Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electron tubes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

The Apollo 15 regolith - Comparative petrology of drive tube 15010/15011 and drill core section 15003

Two Apollo 15 regolith cores - double drive-tube 15010/15011 and deep drill core section 15003 - were compared. The drive tube was taken from near the edge of Hadley Rille within the mare region and the drill core was taken from the landing site, approximately the same distance as the drive tube from the Apennine Front. Optical modes were done on the two cores, each of which was divided into three stratigraphic units defined by minor differences in grain size and modal abundances. Electron microprobe data were collected on the mineral and glass fragments within each unit. Fused-soil-free bulk chemistries were calculated for each unit by modal recombination, using our modal data and average compositional and density data for soil components. It is found that the drive tube and drill core section are fairly homogeneous units both chemically and modally. Both soils are submature to immature. There are, however, significant differences between the cores. The drill core shows significant enrichments of highland lithic-fragments and highland-derived minerals and glasses relative to the drive tube. These differences are attributed to the fresh nature of the drive tube soil whose major source material is mare basalt ejecta from the shallow bedrock.

Walker, R. J.↗
NASA NTRS2000

Modular Low-Heater-Power Cathode/Electron Gun Assembly for Microwave and Millimeter Wave Traveling Wave Tubes

A low-cost, low-mass, electrically efficient, modular cathode/electron gun assembly has been developed by FDE Inc. of Beaverton, Oregon, under a Small Business Innovation Research (SBIR) contract with the NASA Glenn Research Center at Lewis Field. This new assembly offers significant improvements in the design and manufacture of microwave and millimeter wave traveling-wave tubes (TWT's) used for radar and communications. It incorporates a novel, low-heater-power, reduced size and mass, high-performance barium dispenser type thermionic cathode and provides for easy integration of the cathode into a large variety of conventional TWT circuits. Among the applications are TWT's for Earth-orbiting communication satellites and for deep space communications, where future missions will require smaller spacecraft, higher data transfer rates (higher frequencies and radiofrequency output power), and greater electrical efficiency. A particularly important TWT application is in the microwave power module (a hybrid microwave/millimeter wave amplifier consisting of a low-noise solid-state driver, a small TWT, and an electronic power conditioner integrated into a single compact package), where electrical efficiency and thermal loading are critical factors and lower cost is needed for successful commercialization. The design and fabrication are based on practices used in producing cathode ray tubes (CRT's), which is one of the most competitive and efficient manufacturing operations in the world today. The approach used in the design and manufacture of thermionic cathodes and electron guns for CRT's has been optimized for fully automated production, standardization of parts, and minimization of costs. It is applicable to the production of similar components for microwave tubes, with the additional benefits of low mass and significantly lower cathode heater power (less than half that of dispenser cathodes presently used in TWT s). Modular cathode/electron gun assembly. The modular cathode/electron gun assembly consists of four subassemblies the cathode, the focus electrode, the header (including the electrical feedthroughs), and the gun envelope (including the anode) a diagram of which is shown. The modular construction offers a number of significant advantages, including flexibility of design, interchangeability of parts, and a drop-in final assembly procedure for quick and accurate alignment. The gun can accommodate cathodes ranging in size from 0.050 to 0.250-in. in diameter and is applicable to TWT's over a broad range of sizes and operating parameters, requiring the substitution of only a few parts: that is, the cathode, focus electrode, and anode. The die-pressed cathode pellets can be made with either flat or concave (Pierce gun design) emitting surfaces. The gun can be either gridded (pulse operation) or ungridded (continuous operation). Important factors contributing to low cost are the greater use of CRT materials and parts, the standardization of processes (welding and mechanical capture), and tooling amenable to automated production. Examples are the use of simple shapes, drawn or stamped metal parts, and parts joined by welding or mechanical capture. Feasibility was successfully demonstrated in the retrofit and testing of a commercial Kaband (22-GHz) TWT. The modular cathode/electron gun assembly was computer modeled to replicate the performance of the original electron gun and fabricated largely from existing CRT parts. Significant test results included demonstration of low heater power (1.5-W, 1010 C brightness temperature for a 0.085-in.-diameter cathode), mechanical ruggedness (100g shock and vibration tests in accordance with military specifications (MIL specs)), and a very fast warmup. The results of these tests indicate that the low-cost CRT manufacturing approach can be used without sacrificing performance and reliability.

