Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “lead optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Rocket propulsion by thermonuclear micro-bombs ignited with intense relativistic electron beams.

Discussion of a method for the ignition of a thermonuclear microbomb by means of an intense relativistic electron beam with regard to its potential application to rocket propulsion. With such a system, exhaust velocities up to 1000 km/sec, corresponding to a specific impulse of 100,000 sec, seem to be within the realm of possibility. The rocket is propelled by a chain of thermonuclear microbombs exploded in a concave magnetic mirror produced by superconducting field coils. The magnetic pressure of the field reflects the fireball generated by the explosion. For the large capacitor bank required to generate the intense relativistic electron beam, a desirable lightweight design may be possible through use of ferroelectric materials. Because of the high cost of the T-D and He 3-D thermonuclear material, the system has to be optimized by minimizing the T-D and He 3-D consumption by a proper TD and He 3-D fuel to hydrogen propellant mass ratio, leading to a larger total system mass than would be absolutely necessary.

Winterberg, F.↗
NASA NTRS1985

Stochastic response analysis, order reduction, and output feedback controllers for flexible spacecraft

Real disturbances and real sensors have finite bandwidths. The first objective of this paper is to incorporate this finiteness in the 'open-loop modal cost analysis' as applied to a flexible spacecraft. Analysis based on residue calculus shows that among other factors, significance of a mode depends on the power spectral density of disturbances and the response spectral density of sensors at the modal frequency. The second objective of this article is to compare performances of an optimal and a suboptimal output feedback controller, the latter based on 'minimum error excitation' of Kosut. Both the performances are found to be nearly the same, leading us to favor the latter technique because it entails only linear computations. Our final objective is to detect an instability due to truncated modes by representing them as a multiplicative and an additive perturbation in a nominal transfer function. In an example problem it is found that this procedure leads to a narrow range of permissible controller gains, and that it labels a wrong mode as a cause of instability. A free beam is used to illustrate the analysis in this work.

Hablani, H. B.↗
NASA NTRS1986

Design and evaluation of a failure detection and isolation algorithm for restructurable control systems

The use of a decentralized approach to failure detection and isolation for use in restructurable control systems is examined. This work has produced: (1) A method for evaluating fundamental limits to FDI performance; (2) Application using flight recorded data; (3) A working control element FDI system with maximal sensitivity to critical control element failures; (4) Extensive testing on realistic simulations; and (5) A detailed design methodology involving parameter optimization (with respect to model uncertainties) and sensitivity analyses. This project has concentrated on detection and isolation of generic control element failures since these failures frequently lead to emergency conditions and since knowledge of remaining control authority is essential for control system redesign. The failures are generic in the sense that no temporal failure signature information was assumed. Thus, various forms of functional failures are treated in a unified fashion. Such a treatment results in a robust FDI system (i.e., one that covers all failure modes) but sacrifices some performance when detailed failure signature information is known, useful, and employed properly. It was assumed throughout that all sensors are validated (i.e., contain only in-spec errors) and that only the first failure of a single control element needs to be detected and isolated. The FDI system which has been developed will handle a class of multiple failures.

Weiss, Jerold L.↗
NASA NTRS1993

Rover imaging system for the Mars rover/sample return mission

In the past year, the conceptual design of a panoramic imager for the Mars Environmental Survey (MESUR) Pathfinder was finished. A prototype camera was built and its performace in the laboratory was tested. The performance of this camera was excellent. Based on this work, we have recently proposed a small, lightweight, rugged, and highly capable Mars Surface Imager (MSI) instrument for the MESUR Pathfinder mission. A key aspect of our approach to optimization of the MSI design is that we treat image gathering, coding, and restoration as a whole, rather than as separate and independent tasks. Our approach leads to higher image quality, especially in the representation of fine detail with good contrast and clarity, without increasing either the complexity of the camera or the amount of data transmission. We have made significant progress over the past year in both the overall MSI system design and in the detailed design of the MSI optics. We have taken a simple panoramic camera and have upgraded it substantially to become a prototype of the MSI flight instrument. The most recent version of the camera utilizes miniature wide-angle optics that image directly onto a 3-color, 2096-element CCD line array. There are several data-taking modes, providing resolution as high as 0.3 mrad/pixel. Analysis tasks that were performed or that are underway with the test data from the prototype camera include the following: construction of 3-D models of imaged scenes from stereo data, first for controlled scenes and later for field scenes; and checks on geometric fidelity, including alignment errors, mast vibration, and oscillation in the drive system. We have outlined a number of tasks planned for Fiscal Year '93 in order to prepare us for submission of a flight instrument proposal for MESUR Pathfinder.

