Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “impurity concentration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Maximum and Comparative Efficiency Calculations for Integrated Capture and Electrochemical Conversion of CO 2

CO 2 as a C1 feedstock is receiving increasing attention, but it typically exists in dilute or impure streams. The capture and conversion of CO 2 to fuels or chemicals using carbon-neutral energy mitigates carbon emissions when CO 2 is captured from point sources and results in net or negative carbon emissions when CO 2 is obtained by direct air capture. Additionally, CO 2 capture and conversion steps are typically viewed as separate processes that optimize either capture and concentration or catalytic conversions of pure streams of CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1974

Aircraft observations of Venus' near-infrared reflection spectrum - Implications for cloud composition

A comparison of aircraft-based measurement data on Venus' near-infrared (1.2- to 4.1-micron) reflection spectrum with computer generated spectra of a number of cloud candidates shows a 75-% or more concentrated water solution of sulfuric acid to give the only acceptable match to the profile of Venus' strong 3-micron absorption feature. However, the measurement data obtained also show a modest decline in reflectivity from 2.3-micron to 1.2-micron wavelength, which is inconsistent with the flat spectrum of sulfuric acid in this spectral region. It is hypothesized that this decline is due to impurities in the sulfuric acid droplets.

Pollack, J. B.↗
NASA NTRS1975

Effects of high doping levels on silicon solar cell performance

Open-circuit voltages measured in silicon solar cells made from 0.01 ohm-cm material are 150 mV lower than voltages calculated from simple diffusion theory and cannot be explained by poor diffusion lengths or surface leakage currents. An analytical study was made to determine whether high doping effects, which increase the intrinsic carrier concentration, could account for the low observed voltages and to determine the limits on voltage and efficiency imposed by high doping effects. The results indicate that the observed variation of voltage with base resistivity is predicted by these effects. A maximum efficiency of 19% (AMO) and a voltage of 0.7 volts were calculated for 0.1 ohm-cm cells assuming an optimum diffused layer impurity profile.

Godlewski, M. P.↗
NASA NTRS2024

Morphology and Luminescence Properties of Transition Metal Doped Zinc Selenide Crystals

Zinc selenide is an excellent matrix material to dope with rare-earth and transition metal to achieve mid-infrared luminescence to develop high power lasers. The luminescence, morphology and refractive index is significantly affected by the doping and defects generated due to size and valency of dopants, concentration, growth process and convection during the growth. The aim of the study is to investigate effect of point and line defects generated due to low doping of iron and chromium on the emission and morphology of the zinc selenide. Luminescence and morphological properties of large iron and chromium doped zinc selenide single crystals were studied to evaluate the effect of extremely low residual impurities and defects associated with the doping process. The emission properties following both short wavelength (i.e., ultraviolet; 350 – 370 nm) excitation and longer wavelength (i.e., near infrared; 850 – 870 nm) excitation were characterized. Luminescence emission bands were identified in both doped crystals. In addition to the primary emission bands, satellite peaks and intra-center transitions were also observed. Due to local population defects associated with the residual impurities (ppm to ppb) in the Fe-ZnSe and Cr-ZnSe crystals, peak emission wavelengths were observed to shift. Raman studies using 266 and 532 – nm excitation revealed different positions of longitudinal and transverse peaks for Fe-ZnSe and Cr-ZnSe crystals, associated with different levels of defects due to the different ion sizes. The emission bands were found to decrease in intensity due to recombination of residual impurity co-dopants and complex defects generated during growth and fabrication. Cryogenic temperature analyses revealed a very clean emission band due to freezing of some of the point and line defects. An emission band observed at 980 nm for both crystals at room temperature as well as cryogenic temperatures indicates a vibronic peak in ZnSe. The scanning electron microscopy (SEM) images of the local morphology support the conclusion that small crystallites in doped crystals are also present.