Wintucky, Edwin G.↗
NASA NTRS1979

Analytical prediction with multidimensional computer programs and experimental verification of the performance, at a variety of operating conditions, of two traveling wave tubes with depressed collectors

Experimental and analytical results are compared for two high performance, octave bandwidth TWT's that use depressed collectors (MDC's) to improve the efficiency. The computations were carried out with advanced, multidimensional computer programs that are described here in detail. These programs model the electron beam as a series of either disks or rings of charge and follow their multidimensional trajectories from the RF input of the ideal TWT, through the slow wave structure, through the magnetic refocusing system, to their points of impact in the depressed collector. Traveling wave tube performance, collector efficiency, and collector current distribution were computed and the results compared with measurements for a number of TWT-MDC systems. Power conservation and correct accounting of TWT and collector losses were observed. For the TWT's operating at saturation, very good agreement was obtained between the computed and measured collector efficiencies. For a TWT operating 3 and 6 dB below saturation, excellent agreement between computed and measured collector efficiencies was obtained in some cases but only fair agreement in others. However, deviations can largely be explained by small differences in the computed and actual spent beam energy distributions. The analytical tools used here appear to be sufficiently refined to design efficient collectors for this class of TWT. However, for maximum efficiency, some experimental optimization (e.g., collector voltages and aperture sizes) will most likely be required.

Dayton, J. A., Jr.↗
NASA NTRS1971

Spaceborne electronic imaging systems

Criteria and recommended practices for the design of the spaceborne elements of electronic imaging systems are presented. A spaceborne electronic imaging system is defined as a device that collects energy in some portion of the electromagnetic spectrum with detector(s) whose direct output is an electrical signal that can be processed (using direct transmission or delayed transmission after recording) to form a pictorial image. This definition encompasses both image tube systems and scanning point-detector systems. The intent was to collect the design experience and recommended practice of the several systems possessing the common denominator of acquiring images from space electronically and to maintain the system viewpoint rather than pursuing specialization in devices. The devices may be markedly different physically, but each was designed to provide a particular type of image within particular limitations. Performance parameters which determine the type of system selected for a given mission and which influence the design include: Sensitivity, Resolution, Dynamic range, Spectral response, Frame rate/bandwidth, Optics compatibility, Image motion, Radiation resistance, Size, Weight, Power, and Reliability.

Source record↗
NASA NTRS1990

Simulation studies of electron acceleration by ion ring distributions in solar flares

A 2.5-dimensional fully relativistic EM, particle-in-cell code (PIC) is used to investigate a potential electron acceleration mechanism in solar flares. The free energy is provided by ions which have a ring velocity distribution about the magnetic-field direction. Ion rings may be produced by perpendicular shocks, which could in turn be generated by the super-Alfvenic motion of magnetic flux tubes emerging from the photosphere or by coronal mass ejections. Such ion distributions are known to be unstable to the generation of lower hybrid waves, which have phase velocities in excess of the electron thermal speed parallel to the field and can, therefore, resonantly accelerate electrons in that direction. The simulations show the transfer of perpendicular ion energy to energetic electrons via lower hybrid wave turbulence. With plausible ion ring velocities, the process can account for the observationally inferred fluxes and energies of non-thermal electrons during the impulsive phase of flares.

Mcclements, K. G.↗
NASA NTRS1974

Integrated structure vacuum tube: A Concept

Cathode emission is made to occur by heating entire structure to 600 C, and positive potential is applied to anode with negative potential on grids. Electron flow takes place from ring to circular anode through electric field produced by grids.

Dimeff, J.↗
NASA NTRS1990

A high-efficiency ferruleless coupled-cavity traveling-wave tube with phase-adjusted taper

The design and performance of the first traveling-wave tube (TWT) to be built with a phase-adjusted taper (PAT) is discussed. By adjusting the phase of the electron bunch with respect to the RF wave for strong electron bunch formation at the beginning of the taper and strong power conversion at the end, the PAT achieves a high efficiency of power conversion from the electron beam to the RF wave. A PAT incorporated into the output section of a baseline 29-30 GHz ferruleless coupled-cavity TWT experimentally increased the peak RF power from 420 to 1000 W and the peak RF interaction efficiency from 9.6 to 22.6 percent.

