Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “finishing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Si-Cr-Al-Mn Alloy for High Specific Resistivity

Laboratory material produced in budget period one met the target resistivity, mechanical and magnetic requirements for the Go/No-Go decision to move to industrial trials. The chosen chemistry settled on a high Cr strategy, with moderate Mn and Al additions, providing a good comprise on core loss and induction with minimal impact on mechanical properties, important to successful downstream processing. Industrial trials began in budget period two with the chosen chemistry, referred to as Alloy X. Difficulties occurred during initial hot rolling trials. Reheating the material using the standard NOES practice caused slab cracking from high thermal gradients in areas exposed to the roof burners, this was solved using a modified reheat practice. High Cr caused poor dynamic recrystallization during hot rolling, which was solved using a modified hot rolling practice. The high Cr content of the steel also caused poor decarburization during final annealing, which necessitated lowering the melt carbon aim for the final heat, together with a modified decarburization practice. Steel was finished to final thicknesses of 0.20 – 0.50 mm and evaluated for magnetic and mechanical properties. Although the target core loss for the 0.25 and 0.35 mm material was not achieved, significant reductions in high frequency core loss were measured, compared to equivalent commercially available material. Alloy X at 0.35 mm showed a 26 % and 23 % improvement at 400 HZ and 1000 Hz respectively, over Cliffs’ M-19 (0.35 mm) commercially available NOES. At 0.25 mm, Alloy X showed a 23 % and a 26 % improvement at 400 HZ and 1000 Hz respectively, over Cliffs’ HF-10 (0.25 mm) commercially available NOES. The 0.25 mm product was chosen for motor efficiency evaluation. ORNL collaborated with Cleveland-Cliffs (CC) to build, assemble, and test two 5HP motors: a baseline motor with M19 steel and a motor made with high efficiency steel (Alloy X) developed for the project. Overall, results were as expected with comparable performance at low speeds, and with more than 8% efficiency improvement for high speeds. Increased motor steel efficiency at high frequencies not only results in direct efficiency improvements but can yield reductions in motor size and cost by facilitating higher operation speeds, or by increasing the number of poles in the machine. This allows the production of more power-dense motors which are sometimes avoided with conventional material due to increased core losses. The material developed on this project provides more viable options for achieving improved motor efficiency or reduced motor size and cost.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A Data-Driven Approach to Real-World Degradation of Backsheets

The objectives of this project are as follows: • The population behavior of fielded modules in various conditions of use • Predictions of materials in specific climatic zones • Understanding of a module’s local environment in the field on its degradation It aims to understand how and what backsheet materials of photovoltaic modules degrade in the real world field. • Field Survey Protocol This project is started from the protocol, because all the data, information, domain knowledge are from experience of the real world field surveys, which is based on the protocol. The Protocol is explored from the experience of the field survey observations. With the increasing of the field surveys, it is refined for three versions, which are Task 1.0 (Section 3.1), Task 6.0 (Section 3.6), Task 10.0 (Section 3.10) respectively. It includes a document and a training video, which is able to direct other teams to follow the same procedure with the sites surveyed during this project. The documents include the detailed information but is not limited to the terminology definition, instruments SOP, preparation items for the surveys, form for the data collections, the order of the information collection. The final version of the protocol can be found at Appendix A, see Section 5. Additional, It can also be found at Open Science Framework (OSF), see Section 3.18 for detail. • Written Waiver Request Before staring the field surveys, the request of the waiver for international surveys is completed, because the limitation of climate zone in the United States, see Appendix B in Section 6 for the request documents. Unfortunately, only 1 international site from Taiwan, China can be finished, due to the COVID-19. • Field Survey According to the protocol we built in Section 3.1, 3.6 and 3.10, 41 sites have been surveyed across seven different climate zones (Cfa, Csa, Csb, BSk, Dfa, Dfb, Am). A variety of materials, including Polyethylene Naphthalate (PEN), Polyethylene Terephthalate (PET), Polyvinyl Fluoride (PVF), Polyvinylidene Fluoride (PVDF), Acrylic PVDF, Fluoroethylene Vinyl Ether (FEVE), and Glass, were identified. These sites are located in various states including California, South Carolina, New Mexico, Maryland, Ohio, Tennessee, Florida, Massachusetts, Illinois, Minnesota, Oregon, Colorado, and Taiwan, Republic of China. The ages of the sites ranged from 2 - 38 years in service and the field size varied from 1 MW - 25 MW. All requirements for the modeling have been satisfied. Some observations like ’Edge Effect’ for the rows and Junction box heating will also be a useful knowledge to build the model. Section 3.7 provides detailed information on the sites visited during this reporting period.

