Results for “model diagnostics and development” — Page 28

DOE OSTI2025

Integrated modeling of RF-induced tungsten erosion at ICRH antenna structures in the WEST tokamak *

This paper introduces STRIPE (Simulated Transport of RF Impurity Production and Emission), an advanced modeling framework developed to analyze material erosion and the global transport of eroded impurities originating from radio-frequency (RF) antenna structures in magnetic confinement fusion devices. STRIPE integrates multiple physics modules: SolEdge3x for scrape-off-layer plasma profiles, COMSOL for 3D RF rectified sheath potentials, RustBCA for erosion yields and surface interactions, and global impurity transport for 3D ion energy-angle distributions and impurity transport. The framework is applied to an ion cyclotron RF-heated L-mode discharge (#57877) in the WEST tokamak, where it predicts a thirty-fold increase in gross tungsten erosion at antenna limiters during the transition from ohmic to ICRH operation. Additionally, under ICRH conditions, a tenfold enhancement in erosion is observed when comparing RF sheath effects to purely thermal sheath conditions. High-charge-state oxygen ions ($\mathrm{O}$ 6+ and above) are identified as the dominant contributors to tungsten sputtering. To validate the model, a synthetic diagnostic tool based on inverse photon efficiency (S/XB coefficients) from the ColRadPy collisional-radiative model enables direct comparison with spectroscopic measurements. Model predictions using a plasma composition of 1% oxygen and 99% deuterium show good agreement with observed W − I (400.9 nm) emission for discharge #57877, supporting the accuracy of the STRIPE framework. This study focuses specifically on gross erosion calculations to demonstrate STRIPE’s capabilities. Future extensions of this work will incorporate net erosion, re-deposition, self-sputtering effects, and whole-device modeling of sputtered tungsten impurity transport. STRIPE is also being applied to other RF-heated linear and toroidal devices, offering valuable insights for antenna design, impurity control, and performance optimization in next-generation fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Pedestal fluctuation measurements with charge exchange imaging at the DIII-D tokamak

A new high radial resolution 2D multichannel Charge eXchange Imaging (CXI) diagnostic is under development for deployment at DIII-D. Here, the diagnostic system will measure low-to-intermediate radial wavenumber carbon density fluctuations by observing the n = 8 – 7 (λ = 529.06 nm) C-VI emission line, resulting from charge exchange collisions between heating neutral beam atoms and the intrinsic carbon ion density. The new CXI diagnostic will provide measurements with ΔR ~ 0.4 cm to access higher k r instabilities (k r < 8 cm –1 ) predicted to arise in the steep-gradient region of the H-mode pedestal. The CXI system will feature 60 fiber bundles in a 12 × 5 arrangement, with each bundle consisting of four 1 mm fibers. A custom optical system has been designed to filter and image incoming signals onto an 8 × 8 avalanche photodiode array. Additionally, a novel electronics suite has been designed and commissioned to amplify and digitize the relatively low-intensity carbon signal at a 2 MHz bandwidth. Forward modeling results of the active C-VI emission suggest sufficient signal to noise ratios to resolve turbulent fluctuations. Prototype measurements demonstrate the ability to perform high frequency pedestal measurements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

2013-2014 Greater Fairbanks, Alaska, Transportation Survey

# 2013–2014 Greater Fairbanks, Alaska, Transportation Survey The 2013–2014 Greater Fairbanks Transportation Survey obtained behavior data for regional travel demand modeling. The planning region in Alaska comprised the North Star Borough—known as the PM2.5 nonattainment region—and included the cities of Fairbanks and North Pole. ## Data Collection Agency The Alaska Department of Transportation and Public Facilities conducted the survey. ## Methodology Data collection occurred in two phases: the first in fall 2013 and the second in winter 2014. The first phase employed address-based sampling to recruit more than 1,700 households for a one-day personal travel survey, and a sub-sample participated with global position system (GPS) and on-board diagnostic (OBD) loggers installed in their vehicles (282 vehicles) for one week. The purpose of phase one was to better understand the impact of vehicle emissions on air quality in the PM2.5 nonattainment region. Many of the households participating in the vehicle GPS/OBD portion of phase one were asked to participate in phase two. ## Drive Cycle Processing and Filtering NREL has developed a GPS data filtration routine to filter erroneous data points in individual drive cycles sourced from GPS devices mounted in vehicles. Second-by-second drive cycle data collected from GPS-instrumented vehicles during this survey have passed through NREL's drive cycle processing and filtering routines. ## Survey Records Survey records include 135 households. ## More Information For more information about the survey, see the [Greater Fairbanks Transportation Survey Final Report](https://www.nrel.gov/media/docs/libraries/tsdc/greater-fairbanks-transportation-survey-final-report.pdf?sfvrsn=16ecd45b_1). ## Transportation Data For details on available travel survey data and variable definitions, see the [data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/akdot_data_dictionary.pdf?sfvrsn=16778e11_1). NREL-generated drive cycle data are also available for this survey. For details on available data and variable definitions, see the [drive cycle data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/drive_cycles_data_dictionary.pdf?sfvrsn=7de7e888_1). Transportation data are available as zipped files. [Download Winzip](http://www.winzip.com/downwz.htm).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

