Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “materials simulations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Simulation and characterization of cation disorder in ZnGeP 2

New optoelectronic materials are needed for improving the efficiency and reliability of devices such as solar cells. Cation ordering presents one means of controlling optoelectronic properties while introducing potential to also diversify the mineral constituents of electronic devices; however, the mechanisms of ordering are not yet well understood. To better understand cation ordering in a system integratable with current devices, we assess short- and long-range order parameters of ZnGeP 2 , a material closely lattice matched to Si. Structures are simulated using cluster-based Monte Carlo and first-principles calculations to compare structural distortions, periodicity, and local coordination environments in ZnGeP 2 to experimental data both from the literature and presented here. Comparing order parameters, we relate the transition in order parameters of ZnGeP 2 to that of ZnGeP 2 , discuss the reduction of band gaps with disorder, and show that traditional structural characterization alone is insufficient for understanding order in ZnGeP 2 .

14 SOLAR ENERGY↗
DOE OSTI2020

Solvent–Solvent Correlations across Graphene: The Effect of Image Charges

Wetting experiments show pure graphene to be weakly hydrophilic, but its contact angle (CA) also reflects the character of the supporting material. Measurements and Molecular Dynamics simulations on suspended and supported graphene often reveal a CA reduction due to the presence of the supporting substrate. A similar reduction is consistently observed when graphene is wetted from both sides. The effect has been attributed to transparency to molecular interactions across the graphene sheet, however, the possibility of substrate-induced graphene polarization has also been considered. Computer simulations of CA on graphene have so far been determined by ignoring the material’s conducting properties. We improve the graphene model by incorporating its conductivity according to the Constant Applied Potential Molecular Dynamics. Using this method, we compare the wettabilities of suspended graphene and graphene supported by water by measuring the CA of cylindrical water drops on the sheets. The inclusion of graphene conductivity and concomitant polarization effects lead to a lower CA on suspended graphene but the CA reduction is significantly bigger when the sheets are also wetted from the opposite side. The stronger adhesion is accompanied by a profound change in the correlations among water molecules across the sheet. While partial charges on water molecules interacting across an insulator sheet attract charges of the opposite sign, apparent attraction among like charges is manifested across the conducting graphene. The change is associated with graphene polarization, as the image charges inside the conductor attract equally signed partial charges of water molecules on both sides of the sheet. Additionally, by using a non-polar liquid (diiodomethane), we affirm a detectable wetting translucency when liquid-liquid forces are dominated by dispersive interactions. Furthermore, our findings are important for predictive modeling toward a variety of applications including sensors, fuel cell membranes, water filtration, and graphene-based electrode materials in high-performance supercapacitors.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

GeoMelt{sup R} In-Container Vitrification (ICV){sup TM} for Fukushima Daiichi Water Treatment Secondary Wastes - 20212