14 SOLAR ENERGY↗
DOE OSTI2025

Energy Research Frontier Center: Photonics at Thermodynamic Limits

The Photonics at Thermodynamic Limits (PTL) EFRC strives to achieve photonic operations at thermodynamic limits by controlling the flow of photons, electrons, and phonons in atomically architected materials, enabling entirely new energy conversion systems. To achieve this mission, the EFRC united leading researchers in layered and nanostructured materials synthesis, electromagnetic theory, first‐principles quantum theory of materials, and advanced characterization of excited state phenomena. The two-year extension of the EFRC has finished several key efforts started in the EFRC in the previous funding period.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Test Plan for DOE-GENIORS Dyanamic Irradiation Tests

Dynamic irradiation tests will be performed within the DOE-GENIORS collaboration, to be finished by the end of March 2021. These tests will be performed using three different setups, one at INL, one at CEA, and one at CIEMAT. The cis-mTDDGA/PTD chemical system will be used, applying both "extraction" (cis-mTDDGA - n-dodecane/HNO3) and "stripping" (cis-mTDDGA - n-dodecane/PTD - HNO3) conditions. This test plan provides the details and parameters to be used to perform irradiation at the INL using the INL Radiolysis Test Loop.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2025

Wire Arc Additive Manufacturing of Lightweight High Pressure Die Casting Tooling

Oak Ridge National Laboratory (ORNL) and Mercury Marine partnered to develop and test methods for additively manufactured tooling for aluminum die casting applications under CRADA agreement NFE-20-08193. Tooling is the largest capital expense for high production casting projects. The lead time for tooling is often measured in months with a typical project taking 9-12 months to realize Production Part Approval Process (PPAP) ready die cast samples. This project demonstrated the technical viability of rapidly produced steel components for high pressure die casting tooling via Wire Arc Additive Manufacturing (WAAM). A 410 stainless steel tool was redesigned and optimized with conformal cooling channels and additively manufactured. The finished tool was tested and used to produce over 4000 parts, which well surpassed expectations. A secondary objective was to evaluate the durability of multi-material additively manufactured (AM) components with conformal cooling. A large multi-material tool (H13 and 410SSNiMo) was manufactured using the same methods showing potential reductions in used material and cost. However, the H13 section sustained material cracking. Further analysis showed that the potential cause was the CTE mismatch of the two materials at higher temperatures. It is also suggested that the material mix can be used if the steel processing temperature does not exceed 600 ̊C.This project has shown high potential for using the WAAM technology for creating AM parts for aluminum dies casting. However, the multi-material approach requires extended study and tests.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Wire Arc Additive Manufacturing of Lightweight High Pressure Die Casting Tooling

Oak Ridge National Laboratory (ORNL) and Mercury Marine partnered to develop and test methods for additively manufactured tooling for aluminum die casting applications under CRADA agreement NFE- 20-08193. Tooling is the largest capital expense for high production casting projects. The lead time for tooling is often measured in months with a typical project taking 9-12 months to realize Production Part Approval Process (PPAP) ready die cast samples. This project demonstrated the technical viability of rapidly produced steel components for high pressure die casting tooling via Wire Arc Additive Manufacturing (WAAM). A 410 stainless steel tool was redesigned and optimized with conformal cooling channels and additively manufactured. The finished tool was tested and used to produce over 4000 parts, which well surpassed expectations. A secondary objective was to evaluate the durability of multi-material additively manufactured (AM) components with conformal cooling. A large multi-material tool (H13 and 410SSNiMo) was manufactured using the same methods showing potential reductions in used material and cost. However, the H13 section sustained material cracking. Further analysis showed that the potential cause was the CTE mismatch of the two materials at higher temperatures. It is also suggested that the material mix can be used if the steel processing temperature does not exceed 600 ˚C. This project has shown high potential for using the WAAM technology for creating AM parts for aluminum dies casting. However, the multi-material approach requires extended study and tests.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Integrating Machine-learning-assisted Computer Vision with RICH System

