SEARCH · Engineering Papers

Results for “interface resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

All sources NASA NTRS DOE OSTI

DOE OSTI2022

A Lyapunov-Based Generalized Dc-Side Controller Design for PV-Connected Systems

The objective of this paper is to realize a universal dc-side controller for photovoltaic (PV) systems where the control is agnostic to the downstream converter configuration. To achieve this, the downstream power converter and its controls are manipulated into an effective power control loop that is then cast into a generalized multi-loop design framework. On the dc side, a nonlinear small-signal model of the PV input is realized exclusively in terms of PV datasheet parameters (i.e., open-circuit voltage, short-circuit current, and maximum power point). Finally, a linear controller is used to modulate the dc-side PV system with the generic downstream power controller. A Lyapunov candidate is proposed to analyze the stability of the interconnected system and provide a streamlined approach for the controller design. The proposed design is validated on a 1k VA experimental setup that interfaces a PV module to the grid.

generalized PV controller↗

DOE OSTI2023

Exploiting Fixed Charge at Selective Contacts for Silicon Photovoltaics

The goal of this work was to examine and exploit fixed interface charges in ultra-thin (0-3 nm thickness) tunnel dielectric layers sandwiched between silicon and selective contact metal oxides (molybdenum oxide, MoO x , titanium oxide, TiO 2 ). Specifically, the interface fixed charge was varied by changing processing conditions and materials over a wide range and the effect on the current-voltage behavior and the Schottky barrier height was quantified. In budget period 1 (year 1), the objective was to grow aluminum oxide tunnel layers with quantified fixed charge over a range of ~1E12 to ~-2E12 cm -2 and combine these with MoO x and TiO 2 layers on Czochralsi (CZ) mono p- and n-Si, respectively. We sought conditions that maximize fixed charge and minimize Schottky barrier height to MoO x contacts to p-Si. This objective, along with investigating the effects of silicon surface terminations, occupied the majority of the project timeline (Q1-Q8) due to complications with high specific contact resistivity values. In the last two quarters of the project period, the objective was to insert HfO2 layers between Si and aluminum oxide layers to quench the fixed charge for layers with otherwise identical thermal history. Another objective was to lower the barrier height at TiO 2 -based contacts on n-type Si, but that was never investigated completely.

14 SOLAR ENERGY↗

DOE OSTI2023

Formulation and testing of a high-tin borosilicate nuclear waste glass for in-can melting

Here, borosilicate waste glasses were successfully developed to immobilize two high-level waste raffinate streams via an in-can melter process with an Inconel 601 canister at 1050 °C. Measured viscosity and crystallinity thermal profiles were within the targeted processing constraints for the in-can melter process. Measured chemical durability of the glass by ASTM C1285–21 (Method A), ranged from normalized loss of boron, NL(B) = 1.44 – 2.65 g•m -2 , and NL(B) decreased with increased waste loading, accompanied by increased SnO 2 crystallinity. Measured corrosion of the in-can melter canister by a glass melt showed that Inconel 601 performed well at 1100 °C for up to 500 hr. Resistance polarization measurements versus time revealed that Inconel 601 corrosion rates in (and by) glass melts decreased from an initial rate of 63 mm•y -1 down to 10.2 mm•y -1 after 137 h with increased duration, which was attributed to formation of an oxide passivation layer (mainly Cr 2 O 3 ) at the alloy-glass interface.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2025

Suppression of irradiation hardening in tungsten-coated ferritic steel for fusion reactor blanket applications