The Japanese government is supporting development work implemented jointly by Veolia subsidiaries Kurion Japan, K.K., Veolia Nuclear Solutions (VNS), Inc., and Veolia Nuclear Solutions Federal Services, LLC for treating radioactive waste generated from Fukushima Daiichi Nuclear Power Station (NPS) water treatment using the GeoMelt{sup TM} In-Container Vitrification (ICV){sup TM} technology. The initial work consisted of glass formulation and engineering-scale testing which was completed in 2018, in the frame of an IRID (International Research Institute for Nuclear Decommissioning) program as part of a project subsidized by Japan's Ministry of Economy, Trade and Industry (METI). The Fukushima Daiichi NPS Mid- and Long-Term Road-map requires investigation of methods to stabilize solid wastes (and to immobilize radioisotopes in the wastes) generated as a result of emergency response and decommissioning activities. Cooling water treatment has resulted in a significant amount of solid and slurry secondary wastes (mostly adsorbents and ion-exchange materials) which will require processing at some point. GeoMelt{sup R} ICV{sup TM} is a joule-heated melter technology which uses a refractory-lined single-use container combining the melter and disposal container. There is no pouring required nor concerns with refractory corrosion which allows the process to accommodate a wide range of waste chemistries and high waste loadings. The testing described here consisted of three engineering-scale melts, each processing between 212 kg and 240 kg of waste simulants, glass formers, and non-radioactive cesium (Cs) and strontium (Sr) tracers. Continuous isokinetic stack sampling of off-gas emissions was performed for each test in order to calculate Cs and Sr retention in the glass wasteform. Single-pass retention of Cs in the final glass wasteform ranged from 91.46 to 99.30%, and single-pass retention of Sr ranged from 99.76 to 100%. Planned particulate recycle will increase these retention levels. Melt 1 processed a mixture of KUR-EH (a zeolite-based ion-exchange material), simulated Advanced Liquid Processing System (ALPS) Carbonate and Iron Slurries, and glass additives. Melt 2 processed a mixture of KUR-EH, KUR-TSG (a titanate-based adsorbent), and glass additives. Melt 3 processed a mixture of KUR-EH, simulated barium sulfate/iron ferrocyanide sludge (AREVA sludge), and glass additives. Waste loadings for these melts ranged from 70 weight percent (wt%) to 82 wt%. Vitrification produces a waste form much denser than the stored water treatment secondary waste wastes, resulting in significant volume reduction. Volume reductions for the three tests ranged from 74 to 79 vol%. Vitrification produces a chemically durable wasteform. Pacific Northwest National Laboratory (PNNL) tested three glass samples from each engineering-scale melt) by the Materials Characterization Center 1 (MCC-1) test, an international standard leach test of the chemical durability of nuclear waste glasses. PNNL also obtained one U.S. reference glass (EA Glass) and two Japan reference glasses P0798) and tested these under the same MCC-1 conditions (90 deg. C, 10 m-1, DIW, and 7, 14, 28-day) as the GeoMelt{sup R} ICV{sup TM} glasses. The GeoMelt{sup R} ICV{sup TM} glasses exhibited lower total normalized releases and 14- to 28-day normalized release rates than the three reference glasses. These results suggest that the GeoMelt{sup R} ICV{sup TM} glasses have durabilities on par with high-level waste glasses under standard test conditions. Post-melt process sampling and analysis indicated no Cs migration into the melter refractory materials and very little deposition of Cs or Sr onto the melter hood or off-gas piping internals. The results of the testing indicated good Cs retention in the glass, high volume reduction and waste loadings, and excellent chemical durability. These factors are important to minimize treatment costs and to protect workers and the environment. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Empirical Model of Puncture Energy for Metals

The purpose of this work is to fit a previously developed empirical equation for puncture energy to simulation data. The conservative puncture energy equation could be used to expedite the process of performing calculations in the development of safety measures, avoiding the need to create complex finite element models for specific puncture scenarios. A total of 108 simulations are developed by varying coupon thickness, coupon material, probe shape, and probe diameter. The simulations are comprised of a low-velocity probe puncturing the coupons, from which the probe kinetic energy change is calculated. The empirical equation is fit to the dimensions, material properties, and energy results using a non-linear least-squares regression method within Python, which determines the two constant parameters for each fit. More statistically significant fit results are achieved by separating the data by probe shape and coupon material.

42 ENGINEERING↗
DOE OSTI2022

Iodine Removal in the DFLAW Flow-Sheet

In support of the WTP project, off-gas system and regulatory testing has been conducted previously on the DM1200 pilot melter equipped with a prototypical off-gas system installed at The Catholic University of America’s Vitreous State Laboratory (VSL). During the regulatory tests, an AC-S test bed filled with Kombisorb BAT 37 was included in the prototypical off-gas system and evaluated for response to HLW and LAW exhaust streams. Offline testing and small-scale testing of that media were also conducted. Testing demonstrated that a temperature rise occurred in the activated carbon media when water vapor was first introduced to virgin Kombisorb BAT 37, in response to high nitrogen oxide concentrations, and in response to the presence of organic compounds. Conditioning of the test bed by gradually increasing the NOx concentration prior to the introduction of organics was found to be an important operational strategy for preventing larger temperature excursions. However, no mercury was present in the exhaust stream during DM1200 testing and therefore comparable test data for mercury removal efficiency or temperature response of the carbon media in the presence of mercury were not collected in the DM1200 tests. In view of the need for data on mercury removal performance, BNI contracted with Atkins and the VSL to install and operate a suitable test system at VSL to collect the required data. That testing was designed to assess the performance of Kombisorb BAT-37 and the guard bed material, Sofnolime RG, for simulated melter exhaust streams that contain the highest concentrations of mercury, nitrogen oxides, acid gases, and organic compounds expected in WTP LAW melter exhaust. During shakedown testing with the new system, however, it became evident that a number of issues with Sofnolime RG as the guard bed material would render it unsuitable for this application. BNI subsequently determined that the guard bed was redundant for removal of acid gases since they could be adequately removed by the SBS and WESP. However, since the guard bed material was also credited with significant iodine removal , there was a need for a replacement material that would adequately perform that role. BNI identified several candidate media but performance data in gas compositions that are representative of the WTP LAW off-gas were not available. Accordingly, there was a need to test and evaluate the performance of these candidate media prior to performing the originally-planned tests. To that end, small scale tests were conducted to assess the performance of various adsorbents in simulated melter exhaust streams that contain mercury, iodine, nitrogen oxides, acid gases, and acetonitrile, which are expected to be present in WTP LAW melter exhaust.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Next Generation Co-Molded One-Piece Automotive Parts