Zinc selenide↗
NASA NTRS1985

Surface Tensions and Their Variations with Temperature and Impurities

The surface tensions in this work were determined using the sessile drop technique. This method is based on a comparison of the profile of a liquid drop with the profile calculated by solving the Young-Laplace equation. The comparison can be made in several ways; the traditional Bashforth-Adams procedure was used in conjunction with recently calculated drop shape tables which virtually eliminate interpolation errors. Although previous study has found little difference in measurements with pure and oxygen doped silicon, there is other evidence suggesting that oxygen in dilute concentrations severely depresses the surface tension of silicon. The surface tension of liquid silicon in purified argon atmospheres was measured. A temperature coefficient near -0.28 mJ/square meters K was found. The experiments show a high sensitivity of the surface tension to what is believed are low concentrations of oxygen. Thus one cannot rule out some effect of low levels of oxygen in the results. However, the highest surface tension values obtained in conditions which minimized the residual oxygen pressure are in good agreement with a previous measurement in pure hydrogen. Therefore, depression of the surface tension by oxygen is insignificant in these measurements.

Hardy, S. C.↗
DOE OSTI2024

An Assessment of the Safeguards Implications of Particle and Alloy Formation in MSRs

Molten salt reactors (MSRs) present unique challenges for applying safeguards measures and differ significantly from traditional nuclear reactors. Although the special fissionable materials within MSRs principally exist as dissolved species within the fuel salt, key actinides of interest may also be converted to solid phases including alloys and precipitated oxides via chemical and electrochemical reactions. These solid-phase components will complicate the nuclear material accounting and control (NMAC) approaches that have, so far, primarily targeted measurements of the liquid salt itself. For example, most of the proposed monitoring and characterization methods for MSRs are reliant on homogeneity of the salt and the ability to maintain accountable materials in solution. Solid deposits and particulates could invalidate the assumption of homogeneity and necessitate the use of new models and measurement tools to permit a full accounting of all nuclear material in an MSR. To address this, the likelihood of solids formation in MSRs, estimated the rate at which these solids could form, and assessed the monitoring tools that are available to account for the presence of these materials were examined. Specifically, three solid forming mechanisms were investigated, including (1) the accumulation of actinides within the MSR’s structural materials due to alloying, (2) the accumulation of actinides within noble metal fission product particulates, and (3) the generation of actinide oxides from interactions with salt impurities. These modeling-informed studies were completed with considerations to both fluoride- and chloride-containing salts. It was determined that, although measurable amounts of special fissionable material were expected to alloy with the structural elements and fission products, the predicted amounts were below levels considered as significant quantities (SQ) by the International Atomic Energy Agency (IAEA). However, it was determined that sufficiently large oxygen concentrations could potentially lead to significant quantities of special fissionable material being converted to solid oxide phases. As such, a comparative study of technologies that are commercially available to assist in monitoring and accountancy of this material was presented. Policy implications, design recommendations, and suggestions for follow-on experimental work were also presented to further assist reactor vendors in designing and controlling the fuel salt chemistry to address potential safeguards considerations.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Quantifying Leaf Chlorophyll Concentration of Sorghum from Hyperspectral Data Using Derivative Calculus and Machine Learning

Leaf chlorophyll concentration (LCC) is an important indicator of plant health, vigor, physiological status, productivity, and nutrient deficiencies. Hyperspectral spectroscopy at leaf level has been widely used to estimate LCC accurately and non-destructively. This study utilized leaf-level hyperspectral data with derivative calculus and machine learning to estimate LCC of sorghum. We calculated fractional derivative (FD) orders starting from 0.2 to 2.0 with 0.2 order increments. Additionally, 43 common vegetation indices (VIs) were calculated from leaf spectral reflectance factor to make comparisons with reflectance-based data. Within the modeling pipeline, three feature selection methods were assessed: Pearson’s correlation coefficient (PCC), partial least squares based variable importance in the projection (VIP), and random forest-based mean decrease impurity (MDI). Finally, we used partial least squares regression (PLSR), random forest regression (RFR), support vector regression (SVR), and extreme learning regression (ELR) to estimate the LCC of sorghum. Results showed that: (1) increasing derivative order can show improved model performance until certain order for reflectance-based analysis; however, it is inconclusive to state that a particular order is optimal for estimating LCC of sorghum; (2) VI-based modeling outperformed derivative augmented reflectance factor-based modeling; (3) mean decrease impurity was found effective in selecting sensitive features from large feature space (reflectance-based analysis), whereas simple Pearson’s correlation coefficient worked better with smaller feature space (VI-based analysis); and (4) SVR outperformed all other models within reflectance-based analysis; alternatively, ELR with VIs from original reflectance yielded slightly better results compared to all other models.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