W-coated reduced activation ferritic steels have been developed for use as plasma facing components in fusion reactor blankets, offering excellent sputtering resistance and structural strength. Previous high-temperature coating methods, such as diffusion bonding and brazing, caused interfacial deterioration due to thermal stress from mismatched thermal expansion between W and reduced activation ferritic steel. To address this, underwater explosive welding was introduced as a high-velocity cold process that joins dissimilar materials while maintaining a strong, thin interface without the thermal issues associated with traditional methods. In this study, the effects of neutron irradiation on the hardness and microstructure in W-coated F82H reduced activation ferritic steel (W/F82H) joined by underwater explosive welding are investigated. Following neutron irradiation at 290 °C, irradiation hardening is suppressed in W, F82H, and their interface within the W/F82H material. Furthermore, microstructural observations indicate that the recovery of work hardening and relaxation of elastic strain introduced during coating significantly contribute to the suppression of irradiation hardening in W/F82H. In conclusion, W/F82H exhibits significantly suppressed irradiation hardening compared with those in stand-alone materials. This suppression is explained by residual stress from thermal expansion mismatch and the unique microstructure at the interface. These results provide valuable insights for the development of more durable materials in nuclear fusion applications.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Corrosion resistive materials, systems, and methods of forming and using the materials and systems

A method to reduce corrosion rates of materials at high temperatures may include heating a mixture and applying the heated mixture to a material to be rendered thermodynamically noble. The mixture may include carbon monoxide and carbon dioxide and the material rendered thermodynamically noble may include copper or other material having similar physical properties. The copper or other similar material may be applied to a structural material and provide a surface interfacing with the mixture of carbon monoxide and carbon dioxide to prevent corrosion of the structural material. In some cases, the structural material may form a heat exchanger defining passageways for a working fluid of a power system and/or may form other passageways of the power system. The copper may be applied to the passageways as a protective coating and then made thermodynamically noble at high temperatures after interactions with the mixture of carbon monoxide and carbon dioxide.

Anderson, Mark↗

DOE OSTI2023

Environmental barrier coatings on enhanced roughness SiC: Effect of plasma spraying conditions on properties and performance

Environmental barrier coatings for SiC/SiC composites are limited by the melting temperature of the Si bond coating near 1414°C. Systems without a bond coating may be required for future turbine applications where material temperatures go beyond 1350 °C. Here, enhanced roughness SiC substrates were developed to assess coating adhesion without the bond coating. Two EBCs with different YbMS/YbDS ratios were produced via modified plasma spraying parameters. Coating microstructure, thermal expansion, and modulus were measured for comparison of coating properties. Cyclic steam exposures at 1350°C were performed to assess oxidation resistance. The EBC with increased concentration of Yb 2 SiO 5 secondary phase displayed a higher CTE, which is typically expected to decrease adhesion lifetimes due to an increase in stress upon thermal cycling. Yet, the EBC chemistry with increased Yb 2 SiO 5 concentration was able to experience longer cycling times prior to coating delamination, likely due to interface interactions with the substrate and the thermally grown oxide.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Hybrid epoxy–acrylate resins for wavelength-selective multimaterial 3D printing

Structures in nature have evolved to combine hard and soft materials in precise 3D arrangements, which imbues bulk properties and functionality that remain elusive to mimic synthetically. However, the potential for biomimetic analogs to seamlessly interface hard materials with soft surfaces for applications ranging from robotics and sealants to medical devices (e.g., prosthetics and wearable health monitors) has driven the demand for innovative chemistries and manufacturing approaches. Herein, we unveil a liquid resin for rapid, high resolution digital light processing (DLP) 3D printing of multimaterial objects with an unprecedented combination of strength, elasticity, and resistance to aging. Two enabling discoveries are the use of a covalently bound (hybrid) epoxy-acrylate monomer that precludes plasticization of soft domains and a wavelength-selective photosensitizer that accelerates cationic curing for hard domains. Using dual projection for multicolor DLP 3D printing (UV and violet light), several bioinspired metamaterial structures are fabricated, including one with hard springs embedded in a soft cylinder to adjust compressive behavior and a detailed knee joint featuring “bones” and “ligaments” for smooth motion. Lastly, the application of this system to facilitate selective stretching for electronic devices is demonstrated with a proof-of-concept device.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Hydroxylation and Cation Segregation in (La 0.5 Sr 0.5 )FeO 3-$δ$ Electrodes