The purpose of this project was to determine the feasibility of co-molding Class A Sheet Molding Compound (SMC), structural SMC, and continuous fiber prepreg materials to produce a single piece co-molded automotive part, such as a hood. The combination of the three molding materials and the incorporation of selective design features (ribs, flanges, corrugations) was expected to eliminate the need for inner reinforcement panels, significantly reducing tooling costs and simplifying the manufacturing process. A multi-material solution would also result in significant weight savings. The scope of this project included the material characterization of the three materials, development of cure and flow simulation models, and validation of the models against parts molded with different combinations of the materials on an 11”x11” plaque tool with rib features. The intent of this project was to apply the learnings obtained from co-molding a part with simplified geometry to a Phase 2 project that would produce a single piece hood, co-molded with the same materials. Resins from INEOS Composites were provided to IDI to produce SMC and continuous fiber prepregs. Purdue University and INEOS Composites characterized the rheological and curing behavior of the different materials as well as the mechanical properties of the co-molded parts. This data was used by Purdue University to create simulation models. Models were created to predict both flow patterns and predict mechanical properties of different laminate constructions in and around the ribs. Michigan State University - Corktown validated Purdue’s models by co-molding the three materials in different combinations on a tool containing rib features provided by Century Tool. The co-molded parts were evaluated against the simulation models by Purdue, Corktown and INEOS. The project team demonstrated the following: • The ability to obtain a cohesive co-molded structure made up of Class A SMC, Structural SMC, and continuous fiber prepreg. • The ability to obtain a co-molded part with a Class A surface • Modeling of flow and fiber orientation • Modeling to predict mechanical properties of multi-material co-molded structures The predicted flow behavior and fiber orientation from simulations were then compared with the molded samples. Exact local orientation state was difficult to compare between microscopy and flow simulation, but captured general trends. Multi-material flow behavior was generally modeled well with SMC materials, but the introduction of woven material sheets requires further model development. Purdue compared the predicted versus actual mechanical properties, and INEOS Composites evaluated the surface appearance of unpainted and painted co-molded parts. The models developed by Purdue demonstrated that the mechanical properties can be predicted for parts with varying material configurations. The resulting models can be applied to future co-molded part design, tooling design, and molding conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Computing material volume fractions on a superimposed mesh as applied to Monte Carlo particle transport simulations

Here, we present a newly implemented ray tracing algorithm in OpenMC for efficiently computing material volume fractions on superimposed meshes in complex geometries. By firing rays along each coordinate direction through the geometry, the approach accumulates track-length data in each mesh element, thereby determining the fractional composition of each material. Scaling studies on three different models—a random tetrahedra configuration, the Frascati Neutron Generator ITER dose rate benchmark, and a stellarator design—show excellent parallel performance, with nearly linear speedup on modern multi-threaded and distributed-memory systems. An analysis of the residual error relative to high-resolution reference solutions demonstrated that under optimal conditions it decreases as 1/R, where R is the number of rays fired, making it straightforward to achieve user-prescribed accuracy. This new functionality enables practical, mesh-based approaches for detailed nuclear analyses in production Monte Carlo workflows without resorting to expensive, fully conformal or unstructured meshing.