2013-2014 Greater Fairbanks, Alaska, Transportation Survey

# 2013–2014 Greater Fairbanks, Alaska, Transportation Survey The 2013–2014 Greater Fairbanks Transportation Survey obtained behavior data for regional travel demand modeling. The planning region in Alaska comprised the North Star Borough—known as the PM2.5 nonattainment region—and included the cities of Fairbanks and North Pole. ## Data Collection Agency The Alaska Department of Transportation and Public Facilities conducted the survey. ## Methodology Data collection occurred in two phases: the first in fall 2013 and the second in winter 2014. The first phase employed address-based sampling to recruit more than 1,700 households for a one-day personal travel survey, and a sub-sample participated with global position system (GPS) and on-board diagnostic (OBD) loggers installed in their vehicles (282 vehicles) for one week. The purpose of phase one was to better understand the impact of vehicle emissions on air quality in the PM2.5 nonattainment region. Many of the households participating in the vehicle GPS/OBD portion of phase one were asked to participate in phase two. ## Drive Cycle Processing and Filtering NREL has developed a GPS data filtration routine to filter erroneous data points in individual drive cycles sourced from GPS devices mounted in vehicles. Second-by-second drive cycle data collected from GPS-instrumented vehicles during this survey have passed through NREL's drive cycle processing and filtering routines. ## Survey Records Survey records include 135 households. ## More Information For more information about the survey, see the [Greater Fairbanks Transportation Survey Final Report](https://www.nrel.gov/media/docs/libraries/tsdc/greater-fairbanks-transportation-survey-final-report.pdf?sfvrsn=16ecd45b_1). ## Transportation Data For details on available travel survey data and variable definitions, see the [data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/akdot_data_dictionary.pdf?sfvrsn=16778e11_1). NREL-generated drive cycle data are also available for this survey. For details on available data and variable definitions, see the [drive cycle data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/drive_cycles_data_dictionary.pdf?sfvrsn=7de7e888_1). Transportation data are available as zipped files. [Download Winzip](http://www.winzip.com/downwz.htm).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

2013-2014 Greater Fairbanks, Alaska, Transportation Survey

# 2013–2014 Greater Fairbanks, Alaska, Transportation Survey The 2013–2014 Greater Fairbanks Transportation Survey obtained behavior data for regional travel demand modeling. The planning region in Alaska comprised the North Star Borough—known as the PM2.5 nonattainment region—and included the cities of Fairbanks and North Pole. ## Data Collection Agency The Alaska Department of Transportation and Public Facilities conducted the survey. ## Methodology Data collection occurred in two phases: the first in fall 2013 and the second in winter 2014. The first phase employed address-based sampling to recruit more than 1,700 households for a one-day personal travel survey, and a sub-sample participated with global position system (GPS) and on-board diagnostic (OBD) loggers installed in their vehicles (282 vehicles) for one week. The purpose of phase one was to better understand the impact of vehicle emissions on air quality in the PM2.5 nonattainment region. Many of the households participating in the vehicle GPS/OBD portion of phase one were asked to participate in phase two. ## Drive Cycle Processing and Filtering NREL has developed a GPS data filtration routine to filter erroneous data points in individual drive cycles sourced from GPS devices mounted in vehicles. Second-by-second drive cycle data collected from GPS-instrumented vehicles during this survey have passed through NREL's drive cycle processing and filtering routines. ## Survey Records Survey records include 135 households. ## More Information For more information about the survey, see the [Greater Fairbanks Transportation Survey Final Report](https://www.nrel.gov/media/docs/libraries/tsdc/greater-fairbanks-transportation-survey-final-report.pdf?sfvrsn=16ecd45b_1). ## Transportation Data For details on available travel survey data and variable definitions, see the [data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/akdot_data_dictionary.pdf?sfvrsn=16778e11_1). NREL-generated drive cycle data are also available for this survey. For details on available data and variable definitions, see the [drive cycle data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/drive_cycles_data_dictionary.pdf?sfvrsn=7de7e888_1). Transportation data are available as zipped files. [Download Winzip](http://www.winzip.com/downwz.htm).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

