SEARCH · Engineering Papers

Results for “experimental data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Analysis of multifastener composite joints

A new numerical procedure for determining load proportioning in multiple-hole mechanical joints in composite plates is presented. The joints are loaded in double lap fashion in tension with pins through the holes. The commercial finite-element program ABAQUS is used to predict the load proportioning among holes using two independent plane stress finite-element models, one representing the composite inner lap and one representing the two steel outer laps, interacting through rigid circular surfaces. The circular surfaces effectively represent rigid pins. Load proportioning is predicted for a number of geometries. Excellent correlation with experimental data is obtained. Experimental and computed surface strains are also found to compare well. The assumption of a radial cosine distribution of contact stress between pin and hole is shown to be substantially in error for some holes.

Griffin, O. H., Jr.↗

NASA NTRS1951

Dynamics of a turbojet engine considered as a quasi-static system

A determination of the dynamic characteristics of a typical turbojet engine with a centrifugal compressor, a sonic-flow turbine-nozzle diaphragm, and fixed area exhaust nozzle is presented. A generalized equation for transient behavior of the engine was developed; this equation was then verified by calculations using compressor and turbine performance charts extrapolated from equilibrium operating data and by experimental data obtained from an engine operated under transients in fuel flow. The results indicate that a linear differential equation for engine acceleration as a function of fuel flow and engine speed for operation near a steady-state operating condition can be written. The coefficients of this equation can be obtained either from actual transient data or, with a fair degree of accuracy, from the steady-state performance maps of the compressor and turbine, and can be corrected for altitude in the same manner that steady-state performance data are corrected.

Otto, Edward W↗

NASA NTRS1996

Numerical simulation of jet aerodynamics using the three-dimensional Navier-Stokes code PAB3D

This report presents a unified method for subsonic and supersonic jet analysis using the three-dimensional Navier-Stokes code PAB3D. The Navier-Stokes code was used to obtain solutions for axisymmetric jets with on-design operating conditions at Mach numbers ranging from 0.6 to 3.0, supersonic jets containing weak shocks and Mach disks, and supersonic jets with nonaxisymmetric nozzle exit geometries. This report discusses computational methods, code implementation, computed results, and comparisons with available experimental data. Very good agreement is shown between the numerical solutions and available experimental data over a wide range of operating conditions. The Navier-Stokes method using the standard Jones-Launder two-equation kappa-epsilon turbulence model can accurately predict jet flow, and such predictions are made without any modification to the published constants for the turbulence model.

Pao, S. Paul↗

NASA NTRS2005

Failure Models and Criteria for FRP Under In-Plane or Three-Dimensional Stress States Including Shear Non-Linearity

A set of three-dimensional failure criteria for laminated fiber-reinforced composites, denoted LaRC04, is proposed. The criteria are based on physical models for each failure mode and take into consideration non-linear matrix shear behaviour. The model for matrix compressive failure is based on the Mohr-Coulomb criterion and it predicts the fracture angle. Fiber kinking is triggered by an initial fiber misalignment angle and by the rotation of the fibers during compressive loading. The plane of fiber kinking is predicted by the model. LaRC04 consists of 6 expressions that can be used directly for design purposes. Several applications involving a broad range of load combinations are presented and compared to experimental data and other existing criteria. Predictions using LaRC04 correlate well with the experimental data, arguably better than most existing criteria. The good correlation seems to be attributable to the physical soundness of the underlying failure models.

Pinho, Silvestre T.↗

NASA NTRS2004

Glenn Heat Transfer Simulation and Solver Graphical User Interface: Development and Testing

In the Tui ine Branch of the Turbomachinery and Propulsion Systems Division, researching and developing efficient turbine aerothermodynamics technologies is the main objective. Creating effective turbines for jet engines is a process which, if based purely on physical experimental testing, would be extremely expensive. It is for this reason, and also for the reasons of speed and ease, that the Turbine Branch spends a large amount of effort working with simulations of turbines. Specifically, they focus their work on two main fields: Computational Field Dynamics (CFD), and Experimental data analysis. The experimental field involves comparing experimental results to simulated results, whereas the CFD field involves running these simulations. The simulations are applied to aerodynamics and heat transfer cases, for both steady and unsteady flow conditions. By and large this work is applied to the domain of flow and heat transfer in axial turbines. The main application used to run these heat flow simulations is GlennHT. This program, recently rewritten in FORTRAN 90, allows the user to input a job file which specifies all the necessary parameters needed to simulate flow through a user-defined grid. There are several other executables used as well, ranging in application from converting grid files to and from particular formats, to merging blocks in a connectivity file, to converting connectivity files to a GlennHT compatible format. All of these executables are run from the command line in a terminal; some of them have interactive prompts where the user must specify the files to be manipulated after the program starts, while others take all of their parameters from the command line. With this amount of variation comes a good deal of commands and formats to memorize, which can cause slower and less efficient work, as users may forget how to execute a certain program, or not remember the pathnames of the files they wish to use. Two years ago, steps were made to expedite this process with a graphical user interface (GUI) that combines the functionality of all the executables along with adding some new functionality, such as residuals graphing and boundary conditions creation. Upon my beginning here at Glenn, many parts of the GUI, which was developed in Java, were nonfunctional. There were also issues with cross-platforming, as systems in the branch were transitioning from Silicon Graphics (SGI) machines to Linux machines. My goals this summer are to finish the parts of the GUI that are not yet completed, fix parts that did not work correctly, expand the functionality to include other useful features, such as grid surface highlighting, and make the system compatible with both Linux and SGI. I will also be heavily testing the system and providing sufficient documentation on how to use the GUI, as no such documentation existed previously.