Simultaneously achieving high activity and stability is the primary challenge when engineering (electro)catalysts. Transition metal perovskite oxides are employed as air electrodes for solid-oxide fuel cells and electrolyzers. However, degradation of oxygen exchange kinetics at the solid–gas interface, often linked to alkaline-earth cation segregation and precipitation, limits widespread commercialization. Here, we systematically investigated the surface degradation mechanism induced by gas-phase impurities in La 0.5 Sr 0.5 )FeO 3-$δ$ (LSF55) thin-film electrodes by varying the concentration of H 2 O, SO 2 , and CO 2 . Degradation of the area-specific resistance in ambient and humidified synthetic air is significantly greater than in dry ambient and dry synthetic air, pointing to the importance of water vapor. Time-resolved, in situ ambient pressure X-ray photoelectron spectroscopy performed in O 2 showed that nonbulk Sr is present on the surface before the exposure to water vapor. Upon introduction of water vapor, neither additional Sr segregation nor precipitation driven by water vapor is a necessary condition for degradation. Rather, hydroxylation of the surface induces irreversible and significant degradation. At the same time, we show that Sr migration driven by water vapor is partially reversible. These fundamental insights can be used for the rational design of electrodes with improved catalytic stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

7.86 kV GaN-on-GaN PN power diode with BaTiO3 for electrical field management

Devices based on gallium nitride (GaN) have great potential for high power switching applications due to the high breakdown field and high electron mobility. In this work, we present a vertical GaN-on-GaN PN power diode using high dielectric constant material, BaTiO3, for electrical field management and high breakdown voltages, in together with an optimized guard-ring and field plate design. Numerical simulation shows that with high-k dielectrics implemented, the peak electrical field at the PN interface is mitigated from 3.5 to 3.1 MV/cm under a reverse bias of −9.05 kV. The device design with BaTiO3 shows a breakdown voltage of 9.65 kV or about 600 V improvement. The fabricated diodes with a 57 μm thick drift layer demonstrate a breakdown voltage of 7.86 kV on a bulk GaN substrate. The device has an on-resistance of 2.8 mΩ cm2 and a Baliga figure of merit of 22 GW/cm2.

Physics↗

DOE OSTI2025

Ferroelectric Al 1− x B x N sputtered thin films on n -type Si bottom electrodes

Ferroelectric Al 1−x B x N thin films are grown on highly doped and plasma treated (100) n-type Si. We demonstrate ferroelectricity for x = < 0.01, 0.02, 0.06, 0.08, 0.13, and 0.17 where the n-type Si is both the substrate and bottom electrode. Polarization hysteresis reveals remanent polarization values between 130 and 140 μC/cm 2 and coercive field values as low as 4 MV/cm at 1 Hz with low leakage. The highest resistivity and most saturating hysteresis occurs with B contents between x = 0.06 and 0.13. We also demonstrate the impact of substrate plasma treatment time on Al 1−x B x N crystallinity and switching. Cross-sectional transmission electron microscopy and electron energy loss spectra reveal an amorphous 3.5 nm SiN x layer at the Al 1−x B x N interface post-plasma treatment and deposition. The first ~ 5 nm of Al 1−x B x N is crystallographically defective. Using the n-type Si substrate, we demonstrate Al 1−x B x N thickness scaling to 25 nm via low-frequency hysteresis and CV. Serving as the bottom electrode and substrate, the n-type Si enables a streamlined growth process for Al 1−x B x N for a wide range of Al 1−x B x N compositions and layer thicknesses.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Scaling theory of three-dimensional magnetic reconnection spreading

