, vessel surface pretreatments, and H2O-containing reactants.

Mccaffrey, B. J.↗
NASA NTRS1979

Electrostatic discharge properties of selected Voyager spacecraft materials

Twelve material and component samples were exposed to an electron beam in order to measure the time history and amplitude of resultant electrostatic discharges. The typical experimental design was to mount the test article with its dielectric surface facing the beam and its conductive portion isolated from ground except by way of a shielded cable on which a discharged pulse could be observed. The behavior of the sample was then observed at bombarding energies from 20 to 100 keV in increasing 20 keV increments and then 90 to 30 keV in decreasing 20 keV increments. Observations were made at each energy for nominally two hours at an electron flux of 4 x 10 to the 9th power/sq cm/sec.

Barengoltz, J. B.↗
NASA NTRS1987

Diagnostic reasoning in digital systems

Described is an efficient method for fault diagnosis in digital systems based on the technique of reasoning. The methodology operates on the observed erroneous behavior and the structure of the system. The behavior consists of the error(s) observed on the circuit's output lines and specific values on the circuit's input lines. The techniques described improve on previously published research on diagnostic reasoning in two ways. Previous work has stressed system independent techniques which could be used to diagnose any faulty system whose structure can be represented. By concentrating on the specific case of diagnosing faulty digital circuits, it is possible to simplify the representation of the structure of the system. This representation, in the form of an AND/OR fault tree, efficiently abstracts the structure of a faulty digital system. More importantly, a method for partitioning the digital system is introduced which can considerably reduce the runtime complexity of a diagnosis.

Thearling, Kurt Henry↗
NASA NTRS1989

Neutron stars: A cosmic hadron physics laboratory

A progress report is given on neutron stars as a cosmic hadron physics laboratory. Particular attention is paid to the crustal neutron superfluid, and to the information concerning its properties which may be deduced from observations of pulsar glitches and postglitch behavior. Current observational evidence concerning the softness or stiffness of the high density neutron matter equation of state is reviewed briefly, and the (revolutionary) implications of a confirmation of the existence of a 0.5 ms pulsar at the core of (Supernova) SN1987A are discussed.

Pines, David↗
NASA NTRS1989

Neutron stars - A cosmic hadron physics laboratory

A progress report is given on neutron stars as a cosmic hadron physics laboratory. Particular attention is paid to the crustal neutron superfluid, and to the information concerning its properties which may be deduced from observations of pulsar glitches and postglitch behavior. Current observational evidence concerning the softness or stiffness of the high density neutron matter equation of state is reviewed briefly, and the (revolutionary) implications of a confirmation of the existence of a 0.5 ms pulsar at the core of (Supernova) SN1987A are discussed.

Pines, David↗
NASA NTRS1992

Non-LTE, line-blanketed model atmospheres for late O- and early B-type stars

The use of non-LTE line-blanketed model atmospheres to analyze the spectra of hot stars is reported. The stars analyzed are members of clusters and associations, have spectral types in the range O9-B2 and luminosity classes in the range III-IV, have slow to moderate rotation, and are photometrically constant. Sampled line opacities of iron-group elements were incorporated in the radiative transfer solution; solar abundances were assumed. Good to excellent agreement is obtained between the computed profiles and essentially all the line profiles used to fix the model, and reliable stellar parameters are derived. The synthetic M II 5581 equivalent widths agree well with the observed ones at the low end of the temperature range studied, but, above 25,000 K, the synthetic line is generally stronger than the observed line. The behavior of the observed equivalent widths of N II, N III, C II and C III lines as a function of Teff is studied. Most of the lines show much scatter, with no consistent trend that could indicate abundance differences from star to star.

Grigsby, James A.↗
NASA NTRS2017

Behavioral Adaptations of Female Mice on the International Space Station

Adult female mice were sent to the International Space Station (ISS) as part of an early life science mission utilizing NASA's Rodent Habitat. Its primary purpose was to provide further insight into the influence of a microgravity environment on various aspects of mammalian physiology and well-being as part of an ongoing program of research aimed ultimately at understanding and ameliorating the deleterious influences of space on the human body. The present study took advantage of video collected from fixed, in-flight cameras within the habitat itself, to assess behavioral adaptations observed among in-flight mice aboard the ISS and differences in behavior with respect to a control group on the ground. Data collection consisted of several behavioral measures recorded by a trained observer with the assistance of interactive behavior analysis software. Specific behavioral measures included frequencies of conspecific interactionsociability, time spent feeding and conducting hygienic behavior, and relative durations of thigmotactic behavior, which is commonly used as an index of anxiety. Data were used to test tentative hypotheses that such behaviors differ significantly across mice under microgravity versus 1g conditions, and the assumption that the novel experience of microgravity itself may represent an initially anxiogenic stimulus which an animal will eventually acclimate to, perhaps through habituation.