2013-2014 Greater Fairbanks, Alaska, Transportation Survey

# 2013–2014 Greater Fairbanks, Alaska, Transportation Survey The 2013–2014 Greater Fairbanks Transportation Survey obtained behavior data for regional travel demand modeling. The planning region in Alaska comprised the North Star Borough—known as the PM2.5 nonattainment region—and included the cities of Fairbanks and North Pole. ## Data Collection Agency The Alaska Department of Transportation and Public Facilities conducted the survey. ## Methodology Data collection occurred in two phases: the first in fall 2013 and the second in winter 2014. The first phase employed address-based sampling to recruit more than 1,700 households for a one-day personal travel survey, and a sub-sample participated with global position system (GPS) and on-board diagnostic (OBD) loggers installed in their vehicles (282 vehicles) for one week. The purpose of phase one was to better understand the impact of vehicle emissions on air quality in the PM2.5 nonattainment region. Many of the households participating in the vehicle GPS/OBD portion of phase one were asked to participate in phase two. ## Drive Cycle Processing and Filtering NREL has developed a GPS data filtration routine to filter erroneous data points in individual drive cycles sourced from GPS devices mounted in vehicles. Second-by-second drive cycle data collected from GPS-instrumented vehicles during this survey have passed through NREL's drive cycle processing and filtering routines. ## Survey Records Survey records include 135 households. ## More Information For more information about the survey, see the [Greater Fairbanks Transportation Survey Final Report](https://www.nrel.gov/media/docs/libraries/tsdc/greater-fairbanks-transportation-survey-final-report.pdf?sfvrsn=16ecd45b_1). ## Transportation Data For details on available travel survey data and variable definitions, see the [data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/akdot_data_dictionary.pdf?sfvrsn=16778e11_1). NREL-generated drive cycle data are also available for this survey. For details on available data and variable definitions, see the [drive cycle data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/drive_cycles_data_dictionary.pdf?sfvrsn=7de7e888_1). Transportation data are available as zipped files. [Download Winzip](http://www.winzip.com/downwz.htm).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

2013-2014 Greater Fairbanks, Alaska, Transportation Survey

# 2013–2014 Greater Fairbanks, Alaska, Transportation Survey The 2013–2014 Greater Fairbanks Transportation Survey obtained behavior data for regional travel demand modeling. The planning region in Alaska comprised the North Star Borough—known as the PM2.5 nonattainment region—and included the cities of Fairbanks and North Pole. ## Data Collection Agency The Alaska Department of Transportation and Public Facilities conducted the survey. ## Methodology Data collection occurred in two phases: the first in fall 2013 and the second in winter 2014. The first phase employed address-based sampling to recruit more than 1,700 households for a one-day personal travel survey, and a sub-sample participated with global position system (GPS) and on-board diagnostic (OBD) loggers installed in their vehicles (282 vehicles) for one week. The purpose of phase one was to better understand the impact of vehicle emissions on air quality in the PM2.5 nonattainment region. Many of the households participating in the vehicle GPS/OBD portion of phase one were asked to participate in phase two. ## Drive Cycle Processing and Filtering NREL has developed a GPS data filtration routine to filter erroneous data points in individual drive cycles sourced from GPS devices mounted in vehicles. Second-by-second drive cycle data collected from GPS-instrumented vehicles during this survey have passed through NREL's drive cycle processing and filtering routines. ## Survey Records Survey records include 135 households. ## More Information For more information about the survey, see the [Greater Fairbanks Transportation Survey Final Report](https://www.nrel.gov/media/docs/libraries/tsdc/greater-fairbanks-transportation-survey-final-report.pdf?sfvrsn=16ecd45b_1). ## Transportation Data For details on available travel survey data and variable definitions, see the [data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/akdot_data_dictionary.pdf?sfvrsn=16778e11_1). NREL-generated drive cycle data are also available for this survey. For details on available data and variable definitions, see the [drive cycle data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/drive_cycles_data_dictionary.pdf?sfvrsn=7de7e888_1). Transportation data are available as zipped files. [Download Winzip](http://www.winzip.com/downwz.htm).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