The impact of interfacial Si contamination on GaN-on-GaN regrowth for high power vertical devices

The development of gallium nitride (GaN) power devices requires a reliable selective-area doping process, which is difficult to achieve because of ongoing challenges associated with the required etch-then-regrow process. The presence of silicon (Si) impurities of unclear physical origin at the GaN regrowth interface has proven to be a major bottleneck. Furthermore, this paper investigates the origin of Si contamination at the epitaxial GaN-on-GaN interface and demonstrates an approach that markedly reduces its impact on device performance. An optimized dry-etching approach combined with UV-ozone and chemical etching is shown to greatly reduce the Si concentration levels at the regrowth interface, and a significant improvement in a reverse leakage current in vertical GaN-based p–n diodes is achieved.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Comparison of AlF 3 thin films grown by thermal and plasma enhanced atomic layer deposition

Films of aluminum fluoride (AlF 3 ) deposited by thermal and plasma enhanced atomic layer deposition (PEALD) have been compared using in situ multiwavelength ellipsometry (MWE) and monochromatic x-ray photoelectron spectroscopy (XPS). The AlF 3 films were grown using cyclic exposures of trimethylaluminum, hydrogen fluoride, and H radicals from a remote H 2 inductively coupled plasma. Films were characterized in situ using MWE and XPS for growth rate, film composition, and impurity incorporation. The MWE showed a growth rate of 1.1 and 0.7 Å per cycle, at 100 °C, for thermal and plasma enhanced ALD AlF 3 films, respectively. Carbon incorporation was below the XPS detection limit. The plasma enhanced ALD AlF 3 film showed the presence of Al-Al chemical states, in the Al 2p scans, suggesting the presence of Al-rich clusters with a concentration of 14%. The Al-rich clusters are thought to originate during the hydrogen plasma step of the PEALD process. Finally, the Al-rich clusters were not detected in thermal ALD AlF 3 films using the same precursors and substrate temperature.

36 MATERIALS SCIENCE↗
NASA NTRS1981

The properties of polycrystalline silicon solar cells with controlled titanium additions

By coupling the results of electrical measurements, such as spectral response, lighted and dark I-V determinations, and deep-level-transient spectroscopy with optical and laser scan photomicroscopy, the effects of grain boundaries and impurities on silicon solar cells were evaluated. Titanium, which produces two deep levels in silicon, degrades cell performance by reducing bulk lifetime and thus cell short-circuit current. Electrically active grain boundaries induce carrier recombination in the bulk and depletion regions of the solar cell. Experimental data imply a small but measurable segregation of titanium into some grain boundaries of the polycrystalline silicon containing high Ti concentration. However, for the titanium-contaminated polycrystalline material used in this study, solar cell performance is dominated by the electrically active titanium concentration in the grains. Microstructural impacts on the devices are of secondary importance

Rohatgi, A.↗
NASA NTRS1994

An investigation of the effect of surface impurities on the adsorption kinetics of hydrogen chemisorbed onto iron