We develop a first-principles scaling theory of the spreading of three-dimensional (3D) magnetic reconnection of finite extent in the out of plane direction. This theory addresses systems with or without an out of plane (guide) magnetic field, and with or without Hall physics. The theory reproduces known spreading speeds and directions with and without guide fields, unifying previous knowledge in a single theory. New results include: (1) Reconnection spreads in a particular direction if an x-line is induced at the interface between reconnecting and non-reconnecting regions, which is controlled by the out of plane gradient of the electric field in the outflow direction. (2) The spreading mechanism for anti-parallel collisionless reconnection is convection, as is known, but for guide field reconnection it is magnetic field bending. We confirm the theory using 3D two-fluid and resistive-magnetohydrodynamics simulations. (3) The theory explains why anti-parallel reconnection in resistive-magnetohydrodynamics does not spread. (4) The simulation domain aspect ratio, associated with the free magnetic energy, influences whether reconnection spreads or convects with a fixed x-line length. (5) We perform a simulation initiating anti-parallel collisionless reconnection with a pressure pulse instead of a magnetic perturbation, finding spreading is unchanged rather than spreading at the magnetosonic speed as previously suggested. The results provide a theoretical framework for understanding spreading beyond systems studied here, and are important for applications including two-ribbon solar flares and reconnection in Earth’s magnetosphere.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2022

Non-Equilibrium Doping of Poly-Si:Ga/SiOx Passivating Contacts Solar Cells

In this contribution, we show that Ga-hyperdoped poly-Si/SiOx contacts are realized by pulsed laser annealing and post-hydrogenation. The motivation behind this work is to improve the inferior performance of boron-doped poly- Si/SiOx contacts when compared to the phosphorus-doped contacts. Here we used Ga as a novel p-type dopant to replace B, as B is known to accumulate at the interface between the oxide and the crystalline silicon and cause recombination. Due to a high diffusivity of Ga in oxide and a much higher segregation coefficient (Si:SiOx), Ga is shown to be immune to the oxide pileup phenomenon. However, Ga has a low solid solubility limit in Si (5x10^19 cm-3), which is not enough to form a low resistivity contact. To overcome this problem, we explored pulsed laser annealing via excimer laser by varying the laser energy densities and pulses. The passivation and electrical properties are studied systematically using photoluminescence (PL), secondary ion mass spectrometry (SIMS), and Van der Pauw-Hall measurements. We show an active Ga doping concentration above 1x10^20 cm^-3, which is above the solid solubility limit of Ga in Si. Good passivation quality is demonstrated with the highest implied Voc (iVoc) of 721 mV on single side polished samples. Furthermore, a low diode contact resistivity of ~22 m..omega.. cm^2 is obtained using Ti/Ag contacts, with minimal metal-to-semiconductor contact resistivity of 0.9 m..omega.. cm^2.

non-equilibrium doping↗

DOE OSTI2022

On-Demand Designing of Cathode Internal Surface Architecture for Dramatic Enhancement of SOFC Performance and Durability