Kardamis, Joseph R.↗

NASA NTRS2006

PAB3D: Its History in the Use of Turbulence Models in the Simulation of Jet and Nozzle Flows

This is a review paper for PAB3D s history in the implementation of turbulence models for simulating jet and nozzle flows. We describe different turbulence models used in the simulation of subsonic and supersonic jet and nozzle flows. The time-averaged simulations use modified linear or nonlinear two-equation models to account for supersonic flow as well as high temperature mixing. Two multiscale-type turbulence models are used for unsteady flow simulations. These models require modifications to the Reynolds Averaged Navier-Stokes (RANS) equations. The first scheme is a hybrid RANS/LES model utilizing the two-equation (k-epsilon) model with a RANS/LES transition function, dependent on grid spacing and the computed turbulence length scale. The second scheme is a modified version of the partially averaged Navier-Stokes (PANS) formulation. All of these models are implemented in the three-dimensional Navier-Stokes code PAB3D. This paper discusses computational methods, code implementation, computed results for a wide range of nozzle configurations at various operating conditions, and comparisons with available experimental data. Very good agreement is shown between the numerical solutions and available experimental data over a wide range of operating conditions.

Abdol-Hamid, Khaled S.↗

NASA NTRS2007

Spatial Pattern of Cell Damage in Tissue from Heavy Ions

A new Monte Carlo algorithm was developed that can model passage of heavy ions in a tissue, and their action on the cellular matrix for 2- or 3-dimensional cases. The build-up of secondaries such as projectile fragments, target fragments, other light fragments, and delta-rays was simulated. Cells were modeled as a cell culture monolayer in one example, where the data were taken directly from microscopy (2-d cell matrix). A simple model of tissue was given as abstract spheres with close approximation to real cell geometries (3-d cell matrix), as well as a realistic model of tissue was proposed based on microscopy images. Image segmentation was used to identify cells in an irradiated cell culture monolayer, or slices of tissue. The cells were then inserted into the model box pixel by pixel. In the case of cell monolayers (2-d), the image size may exceed the modeled box size. Such image was is moved with respect to the box in order to sample as many cells as possible. In the case of the simple tissue (3-d), the tissue box is modeled with periodic boundary conditions, which extrapolate the technique to macroscopic volumes of tissue. For real tissue, specific spatial patterns for cell apoptosis and necrosis are expected. The cell patterns were modeled based on action cross sections for apoptosis and necrosis estimated based on BNL data, and other experimental data.

Ponomarev, Artem L.↗

NASA NTRSDate not supplied

TPSAS-NF1676L-13635-DND

Objectives of AePW: Assess state-of-the-art Computational Aeroelasticity (CAe) methods as practical tools for the prediction of static and dynamic aeroelastic phenomena and responses on relevant geometries. - Perform comparative computational studies on selected test cases - Identify errors & uncertainties in computational aeroelastic methods - Identify gaps in existing aeroelastic databases - Provide roadmap of path forward (additional existing data sets, new experimental data sets, and analytical methods developments).