Developments in artificial intelligence have vastly expanded the capabilities of robots. Currently, the Spallation Neutron Source (SNS) beamlines at Oak Ridge National Lab (ORNL) have robotic sample loaders to increase the efficiency of running experiments. However, they require retraining if anything about the situation changes, e.g., where the samples are, and cannot notice if errors occur. So, the viability of using computer vision and machine learning to enhance these sample loaders’ functionality was investigated. In this project, the RICH system with a Dobot CR3 6-axis robot present at the VULCAN beamline assisted by an Intel Realsense D435i camera, a unique camera that enables convenient translation of 2D pixel coordinates to 3D world points, was programmed to load ceramic crucibles into a thermogravimetric analyzer (TGA) furnace. An algorithm was constructed in Python with three major phases planned: (1) obtaining a sample, (2) moving it to the target location, and then (3) bringing the sample back to its original location once the experiment finished. In the first phase, the algorithm would dynamically detect sample locations using ArUco markers to recognize the samples’ general location and a custom-trained yolov5 object detection model to locate the crucibles’ centers. Afterward, the robot would be directed to pick up samples based on the crucibles’ calculated positions. In the second phase, the robot would move the sample to a secondary point, reorient its grip, and place the sample at the target location. In the final phase, the robot would determine whether the sample was intact and would bring it back to its original place if it was or raise an alarm. Using this algorithm, the robot was able to pick up different types of crucibles at varying positions. These results indicate that integrating machine-learning-assisted computer vision with robotic sample loaders can result in effective autonomous detection of samples.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Laser Powder Bed Fusion Additive Manufacture Nb1Zr Development

Next generation fission and fusion nuclear reactors require materials that can withstand operating temperatures greater than 500 °C, neutron irradiation doses of up to 200 displacements per atom (dpa), and potentially corrosive coolants such as the alkali liquid metals sodium, lithium, and NaK (Na33K eutectic alloy). Refractory alloys, such as Nb1Zr (Nb-1wt%Zr) and Molybdenum alloy TZM (Mo-0.5wt%Ti-0.08wt%Zr) have been traditionally considered viable candidates for advanced fission and fusion reactor concepts. However, it is relatively difficult to generate complex geometries of interest from these alloys using traditional manufacturing methods. In addition, there needs to be a concentrated effort to address refractory metal challenges at elevated temperature operation. In order to generate complex geometries of interest, modern manufacturing techniques are considered to increase the technological readiness level (TRL), cost-effectiveness, and schedule savings. This work focused on the continued development of laser powder bed fusion (L-PBF) additive manufacturing (AM) to improve both design flexibility, evaluate microstructure and properties, and ultimately accelerate the TRL and qualification of these processes and alloys for components to potentially be put into service. Niobium alloy Nb1Zr was identified through a down-selection process outlined in previous reports as a candidate to develop in L-PBF AM. Historically, Nb1Zr had been explored for high temperature fast spectrum fission reactors for both terrestrial and space applications. Molybdenum alloy TZM has also been considered for these reactor concepts due to exceptional high-temperature strength, creep resistance, and stability under irradiation. L-PBF AM of TZM has previously been investigated at LANL under the Microreactor program, NASA, ORNL, and in academia. However, due to the crack prone nature of TZM, L-PBF AM of TZM resulted in significant microcracking and additional development is required to pursue viable maturation. Other AM methods have been found to be more successful in printing TZM, and those alternatives approaches are discussed in this effort. The efforts detailed in this report focused on continued development of Nb1Zr through L-PBF and development of TZM via L-PBF and electron powder bed fusion (E-PBF). The objective of this work was to further the development of these AM techniques for the chosen refractory alloys, elucidating and addressing associated challenges through characterization of several demonstration builds. At LANL, Nb1Zr builds were completed using an EOS M290 and M400 machines, and a refractory alloy-dedicated L-PBF system, the Xact Metal XM200G, was installed. The XM200G primary purpose was to do the Nb1Zr parameter development process; however, due to difficulties associated with the machine installation and qualification process, it was decided to pivot development to the larger M400 and M290 machines. Although the supply of Nb1Zr powder was limited, it was sufficient to generate sub-scale metallographic specimens for the purpose of parameter development. This was first accomplished on the EOS M400 then the M290 due to machine schedule availability. Further development of TZM has been initiated at the University of Texas El Paso (UTEP) under contract with LANL to use both a heated build envelope L-PBF machine and E-PBF machine that have been found in the literature to mitigate microcracking. UTEP was provided with TZM powder and build plates to support parallel TZM parameter development across both machines. As part of the contract, UTEP will also be conducting microstructural characterization once optimized process parameters have been identified. The optimized process parameters for each machine will be used to generate a series of metallographic, mechanical, and surface finish specimens for subsequent characterization and testing. In the next section, we provide a detailed discussion of the methodology used for investigating the feasibility of leveraging these alloys for use in advanced reactor applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Trends and Effects of Changes in Business Cases for Petroleum Refineries