This project is aimed to design and modify the internal surfaces of porous composite cathode from currently commercially viable Solid Oxide Fuel Cells (SOFCs), using additive manufacturing process of Atomic Layer Deposition (ALD). The material systems being investigated are commercial composite electrodes complex three-dimensional topographies. In term of the chemistry of the ALD layer applied on the internal surface of the porous cathode, this project has employed commercially relevant electrolyte, electrocatalyst and noble metal materials set. Such materials are fully compatible with the commercial fuel cells, and this project has developed special nanostructure on the surface of the commercial composite cathodes. The formation of the designed nanoarchitecture on the surface of SOFC cathode has been achieved through precise control of ALD parameters and their effect on overall cell performance and resultant electrochemical reaction mechanism of cathodes has been investigated through full cell electrochemical performance testing and nanostructure characterization by transmission electron microscopy (TEM). Under the support of this award, following has been achieved: (1). For cathode materials in solid oxide fuel cells (SOFCs), such as perovskite mixed conductor La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-x (LSCF), cation surface segregation and consequently losing conductivity and active sites for the oxygen reduction reaction (ORR) are problematic. To mitigate the cation segregation and enhance SOFC durability, further decorating the internal backbone surface using the desired electrocatalysts could be a promoting approach. Commonly, the cation segregation such as Sr is very volatile, so the effective surface decoration is ideally conformal. Nevertheless, the conformal surface coating would inevitably alter the ORR pathways that initially take place on the surface of the backbone. To reveal the impact of the conformal coating on both the catalytic activity and the conductivity of the cathode, the unary electrocatalyst of Pt or CoO x , was applied to the LSCF/SDC composite electrode of inherently functional SOFCs, respectively. Both ALD coating layers evolve strong interaction with the LSCF composite cathode. Upon operations, the Pt coating layer remains conformal on LSCF grain surfaces but turns into discrete particles on SDC grain surfaces. Meanwhile, CoO x conformal coating grows to be the discrete nanograins on both the LSCF and SDC grains. ALD coating of the cathode alone reduces the ohmic resistance up to 28 % for the entire cells. The increased conductivity induced by the ALD coating of Pt or CoO x is ascribed to different mechanisms. For the inherent functional SOFCs, the present study presents a novel and feasible approach to apply a conformal, dense coating layer on the surface of a mixed conductor, simultaneously increasing the conductivity and durability of the SOFC cathode. (2). High resistance of the oxygen electrode still significantly hinders the state-of-the-art Solid Oxide Fuel Cells (SOFCs). In particular, for an oxygen electrode consisting of mixed electronic and ionic conductors, such as perovskite lanthanum strontium cobalt ferrite (LSCF), it deteriorates due to its low chemical stability of the grain surface. Such degradation is often associated with the segregation of cations. To prevent the cation surface segregation and its resultant perovskite phase decomposition, we demonstrate a conformal ultra-thin (7-10 nm) surface heterogeneous coating layer consisting of subjacent discrete Pt nanoparticles capped with a superjacent fully dense conformal CoO x layer. The performance studies indicate the ALD coating reduces the cell series resistance by up to 40 %. The conformal CoO x layer consists of randomly orientated but single-layered nanograins, with high-density intergranular and surface grain boundaries serving as the electrochemical reaction sites and facilitating mass transport. The conformal coating layer appears to have successfully suppressed the Sr outward diffusion and confined the Sr enriched layer to a ~ 2 nm interface perovskite phase between the coating layer and the LSCF grain surface. Moreover, this ultra-thin Sr enriched perovskite layer presumably possesses high oxygen vacancy and high ionic conductivity and further imposes tensile strain to the LSCF grain surfaces. With the combination of a conformal CoO x nanoionics, Sr enriched layer, and its strained interface, the ALD coating induced surface layer is estimated to have a conductivity of ~ 1.27x10 4 S/cm, which is over two orders magnitude of that from LSCF at 750 ºC.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2026

Single‐Step Recovery of Water from Stable Crude Oil‐Water Emulsion Using Surface Engineered Hybrid Inorganic‐Polymer Membranes

ABSTRACT Separating crude oil from water remains one of the most stubborn challenges in environmental remediation, especially for surfactant‐stabilized emulsions that resist conventional demulsification methods. Here, we report a scalable strategy for achieving near‐zero‐discharge separation of crude oil emulsions using a single superhydrophilic membrane. By applying low‐temperature atomic layer deposition (ALD) of various metal oxides onto activated polyvinylidene fluoride (PVDF) membranes, we create atomically precise surface‐engineered (SE) membranes that maintain an exceptionally strong hydration layer at the membrane‐feed interface, even at high oil loadings. Among the various metal oxides, TiO 2 ‐modified SE membranes exhibit superior interfacial water stability, enabling sustained dewatering of complex crude oil‐water emulsions with >98% separation efficiency and >97% water recovery, compared to only 24.6% water recovery for the pristine membrane. This separation performance surpasses conventional hydrophilic membranes and is comparable to complex Janus channel membrane systems, demonstrating near‐complete emulsion separation using a single membrane. This low‐temperature membrane surface engineering process with atomic‐level precision and potential for scalability via roll‐to‐roll fabrication is promising for industrial‐scale, energy‐efficient water treatment and oil spill remediation applications.