2013-2014 Greater Fairbanks, Alaska, Transportation Survey

# 2013–2014 Greater Fairbanks, Alaska, Transportation Survey The 2013–2014 Greater Fairbanks Transportation Survey obtained behavior data for regional travel demand modeling. The planning region in Alaska comprised the North Star Borough—known as the PM2.5 nonattainment region—and included the cities of Fairbanks and North Pole. ## Data Collection Agency The Alaska Department of Transportation and Public Facilities conducted the survey. ## Methodology Data collection occurred in two phases: the first in fall 2013 and the second in winter 2014. The first phase employed address-based sampling to recruit more than 1,700 households for a one-day personal travel survey, and a sub-sample participated with global position system (GPS) and on-board diagnostic (OBD) loggers installed in their vehicles (282 vehicles) for one week. The purpose of phase one was to better understand the impact of vehicle emissions on air quality in the PM2.5 nonattainment region. Many of the households participating in the vehicle GPS/OBD portion of phase one were asked to participate in phase two. ## Drive Cycle Processing and Filtering NREL has developed a GPS data filtration routine to filter erroneous data points in individual drive cycles sourced from GPS devices mounted in vehicles. Second-by-second drive cycle data collected from GPS-instrumented vehicles during this survey have passed through NREL's drive cycle processing and filtering routines. ## Survey Records Survey records include 135 households. ## More Information For more information about the survey, see the [Greater Fairbanks Transportation Survey Final Report](https://www.nrel.gov/media/docs/libraries/tsdc/greater-fairbanks-transportation-survey-final-report.pdf?sfvrsn=16ecd45b_1). ## Transportation Data For details on available travel survey data and variable definitions, see the [data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/akdot_data_dictionary.pdf?sfvrsn=16778e11_1). NREL-generated drive cycle data are also available for this survey. For details on available data and variable definitions, see the [drive cycle data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/drive_cycles_data_dictionary.pdf?sfvrsn=7de7e888_1). Transportation data are available as zipped files. [Download Winzip](http://www.winzip.com/downwz.htm).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

2013-2014 Greater Fairbanks, Alaska, Transportation Survey

# 2013–2014 Greater Fairbanks, Alaska, Transportation Survey The 2013–2014 Greater Fairbanks Transportation Survey obtained behavior data for regional travel demand modeling. The planning region in Alaska comprised the North Star Borough—known as the PM2.5 nonattainment region—and included the cities of Fairbanks and North Pole. ## Data Collection Agency The Alaska Department of Transportation and Public Facilities conducted the survey. ## Methodology Data collection occurred in two phases: the first in fall 2013 and the second in winter 2014. The first phase employed address-based sampling to recruit more than 1,700 households for a one-day personal travel survey, and a sub-sample participated with global position system (GPS) and on-board diagnostic (OBD) loggers installed in their vehicles (282 vehicles) for one week. The purpose of phase one was to better understand the impact of vehicle emissions on air quality in the PM2.5 nonattainment region. Many of the households participating in the vehicle GPS/OBD portion of phase one were asked to participate in phase two. ## Drive Cycle Processing and Filtering NREL has developed a GPS data filtration routine to filter erroneous data points in individual drive cycles sourced from GPS devices mounted in vehicles. Second-by-second drive cycle data collected from GPS-instrumented vehicles during this survey have passed through NREL's drive cycle processing and filtering routines. ## Survey Records Survey records include 135 households. ## More Information For more information about the survey, see the [Greater Fairbanks Transportation Survey Final Report](https://www.nrel.gov/media/docs/libraries/tsdc/greater-fairbanks-transportation-survey-final-report.pdf?sfvrsn=16ecd45b_1). ## Transportation Data For details on available travel survey data and variable definitions, see the [data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/akdot_data_dictionary.pdf?sfvrsn=16778e11_1). NREL-generated drive cycle data are also available for this survey. For details on available data and variable definitions, see the [drive cycle data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/drive_cycles_data_dictionary.pdf?sfvrsn=7de7e888_1). Transportation data are available as zipped files. [Download Winzip](http://www.winzip.com/downwz.htm).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