Wilson, Jeffrey D.↗
NASA NTRS2004

A parametric study of single-wall carbon nanotube growth by laser ablation

Results of a parametric study of carbon nanotube production by the double-pulse laser oven process are presented. The effect of various operating parameters on the production of single-wall carbon nanotubes (SWCNTs) is estimated by characterizing the nanotube material using analytical techniques, including scanning electron microscopy, transmission electron microscopy, thermo gravimetric analysis and Raman spectroscopy. The study included changing the sequence of the laser pulses, laser energy, pulse separation, type of buffer gas used, operating pressure, flow rate, inner tube diameter, as well as its material, and oven temperature. It was found that the material quality and quantity improve with deviation from normal operation parameters such as laser energy density higher than 1.5 J/cm2, pressure lower than 67 kPa, and flow rates higher than 100 sccm. Use of helium produced mainly small diameter tubes and a lower yield. The diameter of SWCNTs decreases with decreasing oven temperature and lower flow rates.

Nanotubes, Carbon/chemistry↗
NASA NTRS1980

Survey of the plasma electron environment of Jupiter: A view from Voyager

The plasma environment within Jupiter's bow shock is considered in terms of the in situ, calibrated electron plasma measurements made between 10 eV and 5.95 keV by the Voyager plasma science experiment (PLS). Measurements were analyzed and corrected for spacecraft potential variations; the data were reduced to nearly model independent macroscopic parameters of the local electron density and temperature. It is tentatively concluded that the radial temperature profile within the plasma sheet is caused by the intermixing of two different electron populations that probably have different temporal histories and spatial paths to their local observation. The cool plasma source of the plasma sheet and spikes is probably the Io plasma torus and arrives in the plasma sheet as a result of flux tube interchange motions or other generalized transport which can be accomplished without diverting the plasma from the centrifugal equator. The hot suprathermal populations in the plasma sheet have most recently come from the sparse, hot mid-latitude "bath" of electrons which were directly observed juxtaposed to the plasma sheet.

Scudder, J. D.↗
NASA NTRS1979

Jovian longitudinal control of Io-related radio emissions

A theoretical model is proposed to explain the control of Io-related radio emissions by Jupiter's rotational phase. The model is based on the hypothesis that the radio emissions are generated by Birkeland currents flowing between Io and the Jovian ionosphere. Specifically, it is suggested that the precipitation of radiation-belt electrons within a certain range of Jovian longitudes produces a restricted region of enhanced ionization and correspondingly enhanced conductivity in Jupiter's ionosphere and that the Io-Jupiter Birkeland current and the associated radio emissions are dramatically increased when Io's flux tube encounters this sector of enhanced ionization in Jupiter's ionosphere. The magnitude of the current is found to be about 100,000 A at most Jovian longitudes because of ionospheric resistance. It is estimated that within the favored longitudinal sector electron precipitation produces an enhancement of this current by one to three orders of magnitude. The model predictions are compared with observations made during the Pioneer 10 and 11 flybys, and satisfactory agreement is obtained.

Dessler, A. J.↗
NASA NTRS1975

A model-based analysis of a display for helicopter landing approach

A control theoretic model of the human pilot was used to analyze a baseline electronic cockpit display in a helicopter landing approach task. The head down display was created on a stroke written cathode ray tube and the vehicle was a UH-1H helicopter. The landing approach task consisted of maintaining prescribed groundspeed and glideslope in the presence of random vertical and horizontal turbulence. The pilot model was also used to generate and evaluate display quickening laws designed to improve pilot vehicle performance. A simple fixed base simulation provided comparative tracking data.

Hess, R. A.↗
NASA NTRS1992

Coupled-Cavity Traveling-Wave Tube Has Phase-Adjusted Taper

In structure of improved coupled-cavity traveling-wave tube amplifier, lengths of cavities chosen according to computer-generated, nonlinear taper to increase efficiency of conversion of power from electron beam to microwave. Design calls for "phase-adjusted taper," calculated so phase of electron bunches with respect to phase of microwave changes gradually from value conducive to formation of strong bunches to value conducive to strong transfer of power to microwave at output of taper. Phase-adjusted taper significantly increases power capability of microwave transmission, enabling satellite-communication systems to have higher data-transmission rates.