Source record↗
NASA NTRS1994

Effects of Spaceflight and Hindlimb Suspension on the Posture and Gait of Rats

Instability of posture and gait in astronauts following spaceflight (SF) is thought to result from muscle atrophy and from changes in sensory-motor integration in the CNS (central nervous system) that occur during adaptation to microgravity (micro-G). Individuals are thought to have developed, during SF, adaptive changes for the processing of proprioceptive, vestibular and visual sensory inputs with reduced weighting of gravity-based signals and increased weighting of visual and tactile cues. This sensory-motor rearrangement in the CNS apparently occurs to optimize neuromuscular system function for effective movement and postural control in micro-G. However, these adaptive changes are inappropriate for the 1 g environment and lead to disruptions in posture and gait on return to Earth. Few reports are available on the effects of SF on the motor behavior of animals. Rats studied following 18.5 - 19.5 days of SF in the COSMOS program were described as being ..'inert, apathetic, slow'.. and generally unstable. The hindlimbs of these rats were ..'thrust out from the body with fingers pulled apart and the shin unnaturally pronated'. On the 6th postflight day motor behavior was described as similar to that observed in preflight observations. Improved understanding of the mechanisms leading to these changes can be obtained in animal models through detailed analysis of neural and molecular mechanisms related to gait. To begin this process the posture and gait of rats were examined following exposure to either SF or hindlimb suspension (HLS), and during recovery from these conditions.

Fox, R. A.↗
NASA NTRS2005

Modeling Leadership Styles in Human-Robot Team Dynamics

The recent proliferation of robotic systems in our society has placed questions regarding interaction between humans and intelligent machines at the forefront of robotics research. In response, our research attempts to understand the context in which particular types of interaction optimize efficiency in tasks undertaken by human-robot teams. It is our conjecture that applying previous research results regarding leadership paradigms in human organizations will lead us to a greater understanding of the human-robot interaction space. In doing so, we adapt four leadership styles prevalent in human organizations to human-robot teams. By noting which leadership style is more appropriately suited to what situation, as given by previous research, a mapping is created between the adapted leadership styles and human-robot interaction scenarios-a mapping which will presumably maximize efficiency in task completion for a human-robot team. In this research we test this mapping with two adapted leadership styles: directive and transactional. For testing, we have taken a virtual 3D interface and integrated it with a genetic algorithm for use in &le-operation of a physical robot. By developing team efficiency metrics, we can determine whether this mapping indeed prescribes interaction styles that will maximize efficiency in the teleoperation of a robot.

Cruz, Gerardo E.↗
NASA NTRS2019

Exploring Human Factors Issues for Urban Air Mobility Operations

Urban air mobility (UAM) is currently receiving increased attention in the aviation literature as a new entrant into the airspace. Although the introduction of UAM offers the potential for significant benefits, it also creates the potential for fundamental change to the current air traffic management system. Several concepts are being explored to enable the development of a safe and efficient UAM system for near, mid and far term operations. A concept of operations for near term operations proposes several assumptions. Concepts for roles and responsibilities of human operators such as air traffic controllers propose different degrees of involvement. Identifying and exploring human factors issues is therefore a critical next step in the forward progression of concept development. A human-in-the-loop air traffic control simulation was used to investigate the effect of UAM traffic density and changes in current airspace routes and communication procedures on subjective controller workload and efficiency-related task performance. Findings indicate that although subjective workload was manageable for low density operations, medium and high density operations led to unmanageable levels of workload, leading to refusals to allow more vehicles into controlled airspace. By implementing a letter of agreement, verbal communications were reduced which were associated with reduced workload. Optimized routes were also associated with reduced workload and increased performance efficiency. Although these adjustments can positively support controller performance, workload still remained high during the high density UAM traffic scenarios. It is therefore suggested that, in order for UAM operation to become scalable, human operators will be required to work differently compared to current air traffic controllers. Future research should focus on the level and type of human operator or controller involvement and mated systems, to ensure safety and efficiency within UAM operations.

Air Traffic Management↗
NASA NTRSDate not supplied

Applying Sensor Uncertainty Mitigation Schemes to Detect-and-Avoid Systems

Impact of sensor noise on the performance of Detect-And-Avoid (DAA) systems can be reduced by implementing various mitigation schemes. This paper evaluates the Sensor Uncertainty Mitigation (SUM) method, implemented in the Detect and Avoid Alerting Logic for Unmanned Systems (DAIDALUS) algorithm, a reference implementation in the DAA minimum operational performance standards. DAIDALUS SUM performance is evaluated using a few safety and operational suitability metrics and compared with more traditional approaches using static safety buffers. A large number of encounters representative of low-speed unmanned aircraft against non-cooperative manned aircraft are simulated and evaluated. An air-to-air radar model produces representative sensor noise for the DAA system. Results show that increasing the tunable parameters for horizontal and vertical uncertainty in DAIDALUS SUM improves the safety metric at the cost of increasing the number of system alerts leading to increased workload. A range of SUM parameters is recommended as suitable values for the type of operations considered for this work. General trends and optimal SUM configurations were found to be nearly the same for two large and very different encounter data sets.