Monte Carlo↗
DOE OSTI2021

Safely probing the chemistry of Chernobyl nuclear fuel using micro-focus X-ray analysis

Detailed chemical analysis of the solidified molten fuel still residing in the stricken Chernobyl reactor unit 4 are inferred using multi-modal micro-focus X-ray analysis of a low-radioactivity proxy. A fascinating mixture of molten UO 2 , nuclear fuel cladding, concrete, stainless steel and other nuclear reactor components, these materials behaved like lava, solidifying to form a complex, highly radioactive glass-ceramic. Using element-specific chemical probes (micro-X-ray fluorescence and X-ray absorption spectroscopy), coupled with micro-diffraction analysis, the crystalline phase assemblage of simulants of these heterogeneous materials was established, which included “chernobylite” and a range of compositions in the (U 1-x Zr x )O 2 solid solution. Novel insight to nuclear accident fuel chemistry was obtained by establishing the oxidation state and local coordination of uranium not only in these crystalline phases, but uniquely in the amorphous fraction of the material, which varied depending on the history of the nuclear lava as it flowed through the reactor. This study demonstrates that micro-focus X-ray analysis of very small fractions of material can yield rich chemical information, which can be applied to nuclear-melt down materials to aid decommissioning and nuclear fuel management at nuclear accident sites.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

A Quantum Analog Coprocessor for Correlated Electron Systems Simulation

Analog quantum simulation is an approach for studying physical systems that might otherwise be computationally intractable to simulate on classical high-performance computing (HPC) systems. The key idea behind analog quantum simulation is the realization of a physical system with a low-energy effective Hamiltonian that is the same as the low-energy effective Hamiltonian of some target system to be studied. Purpose-built nanoelectronic devices are a natural candidate for implementing the analog quantum simulation of strongly correlated materials that are otherwise challenging to study using classical HPC systems. However, realizing devices that are sufficiently large to study the properties of a non-trivial material system (e.g., those described by a Fermi-Hubbard model) will eventually require the fabrication, control, and measurement of at least 0(10) quantum dots, or other engineered quantum impurities. As a step toward large-scale analog or digital quantum simulation platforms based on nanoelectronic devices, we propose a new approach to analog quantum simulation that makes use of the large Hilbert space dimension of the electronic baths that are used to adjust the occupancy of one or a few engineered quantum impurities. This approach to analog quantum simulation allows us to study a wide array of quantum impurity models. We can further augment the computational power of such an approach by combining it with a classical computer to facilitate dynamical mean-field theory (DMFT) calculations. DMFT replaces the solution of a lattice impurity problem with the solution of a family of localized impurity problems with bath couplings that are adjusted to satisfy a self-consistency condition between the two models. In DMFT, the computationally challenging task is the high-accuracy solution of an instance of a quantum impurity model that is determined self-consistently in coordination with a mean-field calculation. We propose using one or a few engineered quantum impurities with adjustable couplings to baths to realize an analog quantum coprocessor that effects the solution of such a model through measurements of a physical quantum impurity, operating in coordination with a classical computer to achieve a self-consistent solution to a DMFT calculation. We focus on implementation details relevant to a number of technologies for which Sandia has design, fabrication, and measurement expertise. The primary technical advances outlined in this report concern the development of a supporting modeling capability. As with all analog quantum simulation platforms, the successful design and operation of individual devices depends critically on one's ability to predict the effective low-energy Hamiltonian governing its dynamics Our project has made this possible and lays the foundation for future experimental implementations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Summary of Structural Material Modeling Development for the NEAMS Program in Fiscal Year 2020

This report summarizes work performed during Fiscal Year (FY) 2020 at Idaho National Laboratory (INL) for the U.S. Department of Energy?s Nuclear Engineering Advanced Modeling and Simulation (NEAMS) program for the Structural Materials and Chemistry Technical Area in the work package entitled "MS- 20IN050104 - Structural Materials - INL." The Structural Materials and Chemistry Technical Area is a relatively new component of the NEAMS program, and is currently focusing on developing simulation capabilities to support the deployment of nuclear energy in the areas of molten salt reactor chemistry, light water reactor (LWR) structural material degradation, and structural material behavior for advanced reactor applications. INL performed work for to advance capabilities for simulation of structural material behavior in both LWR and advanced reactor applications in the work described here.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