Behavior in space↗
NASA NTRS2017

Behavioral Adaptations of Female Mice on the International Space Station

Adult female mice were sent to the International Space Station (ISS) as part of an early life science mission utilizing NASA's Rodent Habitat. Its primary purpose was to provide further insight into the influence of a microgravity environment on various aspects of mammalian physiology and well-being as part of an ongoing program of research aimed ultimately at understanding and ameliorating the deleterious influences of space on the human body. The present study took advantage of video collected from fixed, in-flight cameras within the habitat itself, to assess behavioral adaptations observed among in-flight mice aboard the ISS and differences in behavior with respect to a control group on the ground. Data collection consisted of several behavioral measures recorded by a trained observer with the assistance of interactive behavior analysis software. Specific behavioral measures included frequencies of conspecific interactionsociability, time spent feeding and conducting hygienic behavior, and relative durations of thigmotactic behavior, which is commonly used as an index of anxiety. Data were used to test tentative hypotheses that such behaviors differ significantly across mice under microgravity versus 1g conditions, and the assumption that the novel experience of microgravity itself may represent an initially anxiogenic stimulus which an animal will eventually acclimate to, perhaps through habituation.

rodent behavior↗
NASA NTRS2002

Surface Composition of NiPd Alloys

Surface segregation in Ni-Pd alloys has been studied using the BFS method for alloys. Not only does the method predict an oscillatory segregation profile but it also indicates that the number of Pd-enriched surface planes can vary as a function of orientation. The segregation profiles were computed as a function of temperature, crystal face, and composition. Pd enrichment of the first layer is observed in (111) and (100) surfaces, and enrichment of the top two layers occurs for (110) surfaces. In all cases, the segregation profile shows oscillations that are actually related to weak ordering tendencies in the bulk. An atom-by-atom analysis was performed to identify the competing mechanisms leading to the observed surface behaviors. Large-scale atomistic simulations were also performed to investigate the temperature dependence of the segregation profiles as well as for analysis of the bulk structures. Finally, the observed surface behaviors are discussed in relation to the bulk phase structure of Ni-Pd alloys, which exhibit a tendency to weakly order.

Noebe, Ronald D.↗
DOE OSTI2020

Crack Growth Rate and Fracture Toughness Tests on Irradiated Ex-Plant Materials

The performance of structural materials is critical for the safe and economic operation of light water reactors. Exposed to neutron irradiation during service, the reactor core internal materials can undergo significant microstructural and microchemical changes, leading to irradiation hardening and embrittlement. To ensure the structural integrity and functionality of nuclear reactor components during long-term operation, material degradation and damage mechanisms must be understood and managed adequately. In this work, irradiated materials harvested from the decommissioned Zorita reactor were studied for their cracking susceptibility and fracture resistance as a function of irradiation dose up to 47 displacement per atom (dpa). The material is a Type 304 stainless steel sectioned from the baffle plates of this pressurized water reactor with 38 years of service. Crack growth rate and fracture toughness J-resistance (J-R) curve tests were performed in low-corrosion-potential environments at ~315°C. All samples behaved similarly under cyclic loading, and no deteriorated corrosion-fatigue behavior was observed in the test environments. Under constant stress intensity factors, most samples did not show elevated crack growth rates, suggesting an adequate stress corrosion cracking resistance in the test environments. However, an unstable cracking behavior was observed in a 47-dpa sample, resulting in significantly higher crack growth rates than expected at high stress intensity factors. Crack instability was also observed in a 0.06-dpa sample but did not lead to a sustained high crack growth rate. The impact of neutron irradiation was more evident in the fracture toughness J-R curve tests. As the dose increased, the J-R curve declined considerably and became very shallow at high doses. A fully intergranular fracture morphology was also observed among the high-dose samples ruptured in an air atmosphere at room temperature. This brittle fracture mode in the absence of high temperature water environment confirmed a high degree of embrittlement of this material resulting from its service exposure to neutron irradiation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