The goal of this program has been to develop an understanding of heterogeneous kinetic processes for those molecular species which produce gaseous hydrogen degradation of the mechanical properties of metallic structural materials. During the present program, the interaction of hydrogen with the surfaces of alpha-2 (Ti3Al) titanium aluminide, gamma (TiAl) titanium aluminide, and beryllium were studied. The interaction of low pressure hydrogen with gamma titanium aluminide and beryllium was found to be relatively weak. Weak in the sense that adsorption leads to a low surface concentration of dissociated hydrogen, i.e., the chemisorption process is reversible at room temperature (300 K) for gamma titanium aluminide and the sticking coefficient for chemisorption is extremely small for beryllium. Hydrogen was found to interact readily with alpha-2 titanium aluminide to form a stable surface hydride at 300 K. These results correlate well with other recent studies which show that the mechanical properties for alpha-2 titanium aluminide are readily degraded in hydrogen while gamma titanium aluminide exhibits less degradation and beryllium essentially no degradation. The interaction of oxygen with the surface of several of these materials was studied. More recently, preliminary hydrogen permeation studies were completed for three high temperature alloys, Incoloy 909, Mo-47.5Re (wt. %), and this past year, Haynes 188.

Shanabarger, Mickey R.↗
DOE OSTI2024

Enhancing MnBi 2 Te 4 Stability by Doping

MnBi 2 Te 4 (MBT) is an intrinsically magnetic topological material that possesses unique properties due to the quantum Hall effect. However, the low Mn–Bi mixed antisite formation energy is detrimental to these properties as it alters the long-range magnetic ordering in the Mn layer. Therefore, it is crucial to destabilize the antisite defects in MBT while preserving the favorable electronic properties. Here, to this end, we utilized a screening approach to understand the role of dopants in the Mn and Bi sites. We find that Sc, Y, and La dopings prefer substitutions on the Bi site and significantly increase the Mn–Bi antisite defect formation energy. We find that the contribution from the empty s and d states of Sc, Y, and La around the Fermi level is insignificant. However, at the high concentration limit, the Bi–Te octahedra are significantly modified with doping, leading to important changes in the band structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

First-principles ionized-impurity scattering and charge transport in doped materials

Scattering of carriers with ionized impurities governs charge transport in doped semiconductors. However, electron interactions with ionized impurities cannot be fully described with quantitative first-principles calculations, so their understanding relies primarily on simplified models. Here we show an ab initio approach to compute the interactions between electrons and ionized impurities or other charged defects. It includes the short- and long-range electron-defect (e-d) interactions on equal footing and allows for efficient interpolation of the e-d matrix elements. Here we combine the e-d and electron-phonon interactions in the Boltzmann transport equation to compute the carrier mobilities in doped silicon over a wide range of temperature and doping concentrations, seamlessly spanning the defect- and phonon-limited transport regimes. The individual contributions of the defect- and phonon-scattering mechanisms to the carrier relaxation times and mean-free paths are analyzed. Our method provides a powerful tool to study electronic interactions in doped materials. It broadens the scope of first-principles transport calculations, enabling studies of a wide range of doped semiconductors and oxides with application to electronics, energy, and quantum technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Upcycling of Mixed Aluminum Alloy Shredder Scrap using Shear Processing