First-Principles Investigation of Electrides Derived from Sodalites

Recently, electride materials, with excess anionic electrons confined in their empty space, have received growing attention due to their promising applications in catalysis, nonlinear optics, and spin electronics. However, the utilization of electride materials is limited by their thermal instability. Here, we introduce an alternative way to achieve the localized anionic electron states via the removal of highly symmetric Wyckoff sites of anions from the existing sodalite compounds. Using four halide sodalites as the parental structures, our simulation reveals that the materials after the removal of anionic halide sites exhibit typical electride behaviors that are characterized by the existence of localized electronic states near the Fermi level. Compared to most previously studied electrides, these materials are expected to be more thermally stable due to the complex structural framework and thus promising for practical applications. Among them, Na 4 (AlSiO 4 ) 3 manifests magnetic electronic structure. We demonstrate that this magnetism originates from a highly localized excess electron state surrounded by electropositive alkaline cations. Here, our results suggest Na 4 (AlSiO 4 ) 3 could be a promising spintronics component, thus encouraging further experimental study.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Combined Computational and Mathematical Analysis of Interconnect Fatigue Potential in Photovoltaic Modules

A finite element model of a 60-cell monocrystalline silicon glass-polymer photovoltaic module was simulated with ±1.0 kPa and ±2.4 kPa loads applied to the glass to calculate the deformation under load. Cell-to-cell displacements were used to approximate interconnect strain and stress. A mathematical fatigue cycle life relation was fitted to data for the interconnect material (copper), to generate a life prediction at each interconnect location based on the local stress means, reversal extents, and amplitudes. Interconnect stress was found to be significantly asymmetric about zero despite symmetric positive and negative module loads due to laminate thickness offsets about the neutral plane and the effects of module framing. Cycle life results indicated that interconnect fatigue failure was unlikely to occur over a 30-year lifetime of conservative wind and snow load cycles since the typical cell design feature of leaving some unconstrained length between the cell edge and first solder pad increases the effective gauge length and decreases the stress levels below the material endurance limit. Follow-up analyses found that 3.6 mm and 6.4 mm were the minimum unconstrained lengths required to survive the assumed lifetime of wind and snow cycles, respectively, confirming that typical industrial module constructions with 8–15 mm unconstrained lengths should survive conservatively. Notably, large magnitude, low-cycle snow loading was consistently the limiting factor requiring a longer unconstrained interconnect length. Finally, insights and workflows from this study inform module interconnection design limits for survival against mechanical fatigue in deployment environments.

14 SOLAR ENERGY↗
DOE OSTI2026

The high explosives & affected targets (HEAT) dataset

Artificial Intelligence (AI) surrogate models offer a computationally efficient alternative to full-physics simulations, yet no existing datasets are publicly available for training, testing, and validation of machine learning models of the dynamics of high-explosive driven shocks through multiple materials. Shock propagation through materials is a computationally challenging problem because simulations must include material-specific equations of state (EOS) along with descriptions of other physical processes such as plastic deformation, phase change, damage processes, fluid instabilities, and multi-material interactions. Shocks are typically initiated by high-velocity impacts or explosive loading. The latter case necessitates the addition of models of reactive materials to represent high-explosive (HE) detonation. Here, to address the lack of an expansive dataset for multi-material shock propagation in the AI/ML community, we present the High-Explosives and Affected Targets (HEAT) Dataset. HEAT is a physics-rich collection of two-dimensional, cylindrically symmetric, simulations generated using an Eulerian, multi-material, shock-propagation code developed at Los Alamos National Laboratory. The dataset includes two partitions: (1) the expanding shock-cylinder (CYL) simulations, Figs. 1, and (2) the Perturbed Layered Interface (PLI) simulations, Fig. 2. Entries in both partitions consist of time series of arrays of thermodynamic fields (pressure, density, and temperature), kinematic fields (position and velocity), and additional fields that depend on thermodynamic and/or kinematic fields (e.g., material stress). Materials in the CYL partition include solids (aluminium, copper, depleted uranium, stainless steel, tantalum, and a generic polymer), a liquid (water), gases (air, nitrogen), and a generic detonating material (high explosive, HE). The PLI partition spans a highly varying geometry but consists of fixed materials across entries: Copper, aluminium, stainless steel, generic polymer, and generic HE. HEAT captures critical phenomena such as momentum transfer, shock propagation, plastic deformation, and thermal effects, making HEAT a valuable benchmark for development of AI/ML emulation of multi-material shock propagation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Accelerating high-strain continuum-scale brittle fracture simulations with machine learning