2013-2014 Greater Fairbanks, Alaska, Transportation Survey

# 2013–2014 Greater Fairbanks, Alaska, Transportation Survey The 2013–2014 Greater Fairbanks Transportation Survey obtained behavior data for regional travel demand modeling. The planning region in Alaska comprised the North Star Borough—known as the PM2.5 nonattainment region—and included the cities of Fairbanks and North Pole. ## Data Collection Agency The Alaska Department of Transportation and Public Facilities conducted the survey. ## Methodology Data collection occurred in two phases: the first in fall 2013 and the second in winter 2014. The first phase employed address-based sampling to recruit more than 1,700 households for a one-day personal travel survey, and a sub-sample participated with global position system (GPS) and on-board diagnostic (OBD) loggers installed in their vehicles (282 vehicles) for one week. The purpose of phase one was to better understand the impact of vehicle emissions on air quality in the PM2.5 nonattainment region. Many of the households participating in the vehicle GPS/OBD portion of phase one were asked to participate in phase two. ## Drive Cycle Processing and Filtering NREL has developed a GPS data filtration routine to filter erroneous data points in individual drive cycles sourced from GPS devices mounted in vehicles. Second-by-second drive cycle data collected from GPS-instrumented vehicles during this survey have passed through NREL's drive cycle processing and filtering routines. ## Survey Records Survey records include 135 households. ## More Information For more information about the survey, see the [Greater Fairbanks Transportation Survey Final Report](https://www.nrel.gov/media/docs/libraries/tsdc/greater-fairbanks-transportation-survey-final-report.pdf?sfvrsn=16ecd45b_1). ## Transportation Data For details on available travel survey data and variable definitions, see the [data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/akdot_data_dictionary.pdf?sfvrsn=16778e11_1). NREL-generated drive cycle data are also available for this survey. For details on available data and variable definitions, see the [drive cycle data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/drive_cycles_data_dictionary.pdf?sfvrsn=7de7e888_1). Transportation data are available as zipped files. [Download Winzip](http://www.winzip.com/downwz.htm).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

2013-2014 Greater Fairbanks, Alaska, Transportation Survey

# 2013–2014 Greater Fairbanks, Alaska, Transportation Survey The 2013–2014 Greater Fairbanks Transportation Survey obtained behavior data for regional travel demand modeling. The planning region in Alaska comprised the North Star Borough—known as the PM2.5 nonattainment region—and included the cities of Fairbanks and North Pole. ## Data Collection Agency The Alaska Department of Transportation and Public Facilities conducted the survey. ## Methodology Data collection occurred in two phases: the first in fall 2013 and the second in winter 2014. The first phase employed address-based sampling to recruit more than 1,700 households for a one-day personal travel survey, and a sub-sample participated with global position system (GPS) and on-board diagnostic (OBD) loggers installed in their vehicles (282 vehicles) for one week. The purpose of phase one was to better understand the impact of vehicle emissions on air quality in the PM2.5 nonattainment region. Many of the households participating in the vehicle GPS/OBD portion of phase one were asked to participate in phase two. ## Drive Cycle Processing and Filtering NREL has developed a GPS data filtration routine to filter erroneous data points in individual drive cycles sourced from GPS devices mounted in vehicles. Second-by-second drive cycle data collected from GPS-instrumented vehicles during this survey have passed through NREL's drive cycle processing and filtering routines. ## Survey Records Survey records include 135 households. ## More Information For more information about the survey, see the [Greater Fairbanks Transportation Survey Final Report](https://www.nrel.gov/media/docs/libraries/tsdc/greater-fairbanks-transportation-survey-final-report.pdf?sfvrsn=16ecd45b_1). ## Transportation Data For details on available travel survey data and variable definitions, see the [data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/akdot_data_dictionary.pdf?sfvrsn=16778e11_1). NREL-generated drive cycle data are also available for this survey. For details on available data and variable definitions, see the [drive cycle data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/drive_cycles_data_dictionary.pdf?sfvrsn=7de7e888_1). Transportation data are available as zipped files. [Download Winzip](http://www.winzip.com/downwz.htm).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