Conservation of critical materials is an increasing area of focus in the Unites States. In 2023, aluminum was added to the US Department of Energy Final Critical Materials List which has spurred public and private research into sustainable management of these resources. Additionally, efficiency in manufacturing and conservation of natural resources are growing concerns with targets to lower global carbon emissions, as primary aluminum alloy production is energy intensive, requiring 14 MWh of electricity plus 0.4 tonnes of CO2 per tonne of Al. Due to these factors, is essential that more sustainable manufacturing methods for aluminum alloys are developed going forward. To this end, much research is ongoing on the topic of more efficient utilization and recovery. However, most of this research still requires primary aluminum in the production process. Here, it will be attempted to bypass the use of primary aluminum and produce useful material recycled from 100% post-consumer scrap. Even considering recent developments in recycling of Al scrap, there is still a large amount of post-consumer scrap that is underutilized due to high impurity content, and that amount will increase significantly as more and more aluminum alloys are utilized in vehicles. This “scrap wave” is expected to cover 80% of the demand for automotive aluminum alloys by 2050 . A challenge to be addressed before the coming scrap wave can be fully utilized is that the tolerance of manufacturing techniques to impurities or off-spec alloy compositions must be increased. Particularly, in 5000-and 6000-series alloys (the most common wrought alloys in durable products), excess iron, copper, and silicon create brittle intermetallics during casting that remain in the extruded microstructure which limit the formability, ductility, and corrosion resistance of the alloy. Concerningly, many of the highest-volume post-consumer aluminum scrap streams such as automotive shredder scrap contain a mix of alloys including both wrought and cast alloys. Their compositions can vary widely depending on geography and the time of year. Because they are mixed, they often contain high content of multiple alloying elements such as Si and Cu in higher concentrations than are found in typical wrought alloys. They may also be contaminated with non-Al alloys from fasteners that get mixed in and often have high content of unwanted elements such as Fe. As a method for utilizing these underused scrap streams that are high in tramp elements, an emerging extrusion technology is being developed at the Pacific Northwest National Laboratory (PNNL) that aims to upcycle 100% post-consumer aluminum scrap directly into extruded components without the addition of primary aluminum . This new technology, called Shear Assisted Processing and Extrusion (ShAPE), is enabling a shift away from today’s recycling paradigm by reaching deeper into lower-value scrap streams, using shredder scrap as the extrusion billet material. Sometimes referred to as Twitch or Tweak, these scrap streams result from shredding and sorting of automobiles, building materials, appliances, and consumer goods. ShAPE combines the linear axis of conventional extrusion with a rotating extrusion die. This rotating die applies large strain to the material during extrusion, which breaks up large impurity-containing intermetallic particles, reducing their deleterious effects. This has been demonstrated for 6063 machining scrap spiked with excess Fe, and Twitch scrap high in Fe, Si and Cu where strength and ductility were retained for both feedstock compositions. Additionally, the extreme plastic deformation during ShAPE enables extrusion of billets with high Si that are too brittle for processing by conventional extrusion. By using 100% post-consumer shedder scrap as feedstock, ShAPE has the potential to slash embodied energy and carbon in extruded components by >80% compared to conventional extrusion of primary aluminum alloys.

Milligan, Brian K.↗
DOE OSTI2023

Analysis of degradation products in thermally treated TATB

Delineating the chemical composition of TATB (1,3,5-triamino-2,4,6-trinitrobenzene) residues produced from the exposure to abnormal thermal environments should lead to a better understanding of the decomposition paths. Identifying and quantifying each compound in thermally produced residues, monitors which compounds are degrading or forming along the decomposition route, as well as providing input for the kinetic models of those pathways. Here, in this paper, we report the methodology of isolating, identifying, and where possible, quantifying soluble compounds present in solid residues of thermally treated TATB (330 °C for tens of minutes). Samples were extracted with DMSO, separated using chromatography, and quantified using their absorption at 354 nm. Identification of unknown compounds was accomplished using high resolution mass spectrometry. TATB, F1 (diamino-dinitro-benzofurazan), HO-TATB (2,4,6-triamino-1-hydroxyl-3,5-dinitrobenzene), and T4A (1-chloro-3,5-dinitro-2,4,6-triaminobenzene) were trace compounds detected in the unreacted TATB. Ten more compounds that formed in the residues were structurally identified including F2 (amino-nitro-difurazan). Several more compounds were observed but not completely identified. We propose possible structures for the unknowns. Of the compounds formed, F1 was the most abundant compound reaching 4.5 % by weight of the degraded solid sample. Other degradation compounds were estimated to sum to trace levels, well below 1 %. Most compounds were new, having not been detected and identified in previous studies of production grade and thermally aged TATB. Many compounds only reached detectable concentrations after several min of thermal exposure.

36 MATERIALS SCIENCE↗
NASA NTRS1975

Studies of silicon PN junction solar cells

Silicon pn junction solar cells made with low-resistivity substrates show poorer performance than traditional theory predicts. The purpose of this research was to identify and characterize the physical mechanisms responsible for the discrepancy. Attention was concentrated on the open circuit voltage in shallow junction cells of 0.1 ohm-cm substrate resistivity. A number of possible mechanisms that can occur in silicon devices were considered. Two mechanisms which are likely to be of main importance in explaining the observed low values of open-circuit voltage were found: (1) recombination losses associated with defects introduced during junction formation, and (2) inhomogeneity of defects and impurities across the area of the cell. To explore these theoretical anticipations, various diode test structures were designed and fabricated and measurement configurations for characterizing the defect properties and the areal inhomogeneity were constructed.