Walt Silva↗

NASA NTRS2004

Transonic Drag Prediction on a DLR-F6 Transport Configuration Using Unstructured Grid Solvers

A second international AIAA Drag Prediction Workshop (DPW-II) was organized and held in Orlando Florida on June 21-22, 2003. The primary purpose was to inves- tigate the code-to-code uncertainty. address the sensitivity of the drag prediction to grid size and quantify the uncertainty in predicting nacelle/pylon drag increments at a transonic cruise condition. This paper presents an in-depth analysis of the DPW-II computational results from three state-of-the-art unstructured grid Navier-Stokes flow solvers exercised on similar families of tetrahedral grids. The flow solvers are USM3D - a tetrahedral cell-centered upwind solver. FUN3D - a tetrahedral node-centered upwind solver, and NSU3D - a general element node-centered central-differenced solver. For the wingbody, the total drag predicted for a constant-lift transonic cruise condition showed a decrease in code-to-code variation with grid refinement as expected. For the same flight condition, the wing/body/nacelle/pylon total drag and the nacelle/pylon drag increment predicted showed an increase in code-to-code variation with grid refinement. Although the range in total drag for the wingbody fine grids was only 5 counts, a code-to-code comparison of surface pressures and surface restricted streamlines indicated that the three solvers were not all converging to the same flow solutions- different shock locations and separation patterns were evident. Similarly, the wing/body/nacelle/pylon solutions did not appear to be converging to the same flow solutions. Overall, grid refinement did not consistently improve the correlation with experimental data for either the wingbody or the wing/body/nacelle pylon configuration. Although the absolute values of total drag predicted by two of the solvers for the medium and fine grids did not compare well with the experiment, the incremental drag predictions were within plus or minus 3 counts of the experimental data. The correlation with experimental incremental drag was not significantly changed by specifying transition. Although the sources of code-to-code variation in force and moment predictions for the three unstructured grid codes have not yet been identified, the current study reinforces the necessity of applying multiple codes to the same application to assess uncertainty.

Lee-Rausch, E. M.↗

NASA NTRS1972

Experiment and analysis of directional effects on radiant heat transfer.

Critical examination of the validity of the commonly used simplified models for predicting local and overall radiant heat interchange among real surfaces. The spectral local irradiation was measured at wavelengths of 3.08 and 4.51 microns in a configuration consisting of three plane parallel surfaces of finite extent. The test surfaces were gold with mechanical roughness and temperature varying from 0.02 to 7.1 microns and 77 to 760 K, respectively. Comparisons between experimental data and predictions for six different models ranging from the simple diffuse to the most detailed diffuse-plus-specular-directional-property model with specular component calculated according to Beckmann are presented. It is shown that the calculation of the overall irradiation using appropriate constant-property models agrees well with the experimental data to within combined experimental and analytical uncertainty. In general, it is concluded that for accurate prediction of local irradiation the directional characteristics of the surfaces must be considered.

Toor, J. S.↗

NASA NTRS2004

Verification of an Analytical Method for Measuring Crystal Nucleation Rates in Glasses from DTA Data

A recently proposed analytical (DTA) method for estimating the nucleation rates in glasses has been evaluated by comparing experimental data with numerically computed nucleation rates for a model lithium disilicate glass. The time and temperature dependent nucleation rates were predicted using the model and compared with those values from an analysis of numerically calculated DTA curves. The validity of the numerical approach was demonstrated earlier by a comparison with experimental data. The excellent agreement between the nucleation rates from the model calculations and fiom the computer generated DTA data demonstrates the validity of the proposed analytical DTA method.

Ranasinghe, K. S.↗

NASA NTRS1989

Prediction of fatigue-crack growth in a high-strength aluminum alloy under variable-amplitude loading

The present paper is concerned with the application of an analytical crack-closure model to study crack growth under various load histories. The model was based on a crack-tip plasticity concept like the Dugdale model, but modified to leave plastically deformed material in the wake of the advancing crack tip. The effect of material thickness on plasticity was accounted for by using a constraint factor on tensile yielding at the crack tip. The model was used to correlate crack-growth rates under constant-amplitude loading, and to predict crack growth under variable-amplitude loading on a high-strength aluminum alloy (7475-T7351) sheet material. The experimental data were obtained from Zhang et al. Predicted crack-growth lives agreed well with experimental data. For ten crack-growth tests subjected to various variable-amplitude load histories, the ratio of predicted-to-experimental lives ranged from 0.54 to 1.19. The mean value of the ratio of predicted-to-experimental lives was 0.95 and the standard error was 0.2 using a constraint factor of 1.9 in the model. Crack-opening stresses calculated from the model were significantly different from those determined by Zhang et al. using a striation-based experimental method.