Sengupta, Bratin [Applied Materials Division Argon↗

DOE OSTI2025

Zwitterionic Photocurable Resin for High‐Resolution 3D Printing of Ultralow‐Fouling Microstructures

High‐resolution 3D printing technologies are enabling a new generation of microstructured materials for applications where biocompatibility is critical. However, most conventional 3D‐printable resins yield materials that exhibit trade‐offs between antifouling properties and mechanical robustness, limiting their applicability in living systems. In nature, zwitterionic surface groups form tightly bound hydration layers that act as effective barriers against protein and cell attachment. Inspired by this strategy, a zwitterionic acrylamide‐based photoresist—carboxybetaine di‐methacrylamide (CBDA)—is developed for projection‐based vat photopolymerization, enabling the fabrication of complex microarchitectures with exceptional antifouling properties. The bifunctional monomer allows the formation of dense, cross‐linked networks that resist swelling while maintaining a high density of zwitterionic groups. Printed structures exhibit strong resistance to protein and cell adhesion, as confirmed by porcine blood assays, alongside robust mechanical performance. As a demonstration, a tubular structure featuring a negative Poisson's ratio lattice is printed to showcase structural fidelity and versatility. This resin formulation offers a broadly applicable strategy for fabricating microscale devices and surfaces where antifouling performance and structural integrity are both essential—spanning biomedical interfaces, soft robotics, and beyond.

3D printing↗

DOE OSTI2022

Using θ' interfaces as templates for planar L1 2 precipitation in AlCuMnZr alloys

Controlled Mn and Zr additions to Al-Cu alloys have allowed for the improved retention of mechanical properties after extended 350°C exposures by stabilizing the main strengthening θ' (Al 2 Cu) phase. Ultimately, θ'/L1 2 (Al 3 Zr) co-precipitate formation stabilizes θ' most effectively; however, Zr diffuses sluggishly and has low solubility in aluminum castings. Increasing the Zr segregation rate would allow for faster and more effective θ'/L1 2 co-precipitation. It is demonstrated that the Zr segregation rate is faster when the Zr matrix content is higher. A much higher Zr matrix content was achieved by rapid cooling during additive manufacturing (AM) that produces θ'/L1 2 co-precipitation faster, which is shown by scanning transmission electron microscopy and atom probe tomography experiments. It was also found that Zr continuously segregates to θ' interfaces up to the most aggressive heat treatment studied such that planar L1 2 precipitates remain after the metastable θ' dissolves. In this manner, we demonstrate that θ' coherent interfaces serve as perfect templates to form stable planar L1 2 precipitates that can provide strength at higher temperatures than traditional θ' strengthened AlCu alloys. This work introduces an alloy design strategy that uses metastable precipitates to quickly nucleate and grow co-precipitates with a desired geometry that contain slow diffusing elements. These ideas can be applied to engineer more heat resistant alloys by taking advantage of high solute matrix contents enabled by rapid cooling during additive manufacturing.