2013-2014 Greater Fairbanks, Alaska, Transportation Survey

# 2013–2014 Greater Fairbanks, Alaska, Transportation Survey The 2013–2014 Greater Fairbanks Transportation Survey obtained behavior data for regional travel demand modeling. The planning region in Alaska comprised the North Star Borough—known as the PM2.5 nonattainment region—and included the cities of Fairbanks and North Pole. ## Data Collection Agency The Alaska Department of Transportation and Public Facilities conducted the survey. ## Methodology Data collection occurred in two phases: the first in fall 2013 and the second in winter 2014. The first phase employed address-based sampling to recruit more than 1,700 households for a one-day personal travel survey, and a sub-sample participated with global position system (GPS) and on-board diagnostic (OBD) loggers installed in their vehicles (282 vehicles) for one week. The purpose of phase one was to better understand the impact of vehicle emissions on air quality in the PM2.5 nonattainment region. Many of the households participating in the vehicle GPS/OBD portion of phase one were asked to participate in phase two. ## Drive Cycle Processing and Filtering NREL has developed a GPS data filtration routine to filter erroneous data points in individual drive cycles sourced from GPS devices mounted in vehicles. Second-by-second drive cycle data collected from GPS-instrumented vehicles during this survey have passed through NREL's drive cycle processing and filtering routines. ## Survey Records Survey records include 135 households. ## More Information For more information about the survey, see the [Greater Fairbanks Transportation Survey Final Report](https://www.nrel.gov/media/docs/libraries/tsdc/greater-fairbanks-transportation-survey-final-report.pdf?sfvrsn=16ecd45b_1). ## Transportation Data For details on available travel survey data and variable definitions, see the [data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/akdot_data_dictionary.pdf?sfvrsn=16778e11_1). NREL-generated drive cycle data are also available for this survey. For details on available data and variable definitions, see the [drive cycle data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/drive_cycles_data_dictionary.pdf?sfvrsn=7de7e888_1). Transportation data are available as zipped files. [Download Winzip](http://www.winzip.com/downwz.htm).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

2013-2014 Greater Fairbanks, Alaska, Transportation Survey

# 2013–2014 Greater Fairbanks, Alaska, Transportation Survey The 2013–2014 Greater Fairbanks Transportation Survey obtained behavior data for regional travel demand modeling. The planning region in Alaska comprised the North Star Borough—known as the PM2.5 nonattainment region—and included the cities of Fairbanks and North Pole. ## Data Collection Agency The Alaska Department of Transportation and Public Facilities conducted the survey. ## Methodology Data collection occurred in two phases: the first in fall 2013 and the second in winter 2014. The first phase employed address-based sampling to recruit more than 1,700 households for a one-day personal travel survey, and a sub-sample participated with global position system (GPS) and on-board diagnostic (OBD) loggers installed in their vehicles (282 vehicles) for one week. The purpose of phase one was to better understand the impact of vehicle emissions on air quality in the PM2.5 nonattainment region. Many of the households participating in the vehicle GPS/OBD portion of phase one were asked to participate in phase two. ## Drive Cycle Processing and Filtering NREL has developed a GPS data filtration routine to filter erroneous data points in individual drive cycles sourced from GPS devices mounted in vehicles. Second-by-second drive cycle data collected from GPS-instrumented vehicles during this survey have passed through NREL's drive cycle processing and filtering routines. ## Survey Records Survey records include 135 households. ## More Information For more information about the survey, see the [Greater Fairbanks Transportation Survey Final Report](https://www.nrel.gov/media/docs/libraries/tsdc/greater-fairbanks-transportation-survey-final-report.pdf?sfvrsn=16ecd45b_1). ## Transportation Data For details on available travel survey data and variable definitions, see the [data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/akdot_data_dictionary.pdf?sfvrsn=16778e11_1). NREL-generated drive cycle data are also available for this survey. For details on available data and variable definitions, see the [drive cycle data dictionary](https://www.nrel.gov/media/docs/libraries/tsdc/drive_cycles_data_dictionary.pdf?sfvrsn=7de7e888_1). Transportation data are available as zipped files. [Download Winzip](http://www.winzip.com/downwz.htm).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2023

Development of fracture diagnostic methods for fluid distribution based on quantitative interpretation of distributed acoustic sensing and distributed temperature sensing