This study investigates trends and effects in business cases for petroleum refineries with a focus on effects for the state of Oregon for finished gasoline. Recently, the Oregon Department of Energy released the 2024 Oregon Energy Security Plan (ESP) which highlighted the reliance on out of state gasoline imports primarily from refineries located in the state of Washington. This study compiled a list of recent refinery closures in the United States and analyzed the drivers and impacts each refinery closure had to its respective region. The study dives into exploring three refinery closure business cases and past events that impacted gasoline prices in Oregon. Lastly, the paper outlines a potential framework of indicators to analyze the risk of future refinery closures based on the findings. This study hopes to inform stakeholders about the vulnerabilities in Oregon’s fuel supply chain and provide information that can guide strategic planning for future energy security.

02 PETROLEUM↗
DOE OSTI2025

Design and Production for Maximum Structural Efficiency With Respect to Fiber Orientation With Increased Understanding of Hybrid Fiber Flow Behavior

Discontinuous fiber-reinforced thermoplastic composites have gained considerable attention in automotive, aerospace, and other industries, due to their high-rate of production combined with their ability to attain complex and intricate shapes. Among other high-rate thermoplastic manufacturing processes, injection-molding is one of the most common manufacturing methods due to fast production and high surface finishing of complex geometries. Fiber orientation in discontinuous fiber composites plays a pivotal role in determining the mechanical, electrical, and thermomechanical properties, underscoring the necessity to comprehend fiber orientation in injection molded parts. Among different fiber types, glass and carbon fibers are most common in the composite industries. The recent trend of hybrid composites comprising both glass fiber (GF) and carbon fiber (CF) is also gaining importance in the automotive industry. Hybrid fiber options allow designers to optimize the balance between glass and carbon fibers by leveraging the high durability and low cost of GF while the strength and lightweight properties of CF. Consequently, comparing the fiber oriented distribution (FOD) of injection molded composites containing GF, CF, and a hybrid of GF/CF is critical to investigating the local mechanical properties of intricate structures for high-end applications. In Phase I of this project, FOD in injection-molded panels with respect to distance from the gate was analyzed using X-ray computed tomography (X-CT) for GF, CF, and hybrid CF/GF (CGF) reinforced nylon 66. To understand the reason behind the FOD with different fiber types, computational fluid dynamics (CFD) and rheology were performed. Samples were extracted at three locations: near the gate, center, and opposite end. Thickness of the layers of typical skin-shell-core type FOD varies with fiber type and location. GF achieved flow direction alignment (in shell) earlier than viscous CF and CGF near the gate, whereas CF showed the highest flow-direction alignment at the center due to shear induced orientation. At the opposite end, GF experienced more backflow than others indicating faster mold filling owing to its lower viscosity. Hybrid CGF exhibited GF-dominated center and CF-dominated end region. The numerical model used to obtain FOD and rheological predictions for the CF and GF composites served to corroborate the trends observed in the experimental trials. The FOD responses across fiber types and location were reflected in their longitudinal and transverse properties. Only GF showed higher longitudinal modulus over transverse modulus near the gate attributed to rapid alignment, whereas CF and CGF exhibited opposite trend. However, fountain flow enhanced the longitudinal modulus over transverse modulus with the distance for all, particularly for CF. This study offers insights into mold filling behavior of different fibers which are critical in optimizing injection molding conditions for tailored final properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Impacts of Model Building Energy Codes