36 MATERIALS SCIENCE↗

DOE OSTI2022

GROWdb US River Systems - Samples

GROW Overview We developed the Genome Resolved Open Watersheds database (GROWdb), which aims to increase genomic sampling and understanding of global river microbiomes. An emphasis of GROWdb is to create a publicly available and ever-expanding microbial genome database that is focused on rivers while being interoperable with databases from other ecosystems. GROWdb is based on a network-of-networks approach to move beyond a small collection of well-studied rivers, towards a spatially distributed, global network of systematic observations. GROWdb represents the first microbial, river-focused resource parsed at various scales from genes to MAGs to community level including expression and potential based measurements that will be of interest to microbiologists, ecologists, geochemists, hydrologists, and modelers. Dataset Acknowledgement GROWdb contains data from various research campaigns, please acknowledge the following data generators, as appropriate: WHONDRS derived genomes or samples - include this statement in your acknowledgements: “This study used data from the Worldwide Hydrobiogeochemistry Observation Network for Dynamic River Systems (WHONDRS) under the River Corridor Science Focus Area (SFA) at the Pacific Northwest National Laboratory (PNNL) that was generated at the U.S. Department of Energy (DOE) Joint Genome Institute User Facility. PNNL is operated by Battelle Memorial Institute for the U.S. DOE under Contract No. DE-AC05-76RL01830. The SFA is supported by the U.S. DOE, Office of Biological and Environmental Research (BER), Environmental System Science (ESS) Program.” Total Samples loaded onto this Narrative: 178 Note: Not all GROW samples may be loaded into KBase Data Availability The data underlying GROWdb are accessible across various platforms to ensure all levels of data structure are widely available. First, all reads and MAGs are publicly hosted on National Center for Biotechnology (NCBI) under Bioproject PRJNA946291. Second, all data related data presented here including MAG annotations, extended data tables, phylogenetic tree files, antibiotic resistance gene database files, and MAG abundance tables are available in Zenodo (link). Beyond the flat database files listed above, our aim for GROWdb was to maximize data use by making the data available in searchable and interactive platforms including the National Microbiome Data Collaborative (NMDC) data portal, the Department of Energy’s Systems Biology Knowledgebase (KBase), and a GROW specific user interface released here, GROWdb Explorer. Each platform provides different ways to interact with GROWdb: NMDC GROWdb formed a pilot project for the NMDC. Specifically, individual GROWdb datasets (metagenomes, metatranscriptomes, etc) are easily accessible and searchable through the NMDC data portal, where they are systematically connected to each other and to a rich suite of sample information and standard analysis results, following Findable, Accessible, Interoperable, and Reusable (FAIR) data practices. KBase GROWdb is publicly available within KBase, including samples (this Narrative), MAGs, and corresponding genome scale metabolic models. Access within KBase allows for immediate access and reuse of data, including comparison to private data using KBase’s 500+ analysis tools. Other linked narratives in KBase: GROW Metagenome Assembled Genomes (MAGs) GROW Metabolic Models GROWdb Explorer GROWdb data is also explorable through a graphical user interface built through the Colorado State University Geospatial Centroid (https://geocentroid.shinyapps.io/GROWdatabase/), allowing users to search and graph microbial and spatial data simultaneously. In summary, this microbial genome resource represents the first publicly available genome collection from rivers and offers data that can be leveraged across microbiome studies. GROWdb is an expanding repository to incorporate and unify global river multi-omic data for the future.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2023

Emergent quasi-two-dimensional metallic state derived from the Mott-insulator framework

Recent quasi-two-dimensional (quasi-2D) systems with judicious exploitation of the atomic monolayer or few-layer architecture exhibit unprecedented physical properties that challenge the conventional wisdom on condensed matter physics. Here we show that the infinite layer SrCuO 2 (SCO), a topical cuprate Mott insulator in bulk form, can manifest an unexpected metallic state in the quasi-2D limit when SCO is grown on TiO 2 -terminated SrTiO 3 (STO) substrates. The sheet resistance does not conform to Landau's Fermi liquid paradigm. Hard x-ray core-level photoemission spectra demonstrate a definitive Fermi level that resembles the hole doped metal. Soft x-ray absorption spectroscopy also reveals features analogous to those of a hole doped Mott insulator. Based on these results, we conclude that the hole doping does not occur at the interfaces between SCO and STO; instead, it comes from the transient layers between the chain-type and the planar-type structures within the SCO slab. In conclusion, the present work reveals a metallic state in the infinite layer SCO and invites further examination to elucidate the spatial extent of this state.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