detect and avoid↗
NASA NTRS1985

An optimized top contact design for solar cell concentrators

A new grid optimization scheme is developed for point focus solar cell concentrators which employs a separated grid and busbar concept. Ideally, grid lines act as the primary current collectors and receive all of the current from the semiconductor region. Busbars are the secondary collectors which pick up current from the grids and carry it out of the active region of the solar cell. This separation of functions leads to a multithickness metallization design, where the busbars are made larger in cross section than the grids. This enables the busbars to carry more current per unit area of shading, which is advantageous under high solar concentration where large current densities are generated. Optimized grid patterns using this multilayer concept can provide a 1.6 to 20 percent increase in output power efficiency over optimized single thickness grids.

Desalvo, Gregory C.↗
NASA NTRS1995

Micromechanisms for optimism seismometer

Within the framework of the Mars 94 mission, it was decided to design and build a new vertical axis seismometer in order to continuously record the seismic events occurring on the Mars planet. The mission requirements lead to very stringent constraints on power, volume, mass and shock resistance at the landing. The seismometer must be capable of automatic leveling and automatic fitting to the local gravity. This paper deals with the mechanisms designed for this seismometer. Due to the short allotted time for its development and low cost, the baseline was to apply the rules of spatial tribology and, when it was possible, to customize existing components for space applications.

Paulin, Nicolas↗
NASA NTRS1994

Equivalent plate structural modeling for wing shape optimization including transverse shear

A new technique for structural modeling of airplanes wings is presented taking transverse shear effects into account. The kinematic assumptions of first-order shear deformation plate theory in combination with numerical analysis, where simple polynomials are used to define geometry, construction, and displacement approximations, lead to analytical expressions for elements of the stiffness and mass matrices and load vector. Contributions from the cover skins, spar and rib caps, and spar and rib webs are included as well as concentrated springs and concentrated masses. Limitations of wing modeling techniques based on classical plate theory are discussed, and the improved accuracy of the new equivalent plate technique is demonstrated through comparison with finite element analysis and test results. Expressions for analytical derivatives of stiffness, mass, and load terms with respect to wing shape are given. Based on these, it is possible to obtain analytic sensitivities of displacements, stresses, and natural frequencies with respect to planform shape and depth distribution. This makes the new capability an effective structural tool for wing shape optimization.

Livne, Eli↗
NASA NTRS1994

Equivalent Plate Structural Modeling for Wing Shape Optimization Including Transverse Shear

A new technique for structural modeling of airplane wings is presented taking transverse shear effects into account. The kinematic assumptions of first-order shear deformation plate theory In combination with numerical analysis, where simple polynomials are used to define geometry, construction, and displacement approximations, lead to analytical expressions for elements of the stiffness and mass matrices and load vector. Contributions from the cover skins, spar and rib caps, and spar and rib webs are included as well as concentrated springs and concentrated masses. Limitations of wing modeling techniques based on classical plate theory are discussed, and the Improved accuracy of the new equivalent plate technique is demonstrated through comparison with finite element analysis and test results. Expressions for analytical derivatives of stiffness, mass, and load terms with respect to wing shape are given. Based on these, it is possible to obtain analytic sensitivities of displacements, stresses, and natural frequencies with respect to planform shape and depth distribution. This makes the new capability an effective structural tool for wing shape optimization.

Livne, Eli↗
NASA NTRS1993

Trajectory optimization for the National Aerospace Plane

The objective of this second phase research is to investigate the optimal ascent trajectory for the National Aerospace Plane (NASP) from runway take-off to orbital insertion and address the unique problems associated with the hypersonic flight trajectory optimization. The trajectory optimization problem for an aerospace plane is a highly challenging problem because of the complexity involved. Previous work has been successful in obtaining sub-optimal trajectories by using energy-state approximation and time-scale decomposition techniques. But it is known that the energy-state approximation is not valid in certain portions of the trajectory. This research aims at employing full dynamics of the aerospace plane and emphasizing direct trajectory optimization methods. The major accomplishments of this research include the first-time development of an inverse dynamics approach in trajectory optimization which enables us to generate optimal trajectories for the aerospace plane efficiently and reliably, and general analytical solutions to constrained hypersonic trajectories that has wide application in trajectory optimization as well as in guidance and flight dynamics. Optimal trajectories in abort landing and ascent augmented with rocket propulsion and thrust vectoring control were also investigated. Motivated by this study, a new global trajectory optimization tool using continuous simulated annealing and a nonlinear predictive feedback guidance law have been under investigation and some promising results have been obtained, which may well lead to more significant development and application in the near future.