Lindholm, F. A.↗
NASA NTRS2015

Evaluation of Volatile Species in Green Monopropellant Project

NASA is interested in green monopropellants to replace hydrazine in reaction control systems (RCSs). Some current NASA programs require reduced vapor pressure and low toxicity monopropellant (green) and superior performance (specific impulse and density) formulations. Earlier vapor phase studies of a candidate green monopropellant at the NASA White Sands Test Facility (WSTF) showed the presence of a volatile species that warranted further investigation. The purpose of this study was to further characterize the volatile species and to evaluate it. The evaluation was with respect to whether the volatile species was an impurity or how it is formed, and to use that information to examine whether its presence as an impurity can be eliminated during formulation. The evaluation also considered whether formation of the volatile impurity could be prevented while not compromising the propellant. To reduce variables associated with evaluation of the propellant formulation as a whole, a precursor to one of the individual components in the propellant formulation was subjected to a NASA Standard 6001B Flammability, Off-gassing, and Compatibility Requirements and Test Procedures "Determination of Off-gassed Products (Test 7)". Testing took place in the NASA WSTF Molecular Desorption and Analysis Laboratory. One gram of the precursor was placed in a flask within a specimen container. After thermal conditioning for 72 +/- 1 h at 50 +/- 3 deg C (122 +/- 5 deg F), the atmosphere inside the specimen container was analyzed for off-gassed compounds by cryotrap gas chromatography-mass spectrometry (GC-MS) and fixed sample loop GC-flame ionization detection (GC-FID). The specimen container used was glass to minimize potential catalytic surfaces. The identification of compounds was difficult due to the complexity of the vapor phase concentrations and overlapping chromatographic peaks and mass spectra. However, eleven compounds were specifically identified and five compounds or classes of compounds were reported as unidentified. Quantitation of most of the compounds, including unidentified compounds, was as methane. Quantitating compounds or classes of compounds that were detected but for which specific calibration is not established as methane is in accordance with the Test 7 standard protocol. The thermal decomposition temperature of the precursor was significantly higher than the test temperature. Based on thermal decomposition temperature and on an examination of the structure and chemistry of the identified volatile species, the presence of the volatile species appears to be chemically reasonable with respect to the propellant formulation and is at this time attributed to impurities. Further examination of the overall propellant formulation process (including the individual components' synthesis processes) and process quality control (including purity of reagents and possible decomposition reactions) is indicated.

Greene, Benjamin↗
DOE OSTI2022

Flow-Assisted Selective Mineral Extraction from Seawater

The sustainable production of critical materials from natural sources requires a paradigm shift away from currently used resource-intensive processes. In this paper, we report a single-step, laminar co-flow method (LCM) that leverages non-equilibrium conditions to selectively extract pure Mg(OH) 2 from natural seawater. Conventional seawater-based Mg extraction involves adding individual or a combination of precipitants to obtain Mg(OH) 2 , but the co-existence of Ca 2+ unavoidably results in CaCO 3 impurities requiring additional purification steps. Here we show that the non-equilibrium conditions in LCM achieved using a microfluidics device and by simply co-injecting a NaOH solution with seawater can result in improved selectivity for Mg(OH) 2 unlike in conventional bulk mixing method. The resulting precipitates are characterized for composition and the process yield and purity are optimized through systematic variations of the reaction time and the concentration of NaOH. This is the first demonstration of LCM for selective separation, and as a one-step process that does not rely on novel sorbents, membranes, or external stimuli, it is easy to scale-up. LCM has the potential to be broadly relevant to selective separations from complex feed streams and diverse chemistries—enabling more sustainable materials extraction and processing.

54 ENVIRONMENTAL SCIENCES↗