Multistage hydraulic fracturing design on horizontal wells has significantly evolved with larger fluid volume, more fracturing stages, and tighter perforation cluster spacing to efficiently stimulate unconventional reservoirs. From the published field observations, the recent fracturing design results in complex fracture networks or swarm of fractures. Fracture treatment evaluation is extremely challenging in such a case because of the large amount of variables in well completion and stimulation design. Combined measurements from different technologies can help in fracture diagnosis. Fluid distribution, either during fracture injection or during production, directly relates to the stimulation efficiency at the cluster level and at the stage level. Because it is unlikely in the real world to distribute the injected fluid uniformly among all the clusters, we need diagnostic techniques to generate the flow profile along a lateral. Fiber-optic measurements, such as distributed acoustic sensing (DAS) and distributed temperature sensing (DTS), are currently used to diagnose downhole flow conditions. This technology allows us to qualitatively confirm the fluid flow profile and other issues occurring downhole during fracturing such as leakage through plugs. For optimizing a fracturing design, we also need to understand how the design parameters are correlated with the stimulation efficiency. In this study, we combine two sets of models of DAS and DTS data interpretation for injected fluid volume distribution. The DAS is interpreted based on an empirical correlation between fluid flow rates and frequency band energy from the acoustic signals. The DTS is interpreted by performing temperature history match-based thermal energy conservation. Because of the completely different physics behind the interpretations, the confirmation of two interpretations provides confidence in fluid distribution.

Geochemistry & Geophysics↗

DOE OSTI2020

Estimation of elastic properties of an additively manufactured lattice using resonant ultrasound spectroscopy

Development of improved approaches in the characterization of additively manufactured structures continues to be a topic of interest for the advanced manufacturing community. This article will investigate an approach using resonant ultrasound spectroscopy (RUS) to determine the effective elastic constants of an orthotropic lattice structure. The evaluation is performed on a cube shaped 316 L stainless steel test specimen, constructed using selective laser melting techniques. The approach uses RUS techniques in conjunction with the assumption that in the frequency regime of interest, the wavelength of the diagnostic ultrasound is greater than the discrete structural features of the unit cell of the lattice; thus, the AM structure can be treated as an anisotropic continuum with effective material properties and symmetry inherited from the unit cell. The RUS analysis estimates the nine elastic coefficients associated with orthotropic sample symmetry, which, in turn, are used to determine the elastic moduli and Poisson ratios. Current results show good agreement between experiments and modeled data. Comparisons to published results are also in good agreement, indicating the potential applicability of this characterization technique for estimating the linear elastic properties of innovative additive manufactured metal lattice structures.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Plasma Guns for Magnetized Fuel Targets for PJMIF

In plasma jet driven magneto-inertial fusion (PJMIF) an array of discrete supersonic plasma jets is used to form a spherically imploding plasma liner, which then compresses a magnetized plasma target to fusion conditions. With funding from ARPA-E’s ALPHA program and from Strong Atomics LLC, HyperJet Fusion Corp and HyperV Technologies Corp. previously developed the plasma guns required for an experimental demonstration of the plasma liner formation part of the concept. A 36-gun demonstration of an imploding spherical plasma liner is currently underway on the PLX facility at Los Alamos National Laboratory. This present project addresses the next step required for a complete PJMIF concept, i.e. developing the magnetized plasma target. We proposed to form the target by stagnating a number of magnetized plasma jets in the center of the target chamber. This is accomplished by adding a bias field coil to the plasma liner gun to form a magnetized plasma jet. This experimental development took place at HyperJet in a geometry replicating the bias field environment that will be seen on a PLX port so the results are directly transferrable to the PLX experiment. The objective of this effort was the technical development and characterization of a new magnetized plasma jet using a high-performance, high momentum flux, contoured-gap coaxial plasma gun appropriate for use on the next stage of the PLX experiment. Electromagnetic modeling of the coil indicated the coil was best placed around the aluminum tubes of the gun transmission line, rather than around the chamber port as originally proposed. This maximized field strength in the breech and yielded much better flux linkage between gun electrodes. A 30-turn coil was ultimately implemented, allowing long pulses that could diffuse through the metal walls on the timescale of interest. \machtwo modeling predicted that less capacitance in the main PFN could potentially improve plasma jet velocities due to better matching of the current to the smaller plasma mass and the existing electrode contour designed to suppress blowby. This proved true, as testing showed markedly improved performance when the original 600uF bank was reduced to 400uF. A number of diagnostics were built and/or upgraded in order to characterize the plasma jets, inluding laser interferomtery for density, photodiodes for velocity, Bdot probes for magnetic field measurements, a Triple probe for temperature measurements, and spectroscopy for impurity content. A plasma gun with the 30-turn magnet coil installed, a 70% reduction in gas valve plenum volume, and a 33% reduction in main PFN capacitance produced a dense, high velocity, well magnetized plasma jet. We met or exceeded virtually all of the plasma jet parameter goals. Peak velocity of 135 km/s exceeded the 100 km/s goal by 35%, while the peak density of over 1.0x10 15 cm -3 was 3.3 times the goal of >3.0x10 14 cm -3 . Shot-to-shot repeatability is excellent, with a jitter of less than 300ns observed on the arrival fronts of the photodiode signals from one shot to the next. Average plasma jet lengths of 33cm (at 120km/s) were slightly longer than the 20cm goal, but jets as short as 11.8cm were observed at 135km/s. Mass is much higher than the targeted goal, averaging 106ug per shot compared to 20ug. The magnetic field is still a bit lower than desired, with a maximum to date of ~811G, compared to the goal of 1000G. Average values, though, were typically in the 300-450G range, when measured further downstream after some expected in flight decay. Temperature measurements are still a work in progress. Increasing the B field and completing temperature measurements will be continued on into the ongoing BETHE project.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Near-Surface Imaging of the Multicomponent Gas Phase above a Silver Catalyst during Partial Oxidation of Methanol