Failure in brittle materials under dynamic loading conditions is a result of the propagation and coalescence of microcracks. Simulating this discrete crack evolution at the continuum level is computationally expensive or, in some cases, intractable, resulting in the need to make broad assumptions or neglect key physics. In this work, we have developed an approach using machine learning that overcomes the current inability to represent meso-scale physics at the macro-scale. Our approach leverages damage and stress data from a computationally expensive high-fidelity model that explicitly resolves microcrack behavior to build an inexpensive machine learning emulator. Once trained, the machine learning emulator is used to predict the evolution of crack length statistics, which then informs a continuum-scale constitutive model. This results in a significant speed-up of the workflow by four orders of magnitude. Both the machine learning emulator and the continuum-scale model are validated against the high-fidelity model and experimental data, respectively, showing excellent agreement. There are two key findings. The first is that we can reduce the dimensionality of the problem, establishing that the machine learning emulator only needs the length of the longest crack and one of the maximum stress components to capture the necessary physics. Another compelling finding is that the emulator can be trained in one experimental setting and transferred successfully to predict behavior in a different setting.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Machine learning for collective variable discovery and enhanced sampling in biomolecular simulation

Classical molecular dynamics simulates the time evolution of molecular systems through the phase space spanned by the positions and velocities of the constituent atoms. Molecular-level thermodynamic, kinetic, and structural data extracted from the resulting trajectories provide valuable information for the understanding, engineering, and design of biological and molecular materials. The cost of simulating many-body atomic systems makes simulations of large molecules prohibitively expensive, and the high-dimensionality of the resulting trajectories presents a challenge for analysis. Driven by advances in algorithms, hardware, and data availability, there has been a flare of interest in recent years in the applications of machine learning – especially deep learning – to molecular simulation. Furthermore, these techniques have demonstrated great power and flexibility in both extracting mechanistic understanding of the important nonlinear collective variables governing the dynamics of a molecular system, and in furnishing good low-dimensional system representations with which to perform enhanced sampling or develop long-timescale dynamical models. It is the purpose of this article to introduce the key machine learning approaches, describe how they are married with statistical mechanical theory into domain-specific tools, and detail applications of these approaches in understanding and accelerating biomolecular simulation.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2022

Artificial neural network approach for multiphase segmentation of battery electrode nano-CT images

The segmentation of tomographic images of the battery electrode is a crucial processing step, which will have an additional impact on the results of material characterization and electrochemical simulation. However, manually labeling X-ray CT images (XCT) is time-consuming, and these XCT images are generally difficult to segment with histographical methods. We propose a deep learning approach with an asymmetrical depth encode-decoder convolutional neural network (CNN) for real-world battery material datasets. This network achieves high accuracy while requiring small amounts of labeled data and predicts a volume of billions voxel within few minutes. While applying supervised machine learning for segmenting real-world data, the ground truth is often absent. The results of segmentation are usually qualitatively justified by visual judgement. We try to unravel this fuzzy definition of segmentation quality by identifying the uncertainty due to the human bias diluted in the training data. Further CNN trainings using synthetic data show quantitative impact of such uncertainty on the determination of material’s properties. Nano-XCT datasets of various battery materials have been successfully segmented by training this neural network from scratch. We will also show that applying the transfer learning, which consists of reusing a well-trained network, can improve the accuracy of a similar dataset.

25 ENERGY STORAGE↗
DOE OSTI2022

Extemporaneous Mechanochemistry: Shock-Wave-Induced Ultrafast Chemical Reactions Due to Intramolecular Strain Energy

We report regions of energy localization referred to as hotspots are known to govern shock initiation and the run-to-detonation in energetic materials. Mounting computational evidence points to accelerated chemistry in hotspots from large intramolecular strains induced via the interactions between the shock wave and microstructure. However, definite evidence mapping intramolecular strain to accelerated or altered chemical reactions has so far been elusive. From a large-scale reactive molecular dynamics simulation of the energetic material 1,3,5-triamino-2,4,6-trinitrobenzene, we map decomposition kinetics to molecular temperature and intramolecular strain energy prior to reaction. Both temperature and intramolecular strain are shown to accelerate chemical kinetics. A detailed analysis of the atomistic trajectory shows that intramolecular strain can induce a mechanochemical alteration of decomposition mechanisms. The results in this paper could inform continuum-level chemistry models to account for a wide range of mechanochemical effects.

36 MATERIALS SCIENCE↗