The Department of Energy (DOE) Building Energy Codes Program (BECP) periodically evaluates national and state-level impacts associated with energy codes in residential and commercial buildings. Pacific Northwest National Laboratory (PNNL), funded by DOE, conducted an assessment of the prospective impacts of national model building energy codes from 2010 through 2040. A previous PNNL study evaluated the impact of the Building Energy Codes Program. A 2016 study looked more broadly at overall code impacts and this report describes the methodology used for the assessment and presents the impacts in terms of energy savings, consumer cost savings, and reduced emissions at the state level and at aggregated levels. In 2021, DOE conducted an interim and limited update to its 2016 study to evaluate potential building code updates using the 2016 methodology. That interim update includes estimated savings resulting from updates to the model energy codes, including the ANSI/ASHRAE/IES Standard 90.1-2016 (ASHRAE 90.1-2016) and 2019 editions, as well as the 2018 and 2021 International Energy Conservation Code (IECC). In 2023, DOE developed a fully updated report that includes code updates (ASHRAE 90.1-2019 and 2021 IECC), as well as additional enhancements and updates, including updated energy prices, annual floorspace additions, state code adoption dates, and emission factors, among others. This current version is another fully updated report that includes code updates (ASHRAE 90.1-2022 and 2024 IECC), as well as additional enhancements and updates, including updated energy prices, state code adoption dates, emission factors, and renewable energy contribution among others. Energy codes follow a three-phase cycle that starts with the development of a new model code, proceeds with the adoption of the new code by states and local jurisdictions, and finishes when the new code is implemented and builders, architects, and engineers are required to comply with the new provisions. The development of new model code editions creates the potential for increased energy savings. After a new model code is adopted, potential savings are realized in the field when new buildings (or additions and alterations) are constructed to comply with the new code. The contributions of all three phases are crucial to the overall impact of codes and are considered in this assessment. Figure ES.1 schematically describes the analysis framework. Energy savings are expressed in terms of energy use intensity (EUI) in the figure.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Aerogel with Unparalleled Performance and Cost-Effectiveness for All Insulation Needs (CRADA Final Report)

Westwood Aerogel investigated the reproducible production of an ambiently or electromagnetic spectrum assisted drying of extremely porous aerogel materials. Traditional aerogel processing is limited by low throughput and scalability due to supercritical drying. Westwood Aerogel’s advanced manufacturing process enables commercialization and deployment at scale, making aerogel materials more accessible to a range of industries and applications. We focused on shifting from the lab scale environment to manufacturing prototypes. The initial manufacturing model is based on the float glass process, which is the industry standard for glass window production, and the paper drying process. By incorporating an ambient drying process a continuous line model can be used from start to finish. The project team worked to develop a continuous manufacturing system to scale-up and reduce costs while maintaining the lightweight and insulative properties of aerospace-grade aerogel. While aerogels are extremely insulative, lightweight, and thin materials (making them ideal insulators across application spaces), high costs and stagnant innovation have hampered their wider adoption. Traditional manufacturing of aerogel requires supercritical extraction of pore fluid to obtain highly insulating materials, which is an energy intensive batch process and limits aerogel production output. Westwood Aerogel’s proprietary ambient drying process enables the continuous production of highly insulative aerogel materials without the use of supercritical extraction.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Cost Effectiveness of Laser Powder Bed Fusion for Heavy Duty Applications

ORNL (Contractor) and Cummins Inc. (Participant) collaborated to determine the cost effectiveness of laser powder bed fusion (LPBF) for heavy duty applications. The team demonstrated that coupons can be fabricated with two distinct process parameters i.e., different process parameters for the bulk and surface of the material. This is important for enabling the manufacturing of components in a production environment where the bulk of the material can be processed rapidly while high quality surface finish can minimize post-process machining as well as enable superior fatigue performance if the material were to be used in as-deposited condition.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Precision Polishing of Spheres Via In-Situ Process Monitoring and Machine-Learning-Based Optimization