Fundamental chemistry in heterogeneous catalysis is increasingly explored using operando techniques in order to address the pressure gap between ultrahigh vacuum studies and practical operating pressures. Because most operando experiments focus on the surface and surface-bound species, there is a knowledge gap of the near-surface gas phase and the fundamental information the properties of this region convey about catalytic mechanisms. In this work, we demonstrate in situ visualization and measurement of gas-phase species and temperature distributions in operando catalysis experiments using complementary near-surface optical and mass spectrometry techniques. The partial oxidation of methanol over a silver catalyst demonstrates the value of these diagnostic techniques at 600 Torr (800 mbar) pressure and temperatures from 150 to 410 °C. Planar laser-induced fluorescence provides two-dimensional images of the formaldehyde product distribution that show the development of the boundary layer above the catalyst under different flow conditions. Raman scattering imaging provides measurements of a wide range of major species, such as methanol, oxygen, nitrogen, formaldehyde, and water vapor. Near-surface molecular beam mass spectrometry enables simultaneous detection of all species using a gas sampling probe. Detection of gas-phase free radicals, such as CH 3 and CH 3 O, and of minor products, such as acetaldehyde, dimethyl ether, and methyl formate, provides insights into catalytic mechanisms of the partial oxidation of methanol. The combination of these techniques provides a detailed picture of the coupling between the gas phase and surface in heterogeneous catalysis and enables parametric studies under different operating conditions, which will enhance our ability to constrain microkinetic models of heterogeneous catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

A multi-modal scanning system to digitize CBRNE emergency response scenes

A handheld system developed to digitize a contextual understanding of the scene at a chemical, biological, radiological, nuclear and/or explosives (CBRNE) events is described. The system uses LiDAR and cameras to create a colorized 3D model of the environment, which helps domain experts that are supporting responders in the field. To generate the digitized model, a responder scans any suspicious objects and the surroundings by carrying the system through the scene. The scanning system provides a real-time user interface to inform the user about scanning progress and to indicate any areas that may have been missed either by the LiDAR sensors or the cameras. Currently, the collected data are post-processed on a different device, building a colorized triangular mesh of the encountered scene, with the intention of moving this pipeline to the scanner at a later point. The mesh is sufficiently compressed to be sent over a reduced bandwidth connection to a remote analyst. Furthermore, the system tracks fiducial markers attached to diagnostic equipment that is placed around the suspicious object. The resulting tracking information can be transmitted to remote analysts to further facilitate their supporting efforts. The paper will discuss the system's design, software components, the user interface used for scanning a scene, the necessary procedures for calibration of the sensors, and the processing steps of the resulting data. The discussion will close by evaluating the system's performance on 11 scenes.

Salathe, Marco↗