Newman, J. C., Jr.↗

NASA NTRS1989

Prediction of fatigue-crack growth in a high-strength aluminum alloy under variable-amplitude loading

The present paper is concerned with the application of an analytical crack-closure model to study crack growth under various load histories. The model was based on a concept like the Dugdale model, but modified to leave plastically deformed material in the wake of the advancing crack tip. The thickness effect was accounted for by using a 'constraint' factor on tensile yielding at the crack tip. The model was used to correlate crack-growth rates under constant-amplitude loading, and to predict crack growth under variable-amplitude loading on a high-strength aluminum alloy (7475-T7351) sheet material. The experimental data was obtained from Zhang et al. Predicted crack-growth lives agreed well with experimental data. For ten crack-growth tests subjected to various variable-amplitude load histories, the ratio of predicted-to-experimental lives ranged from 0.54 to 1.19. The mean value of predicted-to-experimental lives was 0.95 with a standard error of 0.2 for a constraint factor of 1.9.

Newman, J. C., Jr.↗

NASA NTRS1977

An approximate calculation of the strong interaction on a transonic airfoil

This paper describes an interactive computational scheme that calculates the transonic flow field over an airfoil. The inviscid flow, the turbulent boundary layer in the weak interaction region, and the elliptic flow in the strong interaction region are computed separately, and the solutions are matched iteratively in a direct, second-order interaction scheme. The pressure distribution, obtained from a transonic, small-perturbation solution, is prescribed on the boundary layer and the Navier-Stokes equations and the ensuing displacement thicknesses are used to modify the inviscid flow. The best overall results are obtained by using a turbulence model that eliminates the eddy viscosity in the strong interaction region. Computed pressure distributions are compared with experimental data and with Navier-Stokes solutions. In weak interactions, the agreement with experimental data is very good, as it is also in strong interactions except for the pressures in the separated-flow region. There the agreement is qualitative only, and the pressure recovery is too high. The results in both cases are superior or equal to those of the Navier-Stokes solutions, and the present method is significantly faster.

Seginer, A.↗

NASA NTRS1983

Aeroelastic loads prediction for an arrow wing. Task 2: Evaluation of semi-empirical methods

The development and evaluation of a semi empirical method to predict pressure distributions on a deformed wing by using an experimental data base in addition to a linear potential flow solution is described. The experimental data accounts for the effects of aeroelasticity by relating the pressures to a parameter which is influenced by the deflected shape. Several parameters were examined before the net leading edge suction coefficient was selected as the best.

Wery, A. C.↗

NASA NTRS1988

Evaluation of three turbulence models for the prediction of steady and unsteady airloads

Two dimensional quasi-three dimensional Navier-Stokes solvers were used to predict the static and dynamic airload characteristics of airfoils. The following three turbulence models were used: the Baldwin-Lomax algebraic model, the Johnson-King ODE model for maximum turbulent shear stress, and a two equation k-e model with law-of-the-wall boundary conditions. It was found that in attached flow the three models have good agreement with experimental data. In unsteady separated flows, these models give only a fair correlation with experimental data.

Wu, Jiunn-Chi↗

NASA NTRS1989

Evaluation of three turbulence models for the prediction of steady and unsteady airloads

Wu, Jiunn-Chi↗

NASA NTRS1998

Improved Modeling of Finite-Rate Turbulent Combustion Processes in Research Combustors

The objective of this thesis is to further develop and test a stochastic model of turbulent combustion in recirculating flows. There is a requirement to increase the accuracy of multi-dimensional combustion predictions. As turbulence affects reaction rates, this interaction must be more accurately evaluated. In this work a more physically correct way of handling the interaction of turbulence on combustion is further developed and tested. As turbulence involves randomness, stochastic modeling is used. Averaged values such as temperature and species concentration are found by integrating the probability density function (pdf) over the range of the scalar. The model in this work does not assume the pdf type, but solves for the evolution of the pdf using the Monte Carlo solution technique. The model is further developed by including a more robust reaction solver, by using accurate thermodynamics and by more accurate transport elements. The stochastic method is used with Semi-Implicit Method for Pressure-Linked Equations. The SIMPLE method is used to solve for velocity, pressure, turbulent kinetic energy and dissipation. The pdf solver solves for temperature and species concentration. Thus, the method is partially familiar to combustor engineers. The method is compared to benchmark experimental data and baseline calculations. The baseline method was tested on isothermal flows, evaporating sprays and combusting sprays. Pdf and baseline predictions were performed for three diffusion flames and one premixed flame. The pdf method predicted lower combustion rates than the baseline method in agreement with the data, except for the premixed flame. The baseline and stochastic predictions bounded the experimental data for the premixed flame. The use of a continuous mixing model or relax to mean mixing model had little effect on the prediction of average temperature. Two grids were used in a hydrogen diffusion flame simulation. Grid density did not effect the predictions except for peak temperature and tangential velocity. The hybrid pdf method did take longer and required more memory, but has a theoretical basis to extend to many reaction steps which cannot be said of current turbulent combustion models.

VanOverbeke, Thomas J.↗