Precision polishing for high surface finish is a vital step in the making of many high-tech components for optical and semiconductor modules as well as for wide ranging experimental samples for HED science that is at the core of LLNL’s mission. In particular, the fabrication of extremely smooth and round spheres comprised of low atomic number materials (low-Z such as high-density carbon or HDC, beryllium, hydrocarbon polymers, etc.) for Inertial Confinement Fusion (ICF) is entirely reliant on specialized polishing processes to achieve the surface smoothness.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Electropolishing-induced topographic defects in niobium: Insights and Implications for SRF

Electropolishing (EP) is the premier surface preparation method for high-Q, high-gradient superconducting RF cavities made of Nb. This leaves behind an apparently smooth surface, yet the achievable peak magnetic fields fall well below the superheating field of Nb, in most cases. In this work, the ultimate surface finish of EP was investigated by studying its effect on highly polished Nb samples. EP introduces high slope angle sloped-steps at grain boundaries. The magnetic field enhancement and superheating field suppression factors associated with such a geometry are calculated in the London theory. Despite the by-eye smoothness of electropolished Nb, such defects compromise the stability of the low-loss Meissner state, likely limiting the achievable peak accelerating fields in superconducting RF cavities. Finally, the impact of surface roughness on impurity diffusion is investigated which can link surface roughness to the effectiveness of heat treatments like low-temperature baking or nitrogen infusion in the vortex nucleation or hydride hypotheses. Surface roughness tends to decrease the effective dose of impurities as a result of the expansion of impurities into regions with greater internal angle. The effective dose of impurities can be protected by minimizing slope angles and step heights, ensuring uniformity.

Lechner, Eric [Thomas Jefferson National Accelerat↗
DOE OSTI2026

Advanced Manufacturing of Cathode Materials for Lithium-ion Batteries

Original objectives (per the Statement of Project Objectives) centered on developing and translating a continuous pilot process for cathode materials production while targeting (i) a 29% manufacturing cost reduction, (ii) an 82% energy consumption reduction for cathode production, and (iii) a doubling of manufacturing productivity. Planned validation included characterization at appropriate analytical facilities and electrochemical performance evaluation progressing from half-cells to pouch-cell formats, with a pathway to kilogram-scale production of finished cathode materials for representative testing. Scope evolution: During execution, the project team identified that the surfactant-enabled chemistry offered high selectivity for lithium precipitation from brine sources. A formal scope revision shifted the final project year from cathode manufacturing development to direct lithium extraction/lithium recovery, while maintaining the overarching intent of cost reduction and process simplification relevant to the battery supply chain.

25 ENERGY STORAGE↗
DOE OSTI2026

Intelligent Experiments Through Real-time AI: Fast Data Processing and Autonomous Detector Control for sPHENIX and Future EIC Detectors (Final Report)

The overall vision of this project was to integrate real-time artificial intelligence (AI) directly into the data acquisition and detector-control systems of nuclear physics experiments, including both fast online event selection and an autonomous detector-control feedback loop. The work carried out under the award focused on the fast online event-selection half of that vision: the efficient recording of low-momentum heavy-flavor (HF) hadron decays in proton-proton collisions at the sPHENIX experiment at the Relativistic Heavy Ion Collider (RHIC)—an observable that requires fast tracking and topological trigger selection not previously demonstrated at RHIC, and that is essential for QCD studies at future facilities such as the Electron-Ion Collider (EIC). The autonomous detector-control (GPU-based feedback) component named in the project title remained a design concept and was not implemented under this award. The Massachusetts Institute of Technology (MIT) group led the offline simulation and data processing needed to train the machine-learning (ML) models, the translation of trained models to Field-Programmable Gate Array (FPGA) firmware using the hls4ml framework, and the physics validation of heavy-flavor reconstruction. Over the award period, the team developed and hardware-tested the principal components of an AI-based heavy-flavor trigger on simulated and recorded sPHENIX tracker data: a software Bipartite Graph Attention Network (BiGAT) trigger model reaching > 95% signal efficiency at 99% background rejection; an FPGA-native hit clusterizer matching the offline clustering; smaller networks synthesized to FPGA within the required sub-10 µs latency; and an assembled decoder–clusterizer–inference firmware chain exercised on the FELIX readout board. A complete, fully integrated hardware demonstrator was not finished within the award period. This report documents the project goals, the MIT group’s contributions, the technical accomplishments, and the outlook toward applications at the future EIC ePIC detector.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