Lu, Ping↗
NASA NTRS1997

RNS Applications for Interacting Sub- and Supersonic Flows

A solution based grid adaptation method that combines elements of the multigrid method for solution acceleration and the domain decomposition philosophy for grid optimization is described. Unlike other solution based adaptive gridding schemes, wherein the overhead of recomputing the grid and re-evaluating the solution on the adapted grid leads to higher computational costs compared to a non-adapted calculation, the present methodology reduces the computational time required to obtain the solution. The computational effort involved in the present calculation is significantly lower than a non-adapted calculation that utilizes the multigrid method purely as a convergence acceleration tool. In addition to convergence acceleration, the multigrid framework provides a mechanism of information transfer from regions wherein grid refinement is specified to unrefined coarse grid regions. The basis for domain decomposition in the current procedure is the variation in grid refinement requirements for each coordinate direction in different portions of the flow field. The method is demonstrated herein on an efficient set of governing equations termed the reduced Navier Stokes equations, applied in conjunction with a set of physical boundary conditions. The governing equations are discretized through a pressure based flux splitting procedure that is uniformly applicable from incompressible to supersonic Mach numbers.

Rubin, Stanley G.↗
NASA NTRS1999

CEAS/AIAA/ICASE/NASA Langley International Forum on Aeroelasticity and Structural Dynamics 1999

These proceedings represent a collection of the latest advances in aeroelasticity and structural dynamics from the world community. Research in the areas of unsteady aerodynamics and aeroelasticity, structural modeling and optimization, active control and adaptive structures, landing dynamics, certification and qualification, and validation testing are highlighted in the collection of papers. The wide range of results will lead to advances in the prediction and control of the structural response of aircraft and spacecraft.

Woodrow Whitlow, Jr.↗
NASA NTRS1999

CEAS/AIAA/ICASE/NASA Langley International Forum on Aeroelasticity and Structural Dynamics 1999

The proceedings of a workshop sponsored by the Confederation of European Aerospace Societies (CEAS), the American Institute of Aeronautics and Astronautics (AIAA), the National Aeronautics and Space Administration (NASA), Washington, D.C., and the Institute for Computer Applications in Science and Engineering (ICASE), Hampton, Virginia, and held in Williamsburg, Virginia June 22-25, 1999 represent a collection of the latest advances in aeroelasticity and structural dynamics from the world community. Research in the areas of unsteady aerodynamics and aeroelasticity, structural modeling and optimization, active control and adaptive structures, landing dynamics, certification and qualification, and validation testing are highlighted in the collection of papers. The wide range of results will lead to advances in the prediction and control of the structural response of aircraft and spacecraft.

Woodrow Whitlow, Jr.↗
NASA NTRS1999

Developing a Fundamental Model for an Integrated GPS/INS State Estimation System with Kalman Filtering

This work will demonstrate the integration of sensor and system dynamic data and their appropriate models using an optimal filter to create a robust, adaptable, easily reconfigurable state (motion) estimation system. This state estimation system will clearly show the application of fundamental modeling and filtering techniques. These techniques are presented at a general, first principles level, that can easily be adapted to specific applications. An example of such an application is demonstrated through the development of an integrated GPS/INS navigation system. This system acquires both global position data and inertial body data, to provide optimal estimates of current position and attitude states. The optimal states are estimated using a Kalman filter. The state estimation system will include appropriate error models for the measurement hardware. The results of this work will lead to the development of a "black-box" state estimation system that supplies current motion information (position and attitude states) that can be used to carry out guidance and control strategies. This black-box state estimation system is developed independent of the vehicle dynamics and therefore is directly applicable to a variety of vehicles. Issues in system modeling and application of Kalman filtering techniques are investigated and presented. These issues include linearized models of equations of state, models of the measurement sensors, and appropriate application and parameter setting (tuning) of the Kalman filter. The general model and subsequent algorithm is developed in Matlab for numerical testing. The results of this system are demonstrated through application to data from the X-33 Michael's 9A8 mission and are presented in plots and simple animations.

Canfield, Stephen↗
NASA NTRS2002

An Atomistic Simulation of Crack Propagation in a Nickel Single Crystal

The main objective of this paper is to determine mechanisms of crack propagation in a nickel single crystal. Motivation for selecting nickel as a case study is because we believe that its physical properties are very close to that of nickel-base super alloy. We are directed in identifying some generic trends that would lead a single crystalline material to failure. We believe that the results obtained here would be of interest to the experimentalists in guiding them to a more optimized experimental strategy. The dynamic crack propagation experiments are very difficult to do. We are partially motivated to fill the gap by generating the simulation results in lieu of the experimental ones for the cases where experiment can not be done or when the data is not available.

Majid Karimi↗