Wilson, Jeffrey D.↗
NASA NTRS2001

Defect Density Comparison of Detached versus Attached Bridgman Grown Germanium Crystals

Semiconductor Bridgman growth without contact between the growing crystal and the growth ampoule has been observed on Earth in the last few years during several experiments. Previously, this so-called detached or dewetted growth phenomenon occurred preferentially under microgravity conditions due to the absence of the hydrostatic pressure. Many theoretical as well as experimental investigations helped to provide a better understanding of the mechanism and to identify the parameters leading to the detachment. Thus, recent attempts to get stable detached growth under terrestrial conditions by Duffar et al. growing III-V compounds and our own group with germanium and germanium-silicon alloys were frequently successful. At this conference we present the results of several germanium growth experiments performed in pyrolytic boron nitride containers. To exert an influence on the pressure ratio above and below the melt we used closed-bottom and open-bottom containers. This resulted in mainly detached-grown single crystals with the closed-bottom crucibles and attached single crystals with the open-bottom tubes. Evidence of detached growth is obtained from the crystal surface with a combination of axial profilometer scans and optical and electron microscopy. Detailed investigations of the defect structure, which is the main focus of this presentation, have shown an improvement of the crystal quality in the detached-grown samples, with a strong reduction of the etch pit density by about two orders of magnitude.

Schweizer, M.↗
NASA NTRS2005

Destructive physical analysis of hollow cathodes from the Deep Space 1 Flight spare ion engine 30,000 hr life test

Destructive physical analysis of the discharge and neutralizer hollow cathode assemblies from the Deep Space 1 Flight Spare 30,000 Hr life test was performed to characterize physical and chemical evidence of operationally induced effects after 30,372 hours of operation with beam extraction. Post-test inspection of the discharge-cathode assembly was subdivided into detailed analyses at the subcomponent level. Detailed materials analysis and optical inspection of the insert, orifice plate, cathode tube, heater, keeper assembly, insulator, and low-voltage propellant isolator were performed. Energy dispersive X-ray (EDX) and scanning electron microscopy (SEW analyses were used to determine the extent and composition of regions of net deposition and erosion of both the discharge and neutralizer inserts. A comparative approach with an un-operated 4:1:1 insert was used to determine the extent of impregnate material depletion as a function of depth from the ID surface and axial position from the orifice plate. Analysis results are compared and contrasted with those obtained from similar analyses on components from shorter term tests, and provide insight regarding the prospect for successful longer-term operation consistent with SOA ion engine program life objectives at NASA.

cathodes↗
NASA NTRS1983

Evaluation of the emission capabilities of Spindt-type field emitting cathodes

The electron emitting capabilities of Spindt-type field emitting cathodes (FEC) are being studied at the Lewis Research Center, NASA. These cathodes, having 5000 emitting points in a 1 mm diameter, have been shown to be capable of emission current densities of 10 A/sq cm and higher. The purposes of this study are to (1) demonstrate that the cathodes can be processed and used in a tube-type configuration, (2) determine whether, at a sufficiently high current density, the cathode can operate in the space charge mode, and (3) evaluate failure mechanisms in this unique type of electron emitter. FEC's have been tested in a diode configuration, by the use of pulse techniques, up to current densities of 6 A/sq cm and anode potentials of 3000 V. Space charge effects have been observed in the range of 5 A/sq cm as an apparent linear increase of cathode current with anode voltage for a constant emitter-gate potential. Failed cathodes were studied by means of scanning electron microscopy and the major failure modes encountered are attributed to gas evolution, followed by arcing, which destroys either individual emitters or a large segment of the cathode area.

Forman, R.↗
NASA NTRS1976

Experimental investigation of Stark broadening and plasma polarization shift of ionized helium resonance lines

Stark broadening and shift measurements were performed on ionized helium resonance lines from a fully ionized helium plasma in a low-inductance electromagnetic T tube. Both time-integrated photographic and time-resolved photoelectric measurements of the lines were performed with a grazing incidence spectrometer. Electron density and temperature were determined from the widths of the He II 4686-A and the He I 5876-A lines and the He II 4686-A line to continuum ratio, respectively. It was found that all ionized helium resonance lines were emitted optically thick by a homogeneous plasma slab and self-reversed by a thin cooler boundary layer. Marked blue shifts of 0.07 plus or minus 0.05 A which may be due to plasma polarization were noted.

Neiger, M.↗